V_2O_5纳米片固载Pt纳米粒子催化剂的构建及其增强催化空气氧化脱硫性能（英文）

以铂系金属为代表的贵金属催化剂在工业反应中通常表现出优异的催化性能,这是因为其具有独特的d带电子结构和较高的价电子比.近年来,由于大气排放法规愈发严苛,铂系贵金属催化剂在催化空气氧化燃油脱硫方面的研究引起了广泛关注.在该催化反应中,铂系金属纳米粒子可以有效活化空气中的氧气,产生的活性氧物种可以将油品中的噻吩类硫化物氧化为其对应的强极性砜类物质,从而可以将其从非极性的油品中分离出来,有效实现油品中硫化物的深度氧化脱除.然而,在反应过程中铂系贵金属纳米粒子易发生流失和烧结,从而导致催化剂的失活.因此,急需寻找一类可以有效固载铂系贵金属纳米粒子的载体.在目前已报道的众多载体中,以ZrO_2、TiO_2、CeO_2、ZnO等为代表的过渡金属氧化物引起了广泛的关注.通常认为,铂系贵金属纳米粒子的d轨道电子和过渡金属氧化物之间可形成金属-载体强相互作用.然而,目前所使用的过渡金属氧化物载体的比表面积较小,从而导致铂系贵金属纳米粒子难以有效且均匀地分散于其表面.本文采用热膨胀气相剥离法制备了超薄V_2O_5纳米片,并通过超声辅助沉积法将Pt纳米粒子固载于其表面,从而得到一系列可高效活化空气氧化脱硫的催化剂(Pt NPs-n/V_2O_5纳米片).通过电感耦合等离子体光谱、高倍透射电镜、原子力显微镜、X射线光电子能谱、X射线衍射、拉曼光谱和氮气吸附脱附等方法对催化剂的结构和形貌进行了表征.结果表明,尺寸为4–5 nm的Pt纳米粒子可有效均匀分散于层数约为6层的V_2O_5纳米片表面;在空气氧化脱硫反应中,当催化剂中Pt理论负载量为2 wt%时,反应5 h后,油品的脱硫率可达99.1%,实现了硫化物的深度氧化脱除.该反应体系对不同硫浓度、不同含硫底物的油品均有较好的脱除效果,但对含有烯烃、芳烃的油品脱除效果较差.此外,催化剂循环使用7次后,其脱硫活性仍无明显下降,表现出优异的重复使用性能.对反应后的催化剂进行表征,发现Pt几乎不发生流失,这可能是由于Pt纳米粒子和V2O5纳米片之间形成了金属-载体强相互作用.该结果为其他空气氧化反应的有效进行提供了新思路.     

多酸结构对纳米钛硅TS-1沸石催化氧化脱硫性能的影响

采用浸渍法合成了纳米钛硅TS-1沸石负载的钼系列多金属氧酸盐(POM)复合催化剂,采用扫描电子显微镜(SEM)、傅里叶红外光谱(FT-IR)、固体紫外漫反射(UV-Vis)、X-ray粉末衍射(XRD)、氮气吸附脱附(BET)、³¹P和²⁹Si魔角核磁共振(MAS-NMR)等对催化剂的结构进行表征。 研究结果表明,在低温焙烧或烘干条件下,负载后催化剂多酸的结构保持,钼酸铵高温(550 ℃)焙烧后转变为三氧化钼。 以有机硫化物噻吩(TH)、苯并噻吩(BT)和二苯并噻吩(DBT)的正辛烷溶液为模拟油品评价了催化剂的氧化脱硫性能。 实验结果表明,纳米TS-1沸石载体上不同结构多酸作为脱硫催化剂对硫化物的脱除活性顺序为:Keggin型Mo-POM＞Anderson型Mo-POM＞Dawson型Mo-POM＞Mo-金属氧化物。以上述负载的多酸为催化剂,在反应条件为:V(模拟油)=V(乙醇)=10.0 mL,m(催化剂)=0.2 g,n(H₂O₂)∶n(S)=10∶1,温度60 ℃,硫化物按照由易到难的脱除顺序为TH＞DBT＞BT,与常规的TS-1沸石或者多酸催化剂的脱除顺序存在明显差异。 这是纳米TS-1沸石对于有机硫分子氧化反应的择形效应和POM催化氧化脱硫的电子云密度影响综合作用的结果。 Keggin型Mo-POM催化剂具有良好的循环使用性能,是一类制备方法简单、催化活性高且稳定性好的绿色环保型催化剂。     

