稀土氧化物的掺杂量对SO42-/ZrO2/Al2O3催化剂催化性能的影响

采用浸渍-沉淀法制备负载型纳米ZrO2/Al2O3,复合载体,并将不同量的氧化钕、氧化镨掺杂到负载型纳米ZrO2/Al2O3复合载体中以调变ZrO2的表面性能.同时以此复合载体负载SO42-制备SO42-/REXOY-ZrO2/Al2O3催化剂.运用XHD、BET、NH3-TPD、原位红外技术对催化剂的晶相结构、比表面积、孔径分布、酸中心种类等进行表征,并以α-蒎烯异构化为探针反应考察了催化剂的活性.结果表明,适量的稀土掺杂会增加催化剂的比表面积,降低ZrO2的粒径,从而增加催化剂表面SO42-的配位吸附量,提高表面酸中心数和酸强度,增强催化剂的活性.     

负载型纳米TiO2／Al2O3复合载体负载SO4^2-催化剂的制备与催化性能研究

分别采用沉淀法,水解法和溶胶凝胶法制备了负载型纳米TiO2/Al2O3复合载体,同时在复合载体表面负载SO42-制成SO42-/TiO2/Al2O3固体酸催化剂,并将此催化剂用于α-蒎烯异构化反应中.用XRD、FTIR,TPD等手段对催化剂的晶相结构、比表面积、孔径分布、表面酸性等进行了表征.结果表明,三种方法所制备的催化剂均为纳米级且拥有着丰富而规则的孔结构,水解法制备的SO42-/TiO2/Al2O3催化剂中TiO2的平均粒径(10.0 nm)较小,比表面积(172.88 m2/g)较大,平均孔径为3.926 nm,表面酸中心数和酸强度均高于沉淀法和溶胶凝胶法制备的催化剂,在α-蒎烯催化异化反应中的具有较高的活性,α-蒎烯转化率为82.76%.     

制备方法对负载型纳米ZrO2/Al2O3复合载体性能的影响

采用浸渍-沉淀法制备了负载型纳米ZrO2/Al2O3复合载体.采用X射线衍射、N2物理吸附、差示扫描量热(DSC)和程序升温脱附等技术考察了浸渍方式和干燥方法对复合载体的表面性能、热稳定性和晶相结构的影响.结果表明,ZrO2/Al2O3复合载体中没有生成ZrO2-Al2O3复合氧化物或固溶体,纳米ZrO2仅负载在Al2O3的表面.微波干燥法制备的ZrO2/Al2O3复合载体的比表面积(158.7 m2/g)较大,最可几孔径为19.4 nm,ZrO2的粒度为4.2 nm,晶相结构为四方相ZrO2.微波诱导作用使ZrO2/Al2O3复合载体表面产生了新的酸碱中心,微波干燥法制备的ZrO2/Al2O3复合载体具有较强的热稳定性,在873~1 073 K范围内DSC曲线没有出现吸热峰,而其它干燥方法制备的复合载体在903~1 023 K范围内出现了较明显的吸热峰,表明复合载体表面的部分四方相ZrO2转变为单斜相ZrO2(m-ZrO2).对超声波处理过的复合载体进行微波干燥能进一步提高纳米ZrO2与Al2O3之间的相互作用,纳米粒子的粒度(3.4 nm)更小,分布更均匀,但没有改变ZrO2的晶相结构.     

负载型纳米ZrO_2/Al_2O_3复合载体的制备和表征及其Ni/ZrO_2/Al_2O_3催化性能的研究

以大孔Al2O3为基载体,采用沉积-沉淀法和溶胶-沉积法制备了负载型纳米ZrO2/Al2O3复合载体.用XRD、TEM和比表面与孔径测定等手段对载体进行了表征.结果表明,负载型纳米ZrO2/Al2O3复合载体具有较大的比表面积和适宜的孔径分布,纳米ZrO2在载体上呈单层均匀分布.以CH4-CO2重整制合成气为探针反应,考察了Ni/ZrO2/Al2O3催化剂的活性和选择性.     

催化精馏专用填料型固体酸SO42-/ZrO2-Al2O3-Al的研究

为了研制催化精馏专用催化剂,采用铝阳极氧化法制备了Al2O3-Al一体型载体,并将活性固体超强酸SO42-/ZrO2引入到Al2O3-Al上,得到一种新型催化精馏专用填料式固体酸SO42-/ZrO2-Al2O3-Al催化剂.利用XRD、 SEM、 BET、 XPS、 NH3-TPD等手段对其进行了表征.结果表明,所制得的阳极氧化铝膜厚为56 μm, SO42-/ZrO2-Al2O3-Al固体酸具有比表面积大、酸强度适中的特点.XRD结果表明, ZrO2在Al2O3-Al上处于高度分散状态.将该固体酸用于乙酸/乙醇酯化反应中,显示出较高的催化活性,且稳定性较好.     

