顶空气相色谱法测定大蒜主要含硫化合物在烹饪后油脂中的含量

采用顶空毛细管气相色谱法/氢火焰离子化检测器,分析了大蒜中主要含硫化合物(如:二烯丙基硫醚、二烯丙基二硫醚、二烯丙基三硫醚)在烹饪后油脂中的含量变化。优化的色谱条件为以DM2WAX石英弹性毛细管色谱柱进行分离,平衡温度为403 K,搅拌速度为500 r/min,平衡时间为20 min。在所考察的浓度范围内,该方法呈现出良好的线性关系,相关系数大于0.999,检出限为0.001~0.025 mg/L,3种含硫化合物的平均回收率为97.1%~103.0%。     

冷柱头程序升温进样-气相色谱/质谱法研究新鲜大蒜中的有机硫化合物

采用冷溶剂提取新鲜大蒜中的有机硫化合物,结合冷柱头程序升温进样,对大蒜原始组分进行了气相色谱/质谱分析 。该法实现了从提取到色谱分离的“冷过程”,因而可以准确地鉴定大蒜提取液在热分解前的原始组分。分析结果表明, 在大蒜提取液中含有3-乙烯基-1,2-二硫杂-5-环己烯及其异构体2-乙烯基-1,3-二硫杂-4-环己烯两种主要组分以及少量 的S-甲基甲烷硫代亚磺酸酯、二烯丙基二硫醚、二烯丙基三硫醚。对大蒜的冷溶剂提取液和水蒸气蒸馏提取的大蒜油中 的有机硫化合物进行了比较,对一些主要有机硫化合物的形成进行了初步探讨。     

选择离子流动管质谱法测定大蒜酶解液顶空中17种有机硫化合物

采用选择离子流动管质谱(SIFT-MS)法,顶空取样后,以H3O+,NO+或O2+为初始离子,定量分析了17种大蒜酶解液挥发性有机硫化合物。结果表明:有机硫化合物主要为二烯丙基硫醚、甲基烯丙基硫醚、硫代亚磺酸酯和硫醇,其中二烯丙基二硫醚浓度为137 g/m3,二烯丙基三硫醚浓度为13.4 g/m3,甲基烯丙基二硫醚浓度为8.98 g/m3,它们分别占17种有机硫化合物总含量的77.3%,7.58%和5.08%(相对含量);本研究采用顶空取样方法测出大蒜素的浓度为5.63 g/m3,相对含量为3.20%。     

蒜油中几种有机多硫化合物质谱的研究

本文给出了大蒜挥发油中五种有机硫化合物的质谱图,通过质谱图解析,确定它们分别是1,2,3,4-四硫代环庚烷,1,2,3,4,5-五硫代环辛烷,二烯丙基四硫醚,二丙烯基四硫醚,5-烯丙基-1,2,3,4-四硫代环庚烷。     

HPLC-DAD法分析硝基化合物的影响因素EI北大核心CSCD

利用液相色谱对邻硝基甲苯、间硝基甲苯、对硝基甲苯、硝基苯、1,3,5-三硝基苯、2,4-二硝基甲苯、2,6-二硝基甲苯、环三亚甲基三硝胺、环四次甲基四硝胺、2,4,6-三硝基甲苯10种硝基化合物进行了分离,研究了色谱柱温度、流动相成分和流速对分离效果的影响。升高色谱柱温度或加快流动相流速都会使化合物的分离度变差。流动相成分的变化对各化合物分析的影响较大,不仅会改变化合物的分离度,还会使吸收波长发生移动。色谱柱为Zorbax Eclipse XDB-C_(18)(4.6×250 mm,5μm),色谱柱温度≤30℃、流动相为甲醇:水=55:45(V/V)、流速在0.6~1.2 m L/min时10种硝基化合物可以达到较好的分离。     

