铜离子印迹聚合物膜的制备及其渗透性能

采用分子印迹技术紫外光引发聚合方法制备了带支撑膜的铜离子印迹聚合膜.用扫描电子显微镜观察了膜的表面形态.膜渗透实验结果表明,通过对不同阳离子(如锌离子、钙离子等)的比较,此印迹膜对铜离子有较好的选择渗透性.分别考察了不同支撑膜、致孔剂和功能单体对膜结构及其渗透性能的影响,考察了pH值、阴离子及阳离子对膜渗透性能的的影响.结果表明,采用PVDF膜为支撑膜,乙酸铜为印迹离子合成的铜离子印迹膜,在pH值为1左右,阴离子为乙酸根离子时,对铜离子有较好的选择渗透性.     

纳米铜颗粒-酶-复合功能敏感膜生物传感器

用水合联肼作还原剂研制成亲水纳米铜颗粒,用琥珀酸二异酯磺酸钠／丙三醇／正庚烷反胶束体系合成出憎水纳米铜颗粒,并通过透射电镜和紫外光谱考察了制得的纳米颗粒样品,用憎水纳米铜颗粒及亲水纳米铜颗粒与聚 烯醇缩丁醛构成复合固酶膜基质,用溶胶－凝胶法固定葡萄糖氧化酶,构建葡萄糖生物传感器,实验结果表明,纳米铜颗粒可大幅度提高固定化酶的催化活性,响应电流从相应浓度的几十纳安增强到几千纳安,从理论和实验上证明了     

生物凝胶电镀法制备铜纳米多孔膜

采用生物凝胶电镀法制备铜纳米多孔膜。 电镀电压为5 V,阳极为铜片,实验探究了电镀液成分、电镀时间、阴极衬底及沉积电压对电镀层表面形貌的影响。 采用扫描电子显微镜(SEM)和X射线衍射(XRD)对样品形貌和晶型进行表征,得出制备铜膜的最佳条件。 结果表明,电镀的铜膜颗粒尺寸在100 nm左右,晶粒平均尺寸为25 nm,存在较强的(111)织构,而且XRD结果表明,附着的壳聚糖凝胶对铜膜有保护作用,防止其被氧化。 同时采用电化学工作站对其过程中的电镀电流进行实时测量,电流变化曲线表明电镀进行到一定时间后,电流趋于一个很小的稳定值,壳聚糖凝胶阻止了镀液中铜离子的进一步沉积。     

原子吸收光谱法测定三醋酸纤维素膜中铜铁

运用空气-乙炔火焰原子吸收光谱法同时测定银锌电池三醋酸纤维素膜中铜铁含量，并对测定条件和干扰因素进行了综合分析．该测定方法具有很好的灵敏度，干扰少，选择性和重现性好等优点．测定样品铜铁含量的相对标准偏差均小于1．0％．标准加入回收率均在97．3％-98．8％范围内．完全适用于银锌电池三醋酸纤维素膜中铜铁含量的控制和样品系统分析．     

无脂链磺化酞菁铜多层膜体系：电子非弹性平均自由程的研究

磺化酞菁铜多层膜体系是利用Langmuir-Blodgett技术制备的有序有机分子膜,它对于XPS测试有很好的稳定性,本文在固定电子出射角的条件下利用XPS方法研究了不同厚度的膜样品中Cu_((2(?))_(3/2))、Ni_(1(?))、S_(2p)峰强度的变化规律,讨论了膜内分子有序排列引起的散射效应对电子平均自由程的影响。     

铜锆复合氧化物的结构对其催化选 择还原－氧化氮性 能的影响

用浸渍法和共沉淀法分别制得CuO---ZrO~2复合氧化具物有不同的选择还原NO~x的催化性能,采用XRD,BET,EXAFS和H~2---TPR等手段对样品进行了表征,发现浸渍法制备的样品具有的比表面较大,氧化锆被稳定在四方相。EXAFS实验表明,浸渍法制得样品的铜离子填入氧化锆表面空穴中,并以Cu^2+形式存在;500℃焙条件下用共沉淀法引入的铜离子可部分取代锆离子,在氧化锆体相高度分散形成均匀的无定形固溶体,铜离子在氧化锆体相的高度分散是形成表面弧立铜物种的关键。溶入氧化锆体相的铜离子在取代部位由于局部负电荷而使氧化性降低,是共沉淀法制备样品具有较高催化活性的主要原因。     

