稀土氧化物掺杂对SO4^2-／ZrO2／Al2O3催化剂催化性能的影响

采用浸溃-沉淀法在具有较大比表面积的Al2O3上直接合成纳米ZrO2制备负载型纳米ZrO2/Al2O3复合载体,并将氧化钪、氧化钕、氧化错等稀土氧化物(RExOy)分别掺杂到负载型纳米ZrO2/Al2O3复合载体中以改善ZrO2的表面性能.同时以此复合载体负载SO42-制备SO42-/RExOy-ZrO2/Al2O3催化剂.运用XRD,BET,NH3-TPD,原位红外等技术与方法对催化剂的晶相结构、比表面积、孔径分布、酸中心种类等进行表征,并以α-蒎烯异构化反应为探针考察了催化剂的催化性能.结果表明,掺杂的稀土氧化物没有改变ZrO2的晶相结构,但ZrO2粒度有所减小,催化剂的比表面积增加,同时稀土氧化物的存在还会改变催化剂表面SO42-的配位方式,提高表面酸中心数和酸强度,增强催化剂的活性.催化剂的孔结构对选择性有较大的影响.     

负载型纳米TiO2／Al2O3复合载体负载SO4^2-催化剂的制备与催化性能研究

分别采用沉淀法,水解法和溶胶凝胶法制备了负载型纳米TiO2/Al2O3复合载体,同时在复合载体表面负载SO42-制成SO42-/TiO2/Al2O3固体酸催化剂,并将此催化剂用于α-蒎烯异构化反应中.用XRD、FTIR,TPD等手段对催化剂的晶相结构、比表面积、孔径分布、表面酸性等进行了表征.结果表明,三种方法所制备的催化剂均为纳米级且拥有着丰富而规则的孔结构,水解法制备的SO42-/TiO2/Al2O3催化剂中TiO2的平均粒径(10.0 nm)较小,比表面积(172.88 m2/g)较大,平均孔径为3.926 nm,表面酸中心数和酸强度均高于沉淀法和溶胶凝胶法制备的催化剂,在α-蒎烯催化异化反应中的具有较高的活性,α-蒎烯转化率为82.76%.     

负载型纳米ZrO_2/Al_2O_3复合载体的制备和表征及其Ni/ZrO_2/Al_2O_3催化性能的研究

以大孔Al2O3为基载体,采用沉积-沉淀法和溶胶-沉积法制备了负载型纳米ZrO2/Al2O3复合载体.用XRD、TEM和比表面与孔径测定等手段对载体进行了表征.结果表明,负载型纳米ZrO2/Al2O3复合载体具有较大的比表面积和适宜的孔径分布,纳米ZrO2在载体上呈单层均匀分布.以CH4-CO2重整制合成气为探针反应,考察了Ni/ZrO2/Al2O3催化剂的活性和选择性.     

负载型纳米ZrO2/Al2O3复合载体的制备和表征及其Ni/ZrO2/Al2O3催化性能的研究

以大孔Al2O3为基载体，采用沉积-沉淀法和溶胶-沉积法制备了负载型纳米ZrO2/Al2O3复合载体．用XRD、TEM和比表面与孔径测定等手段对载体进行了表征．结果表明，负载型纳米ZrO2/Al2O3复合载体具有较大的比表面积和适宜的孔径分布，纳米ZrO2在载体上呈单层均匀分布．以CH4-CO2重整制合成气为探针反应，考察了Ni/ZrO2/Al2O3催化剂的活性和选择性．     

催化精馏专用填料型固体酸SO42-/ZrO2-Al2O3-Al的研究

为了研制催化精馏专用催化剂,采用铝阳极氧化法制备了Al2O3-Al一体型载体,并将活性固体超强酸SO42-/ZrO2引入到Al2O3-Al上,得到一种新型催化精馏专用填料式固体酸SO42-/ZrO2-Al2O3-Al催化剂.利用XRD、 SEM、 BET、 XPS、 NH3-TPD等手段对其进行了表征.结果表明,所制得的阳极氧化铝膜厚为56 μm, SO42-/ZrO2-Al2O3-Al固体酸具有比表面积大、酸强度适中的特点.XRD结果表明, ZrO2在Al2O3-Al上处于高度分散状态.将该固体酸用于乙酸/乙醇酯化反应中,显示出较高的催化活性,且稳定性较好.     

