金银纳米粒子的复合组装及表面增强拉曼光谱研究

采用自组装技术在硅基底上进行金银纳米粒子的混合组装, 通过控制组装溶液中金银溶胶的体积比而控制基底上金银纳米粒子的密度. SEM结果显示金银呈亚单层均匀分布, 以吡啶为探针分子, 在不同波长的激发光下研究了纯金、银以及混合组装时的SERS效应. 利用金银在不同激发线下增强效应的不同以及探针分子吸附在金银纳米粒子表面主要谱峰相对强度差别的特点, 通过一系列校正以及差谱方法研究了金银共存时SERS效应的变化, 并分离出混合体系中金的增强行为, 结果表明在金银同时组装时吡啶的SERS谱峰特征主要表现为银纳米粒子的行为, 分离出的金SERS光谱特征接近银的行为, 说明金银纳米粒子之间产生了一定的耦合作用.     

Au@SiO2核壳纳米粒子的制备及其表面增强拉曼光谱

采用柠檬酸钠还原氯金酸法制备金溶胶, 以正硅酸乙酯(TEOS)为硅源, 氨水作催化剂, 制备以金为核, 二氧化硅为壳的核壳纳米粒子. 金纳米粒子的粒径可以通过柠檬酸钠和氯金酸的比例控制, 通过调节TEOS的量和反应的时间可以控制二氧化硅壳层的厚度. 以苯硫酚为探针分子研究了核壳结构纳米粒子的表面增强拉曼散射(SERS)效应与二氧化硅壳层厚度之间的关系. 研究结果表明, 金内核电磁场增强效应随着二氧化硅壳层厚度的增加逐渐减弱, 且其衰减速度比具有相同尺度的双金属核壳结构纳米粒子的慢. 此外, 探针分子主要以物理作用吸附在二氧化硅的表面, 可通过洗涤方法将探针分子除去, 从而可使该复合结构基底用于循环SERS分析.     

Au-Ag三角纳米环单层膜的原位转化制备及 SERS效应

利用模板牺牲氧化还原反应将自组装在基片上的三角板银纳米粒子(边长约为79.2 nm)与氯金酸溶液作用进而原位转化形成三角纳米环. 通过紫外-可见(UV-Vis)光谱实时监测基片上银三角板纳米粒子在反应不同阶段的消光特性; 扫描电子显微镜(SEM)显示了银三角板纳米粒子转化过程的形貌变化; 利用X射线光电子能谱(XPS)对其成分进行分析. 表征结果表明, 三角纳米环的成分为Au-Ag合金或复合物; 随着基片与氯金酸溶液作用时间的增加, 自组装膜的表面等离子体共振峰逐渐红移; Au-Ag三角环状纳米粒子的平均壁厚度从29.3 nm缩小至16.2 nm. 以4-巯基苯胺(4-ATP)为探针分子研究了该Au-Ag三角环状纳米粒子单层膜的表面增强拉曼(SERS)活性. 自组装单层膜基底的SERS信号随着Au-Ag三角纳米环平均壁厚度的增加逐渐增强.     

基于Kretschmann结构的金银合金薄膜的SERS效应

利用Kretschmann棱镜耦合结构和532 nm激光光源,测试了金银合金薄膜的表面增强拉曼散射(SERS)效应,并与纯金薄膜的测试结果进行了比较.结果显示,在激发光为p偏振态且入射角近似等于表面等离子体共振(SPR)角时,附着于金银合金薄膜表面的Nile Blue分子的SERS信号达到最强,比利用纯金薄膜测得的SERS信号高约2倍.实验结果还表明,在金银合金薄膜表面自组装金纳米粒子后,Nile Blue吸附层的SERS信号比自组装纳米金之前测得的信号增强了至少3倍,比利用纳米金修饰的纯金薄膜测得的信号高出2倍多.在棱镜底面沿薄膜法线收集的SERS信号是完全非偏振光,而从棱镜侧面收集的SERS信号是p偏振光,是拉曼光借助SPR效应产生的定向发射.     

银纳米粒子簇的设计、 制备和表面增强拉曼光谱

通过匹配激光光斑直径与胶体微球的尺寸, 设计制备了银纳米粒子的表面增强拉曼散射(SERS)基底, 并将其用于研究单个银纳米粒子簇的表面增强拉曼光谱. 在制备纳米粒子的过程中, 考察了等离子体刻蚀时间与银沉积厚度对“单”银纳米粒子结构与形貌的影响. 将吡啶、 巯基苯和罗丹明R6G作为SERS探针分子, 研究了其SERS效应, 通过荧光共振能量转移(FRET)机理, 实现了染料分子在单银纳米粒子簇上的SERS效应. SERS光谱测试与相关计算结果表明, 单个银纳米粒子簇的拉曼增强因子能够达到约10⁶.     

