B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

(ZrO2)0.86(Sm2O3)0.14纳米粉体的水热法合成及其烧结体的电性能

以湿化学法制得Zr(OH)₄和Sm(OH)₃的共沉淀为前驱体, 在碱性介质中用水热法合成了(ZrO₂)_0.86(Sm₂O₃)_0.14及(ZrO₂)_0.88(Sm₂O₃)_0.12纳米粉体. 将纳米粉体在较低温度(1450 ℃)下烧结制得了致密的固体电解质陶瓷样品, 比通常高温固相反应法采用的烧结温度(＞1600 ℃)降低了150 ℃以上. XRD测定结果表明, (ZrO₂)_0.86(Sm₂O₃)_0.14纳米粉体及其烧结体均为立方相, 但(ZrO₂)_0.88(Sm₂O₃)_0.12纳米粉体为立方相, 它的烧结体为立方相和单斜相的混合相. 用交流阻抗谱法、氧浓差电池法及氧泵(氧的电化学透过)法研究了(ZrO₂)_0.86(Sm₂O₃)_0.14陶瓷样品在600～1000 ℃下的离子导电特性. 结果表明, 该陶瓷样品在600～1000 ℃下氧离子迁移数为1, 氧离子电导率的最大值为3.2×10^－2 S•cm^－1, 是一个优良的氧离子导体; 它的氧泵性能明显地优于YSZ.     

Nd2O3添加量对BaTiO3陶瓷介电性能的影响

BaTiO₃ ceramics doped with Nd₂O₃(the additive content was respectively 0.001,0.002,0.003,0.005,0.01,0.03mol)were prepared by Sol-Gel method. Effects of Nd₂O₃ contents on the dielectric constant (ε), the dielectric loss (tanδ) ,the Curie-temperature (T_C) and the resistivity (ρ) of BaTiO₃ ceramic were studied. When Nd₂O₃ content was 0.001mol and 0.002mol, the dielectric constant was increased obviously, but the dielectric loss was also increased. When Nd₂O₃ content was 0.003mol, the dielectric constant was increased, and the dielectric loss was decreased, which was suitable for application in condenser. The resistivity was decreased obviously with the increasing of Nd₂O₃ contents, the resistivity was the smallest when Nd₂O₃ content was 0.001mol. The Curie-temperature was also decreased with the increasing of Nd₂O₃ contents.     

在CeO2-ZrO2中加入La2O3对改善单Pd三效催化剂性能的作用

浸渍法制备了CeO₂-ZrO₂-La₂O₃复合氧化物，用XRD、热分析（TG-DTA，DSC）、BET表面积、H₂-TPR等对合成样品进行表征，研究了La₂O₃的加入对CeO₂-ZrO₂和单钯Pd/CeO₂-ZrO₂/γ-Al₂O₃/蜂窝陶瓷催化剂性能和热稳定性的影响。结果表明，在CeO₂-ZrO₂-La₂O₃中，La的存在能促进CeO₂-ZrO₂固溶体的还原，提高贮氧能力；在Pd/CeO₂-ZrO₂/γ-Al₂O₃中加入La有利于提高催化剂的耐热稳定性，阻止γ-Al₂O₃在高温下的晶相转变，进一步稳定Al₂O₃的结构，保持其高的表面积。在贵金属Pd的负载量为1 g·L^-1的条件下，测定了Pd/CeO₂-ZrO₂-La₂O₃/γ-Al₂O₃/蜂窝陶瓷催化剂对CO、C₃H₈和NOx的三效催化净化活性。结果表明，在Pd/CeO₂-ZrO₂/Al₂O₃/蜂窝陶瓷催化剂中加入La₂O₃后，能明显地改善催化剂的低温活性和三效催化性能，经1 000 ℃老化10 h后，CO、C₃H₈和NO_x净化的起燃温度（T₅₀）分别为330 ℃、350 ℃和380 ℃。     

P2O5对Li2O-SiO2-Al2O3-K2O-ZnO体系微晶玻璃析晶性能的影响

采用差热分析、X射线衍射及扫描电镜分析手段研究了P₂O₅对Li₂O-SiO₂-Al₂O₃-K₂O-ZnO体系牙科微晶玻璃析晶性能的影响, 并确定了P₂O₅的最适含量. 结果发现P₂O₅是该玻璃体系的有效成核剂, 未添加P₂O₅的玻璃体系成核密度低, 热处理后不能形成微晶体, 且主晶相为硅酸锂; 添加P₂O₅使玻璃在热处理后形成以二硅酸锂为主晶相的微晶玻璃. 该玻璃体系中添加4.5 wt%的P₂O₅可以得到较高体积含量和理想显微结构的牙科二硅酸锂微晶玻璃. P₂O₅含量为6 wt%的基质玻璃发生乳浊, 呈不透明的乳白色.     

