碱金属和碱土金属促进的Ni/SiO2催化剂上甲烷的二氧化碳重整制合成气

Ni/SiO2 catalysts promoted by alkali metals K and Cs or alkaline earth metals Mg, Ca, Sr and Ba were prepared, characterized by H2-TPR and XRD, and used for the production of synthesis gas via methane reforming with CO2. Though K and Cs promoted Ni catalysts could eliminate coke deposition, the reforming activity of these promoted catalysts was decreased heavily. Mg and Ca promoted Ni/SiO2 catalysts exhibited excellent coke resistance ability with minor loss of the reforming activity of Ni/SiO2. Ba showed poor coke resistance ability and small amount of Sr increased the formation of coke. The possible mechanism of these promoters was discussed.     

Highly effective methane conversion to aromatic hydrocarbons by means of microwave and rf-induced catalysis

Conversion of methane to higher hydrocarbon products, in particular, aromatic hydrocarbons has been achieved with good methane conversion and selectivity to aromatic products over heterogeneous catalysts using both high power pulsed microwave and rf energy. For example, under microwave irradiation > 85% conversion of methane and 60% selectivity to aromatics could be achieved. Cu, Ni, Fe and Al metallic materials are highly effective catalysts for the aromatization of methane via microwave heating; however, with a variety of supported catalysts the major products were C₂ hydrocarbons and the conversion of methane was low. The use of sponge, wire and net forms of these metal catalysts was found advantageous in effective methane conversion. The reactions are considered to be free radical in nature and to proceed through an intermediate stage involving formation of acetylene. The influence of catalyst nature and configuration, as well as the microwave and rf irradiation parameters on the reaction efficiency and product selectivity has been examined in both batch and continuous flow conditions.     

Catalytic Oxidation of Methane by Nitrous Oxide on H[Al]ZSM-5 Zeolite, Silicalite, and Amorphous SiO2 Modified by Iron, Silver, and Gadolinium Ions

Methane oxidation by an excess of N₂O on the catalytic sites formed in HZSM-5 zeolite, silicalite, and SiO₂ after modification with iron, silver, and gadolinium cations in different combinations is studied. Introduction of iron and silver ions into H[Al]ZSM-5 zeolite is shown to result in the formation of the sites that are active in methane oxidation, while the systems obtained on the basis of crystalline silicalite or amorphous SiO₂ demonstrate poor or no catalytic activity, respectively. Complete oxidation of methane with 100% conversion is observed on the Fe/HZSM-5 and Ag/HZSM-5 catalysts at temperatures higher than 350 and 450°C, respectively. A decrease in the reaction temperature and in the methane conversion is accompanied by coking of the catalysts and, in the case of Fe/HZSM-5, by the appearance of trace amounts of methanol and formic acid in the gas phase. The temperature dependence of the activity and selectivity for the Ag/HZSM-5 and (Ag + Gd)/HZSM-5 catalysts exhibits a pronounced hysteresis at 330–480°C, and the formation of coke proceeds much faster than in the case of iron-containing samples. Catalytic properties of (Fe + Ag)/HZSM-5 are similar to those of Fe/HZSM-5. The introduction of Gd does not influence significantly the activity and selectivity of the catalysts. ESR and TG–DTA were used to determine the state and distribution of Fe, Ag, and Gd in the samples and to examine the processes of coke formation.     

Direct Non‐Oxidative Methane Conversion in a Millisecond Catalytic Wall Reactor

Direct non‐oxidative methane conversion (DNMC) has been recognized as a single‐step technology that directly converts methane into olefins and higher hydrocarbons. High reaction temperature and low catalyst durability, resulting from the endothermic reaction and coke deposition, are two main challenges. We show that a millisecond catalytic wall reactor enables stable methane conversion, C₂₊ selectivity, coke yield, and long‐term durability. These effects originate from initiation of the DNMC on a reactor wall and maintenance of the reaction by gas‐phase chemistry within the reactor compartment. The results obtained under various temperatures and gas flow rates form a basis for optimizing the process towards lighter C₂ or heavier aromatic products. A process simulation was done by Aspen Plus to understand the practical implications of this reactor in DNMC. High carbon and thermal efficiencies and low cost of the reactor materials are realized, indicating the technoeconomic viability of this DNMC technology.     