利用去湿现象制备具有SERS活性的银纳米粒子图案

构建了具有表面增强拉曼散射(SERS)活性的二维有序环状与盘状的银纳米粒子结构, 利用CTAB包覆银纳米粒子的氯仿溶液直接在图案化的金基底上进行去湿, 当改变银纳米粒子的浓度时可以得到不同的图案. 利用原子力显微镜(AFM)对其结构进行了表征, 以4-巯基吡啶作为探针分子, 采用表面增强拉曼成像技术研究了这种基底的SERS活性, 这将为SERS的研究开拓新的领域.     

盐酸羟胺络合法制备银溶胶及表面增强拉曼基底

报道了一种制备银溶胶的新方法.用紫外-可见光谱和透射电镜研究了银纳米粒子的形成过程、粒子形状及粒径分布.紫外光谱结果表明,在还原剂中加入碘化银溶胶后立即形成银纳米粒子,开始时粒子的粒径较小,很快聚集成较大的粒子.随着反应的进行,较大的粒子又逐渐碎裂为较小的粒子.同时,粒子的粒径分布逐渐变窄,说明银纳米粒子的形成过程也是粒子粒径均化的过程.透射电镜的研究结果表明,银纳米粒子为形状均一的球形,平均粒径约35nm.将这种银纳米粒子转移到固体基片上可得到活性较高的表面增强拉曼(SERS)基底.     

Au-Ag合金纳米粒子制备及其表面增强拉曼光谱研究

首先采用柠檬酸钠法制得Au-Ag合金纳米种子, 然后采用盐酸羟胺生长法得到不同组成的Au-Ag合金纳米粒子. 在其UV-Vis光谱中只观察到一个位于单金属银和金之间的等离子体共振峰, 表明Au-Ag合金纳米粒子已经形成. TEM结果表明, 合金纳米粒子的粒径约为60 nm, 且颜色均一, 没有明显的核壳结构. 用苯硫酚(TP)作为探针分子研究了合金纳米粒子的表面增强拉曼光谱(SERS). 结果表明, SERS强度与合金纳米粒子的组成和尺寸有关. 当纳米粒子粒径一定时, 除Au25Ag75外, 随着金的增加SERS强度增强. Au25Ag75的粒径比Ag小, 导致SERS强度比Ag低. Au50Ag50和Au75Ag25加入TP分子后, 其聚集方式与Au相似, 等离子体共振峰逐渐靠近1064 nm, 金含量较高时, TP的SERS归于聚集体的等离子体共振增强的贡献.     

金@银核壳纳米粒子的制备和形貌的精确控制及其表面增强拉曼光谱性能

用种子生长法制备了金@银核壳结构的纳米粒子。在制备过程中通过控制氯金酸的浓度和硝酸银的体积,得到了不同粒径的金核和不同厚度的银壳构成的核壳纳米粒子。从而得到了具有不同SERS性能的金@银核壳纳米粒子。选取具有最佳SERS性能的金@银核壳纳米粒子实现了对罗丹明6G的微量检测。     

金@银核壳纳米粒子的制备和形貌的精确控制及其表面增强拉曼光谱性能

用种子生长法制备了金@银核壳结构的纳米粒子。在制备过程中通过控制氯金酸的浓度和硝酸银的体积,得到了不同粒径的金核和不同厚度的银壳构成的核壳纳米粒子。从而得到了具有不同SERS性能的金@银核壳纳米粒子。并选取具有最佳SERS性能的金@银核壳纳米粒子实现了对罗丹明6G的微量检测。     

The synthesis of translucent polymer nanolatexes via microemulsion polymerization

Surface-enhanced Raman scattering (SERS)-active substrates of polyvinyl alcohol/gold-silver (PVA/Au-Ag) nanofibers were prepared using a simple approach involving electrospinning. The tunable surface plasmon resonance (SPR) of gold-silver alloy (Au-Ag alloy) nanoparticles (NPs) was achieved by controlling the feed ratio between gold and silver precursors. A higher concentration of Au-Ag alloy NPs could be obtained than the conventional methods, using 1wt% of PVA as the stabilizer. The Au-Ag alloy structure was demonstrated by HRTEM and STEM-EDX. After the electrospinning, the Au-Ag alloy NPs were successfully embedded in PVA nanofibers, as shown in the SEM and TEM images. Raman spectra displayed an apparent enhancement in the signal of 4-mercaptobenzoic acid (4-MBA), pyridine, and thiophenol molecules pre-absorbed from their ethanol solution onto the PVA/Au-Ag nanofibers. Different SERS effects were achieved by varying the Au content or excitation wavelength.     

