镧掺杂硫酸钛的酸性及催化缩酮活性

以La2O3为镧源,硫酸钛掺杂镧后经高温焙烧制得一类稀土改性固体酸.用DTA,XRD表征催化剂结构,用吸附吡啶的FT-IR表征其表面酸性,由Hammett指示剂来测定酸强度,以正丁胺定量分析催化剂表面Bronsted酸和Lewis酸酸量;用环己酮与乙二醇缩酮化反应表征其酸催化性能.结果表明:催化剂表面同时存在B酸和L酸中心,且B/L酸量比与焙烧温度、镧的含量呈现较好的线性关系;在缩酮化反应中具有良好的催化活性,在300～600℃的实验范围内,催化活性随灼烧温度的升高而降低,随镧含量的增加而升高,兼有B酸和L酸的催化剂具有更好的催化活性.催化剂易回收和再生,反应后处理简单,无废酸排放,可重复使用多次,该固体酸是一种环境友好催化剂.     

还原温度对Ir/ZrO_2催化剂上巴豆醛选择性加氢的影响

采用浸渍法制备了负载型Ir/ZrO2催化剂,详细考察了H2还原温度对Ir/ZrO2催化剂上气相巴豆醛选择性加氢反应性能的影响.结果表明,随着还原温度的升高,Ir/ZrO2催化剂上巴豆醛转化率和巴豆醇选择性均先升后降.400°C下还原时,Ir/ZrO2催化剂性能最佳,巴豆醛转化率和巴豆醇选择性分别达32.2%和74.3%.X射线光电子能谱结果表明,催化剂表面系Ir0和Ir3+共存,且随着还原温度的升高,Ir0的比例逐渐增加,至600oC时,表面Ir物种大部分以Ir0存在.NH3程序升温脱附结果表明,随着还原温度的升高,催化剂表面Lewis酸中心的数目减少,强度下降.这是由于催化剂中Cl含量下降所致.Ir0和Ir3+共存和中等强度的表面Lewis酸中心有利于提高巴豆醇选择性.     

Na对PtSn/ZSM-5催化丙烷脱氢反应性能的影响

以HZSM-5分子筛为载体, 利用分步浸渍法制得不同Na含量的PtSnNa/ZSM-5催化剂, 用于丙烷脱氢反应. 利用XRD、吡啶吸附红外光谱、NH3-TPD、氢化学吸附、TPR等手段, 研究了Na的添加对PtSn/ZSM-5催化剂物化性质的影响. 结果表明: Na的添加对PtSn/ZSM-5催化剂的反应性能影响明显. 适量Na的添加不仅降低了催化剂中的Brönsted酸中心和Lewis中强/强酸中心, 抑制了积碳的发生, 提高了催化反应的稳定性; 而且提高了催化剂表面的Pt金属裸露度, 增加了反应活性. 当Na含量为1.0%(w)时, 催化剂的丙烯选择性和收率达到最大, 反应30 h后, 丙烷转化率仍然保持很高(36.4%). 继续增加Na含量, 催化剂中的Lewis弱酸中心有所增加, 同时Sn组分易于被还原成Sn0, 丙烷裂解、氢解等副反应增加, 不利于脱氢反应的进行.     

γ-Al2O3改性对AlCl3/γ-Al2O3催化剂性能的影响

采用HCl和NaOH改性γ-Al2O3载体制备AlCl3/γ-Al2O3固载催化剂,用吡啶-FTIR和吡啶-TPD技术分析了催化剂的表面酸性(酸中心类型、酸强度和酸量),并以1-癸烯齐聚作为探针反应,研究了催化剂的稳定性以及催化剂对聚合反应的影响.结果表明,催化剂含有两种酸类型,即Lewis酸和Br(o)nsted酸,与未改性的催化剂相比,氢氧化钠改性载体制备的催化剂,酸量增大了47％,催化剂催化1-癸烯的齐聚反应活性增加了11.4％;而经盐酸改性制备的催化剂酸量增大112％,催化剂的活性增加了33.6％.酸强度依AlCl3/γ-Al2O3,AlCl3/γ-Al2O3(NaOH),AlCl3/γ-Al2O3 (HCl)的顺序增强.     

