毛细管电泳-场强放大堆积技术对制剂中磺胺嘧啶和磺胺甲噁唑的测定研究

利用高效毛细管电泳-场强放大柱内堆积技术分离测定磺胺嘧啶(SD)和磺胺甲噁唑(SMZ)。采用未涂层熔融石英毛细管柱(60.2 cm×75μm,有效长度50 cm),以50 mmol/L NaH2PO4(pH6.0)为运行缓冲液,分离电压27.5 kV,柱温25℃,检测波长214 nm进行测定。进样前压力进水3.42 kPa×12 s;电动进样-10kV×9 s。SD和SMZ的线性范围分别是0.05~10.00 mg/L(r=0.999 9),0.025~5.00 mg/L(r=0.999 4),检出限分别为1.74、1.39μg/L;将此方法应用于实际样品测定,SD回收率为98%~103%,SMZ回收率为97%~103%。     

磺胺甲噁唑的二阶导数差示脉冲极谱法测定

建立了磺胺甲噁唑的二阶导数差示脉冲极谱定量分析方法,磺胺甲噁唑在10% HCl-(硼酸-氯化钾缓冲溶液)-水(5:5:90)的底液中,于-1.45 V(vs.Ag/AgCl)处出现一良好的二阶导数差示脉冲极谱峰,磺胺甲噁唑浓度与其峰高在0.08～0.80 mmol/L范围内呈线性关系(p＜0.01),检测限为8.6 nmol/L.本法简便、快速、灵敏,结果准确.     

1,2-萘醌-4-磺酸钠体系分光光度法测定磺胺甲噁唑

采用1,2-萘醌-4-磺酸钠体系分光光度法测定磺胺甲噁唑(SMZ)。磺胺甲噁唑与1,2-萘醌-4-磺酸钠在pH=10.0的缓冲溶液中发生亲核取代反应生成橙红色的产物,组成比为1:1,最大吸收波长λ=476 nm;表观摩尔吸光系数ε=6.44×103L/(mol.cm);SMZ浓度在0.2~60 mg/L范围内呈良好的线性关系;线性回归方程为A=0.02452 0.02301C(mg/L),线性相关系数r=0.9991;检出限为0.08 mg/L;RSD为0.25%(20 mg/L,n=11);平均回收率为98.7%以上。优化了对磺胺甲噁唑的测定条件。初步探讨了反应机理,应用拟定的方法测定磺胺甲噁唑的含量,与药典法相比,结果满意。     

基于自组装与电聚合联用制备磺胺甲噁唑分子印迹传感器及特性研究

以磺胺甲噁唑为模板分子,甲基丙烯酸为功能单体,马来松香丙烯酸乙二醇脂为交联剂,采用自组装与电聚合相结合方法,制备了一种对磺胺甲噁唑具有特异性识别位点的分子印迹电化学传感器。通过循环伏安法(CV)、示差脉冲伏安法(DPV)和安培计时法(I-t)表征了该印迹传感膜的电化学性能。结果表明,该传感器具有良好的选择性和灵敏度。在5.0×10-6~2.4×10-3mol·L-1浓度范围内峰电流与浓度呈良好线性关系(R=0.9943);检测限1.67×10-7mol·L-1(S/N=3);达到稳定电流所用时间小于2s。利用此方法成功测定了药物中磺胺甲噁唑的含量。     

紫外光谱净信号法测定酸性环境下复方磺胺甲噁唑片两个有效组分

被分析组分的光谱净信号将正交于其它药物组分和辅料光谱所张成的光谱子空间,从而消除其它组分对被分析组分的光谱干扰,此净信号将与被分析组分的浓度成正比,据此建立了药物制剂分析的净信号方法。本文利用该方法研究了在酸性条件下紫外光谱测定复方磺胺甲噁唑片的两种有效成分磺胺甲噁唑(SMZ)和甲氧苄啶(TMP)。SMZ和TMP的线性范围分别为0.48~7.84μg/mL(r=0.9981)和0.12~1.5μg/mL(r=0.9986),平均回收率分别为99.5%和101.0%,RSD分别为1.87%和3.60%。本法简便、快速和准确,可用于酸性条件下复方磺胺甲噁唑片中SMZ和TMP含量的快速、同时准确测定。     

