Au纳米粒子在有机溶剂中的电导行为

采用化学方法制备出粒径约10nm的Au纳米粒子,分别用十二、十四和十六烷基硫醇对Au粒子表面进行修饰,再溶入不同有机溶剂中,制备得到Au纳米粒子/氯仿和Au纳米粒子/甲苯溶液.测试了不同溶液的电导率随溶质浓度的变化规律,发现在整个浓度范围内存在一个临界浓度值.当溶质浓度低于临界浓度值时,溶液的电导率随溶质浓度的增加而迅速增加;而当溶质浓度超过临界浓度值时,溶液电导率的增加缓慢.在本文测试的浓度范围内,当Au纳米粒子分别被十二、十四和十六烷基硫醇修饰时,Au纳米粒子/氯仿溶液的临界浓度值分别约为11.22,7.96和5.47g/L.在相同浓度下,Au纳米粒子外面包裹的烷基硫醇的链长越短,其溶液的电导率越大.在整个浓度范围内,Au纳米粒子/氯仿溶液的电导率均高于Au纳米粒子/甲苯溶液的电导率.     

正、叔十二烷基硫醇在铜表面上自组装膜测试

研究了正、叔十二烷基硫醇在铜表面上的自组装及混合自组装成膜情况,并利用交流阻抗和极化曲线电化学方法测试了正、叔十二烷基硫醇在铜表面上自组装膜及混合自组装膜对铜的耐腐蚀性,考察了正十二烷基硫醇自组装膜质量与正十二烷基硫醇溶液的浓度及组装时间的关系。研究结果显示,混合自组装膜的质量及其对铜的耐腐蚀性比仅组装正或叔十二烷基硫醇均有很大的提高。     

铁表面自组装缓蚀功能膜的电化学阻抗谱研究

在铁表面自组装十四烷基胺膜.研究该膜在0.5 mol/LH2SO4溶液中对铁的缓蚀性能.电化学阻抗谱测试表明,随着组装时间的延长,缓蚀性能也随之增强,最大缓蚀效率为68.7%.而以十二烷基硫醇和十四烷基胺修饰的混合膜则更为致密、稳定,对铁的缓蚀能力也明显优于仅以十二烷基硫醇或十四烷基胺修饰的单一膜,其缓蚀效率可提高至78.2%.     

建立在硫醇分子电化学替换组装基础上的纳米粒子区域化组装

利用金基底电位变化时硫醇自组装膜的吸脱附性质, 通过改变基底电位和组装溶液, 用电化学方法在金基底上实现了传统自组装技术难以实现的硫醇分子的替换组装; 通过金基底的分区化设计, 用控制电位的组装技术在基底的不同微区内制备了不同末端官能团的硫醇及其衍生物自组装膜; 并在此基础上实现了纳米粒子的区域化组装.     

不同受限状态下链硫醇的非线性光学响应

以和频(SFG)振动光谱技术探测了正十二硫醇(DDT)在不同受限状态下的分子振动信号,包括金属基底上的自组装单层(SAM)分子,放置在二氧化硅基底上的表面DDT化的金纳米粒子以及金纳米粒子的甲苯溶液.在三种状态下都探测到了来自于DDT分子的振动光谱,振动光谱的区别提供了在不同受限态下DDT分子的结构信息.在金属基底上DDT分子排列规整,放置在二氧化硅基底上的金纳米粒子表面的DDT分子具有一定的柔性,在空气-甲苯溶液界面金纳米粒子表面的DDT分子高度无序.此外,光谱实验显示,金纳米粒子表面的分子振动信号产生了局域场增强的效应,相对于金基底上的自组装单层分子而言,增强系数为102-103,取决于光谱的偏振组合.     

