AlMCM-48介孔分子筛的合成研究

采用正硅酸乙酯为硅源,十六烷基三甲基溴化铵作模板剂合成MCM-48介孔分子筛.用Al(NO3)3溶液浸渍MCM-48从而获得AlMCM-48.用XRD、27AlNMR对样品进行了表征.这种方法掺杂铝不破坏分子筛骨架结构,Si/Al低至5时分子筛结构保持完好.其中部分铝进入了骨架.     

负载Co介孔分子筛催化热解乙醇制备纳米碳管

以硅酸钠为原料,CTAB为模板剂,水热法合成MCM-41介孔分子筛,采用浸渍法制备负载钴的介孔分子筛(Co/MCM-41),并将其作为催化剂,CVD法热解无水乙醇制备CNTs.利用XRD、TEM、比表面积和孔径分布测定和Raman光谱等方法对所合成的介孔分子筛和纳米碳管进行了表征.结果表明:所制备的Co/MCM-41样品具有典型的MCM-41的介孔结构;当热解反应温度为750℃下所制备出的纳米碳管的品质最好.     

模板剂对全硅MCM-41介孔分子筛结构的影响

分别采用十六烷基三甲基溴化铵和十六烷基三乙基溴化铵作为模板剂,硅溶胶为硅源,用水热晶化法在碱性（NaOH）介质中合成了MCM-41介孔分子筛样品.通过XRD、N2吸附-脱附、TG-DTA、IR等测试手段对这两种样品进行了对比表征分析.考察了两种不同模板剂对其晶体结构、比表面及孔径大小的影响.实验结果表明,相对于十六烷基三甲基溴化铵做模板剂,采用大头基的十六烷基三乙基溴化铵可以合成较大孔径和孔容（分别为4.72 nm和1.14 cm3•g-1）的MCM-41介孔分子筛,而且具有较窄的孔径分布,因此对于合成大孔径的介孔分子筛MCM-41,十六烷基三乙基溴化铵是一种很好的模板剂.     

微介孔复合分子筛合成及其在汽车冷启动尾气控制中的应用

分别采用稀溶液和浓溶液双模板剂两步水热合成法,以二氧化硅微硅粉和铝酸钠为硅源和铝源,第一步获得β分子筛晶种,第二步以β分子筛晶种为结构单元组装形成兼具MCM-41分子筛和β分子筛结构特点的复合型分子筛β/M(其中β是指β分子筛,M是指MCM-41介孔分子筛).采用X射线衍射(XRD)、傅里叶变换红外(FT-IR)光谱、氮气吸附(BET)和高分辨透射电镜(HRTEM)对样品的物相结构和微观形貌进行了表征,并对复合分子筛的合成过程进行了分析.结果表明:复合分子筛β/M的形成是微孔β结构和介孔MCM-41结构的竞争生长过程,β分子筛晶种的晶化时间和晶粒度大小对β/M复合分子筛的结构有重要影响.此外,我们以甲苯为探针分子,比较研究了三类分子筛β/M、MCM-41和β的原样以及经高温水热处理后样品的吸附性能,结果表明:β/M复合分子筛的热稳定性优于介孔分子筛MCM-41,其甲苯吸附容量比MCM-41和β分子筛的高,其中以浓溶液法合成的复合分子筛吸附容量最高.     

(Dy,Mn)MCM-41介孔分子筛的合成与表征

在碱性条件下, 以十六烷基三甲基溴化铵为模板剂, Na2Si3O7为硅源, 用水热法合成了双金属介孔分子筛(Dy, Mn)MCM-41. 并用XRD, FT-IR, SEM, X射线荧光分析法、紫外漫反射等对样品进行表征. 实验结果证实所合成的产物为(Dy,Mn)MCM-41.     

非水介质中合成介孔分子筛MCM-41

首次采用十六烷基三甲基溴化铵为模板剂、正硅酸乙酯为硅源, 分别使用无机和有机弱碱, 溶剂热晶化法在非水甘油介质中合成了介孔分子筛MCM-41, 通过XRD, N₂吸附-脱附, TG-DTG, IR, SEM等测试手段对样品进行了表征分析, 结果表明在甘油体系中得到的样品具有优良的孔结构性质. 相比于氢氧化钠, 以有机弱碱(无水乙二胺、三乙胺)作为碱源, 可以得到有序性更好、结晶度高的样品, 样品具有较窄的孔径分布.     

