钴负载量和焙烧温度对F-T合成用Co/Al2O3催化剂活性的影响

 对用于F－T合成制液态烃的Co／Al2O3催化剂进行了程序升温还原研究,确定了合适的还原活化温度（约600～800K）,同时考察了钴负载量和焙烧温度对催化剂活性的影响．结果表明,钴负载量和焙烧温度对C5＋收率的影响十分显著．用CODEX优化软件对钴负载量和催化剂焙烧温度进行了优化．结果表明,比较理想的钴负载量为11．6％,焙烧温度为651K．XRD测试结果表明,在较高温度焙烧的催化剂由于易生成CoAl2O4尖晶石,导致催化剂的活性显著降低．     

Co/Hβ催化剂上N_2O的分解性能研究

采用浸渍法制备了Hβ分子筛负载钴氧化物催化剂。考察了催化剂焙烧温度和钴负载量对催化剂催化分解N2O活性的影响,并采用XRD、NH3-TPD、H2-TPR、SEM等手段对催化剂的理化性质进行表征。结果表明,催化剂中的钴物种主要以Co3O4尖晶石型形态存在;催化剂焙烧温度显著影响其酸性和酸量及氧化还原性能,焙烧温度达到700℃后,催化剂中有难还原的Co-Al-O物种生成。焙烧温度和钴负载量对催化剂的催化活性均有影响,焙烧温度为600℃、钴负载量为10%~15%的催化剂催化活性好,N2O分解温度低,t10、t50和t95分别为325~329℃、364~367℃和406~408℃。     

Effects of calcination and reduction temperature on the performance of Co-Pt-ZrO2/γ-A12O3 catalysts for Fischer-Tropsch synthesis

采用浸渍法制备了Co-Pt-ZrO2/γ-Al2O3催化剂,对其进行了BET、XRD和TPR等表征,并在浆态床反应器上考察了焙烧温度和还原温度对催化剂费托合成反应性能的影响.结果表明,焙烧温度过高,容易造成Co物种和载体间的相互作用增强,使部分氧化钻颗粒聚集或烧结,导致催化剂的F-T合成反应活性和C5+烃选择性降低.还原温度较低时,钴物种不能充分还原,CO加氢活性低,甲烷选择性高,重质烃选择性低;还原温度过高,则可能造成活性物种的烧结,反而降低了催化剂的活性和重质烃选择性.在原料气n(H2)/n( CO)=2.0、483 K、2.4 MPa和空速3.6 L/( gcat·h)的条件下,31.08％ Co～0.11％Pt ～ 7.16％ ZrO2/Al2O3催化剂在673 K焙烧.纯H2下653 K还原后,其费托性能最佳;CO转化率为27.0％,C5+的选择性为83.0％.     

氧化态Co/γ-Al_2O_3催化剂的结构与反应性能研Ⅰ.活性及体相、表相结构表征

采用等量浸渍法 ,制得 5 0 0、 6 0 0、 75 0和 95 0℃焙烧的 Co/ γ- Al2 O3催化剂 ;考察了它们对 CO氧化和乙烯选择还原 NO的反应性能 ;用 XRD和 XPS方法表征了催化剂的体相与表相结构 .活性测试结果表明 ,随焙烧温度升高 ,样品对 CO的氧化活性呈下降趋势 ;对乙烯选择还原 NO反应 ,活性先上升 ,而后又有所下降 (当焙烧温度高于 75 0℃时 ) .从硝酸钴制得的样品 ,其氧化活性要高于从醋酸钴制得的样品 ,但对乙烯选择还原 NO,后者的活性更好 .结构表征结果表明 ,催化剂中钴物种的存在形式与原料盐类及焙烧温度密切相关 .在 Co/ γ- Al2 O3催化剂中主要存在两种钴相 ,即 Co3O4和非化学计量的 Cox Al( 8/ 3- 2 x/ 3) O4尖晶石相 ,前者为完全氧化活性中心 ,后者是 NO选择还原的活性中心 .在相同焙烧温度下 ,以醋酸钴为原料时 ,更容易形成 Cox Al( 8/ 3- 2 x/ 3) O4尖晶石相 .随着焙烧温度提高 ,活性组分与载体的相互作用加强 ,Co3O4相逐步向 Cox Al( 8/ 3- 2 x / 3) O4尖晶石相转化 ,这可能是样品氧化活性下降和选择还原活性升高的主要原因 .在更高焙烧温度下 ,随着 Cox Al( 8/ 3- 2 x / 3) O4尖晶石相颗粒度的增加和晶形改变 ,以及钴离子由表相向体相的迁移 ,使样品比表面积下降 ,表面氧空位及活性位减少 ,     

