高折光指数光学树脂的合成——相转移法合成不饱和硫醇酯单体的条件控制

采用正常的低温相转移催化（ＰＴＣ）和反滴碱溶液ＰＴＣ法分别合成了含硫双烯ＭＥＳＤＭＡ和单烯ＭＥＰＳＭＡ．１Ｈ ＮＭＲ分析证明ＭＥＳ中的杂质主要是由原料ＴＤＧ引入的．对含单个巯基的ＭＥＰＳ的正常ＰＴＣ酯化接枝双键，因存在巯基和不饱和双键的加成反应而导致失败．作者最终得到了折光指数在１６２５以上的ＭＥＳＤＭＡ／ＭＥＰＳＭＡ共聚物．     

二苯醚—对苯二甲酰氯—4,4‘—二苯氧基二苯砜三元共聚物的合成与性能

以无水ＡｌＣｌ３／ＣｌＣＨ２ＣＨ２Ｃｌ／ＮＭＰ为催化剂／溶剂体系，通过缩聚反应，由二苯醚，对苯二甲酰氯和４，４－二苯氧基二苯砜合成了聚醚酮酮和聚醚砜醚酮酮共聚物（ＰＥＫＫ／ＰＥＳＥＫＫ）．考察了单体浓度、反应时间对聚合物分子量的影响，并对其进行了ＩＲ、ＤＳＣ、ＷＡＸＤ等分析表征．结果表明，共聚物具有优异的耐热性，随着共聚物中ＰＥＳＥＫＫ单元含量的增加，其玻璃化温度逐渐升高，而熔融温度和结晶度逐渐降低．与聚醚酮酮（ＰＥＫＫ）相比，共聚物的断裂伸长率明显提高，而拉伸强度和拉伸模量却有所下降，但仍具有良好的力学性能．     

氯化聚乙烯对甲基丙烯酸甲酯／苯乙烯共聚动力学的影响

将甲基丙烯酸甲酯（ＭＭＡ）／苯乙烯（Ｓ）在氯化聚乙烯（ＣＰＥ）存在下进行悬浮溶胀接枝共聚，考察了ＣＰＥ对ＭＭＡ／Ｓ共聚动力学行为的影响．ＣＰＥ提高了聚合体系的粘度，使自动加速提前，扩散因素增加，对共聚有阻滞作用．ＣＰＥ是链转移剂，使ＭＭＡ／Ｓ共聚物分子量降低．ＣＰＥ对ＭＭＡ的吸附渗透优于对Ｓ的吸附，造成接技部分与非接技部分组成的差异．ＣＰＥ含量、溶胀时间、转化率、硫酸用量对共聚组成均有影响。     

聚环氧乙烷为支链的两亲共聚物的表征及性能

用端基带有甲基丙烯酸酯的聚环氧乙烷大分子单体（ＰＥＯ—ＭＡ）分别与小分子单体苯乙烯（Ｓ）、甲基丙烯酸甲酯（ＭＭＡ）、丙烯酸甲酯（ＭＡ）溶液自由基共聚合得到了三种具有不同主链结构的以聚环氧乙烷（ＰＥＯ）为支链的两亲接枝嵌段共聚物（分别简写为：ＰＳ─ｇ─ＰＥＯ，ＰＭＭＡ─ｇ─ＰＥＯ，ＰＭＡ─ｇ─ＰＥＯ）．用ＧＰＣ、ＩＲ、１Ｈ─ＮＭＲ、ＷＡＸＤ和ＤＳＣ对其结构进行了表征．研究了接校共聚物的结晶性能、乳化性能以及在Ｗｉｌｌｉａｍｓｏｎ反应中相转移催化作用．结果表明，不同主链结构有不同的结晶度，并随支链ＰＥＯ含量的增加，分子量的增大而提高；其乳化体积和相转移催化反应的转化率均随着共聚物浓度的增加、支链ＰＥＯ含量的增人而增大，随支链ＰＥＯ分子量的提高而减小．     