复合型油品加氢精制催化剂载体的研制

研究了复合型油品加氢精制催化剂载体的制备及表征方法.通过在粗孔硅胶的表面担载二氧化钛,利用二氧化硅稳定的骨架结构及二氧化钛金属载体之间强的相互作用制备新型的催化剂载体.采用吡啶吸附的红外光谱法测定催化剂载体的B、L酸,等温氮吸附测定载体的表面积、孔径、孔容物性参数,原子吸收光谱测定载体表面担载的钛元素含量和载体表面的杂质.采用多次浸渍的方法来达到控制钛担载量.在担载了活性组分Co、Mo之后,;用脉冲微反-色谱装置,评价了催化剂对噻吩的加氢脱硫活性.     

掺杂La2O3的硫酸钛在缩醛(酮)反应中的催化活性

硫酸钛掺杂La2O3后经高温焙烧制得一种新型固体酸催化剂。用环己酮缩乙二醇反应表征其催化活性的反应条件为：环己酮200mmol,n(环己酮)：n(乙二醇)=1．0：1．5,带水剂环己烷15mL,硫酸钛催化剂[w(La2O3)0．05,400℃焙烧3h]用量4．1％(以环己酮质量计),回流分水1h,收率94．5％。结果表明,催化活性随La2O3含量的增加而升高,随焙烧温度的升高而降低。催化剂吸附吡啶的红外光谱证实催化剂表面存在明显的Broensted酸中心和Lewis酸中心。该催化剂对其它缩醛(酮)反应也有催化活性。     

γ-A1_2O_3改性对AlCl_3/γ-Al_2O_3催化剂性能的影响（英文）

采用HCl和NaOH改性γ-A12O3载体制备AlCl3/γ-A12O3固载催化剂,用吡啶-FTIR和吡啶-TPD技术分析了催化剂的表面酸性(酸中心类型、酸强度和酸量),并以1-癸烯齐聚作为探针反应,研究了催化剂的稳定性以及催化剂对聚合反应的影响.结果表明,催化剂含有两种酸类型,即Lewis酸和Brnsted酸,与未改性的催化剂相比,氢氧化钠改性载体制备的催化剂,酸量增大了47%,催化剂催化1-癸烯的齐聚反应活性增加了11.4%;而经盐酸改性制备的催化剂酸量增大112%,催化剂的活性增加了33.6%.酸强度依AlC l3/γ-A12O3,AlC l3/γ-Al2O3(NaO H),AlC l3/γ-Al2O3(HCl)的顺序增强.     

Fe/Ti-PILC用于C_3H_6选择性催化还原NO的研究

采用二氧化钛对蒙脱土进行柱撑改性后,以离子交换法制备了铁负载二氧化钛柱撑蒙脱土催化剂Fe/Ti-PILC,考察了其在富氧条件下催化C_3H_6选择性还原NO(C_3H_6-SCR)的性能。并借助N_2等温吸附-脱附、XRD、UV-vis、H_2-TPR、Py-FTIR等表征方法研究了催化剂的结构与性能之间的关系。结果表明,所制备的19Fe/Ti-PILC催化剂在400℃时即可实现到NO的完全脱除,N2选择性能够达到90%以上。且具有较好的抗水蒸气和抗SO_2的能力。N_2吸附-脱附和XRD结果显示,蒙脱土的结构被撑开,交联柱撑有效,形成了较大的比表面积和孔体积。UV-vis结果表明,催化剂的脱硝活性与铁氧低聚物种FexOy的含量有关,Py-FTIR结果表明,催化剂表面同时存在Lewis酸和Brnsted酸,Fe~(3+)负载到柱撑黏土中能够显著增加Lewis酸的含量,Lewis酸是影响催化剂脱硝活性的影响因素之一。H_2-TPR表征表明,催化剂在400℃左右有较强的还原能力,催化剂的还原能力主要体现为Fe~(3+)→Fe~(2+)的还原。     

