邻甲基苯甲醛的“槽内式”间接电合成

邻甲基苯甲醛的“槽内式”间接电合成;邻甲基苯甲醛; 氧电还原; 氧还电对V5+/V4+; 邻二甲苯; 电解     

基于径向基神经网络和遗传算法的槽内式选择性超声电合成甲基苯甲醛

以混合二甲苯为原料, Mn(Ⅲ)为氧化剂, 硫酸溶液为电解质, 采用槽内式超声电合成甲基苯甲醛. 探讨了选择性电合成甲基苯甲醛的可能性, 通过径向基(RBF)神经网络和遗传算法(GA)对选择性电合成甲基苯甲醛3种异构体的比例、 电流效率与混合二甲苯的用量、 硫酸浓度和电流强度的关系建立预测模型, 并运用GA确定模型中RBF神经网络的目标均方误差(Goal)和径向基函数的分布(Spread). 然后根据预测模型, 使用GA对电合成条件进行优化, 分别获得了电合成产物中对位甲基苯甲醛占优、 邻位和对位甲基苯甲醛占优以及电流效率最高时的电合成条件. 当采用上述条件进行实验时, 模型给出的预测结果分别为: 对位甲基苯甲醛占优的质量分数可达90.01%, 邻位和对位甲基苯甲醛占优的质量分数为80.38%, 电流效率达到最高时的邻位、 间位和对位甲基苯甲醛的质量分数分别为16.80%, 8.43%和74.77%; 而与之相对应的实际实验结果分别为90.10%和79.91%, 以及17.20%, 8.49%和74.31%, 二者之间的最大相对误差小于±2.24%, 表明所建立模型的预测值与实测值基本吻合.     

电催化氧化制备苯甲醛的研究

在超声波槽中电生成纳米金属氧化物,继而以MnO2/Mn2 或金属氧化物氧化还原电对作为媒介,电催化氧化合成苯甲醛.实验表明,电流效率和苯甲醛的产率在超声的参与下有明显的提高,优化了超声电解的条件.在较高温度下反应时,有利于提高生成苯甲醛的电流效率.反应选择性较高,苯甲醛产率可达88.9%.     

对溴苯甲醛的间接电化学合成

以硫酸为介质,利用电解MnSO4生成Mn3+将对溴甲苯氧化为对溴苯甲醛;通过设计有机氧化正交实验L9(33),对电解氧化条件进行了优化.优化电解条件为:硫酸浓度6.5 mol/L、对溴甲苯与Mn3+摩尔比1∶4、电解时间6 h、合成时间3 h、温度65℃;相应的电流效率可达75.36%,对溴苯甲醛的产率可达75.47%.所采用的间接电化学合成工艺路线简单,使用后的媒质可以再生循环使用,符合绿色生产的要求.     

间接电合成甲基苯甲醛产物中3种异构体的同时测定

将迭代算法、PLS与紫外吸收光谱法相结合,建立了同时测定二甲苯间接电合成甲基苯甲醛混合6组分中3种甲基苯甲醛含量的新方法。该方法将PLS镶嵌在迭代算法内部,通过多次迭代计算逐步逼近样品真值,提高了光谱的识别能力。将该方法用于4组模拟样本的测定,邻、间、对甲基苯甲醛的平均回收率分别为101%、100%和101%,预测均方差(RMSEP)分别为0.214、0.148和0.057。而应用于5批实际电合成产物中3种甲基苯甲醛同分异构体的同时测定,邻、间、对甲基苯甲醛的平均回收率分别为106%、92%和100%,相对偏差≤±19.7%,与高效液相色谱法测定结果基本吻合。     

电合成间苯氧基苯甲酸

以Nafion417作隔膜,Pb-PbO2作阳极,Pb作阴极,电解氧化Cr(Ⅲ)为Cr(Ⅵ),然后以Cr(Ⅵ)为氧化媒质,氧化间甲基二苯醚为间苯氧基苯甲酸.研究了在Nafion417隔膜槽中影响Cr(Ⅲ)电氧化的因素,并进一步探究优化电合成间苯氧基苯甲酸的工艺条件.     