磷钼酸和钛硅纳米复合氧化物构筑高活性氧化脱硫催化剂

采用溶胶凝胶法合成了钛硅纳米复合氧化物(TiO₂-SiO₂),并以其为载体用原位合成技术或浸渍法负载Keggin结构磷钼酸(HPMo)制备了复合催化剂,使用扫描电子显微镜(SEM)、傅里叶红外光谱仪(FT-IR)、紫外可见光谱仪(UV-Vis)、X射线衍射光谱(XRD)和比表面分析仪(BET)等测试手段对催化剂的结构进行表征。 结果表明,采用原位法合成的催化剂为纳米粒子,纳米晶骨架内存在微孔和介孔共存的孔道结构。 原位合成技术或浸渍法制备的催化剂中HPMo保持Keggin骨架结构。以模拟油品(二苯并噻吩、苯并噻吩或噻吩的正辛烷溶液)的氧化脱硫为探针反应,在选定的条件下:硫含量为200.0 g/g的正辛烷溶液和无水乙醇各10.0 mL,反应温度60 ℃,催化剂质量0.15 g,n(H₂O₂)∶n(S)=5∶1,二苯并噻吩的脱除率高于96.0%,产物中硫含量低于10.0 μg/g。 在相同的实验条件下,受电子云密度的影响,脱硫由易到难的顺序为二苯并噻吩>苯并噻吩>噻吩。 催化剂循环使用4次后活性未见明显降低,是一类绿色的模型有机硫化物氧化脱除工艺用催化剂。     

纳米碳纤维载铂作为质子交换膜燃料电池阳极催化剂

采用化学还原法合成了微结构不同的纳米碳纤维(板式、鱼骨式、管式)载铂催化剂(分别记为Pt/p-CNF、Pt/f-CNF、Pt/t-CNF). 通过高分辨透射电镜(HRTEM)和X射线衍射(XRD)等分析技术对催化剂的微观结构进行了表征, 并利用循环伏安(CV)法分析了催化剂的电化学比表面积(ESA). 在此基础上, 制备了膜电极(MEA), 通过单电池测试了催化剂的电催化性能. 结果表明: 铂纳米粒子在不同的纳米碳载体上表现出不同的粒径, 在板式、鱼骨式和管式纳米碳纤维上的铂纳米粒子平均粒径分别为2.4、2.7和2.8 nm. 板式纳米碳纤维载铂催化剂作单电池阳极时表现出良好的电催化性能, 其对应的最高功率密度可达0.569 W·cm^-2, 高于鱼骨式纳米碳纤维载铂催化剂和管式纳米碳纤维载铂催化剂对应的最高功率密度(分别为0.550和0.496 W·cm^-2). 同时, 也制备了碳黑(Pt/XC-72)载铂催化剂. 相比于Pt/XC-72, 纳米碳纤维载体上的铂纳米颗粒有较小的粒径、较好的分散和较高的催化活性, 说明纳米碳纤维是质子交换膜燃料电池(PEMFCs)催化剂的良好载体.     