HPLC-DAD法分析硝基化合物的影响因素

利用液相色谱对邻硝基甲苯、间硝基甲苯、对硝基甲苯、硝基苯、1,3,5-三硝基苯、2,4-二硝基甲苯、2,6-二硝基甲苯、环三亚甲基三硝胺、环四次甲基四硝胺、2,4,6-三硝基甲苯10种硝基化合物进行了分离,研究了色谱柱温度、流动相成分和流速对分离效果的影响。升高色谱柱温度或加快流动相流速都会使化合物的分离度变差。流动相成分的变化对各化合物分析的影响较大,不仅会改变化合物的分离度,还会使吸收波长发生移动。色谱柱为Zorbax Eclipse XDB-C_(18)(4.6×250 mm,5μm),色谱柱温度≤30℃、流动相为甲醇:水=55:45(V/V)、流速在0.6~1.2 m L/min时10种硝基化合物可以达到较好的分离。     

二维液相色谱法在线检测哈茨木霉发酵液中2460A含量

建立了在线检测哈茨木霉发酵液中微量2460A的二维液相色谱方法。利用Ultimate 3000双三元液相色谱仪,采用阀切换二维色谱技术,组合3根色谱柱实现2460A的在线净化、富集和含量检测。净化柱采用资生堂MF C8柱(10 mm×4.6 mm,5.0μm),富集柱采用资生堂MGC18柱(20 mm×4.6 mm,5.0μm),以水-甲醇为流动相,梯度洗脱,流速2.0 m L/min;二维分析柱采用Thermo Hypersil GOLD C18柱(250 mm×4.6 mm,5.0μm),以水-甲醇为流动相,梯度洗脱,流速1.0 m L/min;进样量1.0 m L;柱温40℃;检测波长424 nm。方法验证结果显示,2460A的线性范围为0.0025~10.0 mg/L(r=0.9981,n=8),检出限为1.2μg/L;定量限为2.5μg/L;方法回收率为88.0%~104.4%。     

固相萃取-超高效液相色谱-串联质谱法同时测定大气降水中9种全氟化合物前体物质

采用固相萃取-超高效液相色谱-电喷雾串联三重四极杆质谱联用技术,建立了大气降水中9种全氟化合物前体物质的高通量检测方法。使用HLB固相萃取柱富集和净化降水样品中的目标化合物,以HSS T_3色谱柱(100mm×2.1 mm,1.7μm)为分析柱,甲醇和水作为流动相进行梯度洗脱。质谱以电喷雾负离子电离,采用多反应监测模式检测。9种目标化合物在0.05~5.00μg/L、0.5~50.0μg/L或5.00~500μg/L浓度范围内线性良好,相关系数为0.992 1~0.999 5,方法的检出限为0.05~7.9 ng/L;高、中、低3个添加水平的回收率为76.0%~106%,相对标准偏差为0.72%~13.7%。实验结果表明,该方法灵敏、准确,且具有检测范围广、分析速度快等特点,是一种适用于大气降水样品中全氟化合物前体物质检测分析的方法。     

全二维气相色谱分析直馏柴油中含硫化合物

采用全二维气相色谱-硫化学发光检测器,以直馏柴油为研究对象,考察了一维色谱柱初始温度、升温速率及两维柱温温差等条件对含硫化合物分离的影响,建立了直馏柴油中含硫化合物的分析方法。本方法对基质复杂的直馏柴油中含硫化合物的分离,并定性分析或归类了直馏柴油中的主要含硫化合物。以苯并噻吩为测试样,以峰面积对浓度作图,硫的浓度在1～100mg/kg范围内,峰面积与硫的浓度呈线性关系,相关系数大于0.999。与传统一维气相色谱相比,全二维气相色谱技术除可检测到苯并噻吩类、二苯并噻吩类等含硫化合物外,还可检测到直馏柴油中的硫醚类化合物;苯并噻吩类和二苯并噻吩类化合物也可得到较好分离。     

液相色谱-质谱法测定墨水中蓖麻油硫酸钠

建立了用液相色谱串联质谱对蓖麻油硫酸钠进行定性定量的分析方法.采用 SR-CN型色谱柱(100 mm×4.6 mm,3.5μm),以甲醇-水(1 1)为流动相,流速500 βL·min-1.质谱测定中采用电喷雾电离源,负离子采集模式,定量离子对m/z 377/297.该方法检出限为0.1 mg·L-1,线性范围0.4～400 mg·L-1.方法用于墨水中蓖麻油硫酸钠的定性定量分析.     