Au-Ag三角纳米环单层膜的原位转化制备及 SERS效应

利用模板牺牲氧化还原反应将自组装在基片上的三角板银纳米粒子(边长约为79.2 nm)与氯金酸溶液作用进而原位转化形成三角纳米环. 通过紫外-可见(UV-Vis)光谱实时监测基片上银三角板纳米粒子在反应不同阶段的消光特性; 扫描电子显微镜(SEM)显示了银三角板纳米粒子转化过程的形貌变化; 利用X射线光电子能谱(XPS)对其成分进行分析. 表征结果表明, 三角纳米环的成分为Au-Ag合金或复合物; 随着基片与氯金酸溶液作用时间的增加, 自组装膜的表面等离子体共振峰逐渐红移; Au-Ag三角环状纳米粒子的平均壁厚度从29.3 nm缩小至16.2 nm. 以4-巯基苯胺(4-ATP)为探针分子研究了该Au-Ag三角环状纳米粒子单层膜的表面增强拉曼(SERS)活性. 自组装单层膜基底的SERS信号随着Au-Ag三角纳米环平均壁厚度的增加逐渐增强.     

二茂铁硫醇自组装膜的电化学行为及其离子对效应

详细了研究１０－二基铁－１－癸硫醇（ＨＳＣ１０Ｆｃ）在金基底上形成的自组装单分子膜的电化学行为,发现ＨＳＣ１０Ｆｃ在金基底上形成稳定的自组装膜,并且在０．１ｍｏｌ／Ｌ的ＨＣｌＯ４溶液中表现出可逆的氧化还原行为,但其氧化还原峰的峰形和峰位极易溶液中阴离子种类和浓度的影响,考察了二茂铁自组装膜及通过后置换形成的二茂铁硫醇／十二烷基硫醇混合膜在混合电解液中的电化学行为,直接比较了两种不同阴离子与二茂铁阳     

基底电位对硫醇自组装膜形成的影响

应用电位阶跃法,在不同组装电位下制备金/正十二硫醇自组装单分子膜.交流阻抗谱表征该硫醇膜的电化学性质,发现金基底的电位对硫醇自组装膜的形成有重要影响.在-0.8~-0.4 V的电位区间内,随着组装电位的增加,该自组装膜的致密性、有序性增加,缺陷减少,并于0.4 V时达到最佳.组装电位高于0.4 V,膜的致密性、有序性降低,缺陷增多.本文为硫醇及其衍生物的电位调控组装提供了重要依据.     

图案化自组装膜导向的电沉积

通过图案化自组装膜导向的电沉积制备了聚吡咯(PPy)微结构. 由微接触印刷方法制备图案化自组装膜并作为电沉积的模板. 研究发现, 自组装膜在导向电沉积中在不同的基底上具有不同的作用: 在十二烷基硫醇(DDT)、十八烷基硫醇(ODT)修饰的金基底上和十八烷基三氯硅烷(OTS)修饰的铟锡氧化物玻璃上(ITO), 电沉积主要发生在自组装膜未修饰区, 而在半导体单晶硅表面, PPy沉积在OTS修饰区, 是基底表面的导电性及PPy与基底表面基团相容性共同作用的结果.     

不同受限状态下链硫醇的非线性光学响应

以和频(SFG)振动光谱技术探测了正十二硫醇(DDT)在不同受限状态下的分子振动信号, 包括金属基底上的自组装单层(SAM)分子, 放置在二氧化硅基底上的表面DDT化的金纳米粒子以及金纳米粒子的甲苯溶液. 在三种状态下都探测到了来自于DDT分子的振动光谱, 振动光谱的区别提供了在不同受限态下DDT分子的结构信息. 在金属基底上DDT分子排列规整, 放置在二氧化硅基底上的金纳米粒子表面的DDT分子具有一定的柔性, 在空气-甲苯溶液界面金纳米粒子表面的DDT分子高度无序. 此外, 光谱实验显示, 金纳米粒子表面的分子振动信号产生了局域场增强的效应, 相对于金基底上的自组装单层分子而言, 增强系数为10²-10³, 取决于光谱的偏振组合.     