乙醇水蒸气重整Co/CeO2催化剂

 采用共沉淀法制备了Co/CeO2催化剂并将其应用于乙醇水蒸气重整制氢反应,考察了活性组分含量和焙烧温度对催化剂性能的影响. 结果表明,在原料气水∶乙醇∶N2摩尔比为3∶1∶16, 空速为40 L/(g·h)和反应温度为350～600 ℃的条件下, 经650 ℃焙烧的10%Co/CeO2催化剂对乙醇水蒸气重整制氢反应具有高活性和高选择性. 在500 ℃下进行的40 h稳定性测试中,该催化剂上的乙醇转化率始终接近100%, 反应后气体中的H2含量保持在65%左右. X射线衍射表征结果显示,焙烧后催化剂的主要物相组成为Co3O4和CeO2, 二者之间存在相互作用. Co/CeO2催化剂中钴的主要存在形式包括小晶粒的钴氧化物、大晶粒Co3O4和进入CeO2晶格的钴,Co3O4含量和焙烧温度的改变可影响催化剂中钴的存在形式. 由催化剂中高分散小晶粒的钴氧化物还原所得的金属钴是关键的活性组分.     

N_2O在Mg-Fe复合氧化物上的催化分解(英文)

用共沉淀法制备了一组Mg-Fe复合氧化物催化剂,用于N2O催化分解,考察了催化剂组成、焙烧温度、负载助剂钾等参数对其催化活性的影响。采用N2物理吸附、X射线衍射、H2-程序升温还原等技术对催化剂进行了结构表征。结果表明,500℃焙烧的Mg0.6Fe0.4Fe2O4催化剂对于N2O分解反应有较高活性,而K改性的催化剂活性均有所降低,且K的负载量越高,改性催化剂的活性越低,这是由于负载的K粒子抑制了表面铁物种的还原,降低了催化剂的比表面积。在有氧无水、水氧共存条件下连续反应10h,Mg0.6Fe0.4Fe2O4的催化活性和稳定性均显著高于FeOx催化剂。     

预处理条件对Pt/Al2O3催化还原NO的活性影响

用溶胶-凝胶法制备Al2O3载体,浸渍法制备质量分数为0.5%的Pt/Al2O3催化剂.研究焙烧气氛和温度对选择性催化还原NO反应活性和Pt价态的影响.结果表明,H2焙烧的活性温度区间最宽,随着焙烧温度的升高,温度区间变化很小,523K下O2焙烧的催化剂活性最好,且活性区间向高温方向移动.活性现象用程序升温脱附实验(NO-TPD,NO-O2-TPD)进行了解释.XPS研究表明,523K下O2用焙烧Pt的主要价态是Pt2+,而523K下H2和N2焙烧Pt的主要价态为Pt0.     

V_2O_5/C催化乙二醛氧化为乙醛酸的研究

选用V2O5作为催化剂,活性炭为载体,偏钒酸铵的草酸溶液为浸渍前驱体,采用等体积浸渍法制备了V2O5/C催化剂,将其应用于乙二醛的液相氧化.并对反应液用液相色谱进行了定性,在确定了催化体系中氧化产物的基础上,考察了V2O5含量和焙烧温度对催化剂催化性能的影响,利用XRD和TEM等手段对催化剂进行了表征.结果显示,V2O5含量较低时(w(V2O5)<3%),催化剂的活性组分分散度较高,乙二醛转化率和乙醛酸的选择性都随着V2O5的含量提高而逐渐增加;当负载量为3%时,催化效果最佳,乙二醛转化率和乙醛酸的选择性分别达到16.16%和76.75%;当V2O5的质量分数大于3%时,V2O5颗粒在活性炭表面发生明显聚集,V2O5开始出现多层吸附,导致乙二醛转化率和乙醛酸得率略有下降.而焙烧温度是制备负载型催化剂的一个重要影响因素.焙烧温度的作用不仅在于使活性组分的前驱体充分分解,同时也影响着活性组分的分散状态.我们考察了经不同温度焙烧后的催化剂的活性,从表征结果来看,在473K以下焙烧时,可能活性组分的前驱体未能充分分解,活性中心数目较少,反应效果较差;当V2O5负载量为3%、焙烧温度为573K时,催化剂具有较高的催化活...     

