火焰原子吸收光谱法测定天然气转化催化剂中的氧化钾

建立火焰原子吸收光谱法测定天然气转化催化剂中氧化钾的分析方法。该方法将催化剂样品和助溶剂四硼酸锂熔融后再用盐酸溶解定容,采用火焰原子吸收光谱仪对样品溶液进行测定。在优化的实验条件下,钾离子的质量浓度在0.05~0.50 mg/L范围内与吸光度呈良好线性关系,相关系数为0.9995。钾的方法检出限为0.001 mg/L,定量限为0.01 mg/L,测定结果的相对标准偏差为2.6%~4.3%(n=6),样品加标回收率为97.8%~102.3%。与HG/T 3543-2014中的酸溶制样法相比,该方法能够将催化剂样品中的难溶钾盐溶出,分析结果准确度更高,可用于天然气转化催化剂中氧化钾含量的测定。     

火焰原子发射光谱法测定电解铝中痕量钾

建立了火焰原子发射光谱法检测电解铝中痕量钾的方法。用稀王水(1:1,V/V)边加热边溶解电解铝样品,冷却后转移到100 m L容量瓶,待用;为消除铝基体干扰,标准工作溶液需加入适量的铝,火焰原子发射光谱法直接测定。方法线性范围为0.010~0.120μg/m L,检出限(3σ)为0.4 ng/m L(n=11),连续9次测定0.040μg/m L钾标准工作溶液,其RSD为0.72%。分析了3种电解铝样品中钾含量,回收率范围为90.0%~100.0%。该方法可用于电解铝样品中痕量钾的检测。     

火焰原子吸收光谱法测定粗锌中的铜

建立火焰原子吸收光谱法测定粗锌中的铜含量。采用硝酸–酒石酸溶解样品,并以其为测定溶液介质,检测波长为324.7 nm,以水为参比,采用空气–乙炔火焰以原子吸收光谱仪进行测定。在优化的实验条件下,铜的质量浓度在0.10~2.50μg/m L范围内与吸光度有良好线性关系,相关系数为0.999 7,方法检出限为0.01μg/m L。测定结果的相对标准偏差为1.0%~3.0%(n=11),样品加标回收率为97%~102%。该方法具有灵敏度高,干扰少,重现性好等优点,适用于铜含量在0.001%~0.50%之间的粗锌中铜的测定。     

气相色谱法测定甘宝素中的甲苯残留量

采用毛细管气相色谱法快速测定甘宝素产品中的甲苯残留量。样品经甲醇稀释,氢火焰离子化检测器检测,外标法计算含量。甲苯的质量浓度在3.2~25.6 mg/L范围内与色谱峰面积线性良好,相关系数r=0.999 3,方法的检出限为1.16 mg/L,样品的加标回收率为96.5%~102.8%(n=6),测定结果的相对标准偏差为3.2%~4.5%。该方法操作简便,灵敏度高,适合于实际生产中甲苯残留量的快速测定。     

火焰原子吸收光谱法测定锌合金中镁

建立火焰原子吸收光谱法测定锌合金中镁含量。选用10 mL盐酸溶液(1+1)溶解样品,加入5 mL质量浓度为100 g/L的LaCl3溶液,以消除铝对镁的化学干扰,在选定的仪器工作条件下进行测定。结果表明,镁的质量浓度在0~1.238 mg/L范围内与与吸光度具有良好的线性关系,相关系数为0.999 4,线性方程为Y=1.086 4X+0.018 5,方法测定下限为0.010 mg/L。样品测定结果的相对标准偏差为1.61%~3.45%(n=6),加标回收率为91.3%~94.7%。该方法准确度高,精密度好,满足锌合金中镁含量的日常检测要求。     

