自动电位滴定法快速测定钾盐中的钾含量

钾含量的测量常用火焰光度法和四苯硼钾重量法。火焰光度法适用于微量分析 ,对较高含量钾的测定误差较大 ,四苯硼钾重量法的测定准确度高 ,但操作繁琐 ,测定周期长 ,易出错。本文采用四苯硼钠溶液电位滴定法 ,测定高、中含量组分钾 ,测定周期短 ,所用试剂少 ,且不受样品中水不溶物的干扰 ,选择性好 ,测定的准确度和精密度均在 0 .2 %以下 ,适用于钾盐、卤水、复合肥和钾肥中钾的测定。1　实验部分1 .1　仪器和药品ZD 2型自动电位滴定仪 (上海雷磁仪器厂 ) ,PK 1型钾离子选择电极 ,2 1 7型饱和甘汞电极 (双盐桥 )。四苯硼钠标准液 :0 .1mol…     

基于多壁碳纳米管/纳米银复合修饰剂电致化学发光传感器的制备及应用

建立了基于多壁碳纳米管(MWNT)/纳米银(nano-Ag)复合修饰剂固载联吡啶钌(Ru(bpy)_3~(2+))传感器测定盐酸苯海索的电致化学发光分析方法。借助MWNT优良导电性及nano-Ag的电催化性能,采用溶胶-凝胶法,利用成膜剂硅溶胶(Silica sol)、聚乙烯醇(PVA)将MWNT、nano-Ag、Ru(bpy)_3~(2+)固载修饰到热解石墨电极(PGE)表面,制备出MWNT/nano-Ag/Silica sol/PVA/Ru(bpy)_3~(2+)-PGE电致化学发光传感器,并依据盐酸苯海索对联吡啶钌的增敏作用,快速、准确测定了盐酸苯海索。结果表明:盐酸苯海索在4. 36×10~(-7)～1. 09×10~(-4)mol·L~(-1)浓度范围内与其发光强度线性关系良好,线性方程为I_(ECL)=146. 98×10~5c+502. 03(r~2=0. 997 3),检出限(S/N=3)为2. 06×10~(-8)mol·L~(-1);对5份不同加标浓度的盐酸苯海索的回收率为97. 7%～104%,相对标准偏差(RSD)为2. 4%。该方法对检测盐酸苯海索药品具有良好的灵敏度与稳定性,效果满意。     

间接原子发射光谱法测定碘解磷定

研究了等离子发射光谱法间接测定碘解磷定。在pH5．0的溶液中，当四苯硼钠过量时可完全沉淀碘解磷定，在滤液中加入过量的氯化钾沉淀剩余的四苯硼钠，再测定滤液中过量的钾，可以计算得到碘解磷定的含量。方法简单快速，回收率在96％～102％之间，相对标准偏差为1．7％。     

四苯硼钠沉淀-ICP 发射光谱法间接测定药物片剂中扑尔敏含量

研究了等离子体发射光谱法间接测定药物片剂中扑尔敏的含量。选择了沉淀条件及ＩＣＰ－ＡＥＳ测定的最佳条件。在ＰＨ２－４．５范围内,当四苯硼钠过量时可完全沉淀扑尔敏。硝酸铝可以使沉淀导速如凝而易于过滤,测定滤液中的四苯硼钠计算得扑尔敏的含量。方法的相对标准偏差为２．２％回收率为９９％－１０２％,已用于实际样品的分析。     

间接原子发射光谱法测定氢溴酸山莨菪碱

研究了电感耦合等离子体-原子发射光谱法间接测定氢溴酸山莨菪碱。在pH5．0溶液中过量四苯硼钠可使氢溴酸山莨菪碱沉淀完全，加入氯化钾沉淀滤液中剩余的四苯硼钠，测定滤液中过量的钾，可以计算得到氢溴酸山莨菪碱的含量。方法简单快速，回收率在97％～102％之间，相对标准偏差为1．3％。     