烟气中二噁英的催化降解*

催化降解是一种工业烟气的末端处理技术,该技术基于催化氧化还原反应能够实现烟气中二噁英（PCDD/Fs）在温和条件下的有效去除。目前研究较多的催化剂主要有两类：一类是Pt、Pd、Lr等贵金属型催化剂,另一类是V、Cr、W等过渡金属氧化物型催化剂。在实际应用方面,选择性催化还原（SCR）是目前最具有代表性的技术,采用V₂O₅/W(Mo)O₃-TiO₂催化剂能够同时脱除烟气中的PCDD/Fs和NO_x。本文阐述了贵金属和金属氧化物两种催化剂在温和条件下降解烟气中PCDD/Fs的反应机理和研究进展,并着重介绍了负载型V基催化剂降解PCDD/Fs的配方优化研究和影响因素,最后评述了SCR的应用情况和应用条件,以及在应用过程中催化剂的失活和中毒情况,并对该技术发展方向加以展望。     

Pt/MnO2纳米结构催化剂的制备与结构表征

采用一种简单的方法合成了Pt/MnO2纳米结构催化剂.通过改变还原时间、反应温度、聚乙烯吡咯烷酮（PVP）的用量、Pt负载量等,研究了反应条件对Pt/MnO2纳米结构催化剂的Pt纳米粒子的粒径大小、粒径分布和分散性影响.并在最佳条件下合成一系列不同载体和Pt负载量的Pt/MnO2纳米结构催化剂.通过X射线衍射（XRD）...     

核-壳结构多酸/磁性铈铁纳米复合氧化物@SiO2吸附-氧化脱硫性能

水热法合成了铈铁纳米复合氧化物,采用化学沉积法在其表面包裹SiO₂制备核-壳结构磁性材料,以其为载体负载H₂O₂结合Keggin结构磷钼酸(HPMo)制备了HPMo-H₂O₂/CeFe_xO_y@SiO₂吸附-氧化脱硫催化剂。 采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶红外光谱(FT-IR)、X射线粉末衍射(XRD)、氮气吸附脱附(BET)、³¹P魔角核磁共振(MAS-NMR)和X射线光电子能谱(XPS)等对催化剂的结构进行表征。 结果表明,SiO₂将CeFe_xO_y包裹形成核-壳结构纳米复合材料,以其为载体负载HPMo-H₂O₂后Keggin型多酸的骨架结构保持,并产生少量过氧化磷钼酸盐活性物种。 不同催化剂对有机硫化物二苯并噻吩(DBT)的吸附脱硫和氧化脱硫性能,均呈现出HPMo-H₂O₂/CeFe_xO_y@SiO₂＞CeFe_xO_y@SiO₂＞CeFe_xO_y的活性顺序,多酸的引入大大提升了其对大分子有机硫化物的吸附和氧化脱除性能,催化氧化脱硫活性的提高源于多酸分子“假液相”反应过程的结果。 在反应温度60 ℃,反应3 h,m(油)∶m(催化剂)=35∶1,n(O)∶n(S)=10∶1的条件下,对DBT氧化脱除率达到99.4%。 制备的磁性核-壳结构氧化脱硫剂有理想的氧化脱除DBT的循环使用性能,并且可通过外加磁场进行简单分离,是一类制备方法简单、催化活性高且稳定性好的绿色环保型催化剂。     

Al2O3孔结构对纳米HZSM-5基催化剂改质FCC汽油性能的影响

采用NH₃-TPD、FT-IR、N₂吸附-脱附等手段对两种不同来源的氧化铝样品进行了表征。结果表明,两种Al₂O₃的总酸量及酸强度没有明显差别,酸类型均以Lewis酸为主,其中,Al₂O₃ (b)的平均孔径及孔体积较大。在固定床微型反应装置上考察了以两种Al₂O₃为载体制备的纳米HZSM-5基催化剂改质全馏分FCC汽油的性能。实验结果表明,以大孔Al₂O₃为载体的HZSM-5基催化剂具有较好的降烯烃、芳构化、异构化活性及稳定性。改性纳米HZSM-5负载的LaNiMo催化剂对FCC汽油的300 h评价结果表明,烯烃饱和率为83%,脱硫率为87%,同时维持了油品的辛烷值。     