Selective Coke Combustion by Oxygen Pulsing During Mo/ZSM‐5‐Catalyzed Methane Dehydroaromatization

Non‐oxidative methane dehydroaromatization is a promising reaction to directly convert natural gas into aromatic hydrocarbons and hydrogen. Commercialization of this technology is hampered by rapid catalyst deactivation because of coking. A novel approach is presented involving selective oxidation of coke during methane dehydroaromatization at 700 °C. Periodic pulsing of oxygen into the methane feed results in substantially higher cumulative product yield with synthesis gas; a H₂/CO ratio close to two is the main side‐product of coke combustion. Using ¹³C isotope labeling of methane it is demonstrated that oxygen predominantly reacts with molybdenum carbide species. The resulting molybdenum oxides catalyze coke oxidation. Less than one‐fifth of the available oxygen reacts with gaseous methane. Combined with periodic regeneration at 550 °C, this strategy is a significant step forward, towards a process for converting methane into liquid hydrocarbons.     

Conversion of natural gas to C2 hydrocarbons through dielectric-barrier discharge plasma catalysis

The experiments are carried out in the system of continuous flow reactors with dielectric-barrier discharge (DBD) for studies on the conversion of natural gas to C₂ hydrocarbons through plasma catalysis under the atmosphere pressure and room temperature. The influence of discharge frequency, structure of electrode, discharge voltage, number of electrode, ratio of H₂/CH₄, flow rate and catalyst on conversion of methane and selectivity of C₂ hydrocarbons are investigated. At the same time, the reaction process is investigated. Higher conversion of methane and selectivity of C₂ hydrocarbons are achieved and deposited carbons are eliminated by proper choice of parameters. The appropriate operation parameters in dielectric-barrier discharge plasma field are that the supply voltage is 20–40 kV (8.4–40 W), the frequency of power supply is 20 kHz, the structure of (b) electrode is suitable, and the flow of methane is 20–60 mL · min⁻¹. The conversion of methane can reach 45%, the selectivity of C₂ hydrocarbons is 76%, and the total selectivity of C₂ hydrocarbons and C₃ hydrocarbons is nearly 100%. The conversion of methane increases with the increase of voltage and decreases with the flow of methane increase; the selectivity of C₂ hydrocarbons decreases with the increase of voltage and increases with the flow of methane increase. The selectivity of C₂ hydrocarbons is improved with catalyst for conversion of natural gas to C₂ hydrocarbons in plasma field. Methane molecule collision with radicals is mainly responsible for product formation.     

Effect of Brønsted/Lewis Acid Ratio on Conversion of Sugars to 5‐Hydroxymethylfurfural over Mesoporous Nb and Nb‐W Oxides

A series of mesoporous Nb and Nb‐W oxides were employed as highly active solid acid catalysts for the conversion of glucose to 5‐hydroxymethylfurfural (HMF ). The results of solid state ³¹P MAS NMR spectroscopy with adsorbed trimethylphosphine as probe molecule show that the addition of W in niobium oxide increases the number of Brønsted acid sites and decreases the number of Lewis acid sites. The catalytic performance for Nb‐W oxides varied with the ratio of Brønsted to Lewis acid sites and high glucose conversion was observed over Nb₅W₅ and Nb₇W₃ oxides with high ratios of Brønsted to Lewis acid sites. All Nb‐W oxides show a relatively high selectivity of HMF , whereas no HMF forms over sulfuric acid due to its pure Brønsted acidity. The results indicate fast isomerization of glucose to fructose over Lewis acid sites followed by dehydration of fructose to HMF over Brønsted acid sites. Moreover, comparing to the reaction occurred in aqueous media, the 2‐butanol/H₂O system enhances the HMF selectivity and stabilizes the activity of the catalysts which gives the highest HMF selectivity of 52% over Nb₇W₃ oxide. The 2‐butanol/H₂O catalytic system can also be employed in conversion of sucrose, achieving HMF selectivity of 46% over Nb₅W₅ oxide.     