Self-assembled metal colloid films: two approaches for preparing new SERS active substrates

In this paper, we propose two new approaches for preparing active substrates for surface-enhanced Raman scattering (SERS). In the first approach (method 1), one transfers AgI nanoparticles capped by negatively charged mercaptoacetic acid from a AgI colloid solution onto a quartz slide and then deoxidizes AgI to Ag nanoparticles on the substrate. The second approach (method 2) deoxidizes AgI to Ag nanoparticles in a colloid solution and then transfers the Ag nanoparticles capped by negatively charged mercaptoacetic acid onto a quartz slide. By transfer of the AgI/Ag nanoparticles from the colloid solutions to the solid substrates, the problem of instability of the colloid solutions can largely be overcome. The films thus prepared by both approaches retain the merits of metal colloid solutions while they discharge their shortcomings. Accordingly, the obtained Ag particle films are very suitable as SERS active substrates. SERS active substrates with different coverages can be formed in a layer-by-layer electrostatic assembly by exposing positively charged surfaces to the colloid solutions containing oppositely charged AgI/Ag nanoparticles. The SERS active substrates fabricated by the two novel methods have been characterized by means of atomic force microscopy (AFM) and ultraviolet-visible (UV-vis) spectroscopy. The results of AFM and UV-vis spectroscopy show that the Ag nanoparticles grow with the increase in the number of coverage and that most of them remain isolated even at high coverages. Consequently, the surface optical properties are dominated by the absorption due to the isolated Ag nanoparticles. The relationship between SERS intensity and surface morphology of the new active substrates has been investigated for Rhodamine 6G (R6G) adsorbed on them. It has been found that the SERS enhancement depends on the size and aggregation of the Ag particles on the substrates. Especially, we can obtain a stronger SERS signal from the substrate prepared by method 1, implying that for the metal nanoparticles capped with stabilizer molecules such as mercaptoacetic acid, the in situ deoxidization in the film is of great use in preparing SERS active substrates. Furthermore, we have found that the addition of Cl- into the AgI colloid solution changes the surface morphology of the SERS active substrates and favors stronger SERS enhancement.     

Radiolytic synthesis and characterization of Ag-PVA nanocomposites

The Ag-PVA nanocomposites with different contents of inorganic phase were prepared by reduction of Ag⁺ ions in aqueous PVA solution by gamma irradiation followed by solvent evaporation. Optical properties of the colloidal solutions and the nanocomposite films were investigated using UV-vis spectroscopy. Structural characterization of the Ag nanoparticles was performed by TEM and XRD. Interaction of the Ag nanoparticles with polymer matrix and the heat resistance of the nanocomposites were followed by IR spectroscopy and DSC analysis. IR spectra indicated that Ag nanofiller interact with PVA chain over OH groups. The changes of heat resistance upon the increase of the content of inorganic phase are correlated to the adsorption of polymer chains on the surface of Ag nanoparticles.     

Electrochemistry of conductive polymers 39. Contacts between conducting polymers and noble metal nanoparticles studied by current-sensing atomic force microscopy

Electrical properties of contacts formed between conducting polymers and noble metal nanoparticles have been examined using current-sensing atomic force microscopy (CS-AFM). Contacts formed between electrochemically prepared pi-conjugated polymer films such as polypyrrole (PPy), poly(3-methylthiophene) (P3MeT), as well as poly(3,4-ethylenedioxythiophene) (PEDOT) and noble metal nanoparticles including platinum (Pt), gold (Au), and silver (Ag) have been examined. The Pt nanoparticles were electrochemically deposited on a pre-coated PPy film surface by reducing a platinum precursor (PtCl62-) at a constant potential. Both current and scanning electron microscopic images of the film showed the presence of Pt islands. The Au and Ag nanoparticles were dispersed on the P3MeT and PEDOT film surfaces simply by dipping the polymer films into colloid solutions containing Au or Ag particles for specified periods (5 to approximately 10 min). The deposition of Au or Ag particles resulted from either their physical adsorption or chemical bonding between particles and the polymer surface depending on the polymer. When compared with PPy, P3MeT and PEDOT showed a stronger binding to Au or Ag nanoparticles when dipped in their colloidal solutions for the same period. This indicates that Au and Ag particles are predominantly linked with the sulfur atoms via chemical bonding. Of the two, PEDOT was more conductive at the sites where the particles are connected to the polymer. It appears that PEDOT has better aligned sulfur atoms on the surface and is strongly bonded to Au and Ag nanoparticles due to their strong affinity to gold and silver. The current-voltage curves obtained at the metal islands demonstrate that the contacts between these metal islands and polymers are ohmic.     

