A位取代对(Ca0.61Nd0.26)TiO3陶瓷烧结特性和介电性能的影响

采用常规固相反应法,以(Ca0.61Nd0.26)TiO3体系为基体成分,研究了A位取代对(Ca0.61Nd0.26)TiO3陶瓷的烧结特性和介电性能的影响规律。结果表明:Zn,Mg的A位取代,促使(Ca0.61Nd0.26)TiO3陶瓷烧结温度从1350℃降至1250℃。Zn,Mg在一定范围内A位取代(Ca0.61Nd0.26)TiO3中的Ca可形成钙钛矿结构的固溶体,Zn、Mg最大固溶度(x(Zn),y(Mg))分别不超过0.1和0.15mol。当取代量超过固溶度后,分别形成Ca2Zn4Ti15O36和MgTi2O5第二相。随Zn和Mg取代量的增加,陶瓷介电常数(εr)和谐振频率温度系数(τf)减小。陶瓷品质因数(Qf)值随Zn取代量先增后减,而随Mg取代量增加,其Qf值一直增大。Zn,Mg最佳取代分别为x(Zn)=0.15和y(Mg)=0.25,在1250℃烧结2h,[(Ca0.85Zn0.15)0.61Nd0.26]TiO3的介电性能:εr=93.60,Qf=12454GHz,τf= 150.3ppm·℃-1,[(Ca0.75Mg0.25)0.61Nd0.26]TiO3的介电性能:εr=72.48,Qf=14622GHz,τf= 108ppm·℃-1。     

预烧温度对CaO-Li_2O-Sm_2O_3-TiO_2微波介质陶瓷介电性能的影响

用固相反应法制备了CaO-Li2O-Sm2O3-TiO2(CLST)微波介质陶瓷。通过改变预烧温度(1 000~1 200℃)研究其对CLST微波介质陶瓷介电性能的影响。研究过程中,对预烧粉体与烧结陶瓷进行XRD与SEM分析,对陶瓷的介电性能εr、Q、τf进行了测试。结果表明,预烧温度对CLST微波介质陶瓷介电性能有较大影响,在预烧温度1 150℃,烧结温度1 340℃时可获得较好的介电性能:εr=112,Q=845,τf=52×10-6/℃。     

低温烧结NaBi(WO4)2陶瓷的介电性能

采用固相合成法制备了（WO₄）₂（NBW）陶瓷，研究了NBW陶瓷的相结构、形貌、烧结特性和微波介电性能。NBW陶瓷在625~800℃烧结1~4 h能够致密化。X射线衍射表明在625~800℃烧结2 h的NBW陶瓷均为四方晶系白钨矿结构的单相陶瓷。随着烧结温度的提高，NBW陶瓷的介电常数、品质因数（Qf值）先增加后降低，谐振频率温度系数逐渐降低。经650℃烧结2 h获得的NBW陶瓷的介电常数为14.36，Qf值为16 503 GHz，谐振频率温度系数为-1.055×10-5℃^-1。NBW陶瓷与银共烧反应生成Ag₂W₂O₇相，而与Au、Al共烧具备化学兼容性。     

单相Ba2Ti9O20柠檬酸凝胶法制备、表征及介电性能

采用柠檬酸凝胶法两步热处理工艺制备了单相Ba₂Ti₉O₂₀。干凝胶在750 ℃热处理得到了物相为BaTi₅O₁₁和Ba₄Ti₁₃O₃₀、尺寸为30～50 nm的前驱体粉体。纳米前驱体具有高表面活性，促使单相Ba₂Ti₉O₂₀在1 200 ℃热处理温度下形成。两步热处理所得的粉体比一步热处理所得的粉体具有更好的烧结和介电特性，两步热处理所得的粉体，在1 250 ℃烧结4 h，可获得理论密度为97%的Ba₂Ti₉O₂₀微波介质陶瓷，其介电性能：ε_r=38.5，Qf=19 320 GHz，τ_f=8.7×10^-6 ℃^-1。     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃‐Bi₂O₃‐ZnO‐Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1364,介电损耗低至1.2%。     

纳米CaMgSi2O6粉体的低温合成与微波介电性能

以硝酸锂、偏钒酸铵、硝酸钙、硝酸镁、正硅酸乙酯为原料，采用溶胶-凝胶法低温合成纳米CaMgSi₂O₆微波介质陶瓷粉体，研究了不同粒径粉体的烧结行为与微波介电性能。结果表明，通过在钙镁硅溶胶中引入锂钒烧结助剂可大大降低陶瓷粉体的晶相合成温度，干凝胶在750 ℃煅烧后可获得主晶相为CaMgSi₂O₆、分散性良好、粒径为78～98 nm的陶瓷粉体，可满足微型片式元器件用超薄陶瓷介质层的制备要求;该粉体在890 ℃烧结后获得致密结构的陶瓷，具有良好的微波介电性能:介电常数为7.68，品质因数为24 542 GHz，频率温度系数为-57.25×10^-6 ℃^-1。     