Reversible Nature of Coke Formation on Mo/ZSM‐5 Methane Dehydroaromatization Catalysts

Non‐oxidative dehydroaromatization of methane over Mo/ZSM‐5 zeolite catalysts is a promising reaction for the direct conversion of abundant natural gas into liquid aromatics. Rapid coking deactivation hinders the practical implementation of this technology. Herein, we show that catalyst productivity can be improved by nearly an order of magnitude by raising the reaction pressure to 15 bar. The beneficial effect of pressure was found for different Mo/ZSM‐5 catalysts and a wide range of reaction temperatures and space velocities. High‐pressure operando X‐ray absorption spectroscopy demonstrated that the structure of the active Mo‐phase was not affected by operation at elevated pressure. Isotope labeling experiments, supported by mass‐spectrometry and ¹³C nuclear magnetic resonance spectroscopy, indicated the reversible nature of coke formation. The improved performance can be attributed to faster coke hydrogenation at increased pressure, overall resulting in a lower coke selectivity and better utilization of the zeolite micropore space.     

A Versatile Iron–Tannin‐Framework Ink Coating Strategy to Fabricate Biomass‐Derived Iron Carbide/Fe‐N‐Carbon Catalysts for Efficient Oxygen Reduction

The conversion of biomass into valuable carbon composites as efficient non‐precious metal oxygen‐reduction electrocatalysts is attractive for the development of commercially viable polymer electrolyte membrane fuel‐cell technology. Herein, a versatile iron–tannin‐framework ink coating strategy is developed to fabricate cellulose‐derived Fe₃C/Fe‐N‐C catalysts using commercial filter paper, tissue, or cotton as a carbon source, an iron–tannin framework as an iron source, and dicyandiamide as a nitrogen source. The oxygen reduction performance of the resultant Fe₃C/Fe‐N‐C catalysts shows a high onset potential (i.e. 0.98 V vs the reversible hydrogen electrode (RHE)), and large kinetic current density normalized to both geometric electrode area and mass of catalysts (6.4 mA cm^?2 and 32 mA mg^?1 at 0.80 V vs RHE) in alkaline condition. This method can even be used to prepare efficient catalysts using waste carbon sources, such as used polyurethane foam.     

Epoxidation of cyclohexene with H2O2 over efficient water‐tolerant heterogeneous catalysts composed of mono‐substituted phosphotungstic acid on co‐functionalized SBA‐15

A series of Keggin‐type heteropolyacid‐based heterogeneous catalysts (Co‐/Fe‐/Cu‐POM‐octyl‐NH₃‐SBA‐15) were synthesized via immobilized transition metal mono‐ substituted phosphotungstic acids (Co‐/Fe‐/Cu‐POM) on octyl‐amino‐co‐functionalized mesoporous silica SBA‐15 (octyl‐NH₂‐SBA‐15). Characterization results indicated that Co‐/Fe‐/Cu‐POM units were highly dispersed in mesochannels of SBA‐15, and both types of Brønsted and Lewis acid sites existed in Co‐/Fe‐/Cu‐POM‐octyl‐NH₃‐SBA‐15 catalysts. Co‐POM‐octyl‐NH₃‐SBA‐15 catalyst showed excellent catalytic performance in H₂O₂‐mediated cyclohexene epoxidation with 83.8% of cyclohexene conversion, 92.8% of cyclohexene oxide selectivity, and 98/2 of epoxidation/allylic oxidation selectivity. The order of catalytic activity was Co‐POM‐octyl‐NH₃‐SBA‐15 > Fe‐POM‐octyl‐NH₃‐SBA‐15 > Cu‐POM‐octyl‐NH₃‐SBA‐15. In order to obtain insights into the role of ‐octyl moieties during catalysis, an octyl‐free catalyst (Co‐POM‐NH₃‐SBA‐15) was also synthesized. In comparison with Co‐POM‐NH₃‐SBA‐15, Co‐POM‐octyl‐NH₃‐SBA‐15 showed enhanced catalytic properties (viz. activity and selectivity) in cyclohexene epoxidation. Strong chemical bonding between ‐NH₃⁺ anchored on the surface of SBA‐15 and heteropolyanions resulted in excellent stability of Co‐POM‐octyl‐NH₃‐SBA‐15 catalyst, and it could be reused six times without considerable loss of activity.     