胶体金免疫层析法对组织样品中磺胺甲噁唑残留的快速检测

研究了用于快速检测组织样品中磺胺甲噁唑残留的胶体金免疫层析检测试剂.采用免疫竞争法,将抗磺胺甲噁唑多克隆抗体-胶体金复合物包被在胶体金结合垫上,同时将人工合成的磺胺甲噁唑抗原包被在硝酸纤维素薄膜表面作为检测线(T线),将抗磺胺甲噁唑多克隆抗体的羊抗兔二抗包被在硝酸纤维素薄膜表面作为质控线(C线).T线的人工抗原与待测样品中的磺胺甲噁唑竞争结合胶体金标记的磺胺甲噁唑多克隆抗体,通过T线与C线的显色对比读出结果.采用该检测试剂检测组织试样时,定量下限可达20 μg/L,整个检测过程只需3 ～5 min,且与磺胺嘧啶、磺胺二甲基嘧啶、盐酸克伦特罗、四环素、青霉素、链霉素无交叉反应.检测试剂具有较高的灵敏度及特异性,操作便捷,稳定可靠,可作为组织中磺胺甲噁唑残留现场监控的有效筛检手段.     

同步荧光法测定复方新诺明中磺胺甲基异噁唑和甲氧苄氨嘧啶的含量研究

本文采用同步荧光技术对复方新诺明中有效成份磺胺甲基异噁唑和甲氧苄氨嘧啶进行测定,在△λ分别为72nm和94nm的条件下,测定样品中所含有效成份相当于标示量的95.12％～105.68％;回收率为95.5％～98.1％;线性范围磺胺甲基异噁唑为0.125～4.00μg/ml。甲氧苄氨嘧啶为0.125～3.00μg/ml;相关系数分别为0.9976和0.9978.不经分离和掩蔽直接连续测定,效果良好。     

磺胺甲噁唑的示波极谱测定及其电化学行为

拟定了测定磺胺甲唑的单扫描导数示波极谱法。在0.18mol/LHAc NaAc(pH4.4)缓冲溶液中,磺胺甲唑于-1.36V(vs.SCE)处产生一极谱还原波,其二阶导数峰电流i″p与磺胺甲唑浓度在3.7×10-7～4.5×10-4mol/L范围内呈良好线性关系(r=0.9993,n=9).检出限为8.0×10-8mol/L。该法灵敏、简便、快速,用于片剂中磺胺甲唑含量的测定,结果满意。     

在1,4-二氧六环介质中用导数三波长光度法同时测定抗菌优中各组分含量

本文提出了抗菌优(复方磺胺甲(口恶)唑)中磺胺甲基异(口恶)唑(SMZ)和甲氧苄胺嘧啶(TMP)两组分导数三波长同时测定的新方法。该法利用TMP在二氧六环中E_2带的增色效应和紫移作用以及UV-265光度计的指令链功能,达到了灵敏,准确、快速的目的。     

近红外光谱快速测定复方磺胺甲噁唑药效成分

基于近红外漫反射光谱技术,利用偏最小二乘多元校正方法建立了复方磺胺甲噁唑片中的两个有效成分磺胺甲噁唑(SMZ)和甲氧苄啶(TMP)含量的快速同时测定方法。对于SMZ和TMP定量分析模型,相关系数分别为99.969%与99.938%,校正集残差分别为0.217与0.159,而预测根均方差分别为0.310和0.418。该方法具有简单、快捷、两组分同时准确测定以及样品不经任何预处理等特点。     

Electroanalytical and chromatographic determination of pentachlorophenol and related molecules in a contaminated soil: a real case example

Electroanalytical and chromatographic methodologies have been applied for the determination of pentachlorophenol (PCP) and some of its derivatives in real soil samples contaminated by industrial discharge. The analytes were extracted with hexane from soil samples collected at different points of the site and mixed to produce a representative sample. Square wave voltammetry (SWV) experiments were carried out on either a boron-doped diamond (BDD) electrode or a gold ultramicroelectrode (Au-UME) in an analyte composed by the Britton-Robinson (B-R) buffer at pH 5.5 with the direct addition of proper amounts of the extract. The voltammetric responses revealed an irreversible anodic peak at approximately 0.80 V vs. Ag/AgCl with a peak current showing a linear dependence on PCP concentration. This linear relationship yielded a detection limit (DL) of 2×10⁻⁸ mol l⁻¹ (or 5.5 μg l⁻¹) for the BDD electrode and 6.9×10⁻⁸ mol l⁻¹ (18.4 μg l⁻¹) for the Au-UME, while the independently measured HPLC detection limit was 1.1×10⁻⁸ mol l⁻¹ (3.0 μg l⁻¹). The application of electroanalytical and chromatographic methodologies in the analysis of soil extracts revealed, besides the PCP responses, signals for some related molecules such as o-tetrachlorobenzoquinone (o-chloranil), hexachlorobenzene and tetrachlorophenol. Recovering experiments for PCP showed a concentration of 27.5 mg kg⁻¹ for the electroanalytical determinations and 26.8 mg kg⁻¹ for the HPLC analysis, values exceedingly high if considering that the maximum residue limit established for natural waters by the Brazilian Environmental Agency is 10 μg l⁻¹.     

