熔融制样X射线荧光光谱法测定陶瓷、色料和釉等物料中主量及次量元素

采用熔融片制样用X射线荧光光谱法对陶瓷、色料和釉物料中Na、Mg、Al、Si、P、S、K、Ca、Ti、Mn、Fe、Ba、Zr、Zn、Hf等15种元素进行了测定,用理论α系数校正基体效应。方法简便、快速、分析结果的准确度完全能满足上述物料分析的要求。本法还用纯化学试剂和标准样品按一定比例混合制备标准样品,弥补了色料和釉缺少标准或没有标样的困难。又对Zr和Hf元素分析线进行了选择,用ZrLα和HfLB1 作为分析线,而不采用ZrKα,不仅使制备的熔片达到ZrLα线的饱和厚度,使分析结果的准确度和重现性好,而且还消除了ZrKα的谱线对HfL B1分析线的干扰。     

X射线荧光光谱法测定陶瓷、色料和釉等物料中主量及次量元素

采用熔融片制样用X射线荧光光谱法对陶瓷、色料和釉物料中Na,Mg,Al,Si,P,S,K,Ca,Ti,Mn,Fe,Ba,Zr,Zn,Hf 15种元素进行了测定,用理论α系数校正基体效应。方法简便、快速、分析结果的准确度完全能满足上述物料分析的要求。还用纯化学试剂和标准样品按一定比例混合制备标准样品,弥补了色料和釉缺少标准或没有标样的困难。又对Zr和Hf元素分析线进行了选择,用ZrLα和HfLβ1作为分析线,而不采用ZrKα,不仅使制备的熔片达到ZrLα线的饱和厚度,使分析结果的准确度和重现性好,而且还消除了ZrKα的谱线对HfLβ1分析线的干扰。     

熔片X射线荧光光谱法测定锡矿石中八种重金属元素

建立了X射线荧光光谱法测定锡矿石中8种重金属元素Fe,Cu,Zn,As,Sn,Sb,Pb,Bi的分析方法。通过固体纯物质机械混合研磨配制了校准曲线所用的标准样品。采用混合熔剂(Li2B4O7:Li BO2:Li F=10:2.5:1,质量比)加氧化剂Li NO3熔融制备了X射线荧光法所用玻璃片样品(混合熔剂:Li NO3:试样=20:3:1质量比)。在高温熔融过程中,易挥发元素As,Pb一直存在于熔体中,未随熔融时间的增加而出现挥发损失。使用外加内标元素法(In和Co)对元素Sn,Sb,Fe的吸收增强效应进行校正,其它元素使用Compton散射线内标法进行校正。采用干扰曲线法校正Pb Lα对As Kα以及Sn Lβ1背景峰对Sb Lα的谱线重叠干扰。各元素检出限分别为Fe 0.0074%,Cu 0.0043%,Zn 0.0025%,As 0.0036%,Sn 0.019%,Sb 0.010%,Pb 0.0039%,Bi 0.0026%。对国家一级标准物质锡精矿GBW07232和锡矿石GBW07281分别进行10次制样测量,各元素精密度(RSD)在0.11%~18%之间。     

微波消解-ICP-AES法测定氧化铝中杂质元素

采用微波消解法，将样品用磷酸溶解，用ICP-AES测定氧化铝中Na、K、Ca、Si、Fe、Ti、Mn、Zn、Cu、V、Cr和B等12种杂质元素，采用测定标样、加标回收试验和精密度试验证明该方法简便快速，准确可靠。     