Effect of weak base modification on ZSM‐5 catalyst for methanol to aromatics

The effect of weak base modification on the catalytic performance of ZSM‐5 catalyst for conversion of methanol to aromatics was investigated. The catalysts were characterized using X‐ray diffraction, X‐ray fluorescence, N₂ adsorption–desorption, NH₃ temperature‐programmed desorption, Fourier transform infrared spectroscopy, scanning electron microscopy and thermogravimetry. The results showed that catalysts treated with weak base (NaHCO₃, Na₂CO₃ and NH₃⋅H₂O) exhibited a pore structure with interconnected micropores and mesopores. The existence of mesopores was beneficial for improving the diffusion of reactants and products, and the coke deposition resistance capacity of treated catalysts was enhanced greatly. Meanwhile, compared to traditional ZSM‐5 zeolite, the ratio of Brønsted to Lewis (B/L) acid sites of ZSM‐5/NH₃⋅H₂O (B/L = 7.35) zeolite slightly increased but the amount of acid sites reduced, while those of ZSM‐5/NaHCO₃ (B/L = 0.127) and ZSM‐5/Na₂CO₃ (B/L = 0.107) significantly reduced. Further, the catalyst treated with NH₃⋅H₂O solution was evaluated in the methanol to aromatics reaction and led to an enhanced aromatization reaction rate. The liquid hydrocarbons product distribution exhibited higher aromatic hydrocarbons yield (56.12%) and selectivity (40.28%) of benzene, toluene and xylene (BTX) with isoparaffin content reducing to 26.17%, which could be explained by appropriate B/L acid sites ratio, higher pore volumes and higher surface area.     

Synthesis of a Tweezer—like Bis（Phenylthiapropoxy）calix[4]—arene as a Cation／π Enhanced Sensor for Ion—Selective Electrodes

Two novel 25,27-dihydroxy-26,28-bis(3-phenylthiapropxy)-calix[4]arene(3) and 25,27-dihydroxy-26,28-bis(3-phenylthiapropoxy)-5,11,17,23-tetra-tert-butylcalix[4] arene (4) were synthesized for the evaluation of their ion-selectivity in ion-selective electrodes(ISEs).ISEs based on 3 and 4 as neutral ionophores were prepared,and their selectivity coefficients for Ag^ (lg KAg,M^pot)were investigated against other alkali metal,alkaline-earth metal,aluminum,thallium(Ⅰ）,Lead and some transition metal ions using the separate solution method (SSM).These ISEs showed excellent Ag^ seletivity over most of the interfering cations examined,except for Hg^2 and Fe^2 having relative smaller interference(lg KAg,M^pot≤-2.1).     

C−C Bond Formation in Syngas Conversion over Zinc Sites Grafted on ZSM‐5 Zeolite

Despite significant progress achieved in Fischer–Tropsch synthesis (FTS) technology, control of product selectivity remains a challenge in syngas conversion. Herein, we demonstrate that Zn²⁺‐ion exchanged ZSM‐5 zeolite steers syngas conversion selectively to ethane with its selectivity reaching as high as 86 % among hydrocarbons (excluding CO₂) at 20 % CO conversion. NMR spectroscopy, X‐ray absorption spectroscopy, and X‐ray fluorescence indicate that this is likely attributed to the highly dispersed Zn sites grafted on ZSM‐5. Quasi‐in‐situ solid‐state NMR, obtained by quenching the reaction in liquid N₂, detects C₂ species such as acetyl (‐COCH₃) bonding with an oxygen, ethyl (‐CH₂CH₃) bonding with a Zn site, and epoxyethane molecules adsorbing on a Zn site and a Brønsted acid site of the catalyst, respectively. These species could provide insight into C?C bond formation during ethane formation. Interestingly, this selective reaction pathway toward ethane appears to be general because a series of other Zn²⁺‐ion exchanged aluminosilicate zeolites with different topologies (for example, SSZ‐13, MCM‐22, and ZSM‐12) all give ethane predominantly. By contrast, a physical mixture of ZnO‐ZSM‐5 favors formation of hydrocarbons beyond C₃₊. These results provide an important guide for tuning the product selectivity in syngas conversion.     