可见光诱导提升Pt/g-C3N4纳米片甲酸氧化性能的研究

以半导体材料类石墨氮化碳纳米片(g-C₃N₄纳米片)为载体,通过微波-多元醇法构筑了Pt/g-C₃N₄纳米片催化剂. 通过TEM、XRD、XPS、紫外-可见吸收光谱等方法对Pt/g-C₃N₄纳米片催化剂的粒径尺寸、组成、结构、光学等性质进行分析. 通过对比可见光照和暗室条件下的甲酸电氧化活性,Pt/g-C₃N₄纳米片催化剂在可见光照射下展现出良好的催化性能. 该性能的提高一方面可能是由于g-C₃N₄纳米片在可见光照射下加速了电子从Pt转移给g-C₃N₄纳米片,Pt处于“电子匮乏”状态,可削弱CO与Pt之间的化学键能,减弱CO在Pt表面的吸附能力,促进了CO的氧化,提高了催化剂抗中毒能力;另一方面,g-C₃N₄纳米片在光照条件下分离出的空穴可有效氧化甲酸分子,提高甲酸氧化活性. 因此,可见光条件下可有效提高Pt/g-C₃N₄纳米片催化剂甲酸催化氧化活性,这为直接甲酸燃料电池的发展提供了新思路.     

Pt/H-TiO2催化剂制备及其甲醇电催化氧化性能

以四氯化钛为前驱体,采用水热法合成二氧化钛纳米棒（TiO₂,白色）,在纯H₂气氛,将其550 ^oC热处理2 h,即得有氧缺陷和Ti³⁺填隙原子的二氧化钛纳米棒（H-TiO₂,灰黑色）. 将Pt纳米粒子（~ 1.9 nm）负载于此两种二氧化钛纳米棒上,制得Pt/TiO₂和Pt/H-TiO₂催化剂. XRD和XPS测试表明,氢处理TiO₂晶型没有变化,仍属金红石型,但增加了Ti-OH表面物种. 电化学测试表明,H-TiO₂载体能够增强氧在Pt表面的吸脱附能力,从而提高其甲醇电催化氧化活性,Pt/H-TiO₂电极甲醇氧化峰电流密度为Pt/TiO₂电极的1.6倍、Pt/C电极的2.1倍.     

Controllable Fabrication of Tungsten Oxide Nanoparticles Confined in Graphene‐Analogous Boron Nitride as an Efficient Desulfurization Catalyst

Tungsten oxide nanoparticles (WO_xNPs) are gaining increasing attention, but low stabiliity and poor dispersion of WO_xNPs hinder their catalytic applications. Herein, WO_xNPs were confined in graphene‐analogous boron nitride (g‐BN) by a one‐step, in situ method at high temperature, which can enhance the interactions between WO_xNPs and the support and control the sizes of WO_xNPs in a range of about 4–5 nm. The as‐prepared catalysts were applied in catalytic oxidation of aromatic sulfur compounds in which they showed high catalytic activity. A balance between the W loading and the size distribution of the WO_xNPs could govern the catalytic activity. Furthermore, a synergistic effect between g‐BN and WO_xNPs also contributed to high catalytic activity. The reaction mechanism is discussed in detail and the catalytic scope was enlarged.     