刚性链嵌段共聚物的研究（Ⅳ）—聚醚醚酮／苯酞圈型聚芳醚砜…

以聚醚醚酮（ＰＥＥＫ）和苯酞圈型聚芳醚砜（ＰＤＣ）齐聚物为原料，通过溶液缩聚法制备了ＰＥＥＫ／ＰＤＣ有规嵌段共聚物系列样品。经ＤＳＣ、ＷＡＸＤ、ＴＧＡ、ＤＭＡ等方法研究表明：共聚物没有微相分离现象；其结晶属于简单正交晶系，ＰＤＣ含量对共聚物结晶行为产生很大影响；热稳定性随ＰＤＣ含量增加而明显降低；共聚物具有优异的力学性能，拉伸强度和储能模量高于ＰＥＥＫ。     

中空纤维催化膜反应器中环戊二烯的选择加氢反应

将聚乙烯吡咯烷酮（ＰＶＰ）负载钯催化剂（ＰＶＰ－Ｐｄ）镶嵌到三种醋酸纤维（ＣＡ）中空膜（ＣＡ－Ｉ，ＣＡ－Ⅱ，ＣＡ－Ⅲ）内制各中空纤维催化膜，并进一步制成催化膜反应器，在４０℃和０．１ＭＰａ的反应条件下，在催化膜反应器中进行了环戊二烯的选择加氢反应，考察了具有不同氢气渗透率的醋酸纤维丝组成的三种膜反应器对反应的转化率及选择性的影响，并在此基础上考察了各种反应参数对反应的影响，ＣＡ中空纤维催化膜对环戊     

刚性链嵌段共聚物的研究（Ⅳ）──聚醚醚酮／苯酞圈型聚芳醚砜有规嵌段共聚物的合成与部分性能

以聚醚醚酮（ＰＥＥＫ）和苯酞圈型聚芳醚砜（ＰＤＣ）齐聚物为原料，通过溶液缩聚法制备了ＰＥＥＫ／ＰＤＣ有规嵌段共聚物系列样品。经ＤＳＣ、ＷＡＸＤ、ＴＧＡ、ＤＭＡ等方法研究表明：共聚物没有微相分离现象；其结晶属于简单正交晶系，ＰＤＣ含量对共聚物结晶行为产生很大影响；热稳定性随ＰＤＣ含量增加而明显降低；共聚物具有优异的力学性能，拉伸强度和储能模量高于ＰＥＥＫ。     

聚酯酰胺的合成及表征

用两种方法合成了聚酯酰胺（ＰＥＡ）共聚物．一种是两步法，即先合成对苯二甲酸乙醇酰胺（ＢＡＥＴ）单体，然后与对苯二甲酸乙二酯（ＢＨＥＴ）共缩聚；另一种是一步法．即在酯交换反应中直接添加乙醇胺（ＥＡ）．两种方法制得的聚酯酰胺（ＰＥＡ）共聚物测试证明了为产物，并分析了合成中的化学反应．     

用含偶氮基的聚苯乙烯大分子引发剂合成两亲性嵌段共聚物

采用含偶氮基的聚苯乙烯预聚物（ＰＳ ＡＣＰＣ）作为引发剂，合成了苯乙烯（Ｓｔ）分别与甲基丙烯酸（ＭＡＡ）、甲基丙烯酸（β 羟丙酯）（ＨＰＭＡ）的嵌段共聚物，考察了ＰＳ ＡＣＰＣ引发第二单体的聚合反应行为，以及影响第二单体转化率和均聚物含量、共聚物组成的因素．用溶解性、凝胶渗透色谱（ＧＰＣ）、红外光谱（ＩＲ）、核磁共振（ＮＭＲ）、动态接触角（ＤＣＡ）等表征了嵌段共聚物．     

聚酯酰胺的合成及表征

 用两种方法合成了聚酯酰胺（ＰＥＡ）共聚物．一种是两步法，即先合成对苯二甲酸乙醇酰胺（ＢＡＥＴ）单体，然后与对苯二甲酸乙二酯（ＢＨＥＴ）共缩聚；另一种是一步法．即在酯交换反应中直接添加乙醇胺（ＥＡ）．两种方法制得的聚酯酰胺（ＰＥＡ）共聚物测试证明了为产物，并分析了合成中的化学反应．     

Synthesis of poly(ethyl acrylate) by single electron transfer‐degenerative chain transfer living radical polymerization in water catalyzed by Na2S2O4