Non-oxidative conversion of methane into various petrochemical grades over tunable tri-metallic Fe-W-Mo/HZSM-5 catalyst systems

Most mono-metallic catalysts applied in non-oxidative conversion of methane exhibit low catalyst activity and limited selectivity towards useful petrochemicals. In this study, a series of thermally stable and tunable 5.4 wt% metal/support Fe-W-Mo/HZSM-5 catalyst systems were synthesized, characterized, and applied in non-oxidative conversion of methane in a custom-made stainless-steel reactor at various process conditions. Analysis of products from the reactor was done using Shimadzu 2014 gas chromatograph. Varying the amount of Fe, W, and Mo on HZSM-5 greatly influenced catalyst activity in terms of methane conversion and product distribution. When the quantities of Fe and W were increased to 2.25 wt% each and the quantity of molybdenum reduced to 0.9 wt% in the overall 5.4 wt% metal/ HZSM-5 catalyst, the resultant catalyst system became most active in methane conversion (17.4%) at 800 °C. Reducing the quantity of Fe and W each to 1.35 wt% and increasing Mo to 2.7 wt% in the overall 5.4 wt% catalyst, the resultant catalyst system became less selective towards C₂ hydrocarbons and coke, but highly selective towards xylene and benzene. Therefore, this study demonstrates that varying metal loading presents an opportunity to tune the 5.4 wt% binary Fe, W, and Mo on HZSM-5 to achieve desired methane conversion and product distribution.     

Highly Tunable Selectivity for Syngas‐Derived Alkenes over Zinc and Sodium‐Modulated Fe5C2 Catalyst

Zn‐ and Na‐modulated Fe catalysts were fabricated by a simple coprecipitation/washing method. Zn greatly changed the size of iron species, serving as the structural promoter, while the existence of Na on the surface of the Fe catalyst alters the electronic structure, making the catalyst very active for CO activation. Most importantly, the electronic structure of the catalyst surface suppresses the hydrogenation of double bonds and promotes desorption of products, which renders the catalyst unexpectedly reactive toward alkenes—especially C₅₊ alkenes (with more than 50% selectivity in hydrocarbons)—while lowering the selectivity for undesired products. This study enriches C₁ chemistry and the design of highly selective new catalysts for high‐value chemicals.     

Vapor‐Phase Reaction of Citronellal over Mesoporous Molecular Sieves MCM‐41 and Zeolites

The vapor‐phase reaction of citronellal (CTN) at 220 °C and atmospheric pressure has been studied using mesoporous molecular sieves and zeolites in a fixed‐bed reactor. The primary products included isopulegol (IPG), menthone, and pulegol with subsequent reactions to form cyclic hydrocarbons. The CTN conversion and the product selectivity depend on the acidity and the textural property of catalysts. Lewis and/or Brönsted acid sites are essential for catalyzing this reaction. An increase of SiO₂/Al₂O₃ mol ratio diminishes the acid amount of all catalysts and enhances both the surface area and the structural order of MCM‐41. The catalytic activity follows the order of MCM‐41 > HZSM‐5 > Hβ > USY, in accordance with the relative total acid amount except that of MCM‐41. Despite its low acidity, Si‐MCM‐41 exhibits the best catalytic performance due to its uniform mesopores, large surface area and good stability; the CTN conversion and the IPG yield attain 91.9% and 58.6%, respectively, after at least 25 h time‐on‐stream.     