ZrO2添加对BaO-La2O3-TiO2介质陶瓷介电性能的影响

BaO-La2O3-TiO2(BLT)是典型的高介电常数微波介质陶瓷,其作为微波谐振器与滤波器的关键材料,在微波通讯技术上有着重要的应用. 选用ZrO2对BLT进行改性研究,当ZrO2的加入量z＜0.5mol时,烧结体的主晶相为Ba6-3xLa8 2x(Ti1-zZrz)18O54(x=1/2)钨青铜结构(TB)固溶体,随ZrO2加入量的增多,烧结体中产生第二相,当z＝1.0mol时,烧结体的主晶相为La2Zr2O7和BaZrO3,这与结构许容因子的变化密切相关,获得较优介电性能如下εr=103.71,Q·f=4862.53 GHz,τf=168.97×10-6/℃,优于不添加ZrO2时烧结体介电性能(εr=139.73,Q·f=1238.96 GHz,τf=179.97×10-6/℃) ,说明少量ZrO2的加入可以改善BLT陶瓷的品质因数和频率温度系数,略降低介电常数. SEM分析表明,少量ZrO2的加入没有改变烧结体的微观形貌,改性前后烧结体内部均为典型的柱状TB固溶体形貌.     

CaTiO3∶Zn溶胶-凝胶法制备、结构及介电性能

采用溶胶-凝胶法制备了CaTiO3∶Zn纳米粒子,透射电镜图显示平均粒径为25 nm。Zn的掺杂位置对于陶瓷相组成和烧结特性有很大影响。Ca1-xZnxTiO3和CaTiO3+zZnO样品的Zn以Zn2TiO4相形式存在;而CaZnyTi1-yO3-δ(y=0.01)样品中的Zn进入Ti位形成固溶体,无明显的降温效果,当Zn量增至0.05和0.1时,出现ZnO相。ZnO和Zn2TiO4第二相的存在均能明显促进陶瓷烧结。CaTiO3∶Zn超细粉体可在较低温度下致密烧结(≤1 250℃)。1 250℃烧结的CaZnyTi1-yO3-δ(y=0.01)陶瓷具有较好的介电性能:介电常数ε=157,品质因数Q×f=6 819 GHz,谐振频率温度系数τf=7.51×10-4℃-1。     

低温烧结NaBi(WO4)2陶瓷的介电性能

采用固相合成法制备了NaBi(WO₄)₂(NBW)陶瓷,研究了NBW陶瓷的相结构、形貌、烧结特性和微波介电性能。NBW陶瓷在625～800℃烧结1～4 h能够致密化。X射线衍射表明在625～800℃烧结2 h的NBW陶瓷均为四方晶系白钨矿结构的单相陶瓷。随着烧结温度的提高,NBW陶瓷的介电常数、品质因数(Qf值)先增加后降低,谐振频率温度系数逐渐降低。经650℃烧结2 h获得的NBW陶瓷的介电常数为14.36,Qf值为16 503 GHz,谐振频率温度系数为-1.055×10^-5℃^-1。NBW陶瓷与银共烧反应生成Ag₂W₂O₇相,而与Au、Al共烧具备化学兼容性。     

Ce0.8Sm0.2O1.9的尿素燃烧法合成与性能

采用以尿素为燃料的燃烧合成法制备Ce0.8Sm0.2O1.9(SDC)氧离子导体材料, 对燃烧合成粉体的物相和显微形态进行了表征, 并研究了燃烧法合成SDC的烧结性能以及烧结体的导电性能. 研究结果表明, 采用尿素燃烧法合成SDC具有简便高效和合成粉体烧结活性高的优点. 经过燃烧过程后即可得到立方萤石结构的纯相SDC粉体, 合成粉体的分散性良好, 为50~150 nm的球形颗粒, 具有高的烧结活性, 在1250 ℃的烧结温度下, 陶瓷样品的相对密度可达到95.1%. 在600和800 ℃的测试温度下, 烧结温度为1250 ℃的陶瓷样品的电导率分别达到5.4×10-2和1.0×10-1 Ω-1·cm-1.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Cu-MOF催化过氧化氢应用于多巴胺的检测