火焰原子吸收光谱法测定氧化石墨烯中铁和钾的含量北大核心CSCD

取0.10 g氧化石墨烯样品于铂金坩埚中,采用120℃干燥4 h、220℃灰化4 h、1000℃灼烧2 h及用混酸溶解残留氧化物的前处理方式,在分析谱线Fe 248.3 nm及K 766.5 nm、狭缝宽度0.2 nm(Fe)和0.5 nm(K)、火焰燃气乙炔流量1.0 L·min^(-1)、助燃气空气流量4.0 L·min^(-1)条件下,采用火焰原子吸收光谱法测定其中铁和钾的含量。结果表明,铁和钾标准曲线的线性范围均为0.020%~0.500%,检出限(3s)均为0.001%,氧化石墨烯样品中铁和钾测定值的相对标准偏差(n=12)为0.70%~7.6%。按标准加入法进行回收试验,铁和钾的回收率为94.0%~106%。方法用于测定实际样品,测定值与文献中电感耦合等离子体原子发射光谱法所得结果基本一致。     

正交试验在火焰原子吸收光谱法测定汽车制动液中金属元素含量的应用

运用正交试验设计确定了AA280FS型火焰原子吸收光谱仪测定各金属元素的最佳工作条件,并采用极差分析和方差分析对各因素影响程度进行考察。采用干灰化法处理汽车制动液样品,在优化火焰原子吸收光谱(FAAS)条件下测定Cr、Cu、Fe和Mn的含量,测定检出限(mg/L)Cr:0.0444,Cu:0.0201,Fe:0.0251,Mn:0.0735;加标回收率为96.1%~105.2%;相对标准偏差为1.23%~2.18%(n=6)。该方法分析结果与电感耦合等离子体原子发射光谱(ICP-AES)进行比较,测定值吻合,且准确度和精密度较好,更经济实用,容易推广。     

火焰原子吸收光谱法测定铼产品中的痕量钠

建立了火焰原子吸收光谱法测定高铼酸、高铼酸铵、铼粉中痕量钠的方法,对样品的预处理和测定钠的条件进行了研究。结果表明:水溶解法、硝酸溶解法或硝酸-硫酸溶解法溶解样品完全,测得钠的结果吻合;于选定条件下,钠的测定浓度在0.020 0~0.500 0μg/mL范围内线性良好;测定高铼酸、高铼酸铵和铼粉样品中0.27~0.47mg/L、0.000047%~0.00048%和0.000040%~0.00049%的钠含量,检出限、相对标准偏差(RSD,n=7)、加标回收率分别为高铼酸3×10-4μg/mL、6%~10%、98%~102%,高铼酸铵3×10-4μg/mL、8%~9%、96%~102%和铼粉3×10-4μg/mL、5%~9%、96%~103%。方法结果准确、分析快速、操作简便,应用于实际的样品分析,结果满意。     

气相色谱法测定溶剂型涂料中环己酮含量

建立测定溶剂型涂料中环己酮含量的气相色谱(GC)检测方法。样品在乙酸乙酯中超声提取,以ZB–WAX毛细管柱(30 m×0.25 mm,0.25 μm)为分离色谱柱,加入十四烷作为内标物,氢火焰离子化检测器(FID)检测,内标法定量。结果表明,环己酮的质量浓度在10~250 mg/L范围内呈良好的线性关系,相关系数r=0.999 9。以阴性涂料样品为样品基质,加标平均回收率在92.5%~97.8%之间,测定结果的相对标准偏差在0.87%~1.77%(n=7)之间,方法检出限为13 mg/kg。采用该方法对15种溶剂型涂料样品进行测定,其中11种检出环己酮。该方法能使目标化合物得到有效分离,分析时间短,重复性好,灵敏度高,适用于溶剂型涂料中环己酮含量的快速测定。     

气相色谱法测定1-(5-溴-1H-吲唑-1-基)乙酮

建立了测定1-(5-溴-1H-吲唑-1-基)乙酮纯度的气相色谱法。采用DB–5型色谱柱,程序升温,火焰光度检测器,外标法定量,1-(5-溴-1H-吲唑-1-基)乙酮在100~1 000 mg/L范围内内线性关系良好,检出限为0.01mg/L。测定结果的相对标准偏差为1.67%~1.89%(n=5),样品加标回收率为98.1%~107.9%。用该方法测定了自制的1-(5-溴-1H-吲唑-1-基)乙酮样品的纯度。该测定方法准确度高、专属性较强且灵敏度较高,适用于1-(5-溴-1H-吲唑-1-基)乙酮的质量控制。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.