氧化钽及钽钨复合氧化物固体酸催化己糖脱水制备5-羟甲基糠醛以及非等计量比的甲酸和乙酰丙酸（英文）

5-羟甲基糠醛(HMF)是最具应用前景的平台化合物之一, HMF制备的研究越来越成为热点,并且已经取得了令人瞩目的研究成果.尽管如此,在现阶段利用固体酸催化剂催化碳水化合物制备HMF的研究仍然面临许多挑战,以葡萄糖为原料制备HMF时产物选择性普遍较低.因此,合成制备高活性催化糖类化合物脱水制HMF的固体酸催化剂,并且研究固体酸催化剂表面酸性质比如酸密度、酸强度以及Br?nsted/Lewis酸比值等对糖类化合物制HMF反应中各反应产物选择性的影响,对新型高效催化剂的开发设计具有重要意义.本文通过溶剂挥发自组装法合成了一系列介孔Ta及Ta-W氧化物固体酸催化剂,并用于催化果糖和葡萄糖脱水制备5-羟甲基糠醛.以三甲基膦(TMP)为探针分子,利用31P固体核磁共振谱技术表征催化剂表面酸性质,考察复合金属氧化物固体酸催化剂酸量、酸强度以及酸类型对催化果糖和葡萄糖制备HMF反应性能的影响,为高效催化剂的设计提供一定的理论指导.另外,我们还通过引入2-丁醇构建有机溶剂/水体系,考察有机溶剂对葡萄糖脱水制HMF反应中所用催化剂活性和产物选择性的影响.31P固体核磁共振技术表征样品的酸性质发现,随着W掺杂量的增加,系列Ta及Ta-W氧化物的酸强度和Br?nsted/Lewis酸量比值逐渐增加.催化反应结果表明,以介孔Ta及Ta-W复合氧化物为催化剂时,果糖和葡萄糖脱水制HMF反应的催化活性和HMF选择性与所用催化剂的酸量、酸类型和酸强度有关.介孔Ta及Ta-W复合氧化物催化剂表面的B/L比值越高,催化反应过程中的己糖转化率也越高, HMF选择性也普遍越高.具有较高Br?nsted酸强度的催化剂在水溶液中更易降低HMF产物选择性,归结于HMF的再水解和葡萄糖的非选择性脱水等副反应.实验结果发现,产物甲酸(FA)的选择性远高于乙酰丙酸(LA),说明过量FA很可能来自果糖在Lewis酸位上的分解.2-丁醇的引入能够提高己糖转化率和HMF选择性,并且在B/L比值越高的催化剂上提升的效果越显著.其中, Ta_7W_3氧化物为催化剂时, HMF选择性最高可达54%,并且该催化剂具有良好的催化稳定性,这主要是因为2-丁醇的加入能够有效地抑制反应中胡敏素等聚合物的生成,防止后者在催化剂表面附着导致催化活性降低,进而提高了催化剂在催化反应中的稳定性.     

氮氧双功能salen催化剂在酮的不对称硅氰化反应中的应用

通过在催化剂的不同位置同时引入LALB（Lewis acid/Lewis base）双功能基团（包括氮氧偶极基团和金属钛中心）来改善其催化活性和立体控制能力,合成基于salen骨架结构的新型氮氧双功能催化剂.在相对温和的条件下成功的将该类双功能催化剂应用于酮的不对称硅氰化反应,表现出了中等程度的选择性和非常高的反应活性...     

Preparation and Acid Catalytic Activity of TiO2 Grafted Silica MCM-41 with Sulfate Treatment

TiO2 grafted silica MCM-41 catalyst with and without sulfate treatment were prepared. The structural and acid properties of these materials were investigated by XRD, N2 adsorption-desorption, element analysis, thermal analysis, Raman and FTIR measurements. Their acid-catalytic activities were evaluated using the cyclization reaction of pseudoionone. It was found that the obtained materials possess well-ordered mesostructure, and the grafted TiO2 components were in highly dispersed amorphous form. T/MCM41 without sulfation contained only Lewis acid sites, while Br?nsted and Lewis acidities were remarkably improved for the sulfated materials ST/MCM41 and d-ST/MCM41. T/MCM-41 was not active for the cyclization reaction of pseudoionone, but ST/MCM-41 and d-ST/MCM-41 possessed favorable catalytic activities. The catalytic performance of ST/MCM-41 was comparable with that of the commercial solid acid catalyst of Amberlyst-15, and better than that of d-ST/MCM-41, although the latter underwent a second TiO2 grafting process and accordingly had higher Ti and S content. The specific surface structure of Si-O-Ti-O-S=O in ST/MCM-41 and the bilateral induction effect of Si and S=O on Si-O-Ti bonds were speculated to account for its higher acid catalytic activity.     