本文利用一种具有H_2O_2催化活性的Cu-MOF[Cu_3(BTC)_2(H_2O)_3,简称HKUST-1],构建了以邻苯二胺(OPD)为颜色指示分子的比色传感体系,实现了对H_2O_2和多巴胺(DA)的快速灵敏检测。HKUST-1起到催化H_2O_2氧化OPD的作用,反应体系能够呈现出显著的颜色变化。在优化条件下,415nm处的吸收峰强度与H_2O_2浓度呈双线性关系,线性范围分别为10~50 mmol/L和50~100 mmol/L,相对标准偏差分别为0.9947和0.9995,最低检出限为1.29mmol/L。由于DA能抑制H_2O_2氧化OPD,因此比色传感体系还可以用于快速检测DA,线性范围分别为0.25~5μmol/L和2.5~25μmol/L,相对标准偏差分别为0.9783和0.9705,最低检出限为0.262μmol/L。该项工作拓展了Cu-MOFs材料在生物分子催化和生物传感方面的应用。     

Magnetic diphase nanostructure of ZnFe2O4/γ-Fe2O3

Magnetic diphase nanostructures of ZnFe₂O₄/γ-Fe₂O₃ were synthesized by a solvothermal method. The formation reactions were optimized by tuning the initial molar ratios of Fe/Zn. All samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, and Raman spectra. It is found that when the initial molar ratio of Fe/Zn is larger than 2, a diphase magnetic nanostructure of ZnFe₂O₄/γ-Fe₂O₃ was formed, in which the presence of ZnFe₂O₄ enhanced the thermal stability of γ-Fe₂O₃. Further increasing the initial molar ratio of Fe/Zn larger than 6 destabilized the diphase nanostructure and yielded traces of secondary phase α-Fe₂O₃. The grain surfaces of diphase nanostructure exhibited a spin-glass-like structure. At room temperature, all diphase nanostructures are superparamagnetic with saturation magnetization being increased with γ-Fe₂O₃ content.     

MgAl2O4尖晶石对锂离子电池正极材料LiMn2O4的循环性能影响研究

MgAl₂O₄ spinel doping into cathode materials LiMn₂O₄ was used to improve the cyclic performance of the cathode. X-ray analysis results showed, when MgAl₂O₄ precursors were mixed with LiMn₂O₄ and sintered at 770 ℃ for 12 hour, MgAl₂O₄-LiMn₂O₄ mulriple spinel with the same physical characteristics as pure LiMn₂O₄ were synthesized. The electro-chemical performance testing showed, comparing with pure LiMn₂O₄, the first charge-discharge capacity of doping materials somewhat reduced, but the cyclic performance improved. The mechanism for doping material was also discussed.     

The crystal structure determinations and refinements of K2S2O7, KNaS2O7 and Na2S2O7 from X-ray powder and single crystal diffraction data

The crystal structures of K₂S₂O₇, KNaS₂O₇ and Na₂S₂O₇ have been solved and/or refined from X-ray synchrotron powder diffraction data and conventional single-crystal data. K₂S₂O₇: From powder diffraction data, monoclinic C2/c, Z=4, a=12.3653(2), b=7.3122(1), , β=93.0792(7)°, R_Bragg=0.096. KNaS₂O₇: From powder diffraction data; triclinic , Z=2, a=5.90476(9), b=7.2008(1), , α=101.7074(9), β=90.6960(7), γ=94.2403(9)°, R_Bragg=0.075. Na₂S₂O₇: From single-crystal data; triclinic , Z=2, a=6.7702(9), b=6.7975(10), , α=116.779(2), β=96.089(3), γ=84.000(3)°, R_F=0.033. The disulphate anions are essentially eclipsed. All three structures can be described as dichromate-like, where the alkali cations coordinate oxygens of the isolated disulphate groups in three-dimensional networks. The K-O and Na-O coordinations were determined from electron density topology and coordination geometry. The three structures have a cation-disulphate chain in common. In K₂S₂O₇ and Na₂S₂O₇ the neighbouring chains are antiparallel, while in KNaS₂O₇ the chains are parallel. The differences between the K₂S₂O₇ and Na₂S₂O₇ structures, with double-, respectively single-sided chain connections and straight, respectively, corrugated structural layers can be understood in terms of the differences in size and coordinating ability of the cations.     