Synthesis of gold@carbon dots composite nanoparticles for surface enhanced Raman scattering

Gold@carbon dots composite nanoparticles (Au@CDs) with ultrathin carbon dot (CD) shells of ca. 2 nm were prepared by reducing HAuCl(4) with CDs at 100 °C. By adjusting the feeding mass ratio of HAuCl(4) to CDs, the average diameters of Au@CDs can be modulated from 8 to 44 nm. The suspension of Au@CDs with an average diameter of ca. 24 nm was applied as a substrate for surface enhanced Raman scattering (SERS) and it exhibited a higher SERS effect for rhodamine 6G (Rh6G) than the suspension of pure Au nanoparticles with nearly the same size. The excellent SERS effect of Au@CDs is mainly attributed to their improved capability of adsorbing the aromatic probe molecules.     

Synthesis of block copolymer-stabilized Au-Ag alloy nanoparticles and fabrication of poly(methyl methacrylate)/Au-Ag nanocomposite film

[Poly(2-(N,N-dimethylamino)ethyl methacrylate)]-b-poly(methyl methacrylate)-b-[poly(2-(N,N-dimethylamino)ethyl methacrylate)] (M(n)=45,000; 20K-5K-20K; PDI = 1.2) block copolymer surfactant stabilized amphiphilic gold-silver alloy nanoparticles (Au-Ag(PDMA-b-PMMA-b-PDMA)) has been synthesized in both water and in organic medium. The block copolymer stabilized pre-made alloy nanoparticles were successfully dispersed in hydrophobic poly(methyl methacrylate) homopolymer matrix (PMMA) of molecular weight 30,000. The successful synthesis of alloy nanoparticles was accessed by Transmission Electron Microscope (TEM), Energy Dispersed X-ray (EDX), and UV-visible spectrophotometric analysis. The surface functionality of the nanoparticles was confirmed by quantitative determining the grafting density of polymer chain around the nanoparticle surface using combination of thermo gravimetric (TGA) and TEM analysis. The hydrodynamic diameter of the alloy particles including the polymer chains was obtained from dynamic light scattering measurement (DLS). The mechanism of synthesis of high concentration of Au-Ag alloy particles from HAuCl(4) and AgNO(3) (in presence of Cl(-) from reduction of gold salt) metal particles precursors and the successful preparation of poly(methyl methacrylate)/gold-silver nanocomposite films have been discussed.     

Synthesis, characterization and SERS activity of Au-Ag nanorods

The formation mechanism and morphology of Au-Ag bimetallic colloidal nanoparticles depend on the composition. Ag coated Au colloidal nanoparticles have been prepared by deposition of Ag through chemical reduction on performed Au colloid. The composition of the Au(100-x)-Ag(x) particles was varied from x=0 to 50. The obtained colloids were characterized by UV-vis spectroscopy and transmission electron microscopy (TEM). The Au(80)-Ag(20) colloid consists of alloy nanorods with dimension of 25nmx100nm. The activity of these nanorods in surface enhanced Raman spectroscopy (SERS) was checked by using sodium salicylate as an adsorbate probe. Intense SERS bands are observed indicating its usefulness as a SERS substrate in near infrared (NIR) laser excitation.     