负载型纳米ZrO2/Al2O3复合载体的制备和表征及其Ni/ZrO2/Al2O3催化性能的研究

以大孔Al2O3为基载体，采用沉积-沉淀法和溶胶-沉积法制备了负载型纳米ZrO2/Al2O3复合载体．用XRD、TEM和比表面与孔径测定等手段对载体进行了表征．结果表明，负载型纳米ZrO2/Al2O3复合载体具有较大的比表面积和适宜的孔径分布，纳米ZrO2在载体上呈单层均匀分布．以CH4-CO2重整制合成气为探针反应，考察了Ni/ZrO2/Al2O3催化剂的活性和选择性．     

纳米ZrO2/Al2O3复合载体及Ni/ZrO2/Al2O3催化剂的性能研究

 采用溶胶-凝胶法在经过扩孔处理的Al2O3基载体上制备了纳米ZrO2/Al2O3复合载体,并通过浸渍法制备了NiO/ZrO2/Al2O3催化剂. 用XRD,TPR,TPD和N2吸附等技术分别考察了载体和催化剂的结构及表面性能,研究了复合载体对Ni/ZrO2/Al2O3催化CO2重整CH4反应性能的影响. 结果表明,纳米ZrO2/Al2O3复合载体具有较大的比表面积、适宜的孔径分布及稳定的t-ZrO2结构,Ni/ZrO2/Al2O3催化剂具有较好的CO2重整CH4反应活性和稳定性.     

ZrO2负载量对负载型纳米ZrO2/Al2O3复合载体的结构及性能影响

ZrO2在基载体Al2O3表面存在分散阈值(0.242 g/gAl2O3).在ZrO2/Al2O3复合载体中,ZrO2负载量不同其分布和粒度大小不同,当ZrO2负载量在0.242 g/gAl2O3-0.60 g/gAl2O3的范围内,ZrO2/Al2O3复合载体中纳米ZrO2的粒子的大小保持在4.2 nm,且单层分布在Al2O3的表面.当ZrO2负载量大于0.60 g/gAl2O3时,纳米粒子的粒径增大,并出现多层分布或堆积.XRD、DSC、HRTEM、XPS、H2-TPR结果表明,随着ZrO2负载量增大,复合载体中纳米ZrO2的分布由单层分布转化为多层或堆积分布,ZrO2负载量为0.60 g/gAl2O3时复合载体表面积最大(164.3 m2/g),ZrO2负载量的继续提高,复合载体的表面积明显下降.     

负载Pd密偶催化剂的载体效应

采用尿素水解法或吸附沉淀法制备了金属氧化物载体,并用浸渍法负载0.5%Pd制得了Pd/Sn0.4Zr0.6O2,Pd/ZrO2,Pd/SnO2,Pd/SnO2-Al2O3和Pd/Al2O3催化剂.采用原位漫反射红外光谱、拉曼光谱、X射线光电子能谱和程序升温还原等方法对催化剂结构进行了表征,探讨了不同载体对表面PdOx物种化学吸附性质和氧化还原性能的影响,并与样品的丙烷氧化活性相关联.漫反射红外光谱表明,在Pd/SnO2-Al2O3中,Sn对Al2O3表面的Pd原子簇起到稀释作用,促进了Pd的分散,使得其CO线式吸附强度明显高于Pd/Al2O3,但Pd过高的分散度不仅减少了表面Pd-PdO活性位对的数目,而且使反应中间物种Pd-OH之间脱水困难,因而阻塞了活性位,降低了其循环氧化还原活性;而在Sn0.4Zr0.6O2复合氧化物载体中,SnO2有效地阻止了四方晶相ZrO2向稳态单斜晶相转变,且复合载体的比表面积较ZrO2和SnO2有所增加,其表面PdOx物种的分散度适中.此外,Sn0.4Zr0.6O2复合氧化物负载的Pd的价态介于Pd0与Pd2 之间,表面氧空位较多,促进了丙烷中C-H键的活化,使比表面积较低的Pd/Sn0.4Zr0.6O2具有最好的催化丙烷氧化能力,相反比表面积较高的Pd/SnO2-Al2O3活性很差,说明分散度适中且具有较低氧化态的PdOx(0相似文献   