铜锆复合氧化物的结构对其催化选 择还原－氧化氮性 能的影响

用浸渍法和共沉淀法分别制得CuO---ZrO~2复合氧化具物有不同的选择还原NO~x的催化性能,采用XRD,BET,EXAFS和H~2---TPR等手段对样品进行了表征,发现浸渍法制备的样品具有的比表面较大,氧化锆被稳定在四方相。EXAFS实验表明,浸渍法制得样品的铜离子填入氧化锆表面空穴中,并以Cu^2+形式存在;500℃焙条件下用共沉淀法引入的铜离子可部分取代锆离子,在氧化锆体相高度分散形成均匀的无定形固溶体,铜离子在氧化锆体相的高度分散是形成表面弧立铜物种的关键。溶入氧化锆体相的铜离子在取代部位由于局部负电荷而使氧化性降低,是共沉淀法制备样品具有较高催化活性的主要原因。     

酞菁化合物LB单分子膜的SERRS

酞菁类化合物具有优良的光电特性,选择适当的取代侧链可得到稳定的LB成膜材料,可望在微电子器件等方面获得重要的应用.本工作观测了四-4-(2,4-二特戊基苯氧基)酞菁铜(CuPc(Dt-PP)_4)在银岛膜上的LB单分子层的表面增强共振拉曼散射(SERRS)光谱。比较其固体粉末的共振拉曼散射(RRS)光谱,讨论了酞菁铜分子大环在载片表面的取向及其可能的原因。1 实验CuPc(Dt-PP)_4样品由陈文启等合成,经元素分析、IR、NMR、色谱等研究确认其结构如图1所示.银岛膜用真空蒸镀法制备在玻璃载片上。用同时蒸镀在铜网上的银膜的透射电     

用于透射电子显微镜表征的单层纳米晶/聚合物复合薄膜的制备

为了提高纳米晶的TEM表征质量, 通过在水/气两相界面上铺展纳米晶/聚合物复合单层膜的方法, 制备了质量较高的TEM样品. 对于水相纳米晶采用表面活性剂再包覆的方法, 将其转移到油相. 与传统制样方法(尤其是水相合成纳米晶)相比, 嵌入聚合物膜中的纳米晶更容易分散(受到空间位阻与分子间弱相互作用等因素的影响), 并且聚合物膜可以自支持在空的铜网上, 从而提高了TEM照片的清晰度. 研究了系统中聚合物、纳米晶、表面活性剂和溶剂的种类及配比关系对于样品和成像质量的影响, 结果表明, 该方法对各种金属及半导体纳米晶的TEM表征具有一定的普适性.     

碳膜的制备及其在纳米颗粒观察中的应用

阐述了透射电镜中碳膜的制备方法，并讨论了影响碳膜质量的因素，用这种碳膜支持纳米颗粒在透射电镜下观察，碳膜在电子束的长时间照射下，不姓变形和起皱图象清晰衬底均匀。     

Defect of nanocrystalline copper and silver

Ｎａｎｏｓｃａｌｅｍａｔｅｒｉａｌｓａｒｅｔｈｅｉｍｐｏｒｔａｎｔｐａｒｔｏｆｎａｎｏｓｃｉｅｎｃｅａｎｄｔｅｃｈｎｏｌｏｇｙ.Ｔｈｅｓｔｕｄｙｏｆｎａｎｏｃｒｙｓｔａｌｌｉｎｅｍａｔｅｒｉａｌｓ’ｓｔｒｕｃｔｕｒｅｉｓｃｌｏｓｅｌｙｃｏｎｎｅｃｔｅｄｗｉｔｈｔｈｅｉｒａｐｐｌｉｃａｔｉｏｎ.Ｔｈｅｒｅｆｏｒｅ,ｔｈｅｓｔｒｕｃｔｕｒｅｓｔｕｄｙｏｆｎａｎｏｃｒｙｓｔａｌｌｉｎｅｍａｔｅｒｉａｌｓａｔｔｒａｃｔｓｐａｒｔｉｃｕｌａｒｉｎｔｅｒｅｓｔｉｎｔｈｅｒａｐｉｄｄｅｖｅｌｏｐｍｅｎｔｏｆｈｉ…     

