维生素E绿色还原法制备银纳米粒子的研究

采用一种绿色还原法制备银纳米粒子,以维生素E为还原剂,淀粉为稳定剂,在液相中还原硫酸银,通过改变溶液的pH值和反应时间,得到不同粒径的黄色银纳米粒子,并分别采用透射电镜、红外光谱、紫外-可见吸收光谱、扫描电镜和电化学方法对银纳米粒子进行表征。结果表明:维生素E在溶液中被氧化生成苯醌,反应得到的银纳米粒子为球形,粒径为8~25 nm;在较强碱性条件下,得到的银纳米粒子尺寸较小,分布较均匀,其平均粒径约为10 nm;不同条件下生成的银溶胶分别在417、411、409、408 nm处出现紫外吸收峰,这些吸收峰均为银纳米粒子的表面共振吸收;生成的银纳米粒子具有很好的电化学性质,并对L-半胱氨酸的电化学反应显示了良好的催化活性。     

TiO2纳米膜表面结构形态特征

采用反胶束法制备TiO2纳米溶胶,用浸渍提拉法在不同的条件下制备了三种TiO2多孔纳米薄膜,并利用AFM、SEM、XRD等方法对膜表面结构物理化学特性进行表征.结果表明三种膜基本上由粒径约为59 nm的纳米粒子以不同的方式堆积而成,溶胶刚生成时浸提一次,干燥、焙烧得到膜上纳米粒子分布均匀,所生成的二次粒子粒径最小,二次粒子形成的二次表面粗糙度最小,浸提10次得到膜上纳米粒子间存在较丰富缝隙结构,二次粒子粒径及其形成的表面粗糙度较大,而溶胶制备好陈化6 h后浸提得到的膜上二次粒子粒径最大,表面粗糙度最高.由分形理论估算得到三种膜的分形维数分别是2.22、2.20和2.27. XRD测试表明,膜上TiO2为锐钛矿晶相.这些结果表明,采用不同制备步骤得到的膜,其表面结构形态存在较大的差异.     

酸和碱催化制备二氧化硅溶胶及其稳定性

以正硅酸乙酯(TEOS)为原料,氨水和盐酸为催化剂,制备了SiO2溶胶;研究了pH值对溶胶的稳定性以及SiO2粒子生长方式的影响.结果表明,在酸性条件下,随着pH值的增加,凝胶时间呈现先变长后变短的趋势;而在碱性条件下,凝胶时间随pH的增大快速增加.透射电镜(TEM)和动态光散射(DLS)分析结果表明,溶胶中的SiO2粒子处于纳米量级,且两种催化条件下粒子的粒径分布存在明显差异.     

紫外光辐射对TiO2溶胶的影响研究

用紫外-可见吸收光谱、动态光散射与透射电镜研究紫外光辐射对T₂溶胶的影响,结果表明,光辐射使T₂溶胶在可见光区的吸收减少,紫外区吸收增加,吸收带隙增大.与非光辐射的T₂溶胶粒子相比,光辐射使T₂溶胶粒子分布均匀且平均粒径减小,提高了T₂纳米粒子在室温下的晶化程度.     

稀土镧对真空蒸发沉积银纳米粒子团聚的影响

用透射电镜（TEM）和扫描电镜（SEM）研究了稀土镧对真空蒸发沉积银纳米粒子的影响.结果表明,稀土镧对真空蒸发沉积银纳米粒子有明显的细化作用.稀土镧对银纳米粒子的细化作用,是由于稀土镧增强了基底对银原子的吸附能,使镧和银结合形成的复合小银粒子局限于固定位置,进而减少了相互团聚所致.     

不同形态银纳米粒子的非线性光学特性

通过光诱导生长制备了三角形和圆盘形银纳米粒子, 并采用飞秒Z-scan技术考察了这2种形貌的银纳米粒子在800 nm光波长下的非线性光学特性. 在基态等离子漂白和自由载流子吸收等效应的作用下, 粒径为75 nm的三角形银纳米粒子的非线性透过率随激发光强的增加而呈现由饱和向反饱和非线性吸收过渡的现象; 粒径为35 nm的圆盘形银纳米粒子仅表现出反饱和吸收现象. 实验结果表明, 银纳米粒子非线性吸收过程受粒子形态调控.     