纳米ZrO2/Al2O3复合载体及Ni/ZrO2/Al2O3催化剂的性能研究

 采用溶胶-凝胶法在经过扩孔处理的Al2O3基载体上制备了纳米ZrO2/Al2O3复合载体,并通过浸渍法制备了NiO/ZrO2/Al2O3催化剂. 用XRD,TPR,TPD和N2吸附等技术分别考察了载体和催化剂的结构及表面性能,研究了复合载体对Ni/ZrO2/Al2O3催化CO2重整CH4反应性能的影响. 结果表明,纳米ZrO2/Al2O3复合载体具有较大的比表面积、适宜的孔径分布及稳定的t-ZrO2结构,Ni/ZrO2/Al2O3催化剂具有较好的CO2重整CH4反应活性和稳定性.     

制备方法对负载型纳米ZrO2/Al2O3复合载体性能的影响

采用浸渍-沉淀法制备了负载型纳米ZrO2/Al2O3复合载体.采用X射线衍射、N2物理吸附、差示扫描量热(DSC)和程序升温脱附等技术考察了浸渍方式和干燥方法对复合载体的表面性能、热稳定性和晶相结构的影响.结果表明,ZrO2/Al2O3复合载体中没有生成ZrO2-Al2O3复合氧化物或固溶体,纳米ZrO2仅负载在Al2O3的表面.微波干燥法制备的ZrO2/Al2O3复合载体的比表面积(158.7 m2/g)较大,最可几孔径为19.4 nm,ZrO2的粒度为4.2 nm,晶相结构为四方相ZrO2.微波诱导作用使ZrO2/Al2O3复合载体表面产生了新的酸碱中心,微波干燥法制备的ZrO2/Al2O3复合载体具有较强的热稳定性,在873~1 073 K范围内DSC曲线没有出现吸热峰,而其它干燥方法制备的复合载体在903~1 023 K范围内出现了较明显的吸热峰,表明复合载体表面的部分四方相ZrO2转变为单斜相ZrO2(m-ZrO2).对超声波处理过的复合载体进行微波干燥能进一步提高纳米ZrO2与Al2O3之间的相互作用,纳米粒子的粒度(3.4 nm)更小,分布更均匀,但没有改变ZrO2的晶相结构.     

ZrO2负载量对负载型纳米ZrO2/Al2O3复合载体的结构及性能影响

ZrO2在基载体Al2O3表面存在分散阈值(0.242 g/gAl2O3).在ZrO2/Al2O3复合载体中,ZrO2负载量不同其分布和粒度大小不同,当ZrO2负载量在0.242 g/gAl2O3-0.60 g/gAl2O3的范围内,ZrO2/Al2O3复合载体中纳米ZrO2的粒子的大小保持在4.2 nm,且单层分布在Al2O3的表面.当ZrO2负载量大于0.60 g/gAl2O3时,纳米粒子的粒径增大,并出现多层分布或堆积.XRD、DSC、HRTEM、XPS、H2-TPR结果表明,随着ZrO2负载量增大,复合载体中纳米ZrO2的分布由单层分布转化为多层或堆积分布,ZrO2负载量为0.60 g/gAl2O3时复合载体表面积最大(164.3 m2/g),ZrO2负载量的继续提高,复合载体的表面积明显下降.     