间甲基苯胺和邻甲基苯胺恒电位电化学聚合行为的比较研究

在0.5 mol·L-1H2SO4水溶液中,以ITO导电玻璃为工作电极,用原位紫外-可见光谱进行跟踪恒电位电聚合间甲基苯胺和邻甲基苯胺.结果表明邻甲基苯胺的电化学聚合要比间甲基苯胺快.在0.9 V(vs.饱和Ag/AgCl)恒电位电解时的电流-时间响应曲线表明聚间甲基苯胺和聚邻甲基苯胺在导电玻璃上的沉积方式是不同的,在电解初期两者均可能以时间累积成核方式沉积,但随着电解的进行,邻甲基苯胺电化学聚合发生支链化,而间甲基苯胺的电化学聚合反应却变慢.扫描电镜图表明聚邻甲基苯胺具有多孔颗粒状的表面形貌,而聚间甲基苯胺却具有致密的表面形貌.量子化学从头计算(6-31**/B3LYP)表明,半氧化态的间甲基苯胺四聚体发生了明显的卷曲而与此对应的邻甲基苯胺四聚体却没有明显的卷曲;这说明尽管聚邻甲基苯胺和聚间甲基苯胺在化学结构上是类似的,但它们的空间结构可能存在明显的不同,导致其聚合和在电极沉积的方式可能产生较大的差别.     

取代芳烃电解氧化产物的GC-MS分析(Ⅱ)

采用GC-MS方法,分析了3种取代芳烃直接电解氧化的产物;从甲苯电解氧化产物中鉴定出7种主要成分,从对甲基苯甲醚电解氧化产物中鉴定出6种主要成分,从对叔丁基甲苯电解氧化产物中鉴定出6种主要成分;根据成分鉴定和含量测定结果,解释了以获取目标产物苯甲醛、对甲氧基苯甲醛和对叔丁基苯甲醛为目的的电解氧化反应要求。     

在线超声成对电合成苯甲醛和丁二酸

将间接电合成苯甲醛与电还原马来酸制备丁二酸的过程有机结合, 构建了一个新的成对电解体系, 即在隔膜电解槽中, 以纯Pb为阴极, PbO₂/Pb为阳极, 硫酸溶液为介质, 在施加超声波的条件下, 阳极氧化Ce³⁺为Ce⁴⁺, 阴极还原马来酸生成丁二酸; 同时, 在槽外采用Ce⁴⁺氧化甲苯生成苯甲醛. 实验结果表明, 阴极和阳极电解的平均电流效率分别为92.71%和87.81%, 总的电流效率高达180.52%; 且Ce⁴⁺槽外氧化甲苯为苯甲醛的收率为95.78%, 马来酸电还原为丁二酸的转化率为92.09%; 电解的槽电压与单一电解氧化Ce³⁺相比降低了0.25 V.     

改进的固相萃取-高效液相色谱法测定土壤中15种醛酮类化合物北大核心CSCD

建立了改进的固相萃取-高效液相色谱法测定土壤中甲醛、乙醛、丙烯醛、丙酮、丙醛、丁烯醛、丁醛、苯甲醛、异戊醛、正戊醛、邻-甲基苯甲醛、间-甲基苯甲醛、对-甲基苯甲醛、正己醛和2,5-二甲基苯甲醛等15种醛酮类化合物的分析方法。利用乙腈对土壤进行超声提取,样品提取液与2,4-二硝基苯肼(2,4-DNPH)进行衍生化反应,生成稳定的腙类化合物;随后利用装有亲水亲脂平衡的N-乙烯基吡咯烷酮/二乙烯基苯共聚物填料的固相萃取小柱(Welchrom^(■)BRP)对衍生后的溶液进行净化;采用Ultimate^(■)XB-C_(18)色谱柱(250 mm×4.6 mm,5μm)进行分离,以乙腈-水(65∶35,v/v)为流动相进行等度洗脱,于波长360 nm处进行检测,利用外标法对土壤中15种醛酮类化合物进行定量。该方法改进了环境标准HJ 997-2018《土壤和沉积物醛、酮类化合物的测定高效液相色谱法》中试样的处理方法,优化后得到土壤的最佳提取条件,即:提取溶剂为乙腈,提取温度为30℃,提取时间为10 min。结果表明:采用BRP小柱的净化效果明显优于普通硅胶基质C_(18)小柱,15种醛酮类化合物在各自的范围内线性关系良好,线性相关系数均在0.996以上;平均加标回收率为84.6%~115.9%,相对标准偏差(RSD)为0.2%~5.1%;检出限为0.02~0.06 mg/L。该方法简便,灵敏度高,准确性好,适用于HJ 997-2018中规定的土壤和沉积物中15种醛酮类化合物的准确定量分析,为研究土壤中醛酮类化合物的残留状况和环境行为提供了可靠的技术支持。     