PtSn/Al2O3/MCM-41催化剂的丙烷脱氢催化性能

用微型催化反应装置评价, 并结合X射线粉末衍射(XRD)、表面积和孔结构测试、程序升温还原(TPR)、氢化学吸附和热重分析等方法研究了负载型PtSn/γ-Al2O3, PtSn/MCM-41和PtSn/Al2O3/MCM-41催化剂的丙烷脱氢反应催化性能. 发现PtSn/Al2O3/MCM-41催化剂具有较PtSn/MCM-41催化剂高的丙烷脱氢反应活性和较PtSn/γ-Al2O3催化剂高的反应稳定性. 实验结果表明, 纯硅MCM-41载体表面的锡物种因与载体相互作用较弱故易被还原, 导致铂金属分散度和催化剂的丙烷脱氢活性较低. 用Al2O3修饰MCM-41可以增强Sn物种与Al2O3/MCM-41载体之间的相互作用, 提高PtSn/Al2O3/MCM-41催化剂铂金属分散度和丙烷脱氢催化活性. 并且, 积炭后的PtSn/Al2O3/MCM-41催化剂具有较高的铂金属表面裸露度, 故具有较高的丙烷脱氢反应稳定性. PtSn/Al2O3/MCM-41催化剂优良的丙烷脱氢催化性能可能不仅与Sn-载体Al2O3/MCM-41较强的相互作用有关, 而且与Al2O3/MCM-41载体的介孔结构有关.     

PtSn/Al2O3/MCM-41催化剂的丙烷脱氢催化性能

用微型催化反应装置评价,并结合X射线粉末衍射(XRD)、表面积和孔结构测试、程序升温还原(TPR)、氢化学吸附和热重分析等方法研究了负载型PtSn/γ-Al2O3,PtSn/MCM-41和PtSn/Al2O3/MCM-41催化剂的丙烷脱氢反应催化性能.发现PtSn/Al2O3/MCM-41催化剂具有较PtSn/MCM-41催化剂高的丙烷脱氢反应活性和较PtSn/γ-Al2O3催化剂高的反应稳定性.实验结果表明,纯硅MCM-41载体表面的锡物种因与载体相互作用较弱故易被还原,导致铂金属分散度和催化剂的丙烷脱氢活性较低.用Al2O3修饰MCM-41可以增强Sn物种与Al2O3/MCM-41载体之间的相互作用,提高PtSn/Al2O3/MCM-41催化剂铂金属分散度和丙烷脱氢催化活性.并且,积炭后的PtSn/Al2O3/MCM-41催化剂具有较高的铂金属表面裸露度,故具有较高的丙烷脱氢反应稳定性.PtSn/Al2O3/MCM-41催化剂优良的丙烷脱氢催化性能町能不仅与Sn-载体Al2O3/MCM-41较强的相互作用有关,而且与Al2O3/MCM-41载体的介孔结构有关.     

MCM-41中孔分子筛净化含Cr(Ⅵ)废水的实验研究

以十六烷基三甲基溴化铵为模板剂,水玻璃为硅源合成中孔分子筛MCM-41,用X射线粉晶衍射、N2吸附-脱附、透射电镜分析等手段对样品进行了表征。以MCM-41处理含铬废水,在pH值为6～6.8,Cr(VI)初始浓度为10mg/g,可使水中Cr(VI)的去除率达92.70%,饱和吸附量为86.56mg/g,符合Langmuir型吸附等温式。     

Co掺杂ZnO/MCM-41分子筛的制备及对异戊醇的催化氧化性能

以Co掺杂的介孔分子筛MCM-41为载体, 采用等体积浸渍法制备了系列5%ZnO/xCo-MCM-41催化剂, 并用于催化分子氧氧化异戊醇合成异戊醛的反应. 通过X射线衍射(XRD), 傅里叶变换红外光谱(FTIR), 紫外-可见漫反射光谱(UV-Vis DRS), 扫描电子显微镜(SEM), 氨气程序升温脱附(NH₃-TPD), 氢气程序升温还原(H₂-TPR)和氮气吸附-脱附等手段对样品进行表征, 并考察了Co掺杂量对分子筛结构和催化性能的影响. 结果表明, 随着Co掺杂量的增大, 样品的比表面积和孔体积均减小, 而其平均孔径呈先增大后减小的趋势. 当Co掺杂量为0.05时, 5%ZnO/0.05Co-MCM-41仍保持了MCM-41高度有序的六方介孔结构, 具有高比表面积(989 m²/g)、较大孔径(2.88 nm)和孔体积(0.88 cm³/g), 引入的Co主要以孤立态钴离子[Single-site Co(Ⅱ)]形式存在于MCM-41骨架, MCM-41骨架中的Co可以有效提高ZnO微粒的分散度, 适度降低5%ZnO/MCM-41的表面酸性, 并大幅度提高5%ZnO/MCM-41的氧化还原性. 与5%ZnO/MCM-41相比, 5%ZnO/0.05Co-MCM-41可使异戊醛的选择性提高28.3%.     