Mn2O3纳米结构的简易合成与电化学性质

用简易的室温或水热方法制备出不同形貌的MnCO₃微结构。经600 ℃热处理后,室温制备MnCO₃转变成Mn₂O₃胶体片,而水热制备MnCO₃样品则形成多孔Mn₂O₃纳米结构。然而,室温制备MnCO₃经120 ℃热处理后形成Mn₂O₃晶相。制备样品经过XRD和SEM表征表明,热处理MnCO₃前驱物形成Mn₂O₃过程导致产物形貌与结构变化。其形成机理又通过TEM和FTIR进一步研究。Mn₂O₃纳米结构的电容性质通过循环伏安法表征,结果表明Mn₂O₃形貌与结构对其电容有重要影响。     

共沉淀法合成Yb3+∶Y2O3纳米粉及透明陶瓷的性能

以Y₂O₃为基质材料,掺杂不同含量的Yb³⁺,采用共沉淀法制备出性能良好的Yb³⁺∶Y₂O₃纳米粉,将粉体在1 700 ℃和真空度为1×10^-3 Pa下烧结5 h得到Yb³⁺∶Y₂O₃透明陶瓷。用XRD、TEM、UV-Vis、FL分别对样品的结构、形貌和发光性能进行了研究。结果表明：Yb³⁺完全固溶于Y₂O₃的立方晶格中,Yb³⁺∶Y₂O₃粉体大小均匀,近似球形,尺寸约40～60 nm。Yb³⁺∶Y₂O₃透明陶瓷相对密度为99.7%,在波长600～800 nm范围内其透光率达到80%。Yb³⁺∶Y₂O₃透明陶瓷在950 nm处吸收线宽达到26 nm,在1 031 nm和1 076 nm处的发射线宽分别为13 nm和17 nm。     

Au/Al2O3纳米复合薄膜的制备和表征

用溶胶-凝胶法制备了Au/Al₂O₃纳米复合薄膜。利用X-射线衍射、X-射线光电子能谱、原子力显微镜以及紫外-可见光谱对薄膜的微观结构、表面形貌及光学性能进行了表征,研究表明:Au/Al₂O₃纳米复合薄膜是由纳米微晶组成的颗粒膜, 复合薄膜均匀、致密、无裂纹,Au以纳米晶核形式镶嵌于Al₂O₃基体中,纳米Au晶核的粒径为23～26nm;复合薄膜在可见光区有较强的吸收,吸收峰位置与烧结温度有关,吸收强度随烧结温度和金添加量增大而增大。     

CA配合法制备β-Al2O3固体电解质

采用柠檬酸(CA)做还原剂,硝酸盐做氧化剂,利用溶胶凝胶-低温燃烧合成工艺制备了β-Al₂O₃前驱粉料,并利用热分析(TG/DSC)、红外吸收光谱分析(FTIR)、X射线衍射分析(XRD)、扫描电镜(SEM)和交流阻抗谱(EIS)等测试技术对β-Al₂O₃的合成工艺进行了详细的研究。结果表明：该法合成β-Al₂O₃前驱粉料的温度为1 150 ℃,比固相反应法低了150 ℃,平均粒径约为38 nm,具有较好的成型和烧结性能。将素坯在1 630 ℃保温烧结,得到的烧结体相对密度为96%以上,350 ℃时的电导率为0.061 S·cm^-1。     

整体式Co3O4/YSZ- -Al2O3＋CYZ催化剂上的甲烷催化燃烧

用质量比为3∶2的YSZ-γ-Al₂O₃和CeO₂-Y₂O₃-ZrO₂的混合物(以YSZA＋CYZ表示)作载体, 制备了不同Co₃O₄含量的整体式甲烷燃烧催化剂, 同时制备了分别以YSZA和CYZ为载体的催化剂作为对比, 研究了它们老化前后的反应性能, 并用BET, XPS, XRD, TPR等研究了催化剂的比表面、表面状态、晶相结构和还原性能. 结果表明, YSZ- -Al₂O₃和CeO₂-Y₂O₃-ZrO₂混合载体能有效地抑制CoAl₂O₄的生成, 并能充分发挥各自的优点, 因此负载一定量的钴后表现出很高的甲烷催化燃烧活性和抗老化性, 尤其是含8 wt% Co₃O₄的样品性能最佳, 有望成为实用的甲烷燃烧催化剂之一.     

La2O3对Ni/γ-Al2O3甲烷化催化剂的助催化作用

我国将稀土作为助剂引入镍基甲烷化催化剂,大大提高了催化剂的活性和热稳定性,并已投入工业应用［1－3］．稀土对不同镍催化剂反应性能及其作用机理的研究已有一些报导［3－7］．谢有畅等观察到镍负载在经单层La2O3改性的γ－Al2O3表面,其晶粒要比没有La2O3时小得多．Rotgerink等认为添加La后反应速率的增加不只是由于几何效应,而是La对甲烷化本身有促进作用,单位镍表面的活性是随La含量不同而改变的,活性增加的同时表观活化能也增加［5］．作为助剂的La2O3在氢还原和反应过程中的变化及其作用的研究和讨论较少,目前一般认为添…     

The Al2O3-Fe2O3 Mixed Oxidic System, I. Preparation and Characterization

A series of Al₂O₃-Fe₂O₃ mixed oxidic solids with composition ranging from 0 to 100% of Fe₂O₃ were prepared and examined for structural characteristics. XRD diagrams showed the presence of α-Al₂O₃ and hematite phases. The analysis of M?ssbauer spectra revealed the existence of two iron containing phases. The specific surface area of the mixture decreases by the addition of iron and depends on the crystal phases of the mixture. This revised version was published online in June 2006 with corrections to the Cover Date.     