Precise Size Control over Ultrafine Rutile Titania Nanocrystallites in Hierarchical Nanotubular Silica/Titania Hybrids with Efficient Photocatalytic Activity

Hierarchical‐structured nanotubular silica/titania hybrids incorporated with particle‐size‐controllable ultrafine rutile titania nanocrystallites were realized by deposition of ultrathin titania sandwiched silica gel films onto each nanofiber of natural cellulose substances (e.g., common commercial filter paper) and subsequent flame burning in air. The rapid flame burning transforms the initially amorphous titania into rutile phase titania, and the silica gel films suppress the crystallite growth of rutile titania, thereby achieving nano‐precise size regulation of ultrafine rutile titania nanocrystallites densely embedded in the silica films of the nanotubes. The average diameters of these nanocrystallites are adjustable in a range of approximately 3.3–16.0 nm by a crystallite size increment rate of about 2.4 nm per titania deposition cycle. The silica films transfer the electrons activated by crystalline titania and generate catalytic reactive species at the outer surface. The size‐tuned ultrafine rutile titania nanocrystallites distributed in the unique hierarchical networks significantly improve the photocatalytic performance of the rutile phase titania, thereby enabling a highly efficient photocatalytic degradation of the methylene blue dye under ultraviolet light irradiation, which is even superior to the pure anatase‐titania‐based materials. The facile stepwise size control of the rutile titania crystallites described here opens an effective pathway for the design and preparation of fine‐nanostructured rutile phase titania materials to explore potential applications.     

SO42-/TiO2-SiO2 mixed oxide catalyst, 3. An eco-friendly catalyst for esterification of acetic acid

The effect of addition of titania to silica was examined by various characterization techniques such as FT-IR, BET surface area, surface acid strength/acid sites by the Hammett indicator method and Br?nsted/Lewis acid sites by pyridine adsorbed IR study. Ti-O-Si bond is formed in case of TiO₂-SiO₂ sample, as observed from FT-IR data. Acid strength, surface acid sites, and rate constant for esterification of acetic acid are increased with Ti-O-Si bonding and sulfate impregnation. Both Br?nsted and Lewis acid sites are responsible for catalysing the esterification reaction. This revised version was published online in August 2006 with corrections to the Cover Date.     

Titania on Silica. A Comparison of Sol-Gel Routes and Traditional Methods

Titania on silica samples have been prepared by: i) precipitation-deposition from a solution of TiCl₃ onto the surface of a commercial silica, and ii) base catalysed hydrolysis-condensation of TEOS followed by reaction with Ti isopropoxide. These samples were characterised by nitrogen and hydrogen adsorption, X-ray diffraction, FTIR, temperature programmed reduction, transmission electron microscopy and catalytic activity in butane-hydrogen conversion. The sol-gel preparation produced a better titania dispersion due to the formation of stabilising Ti-O-Si bonds. Upon these samples was then introduced Ir. Strong metal-support interactions between Ir and titania have been observed after high temperature reduction, causing a significantincrease in butane dehydrogenation activity relative to hydrogenolysis.It appears that using sol-gel chemistry useful supports for catalytic metals containing Si-O-Ti linkages can be produced and in future may be optimised for other metal-oxygen metal pairs.     

Influence of phosphate modification on the surface properties of sulfated titania

The effect of increasing phosphate loading on the bulk and surface properties of sulfated titania was investigated by thermogravimetry, X-ray diffraction, laser Raman spectroscopy and FT-IR spectroscopy. The acid properties of the material were probed by low-temperature FT-IR spectroscopy of adsorbed CO. Monophosphate species in varying symmetries and protonation states were detected on the surface of the sulfated titania at low loadings. These condensed with formation of surface polyphosphates with increasing loading. Phosphate blocks weak Lewis acid sites and partially displaces sulfate groups. While the acid, properties of phosphate-free sulfated titania are dominated by Lewis acid sites, the phosphated samples also developed Brønsted acid sites due to the presence of POH groups on the surface.     

