过渡金属添加剂对煤热解脱硫的影响

利用坩埚焦考察了过渡金属添加剂Fe、Cr和Mn的不同形态在焦化过程中对高硫焦煤中硫脱除的影响,并通过固定床热解实验考察了不同气氛下添加剂对煤热解脱硫及含硫化合物逸出的影响。结果表明,不同金属添加剂对煤中硫形态有不同影响,氧化性较高的Fe3+降低了煤中黄铁矿硫的含量,而其他金属添加剂对煤中硫形态影响不大。在模拟焦化过程中,铬系添加剂提高了热解脱硫率,而铁系和锰系添加剂降低了脱硫率;负载Cr3+的介休煤在不同气氛下的热解表明,氮气抑制了Cr的脱硫作用,显著地减少了含硫气体的生成量,并使煤中易脱除硫转化为稳定的有机硫;还原性气氛有利于Cr3+添加剂的脱硫作用,显著地增加了含硫气体的生成量;焦炉气和氢气下添加剂对热解脱硫及煤热解过程中含硫气体逸出的影响相似,焦炉气可以作为提高过渡金属添加剂脱硫性能的反应气体。     

MoO3/介孔Al2O3催化氧化脱除模拟油中的硫

以环己烷为溶剂,二苯并噻吩（DBT）、苯并噻吩（BT）、4,6-二甲基二苯并噻吩（4,6-DMDBT）、噻吩（Th）作为模型含硫化合物配制成模拟油,在MoO3/介孔Al2O3-H2O2体系中对模拟油催化氧化脱硫进行了研究. 考察了MoO3负载量、氧化剂用量、催化剂用量、氧化反应温度及反应时间对DBT脱除效果的影响. 实验结果表明：在MoO3负载量为20%,催化剂用量为1.5%,氧化剂H2O2与模拟油中硫的摩尔比为4,反应温度为60℃,反应时间为40分钟时DBT脱除率最高,达99.4%,几乎可以被完全脱除;在此条件下模型化合物的氧化反应活性顺序为：DBT > 4,6-DMDBT >BT>Th.     

金属盐对轻质油品氧化脱硫效果的影响

过氧化氢与低分子醛的氧化体系可以氧化脱除轻质油品中的部分硫,金属盐作为助剂有利于提高油品的脱硫率,尤其对硫醇硫和硫醚硫的脱除。以氧化法分别对三种类型硫-硫醇硫、硫醚硫和噻吩硫的模拟轻质油品进行脱硫实验,并考察四种不同金属盐的助脱硫效果,研究发现助剂SnCl4的作用最为显著。本文还考察了助剂的不同加入比例对脱硫率的影响,结果表明,硫醚硫的脱硫率与SnCl4加入量的大小正比关系比较明显;硫醇硫仅表现于脱臭率的增加;噻吩的硫原子参与芳香环共轭,与金属离子较难络合,因此助剂的加入对其脱除并没有明显效果。     

高硫煤加氢热解脱硫的研究Ⅱ.反应条件对煤加氢热解脱硫的影响

本文采用红庙褐煤在加压固定床上，详细考察了不同反应条件对加氢热解脱硫的影响。研究结果表明：氢气流速的增加可以显著降低焦中的硫含量，增加脱硫率和硫在气相中的分布。氢气压力增加有利于增加煤中含硫化合物的加氢脱硫反应，提高脱硫率。加氢热解过程中的传质作用对脱硫率和硫分布也有重要影响。在一定的热解温度下，适当增加停留时间有利于氢气与含硫化合物的扩散接触，提高脱硫率。同时红庙煤加氢热解产生的焦油中的硫分布随各种反应条件的变化不大。     

助剂镍/钴对磷化钨催化剂加氢精制性能的影响

在共浸渍法制备磷化钨／γ-Al2O3催化剂基础上，分别加人1％、3％、5％、7％和9％(占活性组分比例)的助剂镍或钴，制得负载30％含助剂镍／钴磷化钨／γ-Al2O3系列催化剂，考察了助剂及其加人比例对催化剂加氢脱硫和加氢脱氮性能的影响．结果表明，加人适当比例的助剂镍或钴，有利于提高磷化钨／γ-Al2O3催化剂的加氢脱硫活性，当助剂含量分别为5％镍或7％钴时，催化剂的噻吩加氢脱硫率最高；助剂镍对磷化钨／γ-Al2O3催化剂的加氢脱氮反应不利，而加人适当比例助剂钴有利于提高催化剂加氢脱氮活性，当助剂钴含量为5％时，催化剂吡啶加氢脱氮率最高．温度对磷化钨／γ-Al2O3催化剂加氢精制性能有一定影响，高温有利于加氢脱硫反应，低温有利于加氢脱氮反应．     