Thermodynamics of ionization of water over wide ranges of temperature and pressure

We have summarized results of many experimental investigations of the thermodynamics of ionization of H₂O(liq.) from 0–300°C and from 1.0 atm to nearly 8000 atm. Results of these investigations (equilibrium constants, enthalpies of ionization, heat capacities, partial molal volumes, and compressibilities) have been used for a number of thermodynamic calculations. It is particularly noteworthy that it is possible to use thermal data from 0–145°C with an equilibrium constant for 25°C in calculating reasonably accurate equilibrium constants for temperatures as high as 300°C. Similarly, it is possible to use volumetric data that refer to 1.0 atm in calculating useful equilibrium constants that apply for pressures as high as 2000 atm.Much of the work reported here was done while the author was on leave at the University of Lethbridge.     

Ambient ionization mass spectrometry: a tutorial

Ambient ionization is a set of mass spectrometric ionization techniques performed under ambient conditions that allows the direct analysis of sample surfaces with little or no sample pretreatment. Using combinations of different types of sample introduction systems and ionization methods, several novel techniques have been developed over the last few years with many applications (e.g., food safety screening; detection of pharmaceuticals and drug abuse; monitoring of environmental pollutants; detection of explosives for antiterrorism and forensics; characterization of biological compounds for proteomics and metabolomics; molecular imaging analysis; and monitoring chemical and biochemical reactions). Electrospray ionization and atmospheric pressure chemical ionization are the two main ionization principles most commonly used in ambient ionization mass spectrometry. This tutorial paper provides a review of the publications related to ambient ionization techniques. We describe and compare the underlying principles of operation, ionization processes, detecting mass ranges, sensitivity, and representative applications of these techniques.     

电喷雾离子源原理与研究进展

电喷雾离子源(ESI)是蛋白质组学研究采用的LC-MS/MS中最常用的接口之一,其作为一种软电离技术,具有可直接测定热不稳定化合物、形成多电荷离子等特征,在蛋白质组学研究中具有独特优势.本文介绍了电喷雾离子源(ESI)的工作原理与研究进展,并对各种新型离子化方法与应用进行了系统评述.     

Influence of the amino acid composition on the ionization efficiencies of small peptides

Electrospray ionization is widely used to generate gas phase ions from a variety of molecules ranging from small ions to large proteins, while the ionization mechanism is claimed to depend on the size of the molecule. For small molecules, the ionization efficiency, the amount of gas phase ions produced in the electrospray process, depends on the properties of the compound. Here, we show that the amino acid composition also influences the ionization efficiency of the oligopeptide. Additionally, we show that the ionization efficiencies of oligopeptides consisting of more than five amino acid residues are very similar to one another, and assuming equal ionization efficiencies is feasible. Therefore, accurate ionization efficiency predictions are needed mainly for small oligopeptides. For these oligopeptides, the amino acid composition can be used to estimate the ionization efficiency in an easy to use manner.     

New uses of thermionic ionization detectors in gas chromatography

Summary A newly designed thermionic detector was operated in two modes of thermionic ionization detection (TID), and a third mode of catalytic flame ionization detection (CFID). Operating modes were varied by changing the composition of the electrically-heated thermionic/catalytic source, and the composition of gases supplied to the detector. A TID-2 source activated by a low concentration of Cs/ceramic was operated in a dilute H₂/air environment and provided specific responses to nitrogen and phosphorus compounds. A TID-1 source activated by a high concentration of Cs/ceramic was operated in a N₂ environment and provided very high specificities and picogram detectivities to compounds containing electronegative functional groups such as the NO₂ group. A CFID source formed from Ni/ceramic was operated in a H₂/air flame environment and provided universal responses to all organics with enhanced responses to some heteroatom compounds.Presented at the 14th International Symposium on Chromatography London, September, 1982     

常压电喷雾离子化的机理及应用

作为最有前景的分析仪器之一,质谱技术已在药物、食品、环境、人类健康、国家安全及相关领域展现出广阔的应用前景。不同种类的分析物具有多种特征,这为直接离子化及质谱分析增加了难度。常压敞开式离子源是近年来新兴的一种离子源,这类离子源具有无需复杂的样品前处理、操作方便、快速、非破坏性、灵敏度及特异性好、能实现实时原位、高通量分析等特点。本文综述了基于电喷雾离子化(ESI)原理的各种离子源的电离机理、特征及应用,展望了常压敞开式离子源的发展趋势。     