A general phase transfer protocol for synthesizing alkylamine-stabilized nanoparticles of noble metals

The ethanol-mediated phase transfer protocol was extended herein to prepare alkylamine-stabilized nanoparticles of several noble metals by transferring them from aqueous environment into toluene. This method relies on the use of ethanol as a mediator to provide and maintain adequate contact between dodecylamine and metal nanoparticles during the transfer process and involves first mixing the metal hydrosols and an ethanol solution of dodecylamine and then extracting the dodecylamine-stabilized metal nanoparticles into toluene. Alkylamine-stabilized Ag, Pd, Rh, Ir and Os nanoparticles with 7.09, 3.45, 6.89, 2.42 and 4.52 nm in diameter, respectively, could be prepared this way. The self-assembly of dodecylamine-stabilized Ag and Rh nanoparticles was also detected by transmission electron microscopy (TEM).     

Fabrication, Characterization, and Surface-Enhanced Raman Activity Study of Silver Coated Gold Nanoparticulate Films

This paper reports a study on the preparation of Ag-clad Au colloidal monolayer films by a combination of colloid self-assembly and liquid phase microwave high-pressure technique. Firstly, monodisperse Au nanoparticles prepared by microwave heating method were assembled onto a quartz slide. Then, these Au colloidal particles on the quartz surface acted as seeds for growing the Ag-clad Au composite particulate films. The obtained particulate films were characterized by UV-Vis spectra and atomic force microscopy. It was found that the thickness of the shell and thus the size of particles in the composite colloidal films could be controlled by deposition of Ag on the preformed Au colloidal particle film in the microwave reaction system, and such films significantly increased the surface-enhanced Raman scattering enhancement （SERS） ability compared with Au colloidal particle films. Their strong enhancement ability may mainly stem from relatively large particle consisting of Ag cladding as well as effective coupling among particles in the Ag-clad Au particle ftlms.     

Electrochemical solid-state phase transformations of silver nanoparticles

Adenosine triphosphate (ATP)-capped silver nanoparticles (ATP-Ag NPs) were synthesized by reduction of AgNO(3) with borohydride in water with ATP as a capping ligand. The NPs obtained were characterized using transmission electron microscopy (TEM), UV-vis absorption spectroscopy, X-ray diffraction, and energy-dispersive X-ray analysis. A typical preparation produced ATP-Ag NPs with diameters of 4.5 ± 1.1 nm containing ~2800 Ag atoms and capped with 250 ATP capping ligands. The negatively charged ATP caps allow NP incorporation into layer-by-layer (LbL) films with poly(diallyldimethylammonium) chloride at thiol-modified Au electrode surfaces. Cyclic voltammetry in a single-layer LbL film of NPs showed a chemically reversible oxidation of Ag NPs to silver halide NPs in aqueous halide solutions and to Ag(2)O NPs in aqueous hydroxide solutions. TEM confirmed that this takes place via a redox-driven solid-state phase transformation. The charge for these nontopotactic phase transformations corresponded to a one-electron redox process per Ag atom in the NP, indicating complete oxidation and reduction of all Ag atoms in each NP during the electrochemical phase transformation.     

Interfacial deposition of Ag on Au seeds leading to AucoreAgshell in organic media

A seed mediated procedure for the synthesis of hydrophobic Au(core)Ag(shell) nanoparticles in toluene is demonstrated. The reaction proceeds by way of the interfacial reduction of silver ions by 3-pentadecylphenol followed by their deposition on hydrophobized Au nanoparticles. Such a hitherto unreported interfacial seeded growth reaction leads to the formation of phase pure Au(core)Ag(shell) nanoparticles that retain the hydrophobicity of the seed particles and remain stable in toluene. Such core-shell structures are however not formed in the aqueous phase. The core-shell architecture was verified using TEM analysis and the formation process was studied by recording the UV-vis spectra of the organic phase nanoparticles as a function of time. TEM kinetics also showed gradual increase in the silver layer thickness. Conclusive evidence was however obtained on examination of the HRTEM images of the products formed. Elemental analysis using X-ray photoelectron spectroscopy of the Au(core)Ag(shell) nanostructure revealed the presence of metallic silver. Moreover changing the surface capping of the Au seed does not affect the formation of the Au(core)Ag(shell) nanostructure.     