Ni／ZrO2-Al2O3制备表征及催化性能的研究

本文采用浸渍沉淀法制备了不同配比的ZrO2-Al2O3复合载体。并通过浸渍法制备Ni/ZrO2-Al2O3催化剂,以苯加氢制环己烷反应为探针,考察了ZrO2与Al2O3的配比对Ni催化剂催化加氢性能的影响;采用X射线衍射(XRD)、程序升温还原(TPR)、程序升温脱附(TPD)等技术考察复合载体对Ni催化剂的体相结构、还原性能以及表面吸附性能的影响。研究结果表明,ZrO2质量分数为20%的复合载体所负载的Ni催化剂有很好的加氢活性,优于单组分载体负载的Ni催化剂;采用浸渍沉淀法制备的ZrO2-Al2O3复合载体中ZrO2以非晶态形式存在,这是由于Al2O3的存在影响了ZrO2的内部结构;该载体负载的Ni催化剂较其他催化剂更容易被还原,吸附中心数量增加。     

Al含量对Pt-SO2-4/ZrO2-Al2O3固体超强酸催化正戊烷异构化性能的影响

通过向SO42-/ZrO2催化剂中同时引入适量的Pt和Al2O3,制备出了具有较高催化性能和稳定性的Pt-SO42-/ZrO2-Al2O3型固体超强酸催化剂.以正戊烷异构化反应为探针,考察了Al含量对催化剂性能的影响;并采用X射线衍射(XRD)、比表面积测定(BET)、红外(IR)光谱、程序升温还原(TPR)、热重-差热分析(TG-DTA)和氨-程序升温脱附(NH3-TPD)手段对催化剂进行了表征.结果表明,Al能够提高ZrO2的晶化温度,抑制硫的分解,增加催化剂的比表面积,增强硫氧键的结合,提高催化剂的还原性能,增加催化剂的酸强度和酸总量.当Al2O3含量(质量分数,w)为5.0%时,Pt-SO42-/ZrO2-Al2O3固体超强酸催化剂的催化活性最好,在100 h内异戊烷收率可稳定在52.0%以上,选择性在98.2%以上.     

Phase equilibria and glass formation in the As2S3-TlAs2S2Se2 section of the As2S3-As2Se3-TlS system

Alloys in the As₂S₃-TlAs₂S₂Se₂ section of the As₂S₃-As₂Se₃-TlS ternary system were studied and a phase diagram was constructed using physicochemical methods (differential thermal analysis, microstructural analysis, X-ray powder diffraction, also microhardness and density measurements). The diagram in the As₂S₃-TlAs₂S₂Se₂ section is a non-quasi-binary diagonal section of the As₂S₃-As₂Se₃-TlSe quasi-ternary system. It was found that all the alloys in the section under ordinary conditions are obtained in the vitreous state. At low As₂S₃ concentrations in the section, solid solutions form up to 2.5 mol %, and at low TlAs₂S₂Se₂ concentrations, their extent is 3 mol %.     

Natural radiative lifetimes in the2 S 1/2 and2 D 3/2, 5/2 sequences of neutral copper

Natural radiative lifetimes have been measured of the 3d ¹⁰ ns ² S _1/2 (n=6?10) and of the 3d ¹⁰ nd ² D _{3/2, 5/2} (n=5?9) sequences by using two step excitation of copper atoms in an atomic beam. The states investigated were populated by the light from two pulsed dye lasers pumped by the same Nd:YAG laser. The lifetimes of the² D sequence increase regularly with increasing principal quantum number. This is not the case for the² S series, because of configuration interaction in the² P series. In addition the lifetime of the 3d ¹⁰5p ² P _3/2 state has been measured together with its branching ratio.     

A theoretical study of the reaction of SiH2 with C2H2 and C2D2

Potential energy surfaces of the reaction of SiH₂ and C₂H₂ (and C₂D₂) have been calculated by means of ab initio molecular orbital theory at the QCISD/6-311G++(2df, 2p)//MP2/6-31G(d, p) level with corrections for the triple excitations to the QCISD energies. The barrier heights for the two reaction channels of the adduct, thus calculated, were further utilized for the dynamical calculation of the rate constants in the framework of quantum statistical Rice-Ramsperger-Kassel theory. Contributions of the rate constants of the various pathways to the total rate constant (K_T) for the disappearance of the reactants are critically examined and compared with experiment. The pressure dependence of K_T(C₂H₂) is primarily due to the formation of silirene. K_T(C₂D₂) is consistently higher than K_T(C₂H₂). The standard heat of formation of silirene is predicted to be 72.1 ± 3 kcal/mol. Rearrangement of silirene to vinylsilylene requires an activation energy smaller than that to silylacetylene.     