Individual and simultaneous fluorimetric determination of glycine and cysteine by flow injection analysis

A dual-channel flow injection configuration is proposed for individual and simultaneous determinations of glycine and cysteine (based on their reaction with phthaldialdehyde) in the range 1 × 10⁻⁷ – 1.5 × 10⁻⁵ M, with relative standard deviations of ± 1.7 and ± 1.3%, respectively, and a sampling frequency of 75–80 hr⁻¹ for both analytes. The inclusion of a selecting valve in the configuration allows the simultaneous determination of these analytes in the concentration range achieved in their individual determinations. The resolution of mixtures is feasible with average errors of ± 2.2%.     

Evaluation of a chloramine-T-selective electrode for catalytic titration of silver and mercury(II) based on iodide-catalyzed chloramine-T reactions

Semiautomatic methods are described for the catalytic titrimetric determination of microamounts of silver and mercury(II) using a chloramine-T-selective electrode as monitor. The methods are based on the inhibitory effect of Ag(I) and Hg(II) on the iodide-catalyzed chloramine-T-arsenite and chloramine-T-H₂O₂ reactions. Microamounts of silver in the range 0.2–200 μg (1 × 10⁻⁷−1 × 10⁻⁴ M) and of mercury(II) in the range 0.1–200 μg (2.5 × 10⁻⁸−5 × 10⁻⁵ M) were determined using the chloramine-T-As(III) indicator reaction. Mercury(II) in the range 4–2000 μg (1 × 10⁻⁶−5 × 10⁻⁴ M) was also determined using the chloramine-T-H₂O₂ indicator reaction. The accuracy and precision were in the range 0.1–1%.     

白藜芦醇作辣根过氧化物酶底物的布氏杆菌抗体酶联免疫传感器研究

一种纯天然产物白藜芦醇用作辣根过氧化物酶(HRP)底物。对其化学性质的研究证实,白藜芦醇在空气中较稳定,对HRP、H2O2的电化学响应性能优于传统HRP底物,对人体无毒害。白藜芦醇在HRP催化下可被H2O2氧化成醌,产物醌在电极上于-376 mV处可被还原,其电流的大小与HRP的浓试在一定浓度范围内呈线性相关。将兔布氏杆菌抗原包埋在石墨-石蜡基质中制备了测定兔布氏杆菌抗体的电化学酶联免疫传感器,该传感器测定兔布氏杆菌抗体的线性范围为3×10-4~1.65×10-2g/L;检出限为1×10-4g/L;RSD为4.6%。本方法制备免疫传感器的电化学性能稳定,抗原活性保持良好。     

Design of fluorescent self-assembled multilayers and interfacial sensing for organophosphorus pesticides

This paper details the fabrication of indole (ID) self-assembled multilayers (SAMs) and fluorescence interfacial sensing for organophosphorus (OP) pesticides. Quartz/APES/AuNP/l-Cys/ID film was constructed on l-cysteine modified Quartz/APES/AuNP surface via electrostatic attraction between ID and l-cysteine. Cyclic voltammetry indicates that ID is immobilized successfully on the gold surface. Fluorescence of the Quartz/APES/AuNP/l-Cys/ID film shows sensitive response toward OPs. The fluorescent sensing conditions of the SAMs are optimized that allow linear fluorescence response for methylparathion and monocrotophos over 5.97 × 10⁻⁷ to 3.51 × 10⁻⁶ g L⁻¹ and 3.98 × 10⁻⁶ to 3.47 × 10⁻⁵ g L⁻¹, with detection limit of 6.1 × 10⁻⁸ gL⁻¹ and 3.28 × 10⁻⁶ gL⁻¹, respectively. Compared to bulk phase detection, interfacial fluorescence sensing based on the SAMs technology shows higher sensitivity by at least 2 order of magnitude.     

Application of the atomic Faraday eftect to the trace determination of elements (Cd, Ag and Cu)—effect of the hyperfine structure on the Zeeman splitting and line-crossing

Atomic Faraday spectroscopy or atomic magneto-optical rotation spectroscopy (AMORS) combined with the electrothermal atomization was applied to the trace determination of elements (Cd, Ag and Cu). A simple theoretical treatment was developed for the dependence of the radiation transmitted through the Faraday configuration on the magnetic field strength. The effect of the hyperfine structure on the Zeeman splitting was related to the line-crossing between the Zeeman components and the dependence of the transmitted intensity on the magnetic field strength. The calibration graphs demonstrated a square-law dependence. The spectroscopic signal increased non-rectilinearly as the source radiance increased. Detection limits of 5 × 10⁻¹³, 2 × 10⁻¹¹ and 3 × 10⁻¹¹ g were obtained for Cd, Ag and Cu, respectively.     