Adsorptive Separation of Acetylene from Light Hydrocarbons by Mesoporous Iron Trimesate MIL‐100(Fe)

A reducible metal–organic framework (MOF), iron(III) trimesate, denoted as MIL‐100(Fe), was investigated for the separation and purification of methane/ethane/ethylene/acetylene and an acetylene/CO₂ mixtures by using sorption isotherms, breakthrough experiments, ideal adsorbed solution theory (IAST) calculations, and IR spectroscopic analysis. The MIL‐100(Fe) showed high adsorption selectivity not only for acetylene and ethylene over methane and ethane, but also for acetylene over CO₂. The separation and purification of acetylene over ethylene was also possible for MIL‐100(Fe) activated at 423 K. According to the data obtained from operando IR spectroscopy, the unsaturated Fe^III sites and surface OH groups are mainly responsible for the successful separation of the acetylene/ethylene mixture, whereas the unsaturated Fe^II sites have a detrimental effect on both separation and purification. The potential of MIL‐100(Fe) for the separation of a mixture of C₂H₂/CO₂ was also examined by using the IAST calculations and transient breakthrough simulations. Comparing the IAST selectivity calculations of C₂H₂/CO₂ for four MOFs selected from the literature, the selectivity with MIL‐100(Fe) was higher than those of CuBTC, ZJU‐60a, and PCP‐33, but lower than that of HOF‐3.     

A Graphene‐Supported Single‐Atom FeN5 Catalytic Site for Efficient Electrochemical CO2 Reduction

Electrochemical conversion of CO₂ into valued products is one of the most important issues but remains a great challenge in chemistry. Herein, we report a novel synthetic approach involving prolonged thermal pyrolysis of hemin and melamine molecules on graphene for the fabrication of a robust and efficient single‐iron‐atom electrocatalyst for electrochemical CO₂ reduction. The single‐atom catalyst exhibits high Faradaic efficiency (ca. 97.0 %) for CO production at a low overpotential of 0.35 V, outperforming all Fe‐N‐C‐based catalysts. The remarkable performance for CO₂‐to‐CO conversion can be attributed to the presence of highly efficient singly dispersed FeN₅ active sites supported on N‐doped graphene with an additional axial ligand coordinated to FeN₄. DFT calculations revealed that the axial pyrrolic nitrogen ligand of the FeN₅ site further depletes the electron density of Fe 3d orbitals and thus reduces the Fe–CO π back‐donation, thus enabling the rapid desorption of CO and high selectivity for CO production.     

Promotion of cobalt catalysts for the Fischer-Tropsch synthesis with alkali metals

The promotion of supported cobalt catalysts for the synthesis of hydrocarbons from CO and H₂ with alkali metals was studied. The catalysts were characterized by X-ray diffraction analysis, oxygen titration, and the temperature-programmed desorption (TPD) of CO. Catalytic tests showed that the introduction of alkaline promoters increases selectivity for higher hydrocarbons, decreases selectivity for methane, and also increases the concentration of olefins in the gasoline fraction of products. The promoting effect depends on the catalyst preparation method. The TPD of CO was used to demonstrate that the greatest amount of CO was adsorbed on the surface of a catalyst promoted with potassium; in this case, the strength of CO binding on this catalyst reached a maximum. The data of the TPD of CO correspond to the highest selectivity of a cobalt-potassium catalyst for the formation of higher hydrocarbons.     

Efficient Non‐dissociative Activation of Dinitrogen to Ammonia over Lithium‐Promoted Ruthenium Nanoparticles at Low Pressure

There is an exciting possibility to decentralize ammonia synthesis for fertilizer production or energy storage without carbon emission from H₂ obtained from renewables at small units operated at lower pressure. However, no suitable catalyst has yet been developed. Ru catalysts are known to be promoted by heavier alkali dopants. Instead of using heavy alkali metals, Li is herein shown to give the highest rate through surface polarisation despite its poorest electron donating ability. This exceptional promotion rate makes Ru–Li catalysts suitable for ammonia synthesis, which outclasses industrial Fe counterparts by at least 195 fold. Akin to enzyme catalysis, it is for the first time shown that Ru–Li catalysts hydrogenate end‐on adsorbed N₂ stabilized by Li⁺ on Ru terrace sites to ammonia in a stepwise manner, in contrast to typical N₂ dissociation on stepped sites adopted by Ru–Cs counterparts, giving new insights in activating N₂ by metallic catalysts.