Fluorine sites in glasses and transparent glass-ceramics of the system Na2O/K2O/Al2O3/SiO2/BaF2

The transparent glass-ceramics obtained in the silicate system Na₂O/K₂O/SiO₂/BaF₂ show homogeneously dispersed BaF₂ nano crystals with a narrow size distribution. The X-ray diffraction and the nuclear magnetic resonance spectroscopy were applied to glasses and the respective glass-ceramics in order to clarify the crystallization mechanism and the role of fluorine during crystallization. With an increasing annealing time, the concentration and also the number of crystals remain approximately constant. With an increasing annealing temperature, the crystalline fraction increases until a saturation limit is reached, while the number of crystals decreases and the size of the crystals increases. Fluoride in the glassy network occurs as Al-F-Ba, Al-F-Na and also as Ba-F structures. The latter are transformed into crystalline BaF₂ and fluoride is removed from the Al-F-Ba/Na bonds. However, some fluorine is still present in the glassy phase after the crystallization.     

乙烷/H2O/O2/N2体系中光致过氧化物的产生

采用长光路Fourier红外光谱(LP-FTIR)和高压液相色谱(HPLC)技术研究了乙烷/H2O/O2/N2光化学体系中过氧化物的产生，证实乙烷降解产物中有过氧化氢、乙基过氧化氢(CH3CH2OOH,EHP)和过氧乙酸[CH3C(O)OOH,PAA]，并首次发现了甲基过氧化氢(CH3OOH,MHP)、羟甲基过氧化氢(HOCH2OOH,HMHP)和过氧甲醚(CH3OOCH3,DMP).H2O2,MHP和EHP的最大计算产率分别为6.8%，6.4%和6.7%，是乙烷降解生成的主要过氧化产物。MHP主要来自乙烷降解过程中的中间物乙醛的光解。HMHP的检出表明乙烷降解过程中可能有Criegee中间体.CH2OO.产生。OH自由基引发的乙烷降解反应可能是对流层大气H2O2，MHP及EHP的重要来源之一。     

New Compounds of the ThCr2Si2-Type and the Electronic Structure of CaM2Ge2 (M: Mn-Zn)

Two new compounds were synthesized by heating mixtures of the elements at 975-1025 K and characterized by single-crystal X-ray methods. CaZn₂Si₂ (a=4.173(2) Å, c=10.576(5) Å) and EuZn₂Ge₂ (a=4.348(2) Å, c=10.589(9) Å) crystallize in the ThCr₂Si₂-type structure (space group I4/mmm; Z=2). Magnetic susceptibility measurements of EuZn₂Ge₂ show Curie-Weiss behavior with a magnetic moment of 7.85(5)μ_B/Eu and a paramagnetic Curie temperature of 10(1) K. EuZn₂Ge₂ orders antiferromagnetically at T_N=10.0(5) K and undergoes a metamagnetic transition at a low critical field of about 0.3(2) T. The saturation magnetization at 2 K and 5.5 T is 6.60(5) μ_B/Eu. ¹⁵¹Eu Mössbauer spectroscopic experiments show one signal at 78 K at an isomer shift of −11.4(1) mm/s and a line width of 2.7(1) mm/s compatible with divalent europium. At 4.2 K full magnetic hyperfine field splitting with a field of 26.4(4) T is detected. The already known compounds CaM₂Ge₂ (M: Mn-Zn) also crystallize in the ThCr₂Si₂-type structure. Their MGe₄ tetrahedra are strongly distorted with M=Ni and nearly undistorted with M=Mn or Zn. According to LMTO electronic band structure calculations, the distortion is driven by a charge transfer from M-Ge antibonding to bonding levels.     