室温电子还原制备金纳米颗粒与琼脂糖复合膜的表征与应用

利用室温电子还原技术合成了一种金纳米颗粒与琼脂糖复合膜。合成过程采用氩气辉光放电为廉价电子源,方便快捷,绿色环保。通过紫外-可见(UV-Vis)分光光度计、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、X射线衍射(XRD)仪、光电子能谱(XPS)等表征,发现可以通过改变氯金酸浓度调控复合膜中金纳米颗粒的分布,加入聚乙烯吡咯烷酮(PVP)可有效控制金纳米颗粒的形貌。由于复合膜具有金纳米颗粒密集排布的结构,可作为表面增强拉曼散射(SERS)活性基底。实验表明,以对氨基苯硫酚为探针,该复合膜作为SERS基底,SERS平均增强因子超过了106,检测限达到了10-12mol?L-1。除此之外,作为SERS基底,复合膜具有良好的均一性和稳定性。     

Differential SERS activity of gold and silver nanostructures enabled by adsorbed poly(vinylpyrrolidone)

We report that poly(vinylpyrrolidone) (PVP), a common stabilizer of colloidal dispersions of noble metal nanostructures, has a dramatic effect on their surface-enhanced Raman scattering (SERS) activity and enables highly selective SERS detection of analytes of various type and charge. Nanostructures studied include PVP-stabilized Au-Ag nanoshells synthesized by galvanic exchange reaction of citrate-reduced Ag nanoparticles (NPs), as well as solid citrate-reduced Ag and Au NPs, both before and after stabilization with PVP. All nanostructures were characterized in terms of their size, surface plasmon resonance wavelength, surface charge, and chemical composition. While the SERS activities of the parent citrate-reduced Ag and Au NPs are similar for rhodamine 6G (R6G) and 1,2-bis(4-pyridyl)ethylene (BPE) at various pH values, PVP-stabilized nanostructures demonstrate large differences in SERS enhancement factors (EFs) between these analytes depending on their chemical nature and protonation state. At pH values higher than BPE's pK(a2) of 5.65, where the analyte is largely unprotonated, the PVP-coated Au-Ag nanoshells showed a high SERS EF of >10(8). In contrast, SERS EFs were 10(3)- to 10(5)-fold lower for the protonated form of BPE at lower pH values, or for the usually highly SERS-active cationic R6G. The differential SERS activity of PVP-stabilized nanostructures is a result of discriminatory binding of analytes within-adsorbed PVP monolayer and a subsequent increase of analyte concentration at the nanostructure surface. Our experimental and theoretical quantum chemical calculations show that BPE binding with PVP-stabilized Au-Ag nanoshells is stronger when the analyte is in its unprotonated form as compared to its cationic, protonated form at a lower pH.     

Sonoelectrochemical synthesis of spike-like gold-silver alloy nanoparticles from bulk substrates and the application on surface-enhanced Raman scattering

The synthesis of non-spherical spike-like gold-silver alloy nanoparticles on platinum substrates was first developed by sonoelectrochemical methods in this study. First, a silver substrate was roughened by a triangular-wave oxidation-reduction cycle (ORC) in an aqueous solution containing 0.1 M HCl. Silver-containing complexes were found in the solution after the ORC treatment. Then a gold substrate was subsequently roughened by the similar ORC treatment in the same silver complexes-containing solution. After this procedure, Au- and Ag-containing complexes were left in the solution. Subsequently, the Au working electrode was immediately replaced by a Pt electrode. A cathodic overpotential was applied under controlled sonication and slight stirring to synthesize Au-Ag alloy nanoparticles on the Pt substrate. Encouragingly, the surface-enhanced Raman scattering (SERS) of Rhodamine 6G on the Au-Ag alloy nanoparticles-deposited Pt substrate exhibits a higher intensity by eight-fold of magnitude and a better resolution, as compared to that obtained on the Au nanoparticles-deposited Pt substrate.     

Synergistic effect in an Au-Ag alloy nanocatalyst: CO oxidation

Au-Ag alloy nanoparticles supported on mesoporous aluminosilicate have been prepared by one-pot synthesis using hexadecyltrimethylammonium bromide (CTAB) both as a stabilizing agent for nanoparticles and as a template for the formation of mesoporous structure. The formation of Au-Ag alloy nanoparticles was confirmed by X-ray diffraction (XRD), ultraviolet-visible (UV-vis) spectroscopy, and transmission electron microscopy (TEM). Although the Au-Ag alloy nanoparticles have a larger particle size than the monometallic gold particles, they exhibited exceptionally high activity in catalysis for low-temperature CO oxidation. Even at a low temperature of 250 K, the reaction rate can reach 8.7 x 10(-6) mol.g(cat.)(-1).s(-1) at an Au/Ag molar ratio of 3/1. While neither monometallic Au@MCM-41 nor Ag@MCM-41 shows activity at this temperature, the Au-Ag alloy system shows a strongly synergistic effect in high catalytic activity. In this alloy system, the size effect is no longer a critical factor, whereas Ag is believed to play a key role in the activation of oxygen.