超高效液相色谱-串联质谱法测定人血浆中苯海索

建立了灵敏、高通量的超高效液相色谱-串联质谱（UPLC-MS/MS）定量测定人血浆中苯海索的方法,用于盐酸苯海索片生物等效性研究,并确证食物对苯海索体内药代动力学行为的影响。以甲醇为沉淀剂进行蛋白质沉淀,苯海索-d11为内标,采用Waters Acquity UPLC BEH C8色谱柱（50 mm×2.1mm,1.7 μm）,以0.1%（v/v）甲酸水溶液（含5 mmol/L醋酸铵）和乙腈-水（95：5,v/v）为流动相进行梯度洗脱;采用电喷雾电离（ESI）源,在正离子模式下进行多反应监测（MRM）扫描。苯海索在0.1~40 ng/mL范围内线性关系良好。应用该方法测定中国健康受试者空腹及餐后单次口服2 mg盐酸苯海索片后的血药浓度,结果显示最大血药浓度（C_max）、血药浓度-时间曲线下面积（AUC_0-t、AUC_0-∞）的90%置信区间均在80.0%~125.0%范围内,表明两种制剂在空腹和餐后均生物等效。     

原子吸收光谱法间接测定碘解磷定

研究了原子吸收光谱法间接测定碘解磷定。在pH5．0溶液中,当四苯硼钠过量时可完全沉淀碘解磷定,在滤液中加入过量的KCl沉淀剩余的四苯硼钠．再测定滤液中的过量的钾,可以计算得到碘解磷定的量。方法的回收率在98％～103％之间．相对标准偏差为1．8％。     

甲基硫酸新斯的明的ICP-AES测定

研究了电感耦合等离子体原子发射光谱法间接测定甲基硫酸新斯的明，在溶液pH为5.0，四苯硼钠过量时可完全沉淀甲基硫酸新斯的明，测定滤液中的四苯硼钠可以计算得到甲基硫酸新斯的明的含量；方法简单快速，回收率在95％-101％之间，相对标准偏差为1.8％。     

间接原子吸收光谱法测定甲基硫酸新斯的明

建立了原子吸收光谱法间接测定甲基硫酸新斯的明的方法。在pH5．0溶液中，当四苯硼钠过量时可完全沉淀甲基硫酸新斯的明，在滤液中加入过量的KCl沉淀剩余的四苯硼钠，再测定滤液中的过量的钾，可以计算得到甲基硫酸新斯的明的质量分数。方法回收率在97％～103％之间，相对标准偏差为1．5％。     

电导滴定法快速测定钾的含量

１引言测定钾的含量常用火焰光度法和四苯硼钠重量法，火焰光度法适用于微量分析，四苯硼钠重量法的测定周期长。电导滴定法用于测定一些可发生沉淀反应的离子时，具有快速简便的优点。本文采用四苯硼钠溶液滴定，电导滴定法测定高、中含量组分钾的含量，测定周期仅需１０ｍｉｎ，所用试剂量少，不受样品中水不溶物的干扰，适用于钾盐、卤水和复合肥中钾的测定。２实验部分２．１仪器和药品电导率的测定采用ＤＤＳ－１２Ａ型数字式电导率仪和２１６型电导电极。四苯硼钠（Ｎａ［Ｂ（６Ｈ５）４］）为分析纯试剂，配成水溶液后用基准ＫＣＩ标…     

On-line collection/concentration and determination of transition and rare-earth metals in water samples using Multi-Auto-Pret system coupled with inductively coupled plasma-atomic emission spectrometry