在杂多酸催化剂上苯和1-十二烯烷基化合成十二烷基苯

对不同ＳｉＯ２负载磷钨酸（ＰＷ）催化剂的表面性质、热稳定性、酸性、以及对苯与丙烯和１－十二烯的烷基化反应的催化活性进行了对比研究,结果表明,ＰＷ在ＳｉＯ２上的分散状况与ＳｉＯ２的比表面积和孔径大小有关,ＰＷ与载体表面作用的强弱会直接影响负载型催化剂的热性和酸性,采用不同的ＳｉＯ２可以制得比表面积、孔结构和酸强度不同的负载型ＰＷ催化剂,以满足不同催化反应的要求。     

Characterization of Fumed Alumina/Silica/Titania in the Gas Phase and in Aqueous Suspension

Fumed oxide alumina/silica/titania was studied in comparison with fumed alumina, silica, titania, alumina/silica, and titania/silica by means of XRD, ¹H NMR, IR, optical, dielectric relaxation, and photon correlation spectroscopies, electrophoresis, and quantum chemical methods. The explored Al₂O₃/SiO₂/TiO₂ consists of amorphous alumina (22 wt%), amorphous silica (28 wt%), and crystalline titania (50 wt%, with a blend of anatase (88%) and rutile (12%)) and has a wide assortment of Brønsted and Lewis acid sites, which provide a greater acidity than that of individual fumed alumina, silica, or titania and an acidity close to that of fumed alumina/silica or titania/silica. The changes in the Gibbs free energy (ΔG) of interfacial water in an aqueous suspension of Al₂O₃/SiO₂/TiO₂ are close to the ΔG values of the dispersions of pure rutile but markedly lower than those of alumina, anatase, or rutile covered by alumina and silica. The zeta potential of Al₂O₃/SiO₂/TiO₂ (pH of the isoelectric point (IEP) equals ≈3.3) is akin to that of fumed titania (pH(IEP_TiO2) ≈ 6) at pH > 6, but it significantly differs from the ζ of fumed alumina (pH(IEP_Al2O3) ≈ 9.8) at any pH value as well as those of fumed silica, titania/silica, and alumina/silica at pH < 6. The particle size distribution in the diluted aqueous suspensions of Al₂O₃/SiO₂/TiO₂ studied by means of photon correlation spectroscopy depends relatively slightly on pH in contrast to the titania/silica or alumina/silica dispersions. Theoretical calculations of oxide cluster interaction with water show a high probability of hydrolysis of Al–O–Ti and Si–O–Ti bonds strained at the interface of alumina/titania or silica/titania due to structural differences in the lattices of the corresponding individual oxides. Ab initio calculated chemical shift δ_H values of H atoms in different hydroxyl groups at the oxide clusters and in bound water molecules are in agreement with the ¹H NMR data and show a significant impact of charged particles (H₃O⁺ or OH⁻) on the average δ_H values of water droplets with (H₂O)_n at n between 2 and 48.     

The role of macroligands in regioselective hydrogenation of cinnamaldehyde

Summary Attention has been paid to the role of a macroligand in the regioselective catalytic hydrogenation of cinnamaldehyde. The macroligands tested were of ordered, regular structures and also served as catalytic supports (natural graphite, plankton based silica, latex templated titania). The active part - ruthenium - was, besides the macroligands, supported also on active charcoal and high surface area sol-gel prepared silica and titania.     

Catalytic activity during copolymerization of ethylene and 1-hexene via mixed TiO2/SiO2-supported MAO with rac-Et[Ind]2ZrCl2 metallocene catalyst

Activities during ethylene/1-hexene copolymerization were found to increase using the mixed titania/silica-supported MAO with rac-Et[Ind]2ZrCl2 metallocene catalyst. Energy Dispersive X-ray spectorcopy (EDX) indicated that the titania was apparently located on the outer surface of silica and acted as a spacer to anchor MAO to the silica surface. IR spectra revealed the Si-O-Ti stretching at 980 cm(-1) with low content of titania. The presence of anchored titania resulted in less steric hindrance and less interaction due to supporting effect.     

Optical Trapping of Titania/Silica Core-Shell Colloidal Particles

Manipulation of colloidal systems via optical trapping techniques requires a refractive index mismatch between particles and solvent which leads to strong interparticle van der Waals interactions. Investigation of the behavior of systems without such strong attractive interactions, however, requires the uncoupling of particle refractive index and particle-particle interactions. To accomplish this, the synthesis of core-shell titania/silica particles has been performed. By index matching a silica shell on a titania core using a mixture of toluene and propanol, the van der Waals interactions between particles can be minimized. Due to the mismatch of the refractive index between the solvent and titania core, however, a strong trapping force can be generated, making optical manipulation feasible. In order to confirm that the silica shell was indeed matched, pure silica particles were synthesized by the method of St?ber (1968) and added to the core-shell system. In these mixed systems of core-shell and pure silica particles in silica-index-matching solvents, only the core-shell particles were trappable. Copyright 2000 Academic Press.