金银合金纳米粒子表面处理及其表面增强拉曼光谱研究

采用水合肼还原的方法制备了金银比例为1∶1的金银合金纳米粒子, 紫外可见吸收光谱显示合成的溶胶只有一个介于金和银之间的吸收峰, 证明了合金结构的形成. 通过氨基耦联方法将合金纳米粒子组装到硅片表面, 利用氯金酸与合金中银的反应对基底上合金纳米粒子表面进行了改性处理. 以吡啶为探针分子, 研究了表面处理前后基底的SERS效应的差别, 结果表明随着浸泡时间延长, 信号强度先逐渐增强后降低至不变, 这与合金纳米粒子表面结构的变化有关, 氯金酸与表面银的反应经历了两个过程, 即粒子表面形成小的孔洞(去合金过程)和AgCl(s)在粒子表面的沉积, 前者有利于SERS效应的提高, 而后者导致SERS效应快速衰减.     

金核银壳纳米粒子薄膜的制备及SERS活性研究

采用柠檬酸化学还原法制备金溶胶, 通过自组装技术在石英片表面制备金纳米粒子薄膜, 在银增强剂混合溶液中反应获得金核银壳纳米粒子薄膜. 用紫外-可见吸收光谱仪和原子力显微镜(AFM)研究了不同条件下制备的金核银壳纳米粒子薄膜的光谱特性和表面形貌, 并以结晶紫为探针分子测量了金核银壳纳米粒子薄膜的表面增强拉曼光谱(SERS). 结果表明, 金纳米粒子薄膜的分布、银增强剂反应时间的长短对金核银壳纳米粒子薄膜的形成均有重要影响. 制备过程中, 可以通过控制反应条件获得一定粒径的、具有良好表面增强拉曼散射活性的金核银壳纳米粒子薄膜.     

Theoretical consideration on preparing silver particle films by adsorbing nanoparticles from bulk colloids to an air-water interface

In our previous paper, a method for preparing enormous surface-enhanced Raman scattering (SERS) active substrates through the aggregation of silver particles trapped at an air-water interface was reported. Here, further efforts were devoted to investigate the origin of assembling silver particle films by adsorbing nanoparticles from bulk colloids to the air-water interface. It was revealed that it is thermodynamically favorable for a colloidal particle in bulk colloids to adsorb to the air-water interface; however, a finite sorption barrier between it and the nearby particles usually restrains the adsorption process. When an electrolyte such as KCl, which is commonly used as an activating agent for additional SERS enhancement, was added into silver colloids, it largely reduced the sorption barrier. Thus, silver nanoparticles can break through the sorption barrier, pop up, and be trapped at the air-water interface. The trapped silver particles are more inclined to aggregate at the interface than those in bulk colloids due to the increase of van der Waals forces and the reduction of electrostatic forces. The morphology of the as-prepared silver particle films was characterized by scanning electron microscope, and their SERS activity was tested using NaSCN as a probe molecule. The surface enhancement of the silver particle films is about 1-2 orders of magnitude higher compared with that of silver colloids, because most of the silver particles in the films are in the aggregation form that provides enormous SERS enhancement. Furthermore, the stability of such type of films is much better that of colloid solutions.     

Photochemical synthesis and self-assembly of gold nanoparticles

Colloidal gold was prepared by UV light irradiation of the mixture of HAuCl₄ aqueous solution and poly(vinyl pyrrolidone) (PVP) ethanol solution in the presence of silver ions. The resulting sheet-like nanoparticles were found to self-assemble into nanoflowers by a centrifuging process. The results of control experiments reflected that only suitable size sheet-like nanoparticles could assemble into the flower-like structures. The presence of Ag ions and PVP are essential for the formation process of nanoflowers. They perform their function by serving as structure-directing agents to produce the sheet-like particles. The appearance of the flower-like assemblages is attributed to the combination of Van der Waals force and the anisotropic hydrophobic attraction between the nanoparticles. The flower-like assemblages films can be used as surface-enhanced Raman spectroscopy (SERS) substrates with 4-aminothiophenol (4-ATP) molecule as a test probe.     