镍基催化剂上糠醛选择性加氢合成糠醇

采用浸渍法制备了一系列负载的Ni催化剂,用于糠醛选择性加氢反应.用XRD、TPR等手段对Ni/γ-Al2O3样品进行了表征.结果表明,Ni负载量在5~|15%范围内,高度分散于载体γ-Al2O3表面,Ni负载量进一步提高到20%,则在载体表面聚集成为微晶.在10%Ni/γ-Al2O3样品上提高焙烧温度有利于Ni的前驱体分解且高度分散于载体表面.Ni2 与γ-Al2O3存在较强的相互作用,但这种相互作用随着Ni负载量的增加而逐渐减弱,随着焙烧温度的增加而逐渐增强.与其他载体负载的Ni催化剂相比,Ni/γ-Al2O3由于其大的表面和适当的表面结构,在糠醛加氢反应中表现出一定的活性和较高的选择性,且随着Ni负载量的增加,活性逐渐增强,但选择性有所下降.另外催化剂的焙烧温度、还原温度,反应温度和溶剂对该反应均有较大影响,采用极性有机溶剂,适宜的焙烧和还原温度有利于催化剂活性和选择性的提高.     

KNO3/MCM-48催化酯交换法合成碳酸二丙酯

 对KNO3/MCM-48用于丙醇和碳酸二甲酯进行酯交换合成碳酸二丙酯的催化性能进行了考察. 用X射线衍射(XRD)、红外光谱(IR)和X射线荧光法研究了催化剂的结构特征和表面性质. XRD结果表明,随着K负载量的增加,载体特征峰强度逐渐减弱,但仍保留MCM-48的晶体结构. 随着焙烧温度的升高, KNO3逐渐分解成K2O. 分别考察了活性组分负载量、焙烧温度、焙烧时间和催化剂的用量以及反应时间对反应的影响. 结果表明, KNO3/MCM-48催化剂对碳酸二丙酯的合成具有很高的催化活性. 在反应温度363 K, 反应时间6 h, 催化剂用量5%, 丙醇与碳酸二甲酯摩尔比为4的条件下,碳酸二甲酯的转化率可达99.9%, 产物碳酸二丙酯选择性93.4%, 产率93.3%.     

Hydrogen generation from methanolysis of sodium borohydride over Co/Al2O3 catalyst

Co/Al2O3 catalyst is prepared with an impregnation-chemical reduction method and used to catalyze the methanolysis of sodium borohydride (NaBH 4) for hydrogen generation.At solution temperature of 0 C,the methanolysis reaction can be effectively accelerated using Co/Al2O3 catalyst and provide a desirable hydrogen generation rate,which makes it suitable for applications under the circumstance of low environmental temperature.The byproduct of methanolysis reaction is analyzed by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR).The characterization results indicate that methanol can be easily recovered after methanolysis reaction by hydrolysis of the methanolysis byproduct,NaB(OCH 3) 4.The catalytic activity of Co/Al2O3 towards NaBH 4 methanolysis can be further improved by appropriate calcination treatment.The catalytic methanolysis kinetics and catalyst reusability are also studied over the Co/Al2O3 catalyst calcined at the optimized temperature.     

制备方法及焙烧温度对Co3O4/CeO2催化剂上CO低温氧化反应的影响

 分别采用沉淀氧化法、均匀沉淀法及络合燃烧法制备了Co3O4/CeO2复合氧化物催化剂,并在干燥及湿气条件下进行了CO氧化反应. 结果表明,采用沉淀氧化法经538 K焙烧制得的Co3O4/CeO2催化剂具有优异的CO低温氧化活性和较高的抗湿性能. 在196 K条件下,该催化剂上CO氧化的转化率为99%, 并且可连续保持400 min以上; 当温度上升到298 K时,经过 2400 min反应后, CO的转化率仍可达到94%; 当反应气中含3.1%湿气,温度为383 K时,经过2400 min反应后, CO的转化率仍保持在79%. 实验表明, Co3O4/CeO2催化剂的制备方法及焙烧温度对Co3O4与CeO2之间的相互作用有显著的影响,进而影响催化剂催化CO低温氧化的活性.     

