LaNiO3/TiO2纳米管阵列的电化学制备及其光催化性能

利用脉冲电沉积与高温退火相结合的方法制备了镍酸镧(LaNiO₃)纳米颗粒负载的二氧化钛(TiO₂)纳米管阵列. 修饰于TiO₂纳米管阵列上的LaNiO₃纳米颗粒粒径小（< 10 nm）、分布均匀、负载量可控,一些LaNiO₃纳米颗粒沉积于TiO₂纳米管内. 紫外可见吸收光谱显示,LaNiO₃/TiO₂纳米管阵列的吸收带边较TiO₂纳米管阵列明显红移,可见光吸收明显增强. 可见光下光催化降解罗丹明B（RhB）的结果表明,脉冲循环沉积500次制得的LaNiO₃/TiO₂纳米管阵列的光催化活性最佳,其对RhB光催化降解速率是TiO₂纳米管阵列的3.5倍,并且表现出极好的光催化稳定性.     

TiO2/石墨烯复合材料的光生电荷分离调控与光催化产氢性能研究

半导体光生电荷分离是光催化过程中的关键步骤之一,其效率极大地影响了最终光催化性能.将TiO₂纳米片与石墨烯复合,能够促进TiO₂中光生电子和空穴的分离,从而提高其光催化活性.为了研究光生电荷的分离对TiO₂/石墨烯复合材料光催化性能的影响,通过调控TiO₂纳米片的尺寸来调节TiO₂/石墨烯复合材料中光生电荷分离的能力,然后研究其对TiO₂/石墨烯复合材料光催化性能的影响.合成了一系列不同厚度的TiO₂纳米片,将其与石墨烯复合,并通过光沉积负载Pt纳米颗粒作为助催化剂,用于光催化产氢.实验结果显示,随着TiO₂纳米片厚度减小,其与石墨烯形成的复合结构的光催化性能显著提高.这主要是由于TiO₂纳米片厚度减小时,光生电子沿厚度方向穿过TiO₂纳米片迁移到石墨烯的距离缩短,从而减少了光生电子在迁移过程中与空穴的复合;同时TiO₂纳米片厚度减小使其比表面积增大,使得TiO₂/石墨烯界面面积增大,从而使石墨烯更好地分离出TiO₂中的光生电子,有更多的光生电子到达石墨烯参与催化反应,提高TiO₂/石墨烯复合材料的光催化性能.此研究表明通过控制TiO₂纳米片的尺寸来调控TiO₂/石墨烯复合材料中光生电子和空穴的分离,是显著提高其光催化性能的有效途径.     

Ag/TiO2中空纳米纤维光催化材料的制备及表征

以棉花纤维为模板制备了银掺杂的TiO₂中空纳米纤维光催化材料, 利用热重分析(TG)、扫描电子显微镜(SEM)、X光电子能谱(XPS)、X射线衍射(XRD)、Zeta电位、紫外-可见光谱(UV-Vis)和傅立叶变换红外光谱(FT-IR)等技术对该材料的形貌、晶体结构、银的状态等特性进行了表征. 以亚甲基蓝(MB)的脱色降解为模型反应, 考察了银掺杂的样品Ag/TiO₂在不同光源下的光催化性能. 结果表明, 所制得的Ag/TiO₂材料保留了棉花纤维的形貌, 且表面带有大量的负电荷|该Ag/TiO₂材料在太阳光条件下的光催化性能显著高于同条件下TiO₂和同材料在紫外光条件下的, 如Ag/TiO₂在太阳光下1.5 h可使MB溶液的脱色降解率在95%以上, 在TiO₂上2.5 h时不足60%, 低于Ag/TiO₂上0.5 h的结果|在紫外光条件下Ag/TiO₂ 3 h时脱色降解率仅为35%. 连续重复使用5次时Ag/TiO₂仍能保证MB溶液的脱色降解率在90%以上|该纤维光催化材料易于离心分离去除、再利用. 因此, 以棉花为模板制备的Ag/TiO₂中空纳米纤维催化材料是一种无能耗、无污染、高活性的绿色环保型光催化材料.     

TiO2光催化还原CO2

光催化还原CO₂技术在CO₂的治理与利用方面有着潜在的应用价值和良好的开发前景。该文简要综述了近年来用于光催化还原CO₂反应的TiO₂光催化剂材料,包括纯TiO₂催化剂、负载型TiO₂催化剂、金属改性TiO₂催化剂、半导体复合TiO₂催化剂和有机光敏化TiO₂催化剂等,并介绍了各类催化剂光催化还原CO₂的反应性能。     

高度有序的二氧化钛纳米管阵列的制备及其光催化活性的研究

采用电化学阳极氧化法在钛表面构筑了一种结构有序、微米级的TiO₂纳米管阵列膜层. 考察了制备电压、氧化时间、溶液搅拌等实验参数对TiO₂纳米管阵列形貌和尺寸的影响. 应用SEM和XRD对膜层的形貌和晶型进行了分析和表征, 并通过TiO₂纳米管阵列膜对甲基橙的光催化降解, 研究了TiO₂纳米管阵列膜层结构与光催化活性的关系. 结果表明: 阳极电压和溶液搅拌对制备TiO₂纳米管阵列的结构起到关键的作用. 控制20 V电压制备的TiO₂纳米管阵列膜, 管长达2.6～3.3 μm, 经500 ℃热处理后具有最高的光催化活性, 其光催化性能明显优于一般的TiO₂纳米颗粒膜.     