快速蒸发电离质谱技术及其应用研究进展

近年来,原位电离质谱技术成为质谱分析领域的研究前沿和热点。快速蒸发电离质谱技术源于外科手术中的手术烟雾现象,自2009年报道以来,作为一种新型原位电离质谱技术已被广泛应用于医学、微生物鉴定、食品真伪鉴别、代谢物研究、药用植物成分鉴定等领域。该技术通过电离切割组织或其他生物样品产生的含丰富特定区域生物特征的气溶胶,对其进行原位、在线、实时、快速质谱分析。该文阐述了快速蒸发电离质谱技术的发展历程、电离机制及工作原理,并对其在不同领域的应用研究进展进行了综述,可为相关领域研究人员提供科研思路和技术参考。     

多溴联苯醚代谢物的色谱保留和质谱特征

研究了多溴联苯醚(PBDEs)代谢物中常见的18种羟基PBDEs(HO-BDEs)、15种甲氧基PBDEs(MeO-BDEs)的气相色谱、反相液相色谱分离和质谱碎片特征。MeO-BDEs在反相液相色谱(RPLC)的保留行为受疏水作用支配,而HO-BDEs则还受到除疏水作用以外的特殊作用影响。LC/MS中大气压化学电离(APCI)源适用于HO-BDEs检测,而APCI源以及电喷雾离子源(ESI)对MeO-BDEs都没有响应。质谱碎片具有显著取代位效应:在LC/APCI-MS中,邻位取代HO-BDEs的碎片离子基峰均为脱一个溴的结构[M-H]--HBr,而对位取代的基峰则为准分子离子[M-H]-;在电子电离(EI)源质谱仪下,邻位取代MeO-BDEs有脱溴甲烷碎片离子(M. -BrCH3),对位取代有特征的脱甲基自由基结构(M. -.CH3),间位取代则无上述两种碎片离子。     

The role of different phenomena in surface-activated chemical ionization (SACI) performance

In previous studies, the production of ions in an APCI source without any corona discharge was observed, and the intensity of the ion signals showed significant increases on placing a metallic surface at 45 degrees inside an orthogonal ion source. This method was named surface-activated chemical ionization (SACI). The present study was performed to investigate the mechanisms of ion production with or without the presence of the metallic surface, by varying instrumental parameters and the geometrical configuration. Approximate calculations show that, in the absence of corona discharge and of any additional surfaces, ions cannot be produced by collisional phenomena, because of their low kinetic energy, in the 10(-2) to 10(-3) eV range. Two alternative possibilities have been considered: the first takes into account that ions may originate by collision of neutral clusters of polar solvent molecules with the APCI source surfaces through clusterelectric effect. The second takes into account that the water dissociation constant k(w) is temperature dependent, passing from 10(-14.1669) at 20 degrees C to 10(-12.4318) at 90 degrees C. It means that the [H(+)] varies from 8.3 x 10(-8) to 6.1 x 10(-7) M going from 20 to 90 degrees C. Hence, at the high temperatures experimented in the APCI vaporizer, H(+) becomes available in solution in molar quantities analogous to those of analyte, and the protonation of the analyte itself can consequently occur. The activation of further ionization processes in the presence of the metallic surface can be reasonably attributed to interactions between gas-phase analyte molecules and solvent molecules adsorbed on the surface. Experiments performed with a thin layer of deuterated glycerol on the surface led to unequivocal results, i.e. the production of [M + D](+) ions of the analyte.     

Thermal and Potentiometric Titrations of Phytic Acid

Abstract

Values for the ionization constants and the heats of ionization of phytic acid (inositol hexaphosphate) have been determined by simultaneous potentiometric and thermal titration in a titration microcalorimeter. The potentiometric results are in substantial agreement with those found by discontinuous titration; the heat liberated from pH 10.4 to 6.8 is essentially that found using a batch microcalorimeter. Ionization of phytic acid may be generally characterized as having five groups similar to pK of phosphoric acid, two groups similar to pK2 of phosphoric acid and 4 groups similar to pK4 of pyrophosphoric acid. A single group has pK ～ 5 with ΔH_i ～ -1.1 kcal/mol.