Direct precursor conversion reaction for densely packed Ag2S nanocrystal thin films

Successful realization of highly crystalline and densely packed Ag2S nanocrystal (NC) films has been achieved by directly converting precursor molecules, Ag(SCOPh), on preheated substrates. When an aliquot of Ag(SCOPh) solution dissolved in trioctylphosphine (TOP) is applied on preheated solid substrates at 160 degrees C, such as SiO2/Si, H-terminated Si, and quartz. Ag2S NC thin films have been formed with instant phase and color changes of the precursor solutions from pale yellow homogeneous solution to black solid films. The average diameter of individual Ag2S NCs forming thin films is ca. 25 nm, as confirmed by examining both isolated Ag2S NCs from thin films and as-made thin film samples by using transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. Powder X-ray diffraction (XRD) pattern shows that the synthesized Ag2S NCs have well-defined monoclinic acanthite phase. Direct precursor conversion process has resulted in densely packed Ag2S NCs with reduced interparticle distances owing to efficient removal of TOP during the reaction. Compared to the devices fabricated by the drop-coating process, Ag2S thin film devices fabricated by direct precursor conversion process have shown a ca. 300-fold increased conductance. Such Ag2S NC devices have also displayed reliable photoresponses upon white light illumination with high photosensitivity (S approximately equal to 1).     

Low-temperature preparation of highly conductive thin films from acrylic acid-stabilized silver nanoparticles prepared through ligand exchange

The preparation of AcA-stabilized Ag nanoparticles and its application to make highly conductive thin films are reported. The AcA-stabilized Ag nanoparticles were prepared through a ligand exchange of original oleylamine (OLA)-coated Ag nanoparticles with acrylic acid (AcA), which acted as both an antisolvent and a modifying ligand during the ligand exchange process. Efficiencies of the ligand exchange as well as the properties of Ag nanoparticles were analyzed using various techniques including TEM, FT-IR, XPS, TGA, and UV-vis methods. The thin films were fabricated by annealing spin-coated AcA-stabilized Ag nanoparticles. Further, the effects of annealing temperature, time, and film thickness on both the film morphology and electrical conductivity have been investigated. In this work, due to the low boiling temperature of stabilizer (AcA) and adjustment of annealing conditions, high electrical conductivity was obtained for the Ag thin films. For example, when annealing at 175 °C for 30 min, a 70 nm thick film showed a maximum electrical conductivity of 1.12 × 10(5) S cm(-1). A conductive layer on a flexible polymer substrate (e.g., PET) sheet has been successfully prepared by annealing a spin-coated film at 140 °C for 30 min. The combined advantages of long-term stability of the AcA-stabilized Ag nanoparticles, low annealing temperature, and high conductivity of the prepared thin films make this relatively simple method attractive for applications in flexible electronics.     

Investigations on silver/polyaniline electrodes for electrochemical supercapacitors

Polyaniline (PANI) and silver doped polyaniline (Ag/PANI) thin films were deposited on stainless steel substrates by a dip coating technique. To study the effect of doping concentration of Ag on the specific capacitance of PANI the concentration of Ag was varied from 0.3 to 1.2 weight percent. Fourier transform-infrared and Fourier transform-Raman spectroscopy, and energy dispersion X-ray techniques were used for the phase identification and determination of the doping content in the PANI films, respectively. The surface morphology of the films was examined by Field Emission Scanning Electron Microscopy, which revealed a nanofiber like structure for PANI and nanofibers with bright spots of Ag particles for the Ag/PANI films. There was decrease in the room temperature electrical resistivity of the Ag/PANI films of the order of 10(2) with increasing Ag concentration. The supercapacitive behavior of the electrodes was tested in a three electrode system using 1.0 M H(2)SO(4) electrolyte. The specific capacitance increased from 285 F g(-1) (for PANI) to 512 F g(-1) for Ag/PANI at 0.9 weight percent doping of Ag, owing to the synergic effect of PANI and silver nanoparticles. This work demonstrates a simple strategy of improving the specific capacitance of polymer electrodes and may also be easily adopted for other dopants.