助剂CeO2对Co/Al2O3催化剂上F-T合成反应性能的影响

 在用于F－T合成的Co／Al2O3催化剂中加入少量助剂,能够提高CO转化率和C5＋烃选择性．主要考察了助剂CeO2添加量和催化剂焙烧温度等因素对F－T合成反应的影响,并通过程序升温还原、程序升温氧化及X射线衍射等手段对催化剂进行了表征．结果表明,在Co／Al2O3催化剂中加入少量CeO2（n（Ce）／n（Co）＝0．1～0．14）,能够有效提高催化剂的催化活性和C5＋烃选择性;焙烧温度则以相反的趋势控制F－T反应活性和链增长几率;助剂的加入降低了催化剂的起始还原温度,改善了催化剂的还原性能．但是,催化剂的积碳量有所增加,经10h反应后,催化剂上存在两种类型的积碳．     

Effects of pretreatment and reduction on the Co/Al2O3 catalyst for CO hydrogenation

The purpose of this study was to investigate the effect of preadsorbed CO at different temperatures, calcination temperatures, the combined influence of reduction temperature and time, and pretreatment using hydrogen or syngas as reduction agents on the F-T synthesis （FTS） activity and selectivity of Co/Al2O3 catalyst. The reactivity of the carbon species at higher preadsorption temperature with H2 in TPSR decreased, whereas the carbon-containing species showed higher reactivity over Co/Al2O3 catalyst with low calcination temperature. This agreed well with the order of catalytic activity for F-T synthesis on this catalyst. The catalytic activity of the catalyst varied with reduction temperature and time remarkably. CODEX optimization gave an optimum reduction temperature of 756 K and reduction time of 6.2 h and estimated C5＋ yield perfectly. The pretreatment of Co/Al2O3 catalyst with different reduction agents （hydrogen or syngas） showed important influences on the catalytic performance. A high CO conversion and C5＋ yield were obtained on the catalyst reduced by hydrogen, whereas methane selectivity on the catalyst reduced by syngas was much higher than that on the catalyst reduced by hydrogen.     

碳纳米管负载四氧化三钴催化剂的载钴量分析

针对碳纳米管作催化剂载体材料的特性，采用灼烧灰化预处理，间接碘量法测定了Co3O4／CNTs载钴量，获得稳定而准确的分析结果。结果表明，制备Co3O4／CNTs催化剂时所加入的钴并不全部吸附在碳纳米管上；载钴效率随着碳纳米管载钴量的增加而降低。     

Co/Al2O3催化剂上3-甲基-2-丁烯醛选择性加氢反应

3-甲基-2-丁烯醛(3-MeCal)是一种典型的α,β-不饱和醛,其C=O加氢产物3-甲基-2-丁烯醇(3-MeCol)作为重要的有机中间体,在医药、香料、农药等生产领域有着广泛的应用.我们采用沉积沉淀法制备了Co/Al2O3催化剂,将其应用于3-MeCal液相选择性加氢反应中,考察了反应温度、H2初始压力、催化剂焙烧温度和还原温度对3-MeCal选择性加氢反应的影响.发现反应温度为80℃,H2初始压力为1×106Pa下,加氢反应效果良好.通过H2-TPR与XRD表征了焙烧温度对催化剂的影响,发现适当焙烧温度能增强Co物种与载体Al2O3间作用力.焙烧温度为600℃,还原温度为550℃下制备的催化剂反应48 min后转化率为23.0%,3-MeCol选择性达到88.6%.制备的Co/Al2O3催化剂具有良好的磁性,在外磁场作用下可与液相反应体系实现高效分离,循环使用3次后,催化性能没有明显下降,表现出良好的循环使用性能.     