花状CeO2/TiO2异质结的构筑及光催化性能

采用溶剂热法制备了三维花状CeO₂/TiO₂异质结光催化剂,然后以甲基橙(MO)为模拟有机污染物,在氙灯照射下考察了其光催化活性。结果表明,花状结构由纳米片和纳米颗粒复合而成,纳米片上均匀地附着CeO₂颗粒。Ce/Ti的物质的量之比(n_Ce/n_Ti)和溶剂热时间影响异质结的光催化性能,当n_Ce/n_Ti=0.1、溶剂热时间为6 h时,CeO₂/TiO₂的光催化活性达到最佳,氙灯照射50 min的降解率达95%,光催化活性优于纯TiO₂,这主要是CeO₂和TiO₂形成了异质结,有利于光生电子和空穴的分离。     

CeO2/TiO2复合纳米纤维的制备及光催化性能研究

采用静电纺丝技术和水热合成法制备了CeO₂/TiO₂复合纳米纤维. 利用X射线衍射(XRD)、拉曼光谱(Raman)、扫描电镜(SEM)、透射电镜(TEM)和比表面积测定(BET)等分析测试手段对样品的形貌及结构进行了表征, 并以罗丹明B的脱色降解为模式反应, 考察了样品的光催化性能. 结果表明: CeO₂纳米粒子均匀地生长在TiO₂纳米纤维表面, 形成了异质结构的CeO₂/TiO₂复合纳米纤维光催化材料. 通过改变碱源, 可以得到不同形貌的CeO₂. CeO₂的存在增加了TiO₂纳米纤维的比表面积, 有效地实现TiO₂光生电子和空穴的分离, 增强了体系的量子效率, 与纯TiO₂纳米纤维相比光催化活性明显提高. 初步探讨了异质结的形成机理.     

TiO2纤维的制备及其光催化活性研究

K₂Ti₄O₉纤维为前驱体经过离子交换合成纤维TiO₂.通过甲基橙废水模型体系考察了纤维TiO₂的光催化活性,同时研究了在不同pH值条件下TiO₂纤维分散体系的稳定性能.结果表明,TiO₂纤维光催化活性与微米级TiO₂相当,且控制溶液的pH值可实现TiO₂纤维与溶液的快速分离.     

TiO2-CeO2光催化吸附协同脱除柴油中的有机硫

采用共沉淀法制备TiO₂-CeO₂光催化吸附脱硫材料,通过低温N₂吸附脱附和X射线衍射等技术对TiO₂-CeO₂的物理化学性质进行了表征。结果表明,紫外光辐射显著提高了TiO₂-CeO₂的吸附脱硫性能;柴油中有机硫在TiO₂-CeO₂表面发生了光催化氧化转化为极性较强的砜类,可选择性地吸附在材料表面而被脱除。当TiO₂-CeO₂材料中钛铈物质的量比为9：1、煅烧温度为500℃时,其光催化吸附协同脱硫效果最好;在紫外光辐射下反应5 h,油品中DBT的脱除率高达99.6%。TiO₂-CeO₂光催化吸附协同脱硫工艺可有效解决吸附脱硫工艺中芳烃竞争吸附导致吸附脱硫选择性低的问题;在模拟油品中添加质量分数为25%的甲苯,反应7 h后油品脱硫率仍高达96.6%。TiO₂-CeO₂对不同硫化物的光催化吸附协同脱硫效果顺序为：4,6-DMDBT> DBT> BT。TiO₂-CeO₂经四次再生循环使用后,脱硫率没有明显降低。     

固定在氧扩散膜表面的TiO2光催化膜

本文提出用氧扩散膜作TiO₂光催化膜的载体,介绍了氧扩散膜的制备及TiO₂在氧扩散膜表面的固定方法,TiO₂光催化膜的表面形态与微结构,不同条件下光催化分解草酸的速度.研究结果表明,以氧扩散膜作载体的TiO₂光催化薄膜表现出了较高的光催化活性.文中详细分析了氧扩散膜的作用.     

Furyl- and thienyl-silatranes and germatranes

We review our research on the synthesis and study of the physical and biological properties of furyl- and thienylgermatranes and -silatranes.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 6, pp. 725–732, June, 1992.     