催化剂对CaO固硫反应活性的影响研究

用热天平研究了在CaO中添加不同催化剂对固硫反应进程及固硫反应转化率的影响,并采用等效粒子模型处理实验数据,计算了固硫反应两个阶段(表面化学反应控制阶段及产物层扩散控制阶段)的动力学参数。实验表明不同的催化剂对CaO固硫的影响效果和机制不同：催化剂KNO3,NaNO3使表面化学反应活化能和产物层扩散控制阶段反应活化能降低,但同时也使表面化学反应指前因子和扩散系数指前因子降低;而催化剂Fe2O,V2O5增大了表面化学活化能和产物层扩散控制阶段反应活化能,但同时也增大了表面化学反应指前因子和扩散系数指前因子。并发现几种催化剂对活化能和指前因子的影响都具有耦合性,因此单以表面化学反应活化能或产物层扩散控制阶段反应活化能来判断固硫反应活性是不够全面的,应计算出具体温度下的反应速率常数和产物层扩散系数值,才能准确地反映固硫反应的活性。     

Polydimethylsiloxane Coating for a Palladium/MOF Composite: Highly Improved Catalytic Performance by Surface Hydrophobization

Surface wettability of active sites plays a crucial role in the activity and selectivity of catalysts. This report describes modification of surface hydrophobicity of Pd/UiO‐66, a composite comprising a metal–organic framework (MOF) and stabilized palladium nanoparticles (NPs), using a simple polydimethylsiloxane (PDMS) coating. The modified catalyst demonstrated significantly improved catalytic efficiency. The approach can be extended to various Pd nanoparticulate catalysts for enhanced activity in reactions involving hydrophobic reactants, as the hydrophobic surface facilitates the enrichment of hydrophobic substrates around the catalytic site. PDMS encapsulation of Pd NPs prevents aggregation of NPs and thus results in superior catalytic recyclability. Additionally, PDMS coating is applicable to a diverse range of catalysts, endowing them with additional selectivity in sieving reactants with different wettability.     

Aerobic oxidation of benzyl alcohols through biosynthesized palladium nanoparticles mediated by Oak fruit bark extract as an efficient heterogeneous nanocatalyst

In this study, green synthesis of Pd nanoparticles (NPs) is outlined through application of Oak fruit bark extract as a reducing, capping and stabilizing agent. The characteristics and properties of the biosynthesized Pd NPs were revealed by FESEM, EDX, XRD, TEM, UV–Vis, and FT-IR spectroscopies. So that, UV–Vis spectroscopy of the Pd colloidal solution confirmed reduction of Pd ions, and XRD and TEM analysis identified fcc unit cell structure forming 5–7 nm spherical Pd NPs. Furthermore, catalytic activity of the prepared catalyst was investigated through aerobic oxidation of alcohols, as model reactions. Catalytic evaluations demonstrated achievement of good yields from primary and secondary benzyl alcohols. In general, the devised synthesis method is advantageous from several perspectives. For example, the synthesized catalysts give high product yields and are efficient, they eliminate the need for surfactant, chemical reductants, ligand and organic solvents, the approach is economically inexpensive, it results in cleaner reaction profiles, application of the simply prepared heterogeneous catalyst is convenient, and the catalyst is recoverable and reusable for at least six times without any significant loss of its catalytic activity.     

Deep desulfurization by oxidation using an active ionic liquid‐supported Zr metal–organic framework as catalyst

In this study, a Zr metal–organic framework (UIO‐66) was synthesized with zirconium tetrachloride and terephthalic acid using the solvent method. Then various masses of 1‐methylimidazolium‐3‐propylsulfonate hydrosulfate (PSMIMHSO₄) were supported on the UIO‐66 as catalysts, which were used for catalytic oxidative desulfurization. Sulfur removal using 400 mg of 40% PSMIMHSO₄ supported on the UIO‐66 of greater than 94% was obtained at 313 K for 20 min with an O/S molar ratio of 7:1. The results obtained in this work could provide useful information for the design of water‐stable metal–organic frameworks with permanent porosity in applications of catalytic oxidative desulfurization. Copyright © 2014 John Wiley & Sons, Ltd.     