Novel Bottom‐Up SERS Substrates for Quantitative and Parallelized Analytics

Surface‐enhanced Raman spectroscopy (SERS) is an emerging technology in the field of analytics. Due to the high sensitivity in connection with specific Raman molecular fingerprint information SERS can be used in a variety of analytical, bioanalytical, and biosensing applications. However, for the SERS effect substrates with metal nanostructures are needed. The broad application of this technology is greatly hampered by the lack of reliable and reproducible substrates. Usually the activity of a given substrate has to be determined by time‐consuming experiments such as calibration or ultramicroscopic studies. To use SERS as a standard analytical tool, cheap and reproducible substrates are required, preferably with a characterization technique that does not interfere with the subsequent measurements. Herein we introduce an innovative approach to produce low‐cost and large‐scale reproducible substrates for SERS applications, which allows easy and economical production of micropatterned SERS active surfaces on a large scale. This approach is based on an enzyme‐induced growth of silver nanostructures. The special structural feature of the enzymatically deposited silver nanoparticles prevents the breakdown of SERS activity even at high particle densities (particle density >60 %) that lead to a conductive layer. In contrast to other approaches, this substrate exhibits a relationship between electrical conductivity and the resulting SERS activity of a given spot. This enables the prediction of the SERS activity of the nanostructure ensemble and therewith the controllable and reproducible production of SERS substrates of enzymatic silver nanoparticles on a large scale, utilizing a simple measurement of the electrical conductivity. Furthermore, through a correlation between the conductivity and the SERS activity of the substrates it is possible to quantify SERS measurements with these substrates.     

Nanoparticle-mirror sandwich substrates for surface-enhanced Raman scattering

Sandwich surface-enhanced Raman scattering (SERS) substrates (3S) utilizing coupling between continuous metal films and plasmonic particles were fabricated using silver mirrors, electrochemically roughened films, and various sizes of silver nanoparticles. The effect of excitation wavelength and nanoparticle size on SERS spectra of poly(vinylpyridine), selected as a model compound, was studied to determine the optimum conditions for the strongest SERS signal. The Raman enhancement resulted from the plasmon coupling of silver nanoparticles to the underlying continuous film as well as the lateral plasmon coupling between the silver nanoparticles. The formation of the charge transfer complex was also observed. The 3S configuration was used to obtain SERS spectra of dipicolinic acid (DPA), a chemical signature for Bacillus anthracis.     

Laser photolysis of silver colloid prepared by citric acid reduction method

By irradiating a silver colloid, prepared via the citric reduction method, using the second harmonic of a Nd:YAG laser, lambda = 532 nm, with laser fluence more than about 0.2 J/cm(2), we prepared a colloid consisting of small spherical silver nanoparticles with d(p) = 8 nm. The process of particle formation can be divided into three steps. First, large particles that existed in the initial colloid evaporate fully, producing a large amount of silver atoms. Next, primary particles with d(p) = 2-4 nm are formed in mini plumes. Finally, these primary particles grow up to 8 nm, as silver atoms diffuse to them through water.     

Au/Ag核-壳结构纳米粒子的制备及其SERS效应

随着大量有关表面增强拉曼散射 (SERS)的实验和理论研究的开展 ,金属纳米粒子作为一类重要的 SERS增强介质 ,已引起了人们浓厚的研究兴趣 [1] .而 Au和 Ag作为最常用的活性基底物质 ,更是研究的热点 [2 ,3 ] .最近 ,美国印第安那大学的 Nie等 [4 ] 在单个银纳米粒子上 ,观察到高达 1 0 14 ～ 1 0 15的SERS因子 .同时 ,他们的另外一项工作表明银纳米粒子的形状和大小对 SERS活性有很大影响 [5] .但是 ,由于 Ag溶胶制备的重复性较差 ,且粒度分布不均匀 ,通过控制银颗粒大小而调控 SERS活性是相当困难的[6] .与 Ag相比 ,Au在可见光…     

Self-assembled metal colloid films: two approaches for preparing new SERS active substrates