Approaches to the synthesis of CF2-analogues of 2-deoxy-2-aminoglycosides

The preparation of a fluorinated C-glycosidic analogue of a 2-deoxy-2-acetamido-d-altrose is described. The synthetic sequence involves the addition of a difluoroenoxysilane to a d-glucal, an epoxidation of the resulting unsaturated CF₂-glycoside and a ring-opening reaction with TMSN₃. An Overman rearrangement of the unsaturated intermediate is also described.     

P2O5对Li2O-SiO2-Al2O3-K2O-ZnO体系微晶玻璃析晶性能的影响

采用差热分析、X射线衍射及扫描电镜分析手段研究了P₂O₅对Li₂O-SiO₂-Al₂O₃-K₂O-ZnO体系牙科微晶玻璃析晶性能的影响, 并确定了P₂O₅的最适含量. 结果发现P₂O₅是该玻璃体系的有效成核剂, 未添加P₂O₅的玻璃体系成核密度低, 热处理后不能形成微晶体, 且主晶相为硅酸锂; 添加P₂O₅使玻璃在热处理后形成以二硅酸锂为主晶相的微晶玻璃. 该玻璃体系中添加4.5 wt%的P₂O₅可以得到较高体积含量和理想显微结构的牙科二硅酸锂微晶玻璃. P₂O₅含量为6 wt%的基质玻璃发生乳浊, 呈不透明的乳白色.     

Phase diagram and infrared-spectral investigation of the 2TeO2 · V2O5-Na2O · V2O5 · 2TeO2 system

The phase diagram of the 2TeO₂ · V₂O₅-Na₂O · V₂O₅ · 2TeO₂ system is studied by X-ray diffraction, ir spectroscopy, and DTA. A new compound with a composition of Na₂O · 3V₂O₅ · 6TeO₂ is established. The ir spectra of the alkaline trivanadates are interpreted. They are considered as structural analogs of the new phase. As a result of this comparison, the postulate is made that the main structural units in the Na₂O · 3V₂O₅ · 6TeO₂ compound are V₂O₈ groups, while tellurium is present both in the TeO₃ and TeO₄ groups. Contrary to the crystal phases, in glasses the transition from VO₅ toward VO₄ does not proceed through the formation of new structural units of vanadium; but rather a gradual transition of the structure is observed with a change in the composition from 2TeO₂ · V₂O₅ to Na₂O · V₂O₅ · 2TeO₂.     

Polymorphism in the Sc2Si2O7-Y2Si2O7 system

This paper examines the structural changes with temperature and composition in the Sc₂Si₂O₇-Y₂Si₂O₇ system; members of this system are expected to form in the intergranular region of Si₃N₄ and SiC structural ceramics when sintered with the aid of Y₂O₃ and Sc₂O₃ mixtures. A set of different compositions have been synthesized using the sol-gel method to obtain a xerogel, which has been calcined at temperatures between 1300 and 1750 °C during different times. The temperature-composition diagram of the system, obtained from powder XRD data, is dominated by the β-RE₂Si₂O₇ polymorph, with γ-RE₂Si₂O₇ and δ-RE₂Si₂O₇ showing very reduced stability fields. Isotherms at 1300 and 1600 °C have been analysed in detail to evaluate the solid solubility of the components. Although, the XRD data show a complete solid solubility of β-Sc₂Si₂O₇ in β-Y₂Si₂O₇ at 1300 °C, the ²⁹Si MAS-NMR spectra indicate a local structural change at x ca. 1.15 (Sc_2−xY_xSi₂O₇) related to the configuration of the Si tetrahedron, which does not affect the long-range order of the β-RE₂Si₂O₇ structure. Finally, it is interesting to note that, although Sc₂Si₂O₇ shows a unique stable polymorph (β), Sc³⁺ is able to replace Y³⁺ in γ-Y₂Si₂O₇ in the compositional range 1.86?x?2 (where x is Sc_2−xY_xSi₂O₇) as well as in δ-Y₂Si₂O₇ for compositions much closer to the pure Y₂Si₂O₇.