Energetics of copper diphosphates – Cu2P2O7 and Cu3(P2O6OH)2

Differential scanning calorimetry and high temperature oxide melt solution calorimetry are used to study enthalpy of phase transition and enthalpies of formation of Cu₂P₂O₇ and Cu₃(P₂O₆OH)₂. α-Cu₂P₂O₇ is reversibly transformed to β-Cu₂P₂O₇ at 338–363 K with an enthalpy of phase transition of 0.15 ± 0.03 kJ mol⁻¹. Enthalpies of formation from oxides of α-Cu₂P₂O₇ and Cu₃(P₂O₆OH)₂ are −279.0 ± 1.4 kJ mol⁻¹ and −538.8 ± 2.7 kJ mol⁻¹, and their standard enthalpies of formation (enthalpy of formation from elements) are −2096.1 ± 4.3 kJ mol⁻¹ and −4302.7 ± 6.7 kJ mol⁻¹, respectively. The presence of hydrogen in diphosphate groups changes the geometry of Cu(II) and decreases acid–base interaction between oxide components in Cu₃(P₂O₆OH)₂, thus decreasing its thermodynamic stability.     

High-pressure transitions in MgAl2O4 and a new high-pressure phase of Mg2Al2O5

Phase transitions in MgAl₂O₄ were examined at 21-27 GPa and 1400-2500 °C using a multianvil apparatus. A mixture of MgO and Al₂O₃ corundum that are high-pressure dissociation products of MgAl₂O₄ spinel combines into calcium-ferrite type MgAl₂O₄ at 26-27 GPa and 1400-2000 °C. At temperature above 2000 °C at pressure below 25.5 GPa, a mixture of Al₂O₃ corundum and a new phase with Mg₂Al₂O₅ composition is stable. The transition boundary between the two fields has a strongly negative pressure-temperature slope. Structure analysis and Rietveld refinement on the basis of the powder X-ray diffraction profile of the Mg₂Al₂O₅ phase indicated that the phase represented a new structure type with orthorhombic symmetry (Pbam), and the lattice parameters were determined as a=9.3710(6) Å, b=12.1952(6) Å, c=2.7916(2) Å, V=319.03(3) Å³, Z=4. The structure consists of edge-sharing and corner-sharing (Mg, Al)O₆ octahedra, and contains chains of edge-sharing octahedra running along the c-axis. A part of Mg atoms are accommodated in six-coordinated trigonal prism sites in tunnels surrounded by the chains of edge-sharing (Mg, Al)O₆ octahedra. The structure is related with that of ludwigite (Mg, Fe²⁺)₂(Fe³⁺, Al)(BO₃)O₂. The molar volume of the Mg₂Al₂O₅ phase is smaller by 0.18% than sum of molar volumes of 2MgO and Al₂O₃ corundum. High-pressure dissociation to the mixture of corundum-type phase and the phase with ludwigite-related structure has been found only in MgAl₂O₄ among various A²⁺B³⁺₂O₄ compounds.     

CeO2改性Ag-V2O5/TiO2催化剂的甲基吡啶氧化脱甲基性能

以锐钛矿TiO_2为载体,考察了CeO_2改性对Ag-CeO_2-V_2O_5/TiO_2催化3-甲基吡啶氧化脱甲基性能的影响,并优化了催化剂组成与制备条件.结果表明:Ce掺杂改性不仅能够与V物种作用形成Ce VO_4,而且促进V_2O_5分散,改善活性组分的氧化还原性能,从而提高3-甲基吡啶脱甲基转化率与选择性,改善Ag-V_2O_5/TiO_2催化性能.适宜的催化剂组成为V_2O_5负载量15%,Ce/V的摩尔比0.33,Ag质量分数1.0%.过高的焙烧温度将导致TiO_2载体向金红石型转变,Ag-CeO_2-V_2O_5/TiO_2适宜制备条件为450℃焙烧4 h.     

La2O3对Ni/γ-Al2O3甲烷化催化剂的助催化作用

我国将稀土作为助剂引入镍基甲烷化催化剂,大大提高了催化剂的活性和热稳定性,并已投入工业应用［1－3］．稀土对不同镍催化剂反应性能及其作用机理的研究已有一些报导［3－7］．谢有畅等观察到镍负载在经单层La2O3改性的γ－Al2O3表面,其晶粒要比没有La2O3时小得多．Rotgerink等认为添加La后反应速率的增加不只是由于几何效应,而是La对甲烷化本身有促进作用,单位镍表面的活性是随La含量不同而改变的,活性增加的同时表观活化能也增加［5］．作为助剂的La2O3在氢还原和反应过程中的变化及其作用的研究和讨论较少,目前一般认为添…