In this paper, we propose two new approaches for preparing active substrates for surface-enhanced Raman scattering (SERS). In the first approach (method 1), one transfers AgI nanoparticles capped by negatively charged mercaptoacetic acid from a AgI colloid solution onto a quartz slide and then deoxidizes AgI to Ag nanoparticles on the substrate. The second approach (method 2) deoxidizes AgI to Ag nanoparticles in a colloid solution and then transfers the Ag nanoparticles capped by negatively charged mercaptoacetic acid onto a quartz slide. By transfer of the AgI/Ag nanoparticles from the colloid solutions to the solid substrates, the problem of instability of the colloid solutions can largely be overcome. The films thus prepared by both approaches retain the merits of metal colloid solutions while they discharge their shortcomings. Accordingly, the obtained Ag particle films are very suitable as SERS active substrates. SERS active substrates with different coverages can be formed in a layer-by-layer electrostatic assembly by exposing positively charged surfaces to the colloid solutions containing oppositely charged AgI/Ag nanoparticles. The SERS active substrates fabricated by the two novel methods have been characterized by means of atomic force microscopy (AFM) and ultraviolet-visible (UV-vis) spectroscopy. The results of AFM and UV-vis spectroscopy show that the Ag nanoparticles grow with the increase in the number of coverage and that most of them remain isolated even at high coverages. Consequently, the surface optical properties are dominated by the absorption due to the isolated Ag nanoparticles. The relationship between SERS intensity and surface morphology of the new active substrates has been investigated for Rhodamine 6G (R6G) adsorbed on them. It has been found that the SERS enhancement depends on the size and aggregation of the Ag particles on the substrates. Especially, we can obtain a stronger SERS signal from the substrate prepared by method 1, implying that for the metal nanoparticles capped with stabilizer molecules such as mercaptoacetic acid, the in situ deoxidization in the film is of great use in preparing SERS active substrates. Furthermore, we have found that the addition of Cl- into the AgI colloid solution changes the surface morphology of the SERS active substrates and favors stronger SERS enhancement.     

Oriented attachment-based assembly of dendritic silver nanostructures at room temperature

How particles aggregate into an interesting dendritic structure has been the object of research for many years because of its importance in understanding physical processes involved and in designing novel materials. In this work, we for the first time describe an oriented attachment-based assembly mechanism for formation of different types of dendritic silver nanostructures at room temperature. It is found that the concentration of both AgNO(3) and p-aminoazobenzene (PA) molecules has a significant effect on the formation and growth of these novel nanostructures. Characterization by transmission electron microscopy (TEM) clearly shows that the dendritic silver nanostructures can be obtained through the preferential oriented growth along a crystallographically special direction. Interestingly, we observe that the oriented attachment at room temperature can also take place between relatively large single-crystalline silver particles with a diameter range from 20 to 60 nm, which may provide a new possibility for the design of novel metal nanostructures by using large metal nanoparticles as building blocks at room temperature. Moreover, a surface-enhanced Raman scattering (SERS) technique is used to investigate the role of PA molecules during the growth of the dendritic silver nanostructures.     

Green Synthesis and Characterization of Silver Nanoparticles Using Ascomycota Fungi Penicillium nalgiovense AJ12

A new method for green synthesis of silver nanoparticles using the cell-free filtrate of Penicillium nalgiovense AJ12 as reducing and protecting agent was described. The pathway is based on the reduction of Ag¹⁺ by protein(s). Various techniques such as UV–Vis spectroscopy, transmission electron microscopy (TEM), dynamic light scattering (DLS), Fourier transform infrared and Zeta potential measurements were used to characterize the silver nanoparticle obtained. The results revealed synthesis of the spherical silver nanoparticles coated with protein(s). The average size of the particles obtained from TEM was 15.2 ± 2.6 nm. DLS measurements showed that the particle size was higher than that estimated from TEM measurements and was 25.2 ± 2.8 nm. Studies on the role of the cell-free filtrate proteins in the synthesis of silver nanoparticles indicated that the process is non-enzymatic but involves amino acids interactions with silver ions. It was found that the aqueous silver nanoparticles suspensions exhibited excellent stability over a wide range of ionic strength, pH and temperature.