高骨架铝含量Al-MCM-41的合成

制备了不同Al含量的Al-MCM-41试样，其中Si/Al比值最小为3，即最高含铝量x~A~l=0.303。X射线粉末衍射(XRD)分析表明样品具有MCM-41的特征结构，氮气吸附研究表明，样品呈现Ⅳ型吸附等温线，具有孔径分布均一的中孔结构。文中还利用^2^7AlMASNMR研究了试样中Al的化学环境，结果表明，即使在高铝含量的情况下，样品中的铝原子仍以四配位结合在MCM-41的硅骨架上，未能检测出骨架外六配位铝的存在。文中还就Al含量对孔结构的影响以及Al-MCM-41形成机理作了讨论。     

AlMCM-41介孔分子筛的合成及表征

以拟薄水铝石为铝源、水玻璃为硅源、十六烷基三甲基溴化铵为模板剂,在110℃时水热晶化合成了含Al的MCM-41介孔分子筛.采用X射线衍射(XRD)、N2吸附-脱附、固体29Si、27Al魔角旋转核磁共振技术(MASNMR)、扫描电镜(SEM)及吡啶吸附傅里叶变换红外(FTIR)光谱技术对AlMCM-41分子筛进行了表征.结果表明:AlMCM-41分子筛具有六方排列的孔道结构,同时具有很高的相对结晶度、比表面积和孔容,且孔分布单一;AlMCM-41分子筛中Si原子在骨架内键合的程度更高,使AlMCM-41分子筛具有更好的骨架晶化程度;同时具有四配位骨架铝,使AlMCM-41介孔分子筛具有适当的酸性.     

Effect of hydrothermal treatment on the structure, stability and acidity of Al containing MCM-41 and MCM-48 synthesised at room temperature

The effect of hydrothermal treatment of the synthesis gel on the structure, hydrothermal and mechanical stabilities and acidity of MCM-41 and MCM-48 aluminosilicates synthesised at room temperature has been investigated by X-ray diffraction, nitrogen adsorption at 77 K and DRIFTS with pyridine as probe molecule. The influence of the Al content and pore size on the structure of the resulting treated Al-MCM-41 materials has also been studied. For all samples improvement of the structural ordering and increase of the pore size, was observed, with pore wall thickness remaining practically unchanged. For Al-MCM-48 an improvement of the pore size uniformity occurs during the treatment. Only a small loss of pore size uniformity occurred for Al-MCM-41 prepared with hexadecyltrimethylammonium bromide, but with samples prepared with tetra and octadecyltrimethylammonium bromide the treatment generated a bimodal pore size distribution. The pore volume increased (17%) in the case of Al-MCM-48 but decreased (5.5–14%) for Al-MCM-41, suggesting a decrease in surface roughness resulting from increase of the degree of condensation of the pore walls. Both treated and untreated samples presented relatively strong Brønsted sites and increase of the Lewis acidity was found to occur upon treatment. Treated samples were found to be more resistant to refluxing in boiling water and mechanical compaction, which was attributed to more polymerised pore walls, with Al-MCM-41 samples tested demonstrating higher stability than Al-MCM-48. However, the differences in stability of samples prepared with or without hydrothermal treatment were not significant. Both treated and untreated samples presented high hydrothermal stability. Although refluxing in boiling water lead to some loss of structural ordering, only a small decrease of pore volume (3–5.5% for Al-MCM-41 and 8-14% for Al-MCM-48) occurred, with practically no alterations in pore size and wall thickness. Ordered mesopore structure, with narrower pores and thicker walls, was still observed after compression at 590 MPa for most of the samples tested.     

Benzene Adsorption Isotherms on MCM-41 and their Use for Pore Size Analysis

This work is focused on the elaboration of methodology for adsorption characterization of porous silicas by using benzene adsorption isotherms measured on good quality MCM-41 materials. Three MCM-41 samples were synthesized by using tetraethyl orthosilicate (TEOS) as silica source and surfactants, octyltrimethylammonium (C8), decyltrimethylammonium (C10) and cetyltrimethylammonium (C16) bromides as templates. A characteristic feature of this synthesis was relatively long hydrothermal treatment (5 days) at 373 K, which gave well ordered samples as evidenced by powder XRD analysis. Benzene adsorption isotherms measured on these MCM-41 samples were used to evaluate such standard quantities as the BET specific surface area, total pore volume, external surface area and the volume of ordered mesopores, and to obtain the statistical film thickness (t-curve) as well as the Kelvin-type relation, which describes the dependence between pore width and condensation pressure for benzene on silica at 298 K. The latter relations were incorporated into the Barrett-Joyner-Halenda algorithm to extend its applicability to calculate the pore size distributions from benzene adsorption data.     