基于全反射X射线荧光光谱测定污水痕量重金属元素

以Ga为内标,探究全反射X射线荧光光谱（TXRF）快速测定多质量梯度浓度多元素重金属溶液Mn、Fe、Co、Ni、Cu、Zn、As、Cd、Sn、Sb和Pb的可行性,并以实际生活污水为研究对象,比较分析了离心、过滤和消解3种预处理方式对测定污水中重金属元素的影响。实验结果表明,Mn、Fe、Co、Ni、Cu、Zn、As和Pb,较适宜用TXRF直接进行定量分析;Pb的Lα与As的Kα谱线重叠,致使As的回收率略高于其它元素;Cd、Sn和Sb元素,仅可用于趋势分析。当质量浓度为40和4 mg/L时,Mn、Fe、Co、Ni、Cu、Zn和Pb元素呈现出较高的准确度和精密度,回收率在99%～117%之间,相对标准偏差（RSD）处于1%～14%。随着质量浓度的逐渐降低,各元素的准确度和精密度表现出不同程度的下降,当质量浓度处于本次试验的最低水平4μg/L时,大部分元素的回收率与RSD已超出定量分析的要求。通过对生活污水的3种预处理方式进行比较,发现污水悬浮颗粒同样携带部分金属元素,经消解后,Mn、Fe、Co、Ni、Cu和Zn这6种元素的准确度和精密度最好,质量浓度范围在36～152μg/L之间,回收率均...     

电感耦合等离子体原子发射光谱(ICP-AES)法测定高纯铝中Fe、Cu、Mg、Zn、Ti

建立了用电感耦合等离子体原子发射光谱(ICP-AES)法测定高纯铝中Fe、Cu、Mg、Zn、Ti的方法。详细讨论了基体元素和共存元素对分析元素的光谱干扰,以及盐酸用量的影响;选择了合适的分析谱线,同时得出了各元素的检出限。证明用基体匹配的方法在Fe 259.940nm、Cu 327.396nm、Mg279.079nm、Zn 213.856nm、Ti 334.941nm处可准确、可靠地测定高纯铝中含量范围在0.001%~0.01%的Fe、Cu、Mg、Zn、Ti元素。     

X射线荧光光谱法测定垃圾焚烧炉渣中主要成分

使用X射线荧光光谱仪,采用粉末直接压片制样,以研磨的方式克服粉末样品的粒度效应,理论α系数法校正基体效应,建立了垃圾焚烧炉渣样品中SiO2、Fe2O3、MgO、Al2O3、CaO、K2O、TiO2、P2O5八组分的分析方法.用标准化法进行强度漂移校正,用内控标样制做校准曲线,测定结果的精密度和准确度可以满足日常分析要求.     

大洋底多金属结核样品中主、次、微量元素的X射线荧光光谱测定

制定了一个用X射线荧光光谱法测定大洋底多金属结核样品中主、次、微量元素的分析方法。样品用石墨坩埚、混合熔剂低倍稀释熔融,用人工标样作为校准标准。计算了COLA方程的理论α系数,用于校正28个分析元素的吸收-增强效应。本法测定结果与化学法结果相吻合。     

电感耦合等离子体发射光谱同时测定生物环境和地质样品中的常量微量和痕量元素

研究了用ICP-AES同时测定大气漂尘中常量、微量和痕量元素,探讨了样品的前处理方法,盐酸、硝酸和硝酸-高氯酸对谱线强度的影响,研究了谱线之间的相互干扰情况和干扰校正,对其中大多数元素做了回收率试验。在折衷条件下应用本方法测定了美国NBS SRM1648城市颗粒物标准样品中的Ba、Ca、Cd、Co、Cu、K、Mg、Mn、Sr、Zn、Al、Fe、Li、Mo、Na、Ni、Sb、Ti、P、S、Sc和V,测定结果与标准值一致。     

熔融制样–X射线荧光光谱法同时测定铀钼矿中主次成分

采用混合熔剂熔融制样,建立了同时测定铀钼矿中U,Mo,SiO_2,Fe_2O_3,Al_2O_3等的X射线荧光光谱法。以Li_2B_4O_7–LiBO_2作为熔融试剂,NH_4NO_3作为样品的氧化剂,样品与熔剂的质量比为1∶10。除使用铀矿石国家标准物质外,主要选取人工混合校准样品及历年实验室比对的铀钼矿校准样品绘制成工作曲线。采用理论系数法校正样品的基体效应,用Br Kα,Zr Kα,U Lα,Ba Lα,Zn Kα谱线扣除相应元素的谱线重叠干扰。该方法各组分测定结果的相对标准偏差均小于2.0%(n=10);用标准物质验证方法的准确度,测定值相对误差在0.00~8.00%之间,与标准值基本吻合。该法应用于生产实验中,可以满足对铀钼矿准确、快速的测量要求。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.