Metal–Support Cooperative Catalysts for Environmentally Benign Molecular Transformations

Metal–support cooperative catalysts have been developed for sustainable and environmentally benign molecular transformations. The active metal centers and supports in these catalysts could cooperatively activate substrates, resulting in high catalytic performance for liquid‐phase reactions under mild conditions. These catalysts involved hydrotalcite‐supported gold and silver nanoparticles with high catalytic activity for organic reactions such as aerobic oxidation, oxidative carbonylation, and chemoselective reduction of epoxides to alkenes and nitrostyrenes to aminostyrenes using alcohols and CO/H₂O as reducing reagents. This high catalytic performance was due to cooperative catalysis between the metal nanoparticles and basic sites of the hydrotalcite support. To increase the metal–support cooperative effect, core–shell nanostructured catalysts consisting of gold or silver nanoparticles in the core and ceria supports in the shell were designed. These core–shell nanocomposite catalysts were effective for the chemoselective hydrogenation of nitrostyrenes to aminostyrenes, unsaturated aldehydes to allyl alcohols, and alkynes to alkenes using H₂ as a clean reductant. In addition, these solid catalysts could be recovered easily from the reaction mixture by simple filtration, and were reusable with high catalytic activity.     

Efficient catalytic performance of tetra-alkyl orthotitanates for the oxidative desulfurization of dibenzothiophene at room temperature

Desulfurization of fuel oil is of great importance for producing clean energy. In this study, we report that tetra-alkyl orthotitanates exhibited efficient catalytic performance in the oxidative desulfurization of dibenzothiophene. The sulfur content in model oil (1000 ppmw) could be reduced to less than 10 ppmw within 10 min at room temperature and ambient pressure. In addition, the formed sulfones can be easily separated from the oil phase without extraction process. This work will provide a basis for the design of novel oxidative desulfurization catalysts with high desulfurization efficiency.     

Delivery of Highly Active Noble‐Metal Nanoparticles into Microspherical Supports by an Aerosol‐Spray Method

Noble metal nanoparticles (NPs) with 1–5 nm diameter obtained from NaHB₄ reduction possess high catalytic activity. However, they are rarely used directly. This work presents a facile, versatile, and efficient aerosol‐spray approach to deliver noble‐metal NPs into metal oxide supports, while maintaining the size of the NPs and the ability to easily adjust the loading amount. In comparison with the conventional spray approach, the size of the loaded noble‐metal nanoparticles can be significantly decreased. An investigation of the 4‐nitrophenol hydrogenation reaction catalyzed by these materials suggests that the NPs/oxides catalysts have high activity and good endurance. For 1 % Au/CeO₂ and Pd/Al₂O₃ catalysts, the rate constants reach 2.03 and 1.46 min^?1, which is much higher than many other reports with the same noble‐metal loading scale. Besides, the thermal stability of catalysts can be significantly enhanced by modifying the supports. Therefore, this work contributes an efficient method as well as some guidance on how to produce highly active and stable supported noble‐metal catalysts.     

Water-soluble palladium nanoparticles as an active catalyst for highly selective hydrogenation of nitrobenzene to aniline

Palladium (Pd) nanoparticles (NPs) stabilized by tri-block copolymer polyoxyethylene–polyoxypropylene–polyoxyethylene (P123) micelles were synthesized in water using a hydrogenation reduction method. Well-dispersed P123 micelles in the aqueous phase favored the stabilization of Pd NPs. The P123–Pd micellar catalyst was first applied in the liquid phase hydrogenation of nitrobenzene (NB), showing excellent catalytic activity, and the only reaction product detected was aniline (AN). Using water as the reaction medium and under mild conditions, both the preparation of catalysts and NB hydrogenation were convenient and environmentally friendly. Under the optimal conditions, the isolated catalyst phase could be recycled at least five times, and the catalytic activity and selectivity remained unchanged. A reaction scheme was suggested. First-order kinetics was determined at 3.0 MPa hydrogen pressure and temperature 30–75 °C, and the activation energy was 40.18 kJ mol^?1. This work provides an environmentally benign and effective method for the hydrogenation of NB to AN.