过氧磷钨酸催化氧化脱除模拟油中的含硫化合物

考察了以H₂O₂为氧化剂, 过氧磷钨酸为催化剂催化氧化脱除模拟油中的含硫化合物苯并噻吩(BT)和二苯并噻吩(DBT). 讨论了催化剂用量、反应温度、反应时间和剂油体积比等因素对反应的影响. 实验结果表明, 当催化剂用量为0.48%(质量分数), V(H₂O₂)∶V(Oil)=1∶50, 反应时间为60 min, 反应温度为60 ℃时, BT的脱除率达到96.48%, DBT的脱除率达到99.42%. 动力学研究结果表明, 过氧磷钨酸为催化剂的氧化脱除模拟油中的含硫化合物的反应为表观一级反应.     

脱硫废水蒸发增强电除尘脱除PM2.5和SO3实验研究

搭建燃煤热态实验系统,研究脱硫废水蒸发对电除尘和脱硫系统的影响;考察脱硫废水蒸发前后细颗粒粒径的变化、电除尘出口PM_2.5和SO₃浓度变化;分析增强电除尘脱除PM_2.5和SO₃机理。结果表明,脱硫废水蒸发后,蒸发室出口细颗粒粒径峰值由0.1 μm增大到1.1 μm,观察脱硫废水蒸发前后扫描电镜,明显观察到废水蒸发后颗粒团聚长大,颗粒间存在絮状物;采用脱硫废水烟道蒸发后,电除尘细颗粒脱除效率提高5%左右,PM_2.5数量浓度脱除效率提高25%左右;SO₃脱除效率为60%-80%,烟气中SO₃浓度对增强电除尘脱除PM_2.5和SO₃均有影响;脱硫废水蒸发对脱硫系统的效率和脱硫浆液的pH值没有影响。     

C_9H_(10)O_2-0.5ZnCl_2/Al_2O_3的制备及其氧化脱硫性能

通过将C_9H_(10)O_2-0.5ZnCl_2双酸型低共熔溶剂固载到Al_2O_3上制备了C_9H_(10)O_2-0.5ZnCl_2/Al_2O_3催化剂。该催化剂采用XRD、FT-IR、SEM、EDS、N_2吸附-脱附技术进行了分析。以C_9H_(10)O_2-0.5ZnCl_2/Al_2O_3为催化剂,过氧化氢为氧化剂研究模拟油中芳香族硫化物的脱除性能。考察反应参数如温度、催化剂加入量、O/S物质的量比、硫化物类型等对催化剂脱硫活性的影响。实验结果表明,在模拟油为5 mL、催化剂量为0.2 g、O/S比为8、反应温度为60℃、反应时间为180 min的条件下,模拟油中二苯并噻吩(DBT)脱硫率为99.2%。此外,在模拟油氧化脱硫中催化剂循环使用六次,其氧化脱硫活性略有降低。研究了C_9H_(10)O_2-0.5ZnCl_2/Al_2O_3催化氧化脱硫的反应机理。     

改性NaY分子筛吸附模拟油中噻吩的研究

用静态吸附方法研究了CuY分子筛、CeY分子筛和CeCuY分子筛对3种含噻吩的模拟油的吸附。实验结果表明,在相同条件下,以上3种分子筛对模拟油A、B的脱硫率为95%左右,对含环己烯的模拟油C的脱硫率均低于63%。运用BET对分子筛孔结构进行表征和运用IR对吸附模拟油后的分子筛情况进行考察,分析结果表明,Cu和Ce离子交换后的分子筛,BET比表面积下降,微孔比表面积下降,由此影响对模拟油A、B中噻吩的吸附。IR谱图表明,以上3种分子筛都会吸附环己烯,是导致其对模拟油C脱硫率下降的主要原因。     

Ti-MWW分子筛催化叔丁基过氧化氢氧化脱硫

以Ti-MWW为催化剂,考察了不同氧化剂对分别含有苯并噻吩、二苯并噻吩和4,6-二甲基二苯并噻吩等有机硫化物模拟油品氧化反应的影响,结果表明,叔丁基过氧化氢对有机含硫化合物的氧化活性明显高于过氧化氢水溶液。以叔丁基过氧化氢为氧化剂,三种噻吩类含硫化合物氧化的难易顺序为二苯并噻吩> 4, 6-二甲基二苯并噻吩> 苯并噻吩,其氧化活性顺序与含硫化合物中硫原子的电子云密度和空间位阻有关。考察了Ti-MWW/叔丁基过氧化氢催化氧化体系对成品柴油的催化氧化脱硫,结果表明,成品柴油中的含硫化合物可被有效地氧化脱除,在优化的反应条件下,经过两次氧化、萃取后,成品柴油中的总硫含量从1015μg/mL降低至11μg/mL,总脱硫率达到99%。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。