On-line preconcentration and determination of transition and rare-earth metals in water samples was performed using a Multi-Auto-Pret system coupled with inductively coupled plasma-atomic emission spectrometry (ICP-AES). The Multi-Auto-Pret AES system proposed here consists of three Auto-Pret systems with mini-columns that can be used for the preconcentration of trace metals sequentially or simultaneously, and can reduce analysis time to one-third and running cost of argon gas and labor. A newly synthesized chelating resin, ethylenediamine-N,N,N′-triacetate-type chitosan (EDTriA-type chitosan), was employed in the Multi-Auto-Pret system for the collection of trace metals prior to their measurement by ICP-AES. The proposed resin showed very good adsorption ability for transition and rare-earth metal ions without any interference from alkali and alkaline-earth metal ions in an acidic media. For the best result, pH 5 was adopted for the collection of metal ions. Only 5 mL of samples could be used for the determination of transition metals, while 20 mL of samples was necessary for the determination of rare-earth metals. Metal ions adsorbed on the resin were eluted using 1.5 M nitric acid, and were measured by ICP-AES. The proposed method was evaluated by the analysis of SLRS-4 river water reference materials for trace metals. Good agreement with certified and reference values was obtained for most of the metals examined; it indicates that the proposed method using the newly synthesized resin could be favorably used for the determination of transition and rare-earth metals in water samples by ICP-AES.     

Determination of gold in sludge and soil by sequential ICP-AES after preconcentration and separation with thiol-cotton fibre

Summary A method is presented for the determination of gold in sludge and soil samples by sequential ICP-AES after preconcentration and separation from the common alkali and alkaline-earth metals, as well as other matrix components, e.g. iron, by a thiol-cotton fibre column. The cotton fibre, impregnated with thioacetic acid, quantitatively adsorbs gold, thus eliminating the severe spectral interferences encountered by direct ICP-AES analysis. After preconcentration and separation the results obtained at Au 242.795 nm and Au 267.595 nm agree with each other. A quantitative recovery for added spikes was obtained. The method allows the determination of gold in complex matrices such as soil or sludge samples that have been proven to be impossible by conventional ICP-AES without separation from the matrix.On leave from Shanghai Institute of Metallurgy, Academia Sinica, Shanghai 2000 50, China     

Ultrasound-assisted extraction in the determination of arsenic,cadmium, copper,lead, and silver in contaminated soil samples by inductively coupled plasma atomic emission spectrometry

An extraction method was developed for the determination of toxic elements in contaminated soil samples by inductively coupled plasma atomic emission spectrometry (ICP-AES). The determination of arsenic, cadmium, lead, and silver in ultrasound-assisted extracts of SRM 2710 and SRM 2711 by ICP-AES was carried out with high accuracy and precision (RSD<3.7%). The certified concentrations of the SRMs were obtained for arsenic, cadmium, lead, and silver by using an ultrasound-assisted extraction method with a digestion solution of (1+1)-diluted aqua regia. The determination of copper in SRMs by the ultrasound-assisted extraction method and analysis by ICP-AES failed to obtain the certified concentrations at the 95% level of confidence using (+/-2 s) as confidence limits of the mean. However, the same results were observed with the use of the microwave digestion method and reflux, which is the ISO 11466 standard method. The analysis of the SRMs showed that the ultrasound-assisted extraction method is highly comparable with the other methods used for such purposes. The major advantages of the ultrasound-assisted extraction method compared to the microwave and reflux methods are the high treatment rate (50 samples simultaneously in nine minutes) and low reagent usage, the main benefit of which are the low chloride and nitrate concentrations in the extracts.     

遗传光度法用于地质样品中多组分同时测定

将遗传算法（ＧＡ）用于地质样品中１５个稀土元素同时测定,分析结果与ＩＣＰ法进行了比较,大多数组分浓度的相对误差小于１０％,个别小于１６．２％,初步验证,遗传算法可以摆脱对校准模型的依赖。文中还讨论了变异概率,交配概率,种群数大小等因素的影响。     

Comparative determination of Ba, Cu, Fe, Pb and Zn in tea leaves by slurry sampling electrothermal atomic absorption and liquid sampling inductively coupled plasma atomic emission spectrometry