CuCl／SiO2-Al2O3催化剂的表面结构及甲醇氧化羰基化催化性能

通过掺杂Al对无定形层析硅胶进行表面改性,采用固体离子交换法制备了CuCl/SiO2-Al2O3催化剂,并考察了它在甲醇液相氧化羰基化合成碳酸二甲酯反应中的催化性能.结果表明,掺杂Al制备的SiO2-Al2O3载体仍保持了硅胶的无定形结构,比表面积降为200m2/g,但表面酸性明显增强,具有B酸中心.CuCl不仅分散于SiO2-Al2O3载体表面,而且与载体表面的B酸发生离子交换作用形成了表面Cu 物种,使催化剂比表面积降为148m2/g,且两种Cu 物种共同构成了催化活性中心.当CuCl/SiO2-Al2O3催化剂的Si/Al比为5,在500℃焙烧时,催化剂上甲醇氧化羰基化反应的碳酸二甲酯的选择性和时空收率分别达到74%和1.27g/(g.h).     

Formation of nano-crystalline quartz crystals from ZnO/MgO/Al2O3/TiO2/ZrO2/SiO2 glasses

Glasses with the compositions 50.9 SiO₂ · 20.8 Al₂O₃ · (20.8 ? x) MgO· × ZnO · 3.7 TiO₂ · 3.7 ZrO₂ with x = 0, 2.3, 4.6 and 9.3 were annealed at temperatures in the range from 850 to 1100 °C. Depending on temperature, high- or low-quartz solid solutions, magnesium aluminosilicate, mullit and spinel precipitated. These glass–ceramics exhibit excellent mechanical properties and are potential candidates for applications in micromechanics or as hard disc substrate.The larger the ZnO concentration, the lower is the glass transition temperature. Also microhardnesses and Young’s moduli increased with increasing ZnO concentration. The nucleation temperature was of minor importance. To achieve good mechanical properties, the initially formed high-quartz phase must transform to the corresponding low-quartz phase. This occurs if the quartz phase contains only minor MgO or ZnO concentrations, which can be achieved by increasing the annealing times or temperature. Then MgO, ZnO and Al₂O₃ occur as separate spinel or gahnite phase.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Synthesis and characterization of inorganic solid electrolytes of Li2O-SiO2-P2O5 and Li2O-TiO2-SiO2-P2O5 systems

The lithium-ion-conducting inorganic solid electrolytes in the oxide systems Li₂O-SiO₂-P₂O₅ and Li₂O-TiO₂-SiO₂-P₂O₅ were prepared by the solid-state reaction, and the electrolyte pellet made by cold-pressing method had diameter of 13 mm and was about 1 mm thick. Phase identification and surface morphology of the products were carried out by X-ray diffraction and scanning electron microscopy. Ionic conductivity of the pellets was investigated through ac impedance. The results show that the adding of other cations can improve the ionic conductivity of the solid electrolyte, and the sintering temperature and duration can influence the ionic conductivity. The maximum ionic conductivity in the samples is 9.9 × 10⁻⁴ S/cm in the Li₂O-TiO₂-SiO₂-P₂O₅ system. Original Russian Text ? W. Li, M. Wang, Z.H. Li, X.F. Shang, H. Wang, Y.W. Wang, Y.B. Xu, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 11, pp. 1341–1345.     

The preparation of NbH5(Me2PCH2CH2Me2)2 and NbHL2(Me2PCH2CH2PMe2)2 (L = CO or C2H4)

MMe₅(dmpe) (M = Nb or Ta, dmpe = Me₂PCH₂CH₂PMe₂) reacts with H₂ (500 atm) and dmpe in THF at 60°C to give MH₅(dmpe)_2? NbH₅(dmpe)₂ readily reacts with two mol of CO or ethylene (L) to give NbHL₂(dmpe)₂. The exchange of the hydride ligand with the ethylene protons in NbH(C₂H₄)₂(dmpe)₂ is not rapid on the ¹H NMR time scale (60 MHz) at 95°C.     

Removal of NO in NO/N2, NO/N2/O2, NO/CH4/N2, and NO/CH4/O2/N2 systems by flowing microwave discharges

In this paper, continuing previous work, we report on experiments carried out to investigate the removal of NO from simulated flue gas in nonthermal plasmas. The plasma-induced decomposition of small concentrations of NO in N2 used as the carrier gas and O2 and CH4 as minority components has been studied in a surface wave discharge induced with a surfatron launcher. The reaction products and efficiency have been monitored by mass spectrometry as a function of the composition of the mixture. NO is effectively decomposed into N2 and O2 even in the presence of O2, provided always that enough CH4 is also present in the mixture. Other majority products of the plasma reactions under these conditions are NH3, CO, and H2. In the absence of O2, decomposition of NO also occurs, although in that case HCN accompanies the other reaction products as a majority component. The plasma for the different reaction mixtures has been characterized by optical emission spectroscopy. Intermediate excited species of NO*, C*, CN*, NH*, and CH* have been monitored depending on the gas mixture. The type of species detected and their evolution with the gas composition are in agreement with the reaction products detected in each case. The observations by mass spectrometry and optical emission spectroscopy are in agreement with the kinetic reaction models available in literature for simple plasma reactions in simple reaction mixtures.     