Fischer-Tropsch synthesis on anchored Co/Nb2O5/Al2O3 catalysts: the nature of the surface and the effect on chain growth

A series of Co/x%Nb2O5/Al2O3 catalysts were prepared by anchoring niobia on an Al2O3 support at different niobia concentrations. Characterization of the structure and nature of surface active sites was attempted in order to correlate the CO hydrogenation activity of these systems with those of the Co/Al2O3 and Co/Nb2O5 catalysts. The effect of the reduction temperature on the CO hydrogenation activity and selectivity was studied, showing that interaction of cobalt and niobia surface species favored the selectivity for hydrocarbon chain growth. However, this effect is less pronounced on the niobia-promoted Co/Al2O3 compared to Co/Nb2O5 catalysts. X-ray photoelectron spectroscopy (XPS) and diffuse reflectance spectroscopy (DRS) results on Co/x%Nb2O5/Al2O3 showed prevailing amounts of Co2+ and Co3+ after calcination and reduction at 573 K, while, after reduction at 773 K, besides metallic cobalt, the Co2+ species still remains in contact with alumina, even for higher niobia loading. It seems that during this process formation and destruction of new interfaces involving Co0-NbOx sites takes place. Results suggest that Co0, Co0-Co2+, and Co0-NbOx are the active sites at the surface. The relative abundance of Co2+ species affects greatly the performance of the catalysts. DRIFTS and selectivity results suggest that these sites might be responsible for the reaction chain growth and therefore for the drastic change in the selectivity of CH4 and C5+ hydrocarbons mainly on the Co/Nb2O5 catalyst. DRIFTS results on Co/Nb2O5/Al2O3 showed the formation of -C=C- and -CH3- besides CHxO species. With increasing reduction temperature, the -C=C- species disappear while -CH3- fragments increased markedly, suggesting the formation of increasing amounts of hydrocarbons with higher chain length.     

A zirconium modified Co/SiO2 Fischer-Tropsch catalyst prepared by dielectric-barrier discharge plasma

Co/SiO₂ and zirconium promoted Co/Zr/SiO₂ catalysts were prepared using dielectric-barrier discharge (DBD) plasma instead of the conventional thermal calcination method. Fischer-Tropsch Synthesis (FTS) performances of the catalyst were evaluated in a fixed bed reactor. The results indicated that the catalyst treated by DBD plasma shows the higher FTS activity and yield of heavy hydrocarbons as compared with that treated by the conventional thermal calcination method. Increase in CO conversion was unnoticeable on the Co/SiO₂ catalyst, but significant on the Co/Zr/SiO₂ catalyst, both prepared by DBD plasma. On the other hand, heavy hydrocarbon selectivity and chain growth probability (α value) were enhanced on all the catalysts prepared by the DBD plasma. In order to study the effect of the DBD plasma treatment on the FTS performance, the catalysts were characterized by N₂-physisorption, H₂-temperature programed reduction (H₂-TPR), H₂-temperature-programmed desorption (H₂-TPD) and oxygen titration, transmission electron microscope (TEM) and X-ray diffraction (XRD). It was proved that, compared with the traditional calcination method, DBD plasma not only could shorten the precursor decomposition time, but also could achieve better cobalt dispersion, smaller Co₃O₄ cluster size and more uniform cobalt distribution. However, cobalt reducibility was hindered to some extent in the Co/SiO₂ catalyst prepared by DBD plasma, while the zirconium additive prevented significantly the decrease in cobalt reducibility and increased cobalt dispersion as well as the FTS performance.     

Catalytic methanation reaction over alumina supported cobalt oxide doped noble metal oxides for the purification of simulated natural gas

A series of alumina supported cobalt oxide based catalysts doped with noble metals such as ruthenium and platinum were prepared by wet impregnation method.The variables studied were difference ratio and calcination temperatures.Pt/Co(10∶90)/Al2O3 catalyst calcined at 700 ℃ was found to be the best catalyst which able to convert 70.10% of CO2 into methane with 47% of CH4 formation at maximum temperature studied of 400 ℃.X-ray diffraction analysis showed that this catalyst possessed the active site Co3O4 in face-centered cubic and PtO2 in the orthorhombic phase with Al2O3 existed in the cubic phase.According to the FESEM micrographs,both fresh and spent Pt/Co(10∶90)/Al2O3 catalysts displayed small particle size with undefined shape.Nitrogen Adsorption analysis showed that 5.50% reduction of the total surface area for the spent Pt/Co(10∶90)/Al2O3 catalyst.Meanwhile,Energy Dispersive X-ray analysis(EDX) indicated that Co and Pt were reduced by 0.74% and 0.14% respectively on the spent Pt/Co(10∶90)/Al2O3catalyst.Characterization using FT-IR and TGA-DTA analysis revealed the existence of residual nitrate and hydroxyl compounds on the Pt/Co(10∶90)/Al2O3 catalyst.