The comparative determination of barium, copper, iron, lead and zinc in tea leaf samples by two atomic spectrometric techniques is reported. At first, slurry sampling electrothermal atomization atomic absorption spectrometry (ETAAS) was applied. The results of Ba and Pb determination were calculated using the method of standard additions, and results of Cu, Fe and Zn from the calibration graphs based on aqueous standards. These results were compared with the results obtained after microwave-assisted wet (nitric+hydrochloric+hydrofluoric acids) digestion in closed vessels followed by inductively coupled plasma-atomic emission spectrometric (ICP-AES) determination with the calibration by means of aqueous standards. The exception was lead determined after a wet digestion procedure by ETAAS. The accuracy of the studied methods was checked by the use of the certified reference material Tea GBW-07605. The recoveries of the analytes varied in the range from 91 to 99% for slurry sampling ETAAS, and from 92.5 to 102% for liquid sampling ICP-AES. The advantages of slurry sampling ETAAS method are simplicity of sample preparation and very good sensitivity. Slurry sampling ETAAS method is relatively fast but if several elements must be determined in one sample, the time of the whole microwave-assisted digestion procedure and ICP-AES determination will be shorter. However, worse detection limits of ICP-AES must also be taken into the consideration in a case of some analytes.     

微波灰化-电感耦合等离子体原子发射光谱法测定原油中的金属元素

采用微波灰化技术消化原油样品,并使用电感耦合等离子体原子发射光谱法(ICP-AES)测定其中Na、Mg、Ca、Fe、V、Ni和Cu的含量。探讨了原油样品中金属元素测定的称样量和微波灰化程序,并优化了仪器工作参数和实验条件。样品经微波灰化处理后,用盐酸溶解残渣,方法对Na、Mg、Ca、Fe、V、Ni和Cu元素的检出限分别为0.07、0.01、0.01、0.01、0.02、0.04和0.03mg/kg,回收率在84.5%～96.6%之间,相对标准偏差在2.1%～6.9%范围。方法简便、可靠,可用于原油中Na、Mg、Ca、Fe、V、Ni和Cu 7种金属元素的检测。     

ICP-AES法测定矿石中的BeO

报道了采用ICP－AES法测定矿石中的BeO。对试样的溶解进行了选择；考察了其体和无机酸对测定的影响。采用基体匹配法进行测定。在优化条件下，对三个试样进行测定，其相对标准偏差（n=9）为0.28%；回收率为97％－103％。     

电感耦合等离子体原子发射光谱法(ICP-AES)测定铜磁铁矿中铜、锰、铝、钙、镁、钛和磷的含量

通过样品处理、干扰实验、方法检出限、准确度和精密度实验,确定了最佳实验条件,建立了电感耦合等离子体-原子发射光谱法(ICP-AES)测定铜磁铁矿中铜、锰、铝、钙、镁、钛和磷含量的方法。试料经盐酸、硝酸、氢氟酸、高氯酸分解,用盐酸溶解盐类,过滤,采用电感耦合等离子体原子发射光谱法同时测定滤液中铜、锰、铝、钙、镁、钛和磷的含量。方法检出限为锰、钛和磷小于0.00085%,其它元素小于0.0054%,分析结果与分光光度法、X射线荧光光谱法(XRF)和原子吸收光谱法(AAS)分析结果一致,8个实验室对5个水平样品进行协同实验给出了方法的精密度。     

电感耦合等离子体原子发射全谱直读光谱仪同时测定铅基合金中的银锶钙

应用硝酸分解样品, Optima 4300DV ICP同时测定铅基合金中的Ag、Ca、Sr, 方法对Ag、Ca、Sr的检出限分别达到0.005、0.06、0.0015 mg/L.经加标回收实验及方法对比试验验证,此方法分析结果准确可靠,能满足铅基合金中Ag、Ca、Sr的测定.     

电感耦合等离子体原子发射光谱法测定烧结增效剂中三氧化二硼和二氧化锰

提出了电感耦合等离子体原子发射光谱法测定烧结增效剂中主成分三氧化二硼和二氧化锰含量的方法。用盐酸-硝酸混合溶液溶解样品,选择波长257.610,249.773 nm两条谱线分别作为测定硼和锰的分析线,采用背景校正来扣除干扰。方法用于烧结增效剂样品分析,测定结果与化学法测定值相一致。