Living radical polymerization of ethyl acrylate was achieved by single‐electron‐transfer/degenerative‐chain transfer mediated living radical polymerization in water catalyzed by sodium dithionite. The plots of number‐average molecular weight versus conversion and ln[M]₀/[M] versus time are linear, indicating a controlled polymerization. This method leads to the preparation of α,ω‐di(iodo)poly(ethyl acrylate) (α,ω‐di(iodo)PEtA) macroinitiator that can be further functionalized. The molecular weight distributions were determined using a combination of three detectors (TriSEC): right‐angle light scattering, a differential viscometer and refractive index. The method studied in this work represents a possible route to prepare well‐tailored macromolecules made of ethyl acrylate in environmental friendly reaction medium. To the best of our knowledge there is no previous report dealing with the synthesis of PEtA by any LRP approach in aqueous medium. Furthermore, the method described in this article was successfully applied in pilot scale reactions under industrial production conditions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 421–432, 2008     

醇溶性聚丙烯酸酯乳液的合成及性能研究

以丙烯酸乙酯(EA)、甲基丙烯酸甲酯(MMA)和甲基丙烯酸(MAA)为主单体,采用过硫酸盐作引发剂,经预乳化乳液聚合工艺合成了聚丙烯酸酯乳液.讨论了乳化剂种类、单体种类以及功能性单体、引发剂加入工艺对乳液聚合过程及乳液产品性能的影响.结果表明:单体组成为m(MMA)∶m(EA)∶m(MAA)=45∶40∶15所得乳液聚合物能满足使用性能要求;种子引发剂加入质量控制在单体总质量的0.3%,而总的引发剂用量占单体总质量的0.8%较适宜.用差热分析仪和凝胶渗透色谱仪对乳液聚合物进行了表征.     

Thermal degradation of poly(ethyl methacrylate) and its copolymer with poly(ethyl acrylate)

The thermal degradation behaviour of poly(ethyl methacrylate) homopolymers and poly(ethyl methacrylate) and poly(ethyl acrylate) copolymers synthesized by using the benzoyl peroxide-di-methyl aniline redox pair at different temperatures (18–35C) was investigated. Contrary to some reports in the literature, the thermal degradation of PEMA was observed to take place in multi steps. These are assigned to be loss of labile end groups, side chain scission, anhydride formation and main chain degradation steps. Dominating chemical formations at the end of these steps were characterized by FTIR spectroscopy.The homopolymer samples synthesized at 18C showed a greater thermal stability against degradation. Copolymerization with small amounts of ethyl acrylate was observed to impart thermal stability to PEMA by stabilizing mainly the end groups against degradations.     

淀粉接枝丙烯酸乙酯及其增容性

研究了在挤出机中采用高温和剪切力的作用直接引发淀粉与丙烯酸乙酯的接枝共聚合反应．讨论了反应条件对接枝反应的影响，研究了接枝物在淀粉与聚乙烯共混物中的增容作用．实验结果表明，高温和剪切力可以引发淀粉与丙烯酸乙酯的接枝共聚合反应．接枝物作为增容剂，可以明显地改善淀粉与聚乙烯共混物的力学性能和流变性能．     

Preparation,characterization and thermal stability of poly[2-(Dimethylamino)ethyl acrylate]

Poly[2-(dimethylamino)ethyl acrylate] (PDAEA) and polymer complexes of 2-(dimethylamino)ethyl acrylate (DAEA) with nickel(II), copper(II), iron(III) and cobalt(II) chlorides were prepared and characterized by means of IR, electronic spectra and elemental analysis. The thermal stability of the homopolymer was compared with those of the polymer complexes, and the order of stability was given. The activation energies of the polymer complexes were calculated.     

N-乙烯基咪唑鎓盐聚合物的合成、表征及其电化学性能

以N-乙烯基咪唑、溴丁烷、丙烯酸乙酯为原料,合成了聚溴化N-乙烯基-N’-丁基咪唑以及溴化N-乙烯基-N’-丁基咪唑丽烯酸乙酯共聚物,通过红外、核磁、元素分析对其结构进行了表征．采用阴极极化曲线测试了其电化学性能,结果表明两者对铜离子阴极还原产生了极大的极化作用．     

Investigation of ultraviolet curable waterborne polyurethane acrylate dispersion based on hydroxyl-terminated polybutadiene