纳米Na_2SiF_6的电化学制备、表征与荧光性质

采用溶胶-凝胶法在Ti表面修饰一层纳米TiO2(nanoTiO2)膜,经X射线粉末衍射(XRD)和扫描电镜(SEM)表征,证明多孔TiO2膜的平均孔径为80 nm.以该多孔膜电极为模板,借助电化学沉积的方法制备了纳米Na2SiF6(nano Na2SiF6).经XRD和透射电镜(TEM)测试证实该Na2SiF6为均一的白锰钒型结构,平均粒径约为20 nm.初步研究了其荧光性质,发现在452.4 nm和285 nm处分别有强的荧光发射峰和激发峰.     

Fabrication and mechanical durability of a superhydrophobic copper surface with morphological development from hydrothermal reaction

The superhydrophobic surface on copper is fabricated by using a simple hydrothermal reaction and subsequent perfluorosilane treatment. The micro‐structured and nano‐structured surface was directly obtained through the hydrothermal reaction of copper sheets with sulfur at 180 °C for 12 h, resulting in the formation of copper sulfide film on the copper substrate. The chemical composition of this film was confirmed using X‐ray photoelectron spectroscopy. After copper sulfide film is treated by perfluorosilane, the superhydrophobic surface with static water contact angle of 153 °C and a low contact angle hysteresis is achieved. The superhydrophobic surface shows strong mechanical stability and can effectively protect the copper substrate. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation of Au-TiO2 Hybrid Nano Particles in Silicate Film Made by Sol-Gel Method

TiO₂ nano particles with photo catalytic property were mixed with silica alkoxides solution with HAuCl₄/4H₂O. STS02 (purchased from Ishihara Sangyo Kaisha, Ltd.) was used as TiO₂ nano particles. The average size of TiO₂ nano particles was 7 nm in diameter. The gel film coated on glass substrate was heated and then HAuCl₄/4H₂O was thermally reduced at 390 degree. The coated silica gel film doped with HAuCl₄/4H₂O and TiO₂ nano particles was turned into light blue from colorless gel film after heat treatment. The optical absorption spectrum showed the absorption peak of the film heated at 390 degree shifted to at about 650 nm compare to SiO₂ film doped with Au nano particles without TiO₂ nano particles that had absorption peak at 542 nm. On the other hand, the film formed from coating solution incorporated TiAA (titanium tetraisopropoxide chelated by acetyl acetone) as TiO₂ source instead of TiO₂ nano particles had absorption peak at 550 nm. That means there was no effect on formation of Au nano particles when TiAA was incorporated. The average size of the particles was found to be about 23 nm in diameter by TEM observation. Furthermore EDX (Energy Dispersive X-ray Fluorescence Spectrometer) analysis of nano particles in the film indicated that Au-TiO₂ nano hybrid particles were formed. Simulation results also supported that the size in diameter of Au nano particles had little influence on the absorption coefficient of the silica film doped with Au nano particles.     

Surface Modification of Nano－SiO2 by Grafting PMMA／PBA

The surface of nano-SiO2 was modified by being encapsulated with hydroxy-propyl-methyl cellulose (HPMC), and then co-grafted with acrylates. The grafting conditions, such as pH of the medium, and initiator concentration have been studied. The modified nano-SiO2 particles were characterized by TEM, DSC and FT-IR spectra. TEM images show that the surface of the nano-particles has been successfully modified by a thick layer of film-like polymer in this way. The DSC results show that the decomposition temperature of modified nano-particles of SIO2 is 90 ℃ higher than that of grafted-on polymer. According to the FT-IR spectra, It is convinced that poly-methyl methacrylate ( PMMA ) and poly-acrylic butyl-ester ( PBA ) were co-grafted onto the surface of nano-SiO2.     