Direct formation of cyclobutenylphosphonates from 1-alkynylphosphonates and Cp2ZrCl2/2EtMgCl/2CuCl

Zirconacycles 2 prepared from 1-alkynylphosphonates 1, zirconocene dichloride, and 2 equiv of EtMgCl are smoothly converted into cyclobutenylphosphonates 3 when treated with two equiv of CuCl in 65-81% isolated yield. The reaction is specific and general only for zirconacyclopentenyl phosphonates.     

TiO2/SiO2/CeO2复合纳米薄膜超亲水性能的研究

采用溶胶凝胶法在载玻片表面制备了均匀透明的TiO2-SiO2-CeO2超亲水性薄膜，并用X射线衍射、傅立叶红外光谱、紫外-可见分光光度计研究了SiO2及稀土铈添加对TiO2薄膜表面特征及超亲水性能的影响。结果表明，Ti02-SiO2-CeO2薄膜亲水性能及亲水持续效应显著提高。实验中掺杂的铈是以三价离子态引入的，由于Ce^3 在高温下很容易氧化，故在薄膜中铈主要以四价态形式存在。Ce^4 在光激发下很容易捕获光生电子生成Ce^3 离子，光生空穴则与表面氧离子反应形成氧空位，而氧空位对亲水性的提高具有关键作用。添加SiO2后，薄膜表面的羟基含量增加，这主要是由于TiO2与SiO2复合在表面形成Lewis酸所致。表面稳定的羟基可使亲水性在暗中保持较长时间，因而亲水持续效应提高。添加SiO2及稀土铈后，薄膜中TiO2晶粒尺寸变小，量子效应增强，这也导致亲水性提高。因此添加稀土铈及SiO2后，薄膜表面的氧空穴增多，薄膜的超亲水性及亲水持续效应提高。     

Formation of [Cp2TiSbMe2]2, [Cp2TiSb(SiMe3)2]2 and [Cp2TiCl]2·2Mes4Sb2

Reactions of [Cp₂Ti(btmsa)] (btmsa = bis(trimethylsilyl)acetylene) with R₄Sb₂ (R = Me, Me₃Si) give [Cp₂TiSbMe₂]₂ (1) or [Cp₂TiSb(SiMe₃)₂]₂ (2) respectively. [Cp₂TiCl]₂·2Mes₄Sb₂ (3) is serendipitously formed from [Cp₂Ti(btmsa)] and Mes₂SbH containing NH₄Cl traces.     

Fluorine sites in glasses and transparent glass-ceramics of the system Na2O/K2O/Al2O3/SiO2/BaF2

The transparent glass-ceramics obtained in the silicate system Na₂O/K₂O/SiO₂/BaF₂ show homogeneously dispersed BaF₂ nano crystals with a narrow size distribution. The X-ray diffraction and the nuclear magnetic resonance spectroscopy were applied to glasses and the respective glass-ceramics in order to clarify the crystallization mechanism and the role of fluorine during crystallization. With an increasing annealing time, the concentration and also the number of crystals remain approximately constant. With an increasing annealing temperature, the crystalline fraction increases until a saturation limit is reached, while the number of crystals decreases and the size of the crystals increases. Fluoride in the glassy network occurs as Al-F-Ba, Al-F-Na and also as Ba-F structures. The latter are transformed into crystalline BaF₂ and fluoride is removed from the Al-F-Ba/Na bonds. However, some fluorine is still present in the glassy phase after the crystallization.     

Study of plasma-polymerization deposition of C2H2/CO2/H2 onto ethylene-co-propylene rubber membranes

Ethylene-co-propylene rubber (ERP) membranes were modified by use of acetylene/carbon dioxide/hydrogen (C₂H₂/CO₂/H₂) plasma-polymerization deposition. The influence of flow rate of gases, glow discharge power and deposition time on the amount of deposition was investigated. Infrared spectroscopy and scanning electron microscopy were employed to study the structure and surface morphology of the deposited EPR membrane. The water contact angle and the permeation property were examined as well. The results showed that deposition comprises oxygen-containing groups including >C=O and –OH, the hydrophilicity of EPR membrane was therefore improved. It was also found that the permeation coefficient of plasma modified EPR membrane decreased with the increase of the amount of deposition.