A new kind of ultraviolet (UV) curable waterborne polyurethane acrylate dispersion was synthesized based on hydroxyl-terminated polybutadiene (HTPB), poly-(propylene glycol) (PPG), isophorene diisocyanate (IPDI), 2-hydroxy ethyl acrylate (HEA) and dimethylol propionic acid (DMPA) after neutralizing by triethylamine (TEA). 2-Hydroxy-1-[4-2-hydroxyethoxy) phenyl]-2-methyl-1-propanone (Irgacure 2959) was used as a photoinitiator and deionized water as a diluent. Fourier transform infrared (FTIR) analysis was used to identify the chain structure of the UV-curable polyurethane prepolymer based on HTPB and the curing process. Effects of relative content of HTPB and PPG on emulsion stability, resistance to water and ethanol, thermal stability, compatibility of soft and hard segment, as well as the mechanical property of the cured film were investigated. Translated from Polymer Materials Science and Engineering, 2006, 22(3): 199–203 (in Chinese)     

淀粉-醋酸乙酯-丙烯酸乙酯接枝共聚物

在硝酸铈铵(CAN)以及硫酸亚铁/过氧化氢两种引发体系中，进行了丙烯酸乙酯(EA)、醋酸乙烯酯(VAc)与玉米淀粉的接枝共聚。用质子核磁共振研究了接枝支链的化学组成、用X衍射研究接枝共聚物结晶结构的变化、用扫描电镜研究了材料的微观结构、并研究了共聚物的亲水性。制备了接枝淀粉、聚乙烯醇的生物降解塑料，测定了材料的力学性能以及疏水性。     

Graft Copolymerization on to Cellulose Using Binary Mixture of Monomers

The graft copolymerization of acrylonitrile (AN) and ethyl acrylate (EA) comonomers onto cellulose has been carried out using ceric ammonium nitrate (CAN) as an initiator in the presence of nitric acid at 35±0.1°C. The addition of ethyl acrylate as comonomer has shown a significant effect on overall and individual graft copolymerization of acrylonitrile on cellulose. The graft yield (%G_Y) and other grafting parameters viz. true grafting (%G_T), graft conversion (%C_G), cellulose number (Ng) and frequency of grafting (G_F) were evaluated on varying the concentration of comonomers from 6.0–30.0×10^?1 mol dm^?3 and ceric (IV) ions concentration from 2.5–25×10^?3 mol dm^?3 at constant feed composition (f_AN 0.6) and constant concentration of nitric acid (7.5×10^?2 mol dm^?3) in the reaction mixture. The graft yield (%G_Y) and other grafting parameters were optimal at 15×10^?1 mol dm^?3 concentration of comonomers and at 10×10^?3 mol dm^?3 concentration of ceric ammonium nitrate. The graft yield (%G_Y) and composition of grafted chains (F_AN) was optimal at a feed composition (f_AN) of 0.6. The energy of activation (Ea) for graft copolymerization has been found to be 16 kJ mol^?1. The molecular weight (Mw) and molecular weight distribution (Mw/Mn) of grafted chains was determined by GPC and found to be optimum at 15×10^?1 mol dm^?3 concentration of comonomer in the reaction mixture. The composition of grafted chains (F_AN) determined by IR method was used to calculate the reactivity ratios of monomers, which has been found to be 0.62 (r₁) and 1.52 (r₂), respectively for acrylonitrile (AN) and ethyl acrylate (EA) monomers used for graft copolymerization. The energy of activation for decomposition of cellulose and grafted cellulose was determining by using different models based on constant and different rate (β) of heating. Considering experimental observations, the reaction steps for graft copolymerization were proposed.     

Ethyl Acrylate‐Hydroxyethyl Acrylate and Hydroxyethyl Acrylate‐Methacrylic Acid: Reactivity Ratio Estimation from Cross‐linked Polymer Using High Resolution Magic Angle Spinning Spectroscopy

Solution free radical copolymerizations of hydroxyethyl acrylate/methacrylic acid (HEA/MAA) and ethyl acrylate/hydroxyethyl acrylate (EA/HEA) have been conducted in m‐xylene (60 wt% solvent level) over the temperature range of 70–130°C using tert‐butyl peroxybenzoate as initiator. High resolution magic angle spinning spectroscopy (HR–MAS) and 2D–NMR have been utilized to characterize the copolymer gel for copolymer composition. The reactivity ratio values have been determined from low conversion copolymer composition data using the computer software package RREVM, which is based on the error in variables model (EVM) method. Also, Arrhenius‐type reactivity ratio expressions have been developed that describe how reactivity ratios vary with temperature.