Nano silver coated patterned silica thin film by sol–gel based soft lithography technique

We report the fabrication of nano silver coated patterned silica thin film by sol–gel based soft lithography technique. Initially, silica gel film on soda lime silica glass was prepared by dipping technique from a silica sol of moderate silica concentration. A PolydimethylSiloxane elastomeric stamp containing the negative replica of the patterns of commercially available compact disc was used for embossing the film and the embossed film was cured up to 450 °C in pure oxygen atmosphere for oxide film. Finally, a precursor solution of AgNO₃ in water containing polyvinyl alcohol as an organic binder was made and used for coating on the patterned silica film by dipping technique and cured the sample up to 450 °C in reducing gas atmosphere to obtain nano silver layer. The formation of only cubic silver (~4.0 nm) and both cubic silver (~5.2 nm) and silver oxide (~3.6 nm) crystallites at 350 and 450 °C film curing temperatures respectively were confirmed by XRD measurements. The % of nano silver metal and silver oxide were 75.4 and 24.6 respectively. The nano-structured surface feature was visualized by FESEM whereas AFM revealed the high fidelity grating structure of the films. Presence of both spherical and rectangular structure (aspect ratio, 2.37) of nano silver/silver oxide was confirmed by TEM. The films were also characterized by UV–Vis spectral study. The patterned film may find application in chemical sensor devices.     

负载型纳米非贵金属催化剂上CO的氧化行为Ⅱ.纳米铜的制备、结构及催化性能

用惰性气体蒸发法和电弧等离子体法制备了纳米铜粒子，用物理干法将其担载到载体上，并用于催化ＣＯ氧化反应．用ＴＥＭ，ＸＲＤ，ＳＥＭ对纳米粒子和催化剂进行了表征．结果表明，载体、氧化气氛及制备工艺均影响催化剂的活性，稀土元素铈的存在能提高铜的催化活性，纳米铜在催化过程中将转变为氧化物．     

TiO2/聚丙烯酸丁酯纳米复合薄膜的制备及结构表征

利用微乳液原位聚合法在普通玻璃表面上制备了TiO2/聚丙烯酸丁酯纳米复合膜.采用傅立叶变换红外光谱、高分辨透射电子显微镜和X射线光电子能谱对膜的结构进行了表征.结果表明， TiO2以纳米线的形式弥散在聚丙烯酸丁酯的高分子网络中，并且所制备的TiO2纳米线具有板钛矿相结构.     

Copper (II)-Surfactant Complex and Its Nano Analog as Potential Antitumor Agents

The in vitro anticancer activity of copper cetyl trimethyl ammonium bromide (Cu-CTAB)-loaded cyclodextrin nanoparticles on Ehrlich ascites carcinoma (EAC), colon cancer cells (HCT 116), liver cancer cells (HepG-2), breast cancer cells (MCF-7), and cervix cancer cells (Hela) was investigated using MTT due assay. Cyclodextrin nanoparticles loaded with Cu-CTAB exerted in vitro anticancer activity against the previous human cancer cell lines comparable to the activity of free non-entrapped in nanoparticles macro-particle Cu-CTAB. The nano analog was synthesized by physical loading using grinding with ball mill. The ratio between Cu-CTAB and cyclodextrin oligosaccharide was 1 Cu-CTAB: 3 cyclodextrin. The particle size of the nano derivative was determined using the transmitted electron microscope (TEM).     

Investigation of molybdate–benzotriazole surface treatment against copper tarnishing

The synergistic effect of benzotriazole (BTAH) and molybdate on the inhibition of copper tarnish was studied in this paper. The antitarnish treatment of copper was conducted with BTAH solution containing molybdate. The surface morphology observation and composition analysis were investigated by SEM with energy dispersive X‐ray (EDX) spectroscopy. The addition of molybdate improved the protection of BTAH significantly. The BTAH + molybdate treated copper specimen has higher N concentration in its surface. The structure of the protective film was studied by XPS and AES measurements. It was characterized to be a complex of Cu(I)BTA. The antitarnish effect is certified by the formation of the protective Cu(I)BTA film. Molybdate does not participate in the formation of the protective film. The presence of molybdate promotes the passivation of copper. This facilitates the stabilization of the cuprous oxide film, and strengthens the adsorption of BTAH. Copyright © 2008 John Wiley & Sons, Ltd.