阳离子表面活性剂对电化学法测试牛奶中氯霉素残留量的影响

为探索用电化学方法检测生物样品中氯霉素残留的高灵敏度技术,本实验研究了阳离子表面活性剂十六烷基三甲基溴化铵(CTMAB)对氯霉素在玻碳电极上伏安行为的影响,实验结果表明,以0.02 mol/L高氯酸为支持电解质,在0.40~-0.60 V的范围内进行伏安扫描时,2×10-5mol/L CTMAB能显著提高氯霉素在-0.41 V处的还原峰电流。利用这种改进的电化学方法检测氯霉素的线性范围为0.0026~8 mg/L,检出限达到0.83μg/L。研究了缓冲液种类及其酸碱度及其它表面离子活性剂等对测试氯霉素的影响。     

Separation and determination of l-tyrosine and its metabolites by capillary zone electrophoresis with a wall-jet amperometric detection

A method of capillary electrophoresis with wall-jet amperometric detection (AD) has been developed for separation and determination of l-tyrosine (Tyr) and its metabolites, such as Tyramine (TA), p-hydroxyphenylpyruvic (pHPP), homogentisic acid (HGA) and some dipeptides containing Tyr, such as Tyr-Gly-Gly (YGG), Tyr-Arg (YR) and Tyr-d-Arg (Y-d-R). A carbon disk electrode was used as the working electrode and the optimal detection potential was 1.00 V (versus Ag/AgCl). At 18 kV of applied voltage, the seven compounds were completely separated within 20 min in 110 × 10⁻³ mol/L Na₂HPO₄–NaH₂PO₄ buffer (pH 7.10) containing 3 × 10⁻³ mol/L β-cyclodextrin (β-CD). Good linear relationship was obtained for all analytes and the detection limits of seven analytes were in the range of 0.95–4.25 ng/mL. The proposed method has been applied to examine the metabolic process of l-tyrosine in rabbit's urine.     

Voltammetric study of the interaction of lomefloxacin (LMF)–Mg(II) complex with DNA and its analytical application

The voltammetric behavior of the LMF-Mg(II) complex with DNA at a mercury electrode is reported for the first time. In NH₃–NH₄Cl buffer (pH=9.10), the adsorption phenomena of the LMF–Mg(II) complex were observed by linear sweep voltammetry. The mechanism of the electrode reaction was found to be a reduction of LMF in the complex, and the composition of the LMF–Mg(II) complex is 2:1. In the presence of calf thymus DNA (ctDNA), the peak current of LMF–Mg(II) complex decreased considerably, and a new well-defined adsorptive reduction peak appeared at −1.63 V (vs. SCE). The electrochemical kinetic parameters and the binding number of LMF–Mg(II) with ctDNA were also obtained. Moreover, the new peak currents of LMF–Mg(II)–DNA system increased linearly correlated to the concentration of DNA in the 4.00×10⁻⁷–2.60×10⁻⁶ g ml⁻¹ range when the concentrations of LMF–Mg(II) complex was fixed at 5.00×10⁻⁶ mol l⁻¹, with the detection limits of 2.33×10⁻⁷ g ml⁻¹. An electrostatic interaction was suggested by electrochemical method.     

Application of Voltammetric Method of Total Chromium Determination in the Presence of Cupferron for Selective Determination of Cr(VI) in Water Samples

A voltammetric method of Cr(VI) determination in a flow system based on the combination of selective accumulation of the product of Cr(VI) reduction on hanging mercury drop electrode and a very sensitive method of chromium determination in the presence of cupferron previously described is proposed. The calibration graphs were linear from 3 × 10⁻⁹ to 3 × 10⁻⁸ and from 5 × 10⁻¹⁰ to 5 × 10⁻⁹ mol L⁻¹ for accumulation times of 120 and 600 s, respectively. The detection limit for the accumulation time of 600 s was 9 × 10⁻¹¹ mol L⁻¹. The relative standard deviation was 5.1% (n = 5) for Cr(VI) concentration 1 × 10⁻⁸ mol L⁻¹ and the accumulation time of 120 s. The influence of foreign ions commonly present in water samples is presented. The validation of the method was made by studying the recovery of Cr(VI) from spiked natural water samples.