Fe2O3/Al2O3二元气凝胶合成高质量单壁纳米碳管

通过溶胶和超临界干燥方法制得了Fe₂O₃/Al₂O₃二元气凝胶，其比表面积和孔隙体积分别为246 m²·g^-1和1.89 cm³·g^-1，并具有较宽的孔径分布。以Fe₂O₃/Al₂O₃二元气凝胶作催化剂，通过甲烷催化裂解成功地合成了高质量的单壁纳米碳管。利用FESEM、TEM和HRTEM、Raman光谱等分析手段研究了反应温度对单壁纳米碳管生长的影响。结果表明在900 ℃时合成单壁纳米碳管的质量较高，并且合成的炭产物为毡状，该炭产物主要为高质量的单壁纳米碳管。     

BaO-Al2O3-B2O3系密封玻璃的结构与性质

The BaO-Al₂O₃-B₂O₃ glasses manufactured for solid oxide fuel cell(SOFC) sealing were studied. The effect of different n_BaO/n_B2O3 on crystal, thermal properties, density and infrared spectra of this system has been discussed. The results show that the trends of crystallization, glass transformation temperature, dilatometric softening temperature and density increase with n_BaO/n_B2O3 values. But a typical property deviation occurs when n_BaO/n_B2O3 is 0.875, and its coefficient of thermal expansion has the maximum at this point. The changes of properties can attribute to the conversion of boron from tetrahedral coordination to trigonal, breakage of the local glass network and interaction between the network modifiers. These can be proved by infrared spectra of glasses. Thermal properties of some studied samples are suitable for the sealing of SOFC using Sm doped ceria electrolyte and operating at 400～600 ℃.     

The Al2O3-Fe2O3 Mixed Oxidic System, II. Catalytic Decomposition of N2O

N₂O decomposition was examined over a series of Al₂O₃-Fe₂O₃ mixed oxidic solids with composition ranging from 0 to 100% of Fe₂O₃. The catalytic activity of the solids runs parallel to the number of atoms of iron in the Al_2−x Fe_xO₃ solid solution phase. Two compensation effects are present. The first corresponds to catalysts rich in alumina, and the second one to catalysts rich in hematite. This revised version was published online in June 2006 with corrections to the Cover Date.     

Magnetic diphase nanostructure of ZnFe2O4/γ-Fe2O3

Magnetic diphase nanostructures of ZnFe₂O₄/γ-Fe₂O₃ were synthesized by a solvothermal method. The formation reactions were optimized by tuning the initial molar ratios of Fe/Zn. All samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, and Raman spectra. It is found that when the initial molar ratio of Fe/Zn is larger than 2, a diphase magnetic nanostructure of ZnFe₂O₄/γ-Fe₂O₃ was formed, in which the presence of ZnFe₂O₄ enhanced the thermal stability of γ-Fe₂O₃. Further increasing the initial molar ratio of Fe/Zn larger than 6 destabilized the diphase nanostructure and yielded traces of secondary phase α-Fe₂O₃. The grain surfaces of diphase nanostructure exhibited a spin-glass-like structure. At room temperature, all diphase nanostructures are superparamagnetic with saturation magnetization being increased with γ-Fe₂O₃ content.     

The Ternary System Li2O-Al2O3-B2O3: Compounds and Phase Relations

The ternary system Li₂O-Al₂O₃-B₂O₃ is reinvestigated with solid-state reaction and X-ray powder diffraction technique to clarify some long-standing uncertainties. The phase relations are constructed based on the phase identifications of 51 ternary samples. Six ternary compounds, Li₂AlB₅O₁₀, LiAlB₂O₅, Li₃AlB₂O₆, Li₂AlBO₄, LiAl₇B₄O₁₇ and a compound with a composition close to 0.66Li₂O·0.06Al₂O₃·0.28B₂O₃, are observed or confirmed in this system, and the thermal stability of these ternary compounds is also discussed on the basis of DTA experimental results.     

一维纳米Co_3O_4,Ag/Co_3O_4及CuO/Co_3O_4的合成与电催化性能(英文)

采用水热合成法制备了Co3O4及复合Ag/Co3O4、CuO/Co3O4一维纳米产品。用XRD,FE-SEM和TEM手段对产品进行了表征。采用循环伏安法研究了合成产品修饰的玻碳电极在碱性溶液中对对硝基苯酚的电催化还原性能。与裸玻碳电极相比,1mmol·L-1的对硝基苯酚在用Co3O4、特别是CuO/Co3O4修饰的玻碳电极上还原的峰电流明显增大,用Ag/Co3O4(Ag/Co原子比分别为1∶5和2∶5)修饰的玻碳电极催化还原对硝基苯酚时,尽管还原峰电流增大不是太大,但其峰电位明显降低(分别降低0.265和0.371V)。     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.