The Synthesis and Characteristics of Vanadoaluminosilicate MCM-41 Mesoporous Molecular Sieves

A series of vanadoaluminosilicate MCM-41 mesoporous molecular sieves with various compositions have been hydrothermally synthesized. Hexadecyltrimethylammonium bromide was used as a surfactant in the synthesis. The samples were characterized with nitrogen sorption, X-ray diffraction, differential thermal analysis, thermogravimetric analysis, Fourier transform-Infrared spectroscopy, UV-visible spectroscopy, scanning electron microscopy, transmission electron microscopy, and solid state NMR. The solid products had the MCM-41 structure and contained only atomically dispersed vanadium and aluminum consistent with framework vanadium and aluminum. The samples were hydrophobic and contained large amount of surfactant in the as-synthesized samples. The surfactant could be removed upon calcination at 450°C. N₂ sorption measurements and TEM demonstrate the high mesoporosity of [V, Al]-MCM-41. The incorporation of vanadium and aluminum into MCM-41 decreased the surface area to some extent. The morphologies of all the samples were the agglomerate of plates. ²⁹Si MAS NMR shows that the pore wall is amorphous. ²⁷Al MAS NMR shows that all of aluminum species were tetrahedrally coordinated even after calcination at 550°C.     

中孔硅酸盐材料MCM-41的合成与表征研究(英文)

以十六烷基三甲基溴化铵为模板剂,硅酸钠为硅源,铝酸钠为铝源,在水热条件下成功地合成出了ＭＣＭ－４１中孔硅酸盐材料。采用ＸＲＤ、低温Ｎ２吸附脱附等测试手段对合成的ＭＣＭ－４１样品进行了表征。通过优化合成条件,合成出孔径３.２ ｎｍ、比表面９０４ｍ２／ｇ和孔壁厚约１.４６ ｎｍ的ＭＣＭ－４１分子筛。催化活性测定采用微反应活性实验来评价其活性和选择性。     

辅助有机胺对介孔分子筛MCM-41合成及其性质的影响

采用阳离子表面活性剂十六烷基三甲基溴化铵为模板剂、硫酸铝为铝源、硅溶胶为硅源，分别使用中等链长的有机胺和正己烷作为辅助添加剂，用水热晶化法在碱性介质中合成了介孔分子筛MCM-41，通过XRD、N2吸附-脱附、SEM测试手段对得到的样品进行了对比表征分析。实验结果表明，除三乙胺外，向反应体系中加入适量的三正丙胺、三正丁基胺、三正辛胺和二异丁胺后，均能够使介孔 MCM-41的d100值和孔径增大，且具有较大的BET表面积（>1 000 m2/g）和孔容（>1 cm3/g）；加入正己烷后，也可以使得MCM-41孔径变大，但是和加入有机胺相比较，合成的样品具有较小的BET表面积（887.3 m2/g）和孔容（0.81 cm3/g）。     

高硅分子筛MCM-41热稳定性与水热稳定性的初步研究

高硅分子筛ＭＣＭ－４１热稳定性与水热稳定性的初步研究董维阳,龙英才,郜晓琴,许太明,谢关根,高滋（复旦大学化学系,上海,２００４３３）关键词高硅分子筛ＭＣＭ－４１,热稳定性,水热稳定性,环己烷吸附等温线ＭＣＭ－４１是最近几年刚刚发现的中孔分子筛（Ｍ４...     

高纯度中孔分子筛MCM-41的合成与表征

用不同pH值的混合物制备了不同孔径的全硅MCM-41和不同金属离子取代的M-MCM-41(M=Al,Mn,Fe和V)分子筛.这些试样均呈现MCM-41的X射线粉末衍射特征峰和Ⅳ型氮气吸附等温线,但混有不同含量的无定形氧化硅.样品中MCM-41晶体的含量与溶胶的pH值和所用表面活性剂的碳链链长有关.骨架硅的金属离子取代降低了MCM-41的有序度,并且(100)面衍射峰强度从Al到V依次减弱.