Review and patents and literature

The use of the insect cell/baculovirus expression system for producing recombinant proteins of bacterial, plant, insect, and mammalian origin has become widespread. The popularity of this eukaryotic expression system is due to many factors, including (1) potentially high protein expression levels, (2) ease and speed of genetic engineering, (3) ability to accommodate large DNA inserts, (4) protein processing similar to higher eukaryotic cells (e.g., mammalian cells), and (5) ease of insect cell growth (e.g., suspension growth). The following review of the literature discusses two engineering aspects of recombinant protein synthesis by insect cell cultures: bioreactor scale-up and insect cell line selection. Following this review patent abstracts and additional literature pertaining to expression of recombinant proteins in insect cell culture are listed.     

Ground- and excited-state aromaticity and antiaromaticity in benzene and cyclobutadiene

The aromaticity and antiaromaticity of the ground state (S 0), lowest triplet state (T 1), and first singlet excited state (S 1) of benzene, and the ground states (S 0), lowest triplet states (T 1), and the first and second singlet excited states (S 1 and S 2) of square and rectangular cyclobutadiene are assessed using various magnetic criteria including nucleus-independent chemical shifts (NICS), proton shieldings, and magnetic susceptibilities calculated using complete-active-space self-consistent field (CASSCF) wave functions constructed from gauge-including atomic orbitals (GIAOs). These magnetic criteria strongly suggest that, in contrast to the well-known aromaticity of the S 0 state of benzene, the T 1 and S 1 states of this molecule are antiaromatic. In square cyclobutadiene, which is shown to be considerably more antiaromatic than rectangular cyclobutadiene, the magnetic properties of the T 1 and S 1 states allow these to be classified as aromatic. According to the computed magnetic criteria, the T 1 state of rectangular cyclobutadiene is still aromatic, but the S 1 state is antiaromatic, just as the S 2 state of square cyclobutadiene; the S 2 state of rectangular cyclobutadiene is nonaromatic. The results demonstrate that the well-known "triplet aromaticity" of cyclic conjugated hydrocarbons represents a particular case of a broader concept of excited-state aromaticity and antiaromaticity. It is shown that while electronic excitation may lead to increased nuclear shieldings in certain low-lying electronic states, in general its main effect can be expected to be nuclear deshielding, which can be substantial for heavier nuclei.     

多环芳二酐型聚酯亚胺膜的透气性能

多环芳二酐型聚酯亚胺膜的透气性能李悦生，丁孟贤，徐纪平（浙江大学高分子科学与工程研究所，杭州，３１００２７）（中国科学院长春应用化学研究所）关键词聚醚酰亚胺，聚酯酰亚胺，膜，透气性通常的聚酰亚胺加工性能较差，在芳环二酐的苯环间引入醚键等柔性基团后，其...     

Determination and study on residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil

A QuEChERS (quick, easy, cheap, effective, rugged, and safe) method for the determination of benazolin-ethyl and quizalofop-p-ethyl in rape and soil by high-performance liquid chromatography-tandem mass spectrometry has been developed in this study. The residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil were determined with the developed method. The half-lives of benazolin-ethyl in rape straw and soil were 3.7–5.1 days and 14.3–26.3 days, respectively. The half-lives of quizalofop-p-ethyl in rape straw and soil were 5.0-6.1 days and 0.3–9.7 days, respectively. The residue of benazolin-ethyl and quizalofop-p-ethyl in rapeseed and soil were below the detection limit (i.e., 0.5?mg?kg^?1, the maximum residue level of European Union for quizalofop-p-ethyl).     

Syntheses and structures of P-anilino-P-chalcogeno- and P-anilino-P-iminodiazasilaphosphetidines and their group 12 and 13 metal compounds

The P-anilino-P-chalcogeno(imino)diazasilaphosphetidines [Me(2)Si(mu-N(t)Bu)(2)P=E(NHPh)] (E = O (3), S (4), Se (5), N-p-tolyl (6)) were synthesized by oxidizing the P-anilinodiazasilaphosphetidine [Me(2)Si(N(t)Bu)(2)P(NHPh)] (2) with cumene hydroperoxide, sulfur, selenium, and p-tolyl azide, respectively. The lithium salt of 4 reacted with thallium monochloride to produce ([Me(2)Si(mu-N(t)Bu)(2)P=S(NPh)-kappaN-kappaS]Tl)(7), which features a two-coordinate thallium atom. Treatment of 4-6 with AlMe(3) gave the monoligand dimethylaluminum complexes ([Me(2)Si(mu-N(t)Bu)(2)P=E(NPh)-kappaN-kappaE]AlMe(2)) (E = S (8), Se (9), N-p-tolyl (10)), respectively. In these complexes the aluminum atom is tetrahedrally coordinated by one chelating ligand and two methyl groups, as a single-crystal X-ray analysis of 8 showed. A 2 equiv amount of 4-6 reacted with diethylzinc to produce the homoleptic diligand complexes ([Me(2)Si(mu-N(t)Bu)(2)P=E(NPh)-kappaN-kappaE](2)Zn)(E = S (11), Se (12), N-p-tolyl (13)). A crystal-structure analysis of 11 revealed a linear tetraspirocycle with a tetrahedrally coordinated, central zinc atom.