Relativistic multireference calculation of photodissociation of o-, m-, and p-bromofluorobenzene

Quantum chemical calculations with relativistic effects were performed on the photodissociation of o-, m-, and p-bromofluorobenzene (o-, m-, and p-BrFPh) at 266 nm. The method of multistate second-order multiconfigurational perturbation theory in conjunction with spin-orbit interaction through complete active space state interaction was employed to calculate the potential energy curves for the ground and low-lying excited states of o-, m-, and p-BrFPh along their photodissociation reaction coordinates. The dissociation mechanisms with products of Br((2)P(3∕2)) and Br(?)((2)P(1∕2)) states were clarified with the computed potential energy curves and the surface crossings. The current calculations augmented previous theoretical investigations by including relativistic effects and resolved some differences of experimental assignment regarding the dissociation channels of o-, m-, and p-BrFPh.     

羧基苯偶氮基杯[8]芳烃衍生物的合成及表征

以邻、间或对氨基苯甲酸和杯[8]芳烃为原料，经重氮化一偶联反应合成了新型有色邻、间或对羰基苯偶氮基杯[8]芳烃，产物的结构经元素分析，IR，UV－Vis和1H NMR表征，并研究了它们的生色原理和光谱性能，实验结果表明它们是一类新型指示剂和具有新型配位空腔的主体分子。     

Excited state hydrogen transfer in fluorophenol.ammonia clusters studied by two-color REMPI spectroscopy

Two-color (1 + 1') REMPI mass spectra of o-, m- and p-fluorophenol.ammonia (1 ration) clusters were measured with a long delay time between excitation and ionization lasers. The appearance of NH(4)(NH(3))(n-1)(+) with 100 ns delay after exciting the S(1) state is a strong indication of generation of long-lived species via S(1). In analogy with the phenol.ammonia clusters, we conclude that an excited state hydrogen transfer reaction occurs in o-, m- and p-fluorophenol.ammonia clusters. The S(1)-S(0) transition of o-, m- and p-fluorophenol.ammonia (1 : 1) clusters were measured by the (1 + 1') REMPI spectra, while larger (1 ration) cluster (n = 2-4) were observed by monitoring the long-lived NH(4)(NH(3))(n-1) clusters action spectra. The vibronic structures of m- and p-fluorophenol.ammonia clusters are assigned based on vibrational calculations in S(0). The o-fluorophenol.ammonia (1 : 1) cluster shows an anharmonic progression that is analyzed by a one-dimensional internal rotational motion of the ammonia molecule. The interaction between the ammonia molecule and the fluorine atom, and its change upon electronic excitation are suggested. The broad action spectra observed for the o-fluorophenol.ammonia (1 : n) cluster (n>== 2) suggest the excited state hydrogen transfer is faster than in m- and p-fluorophenol.ammonia clusters. The different reaction rates between o-, m- and p-fluorophenol.ammonia clusters are found from comparison between the REMPI and action spectra.     

苯二酚异构体的电动毛细管色谱-玻碳微电极柱上安培检测分析方法研究

在玻碳纤维微电极上研究了电解液中β－环糊精（ＣＤ）的浓度对邻、间、对苯二酚的循环伏安特性的影响,从实验结果和分子结构水平方面考察了β－ＣＤ与邻、间、对苯二酚的包结作用。研究结果表明,β－ＣＤ与邻、间、对苯二酚的包结作用强弱顺序为间苯二酚、邻苯二酚、对苯二酚。讨论了电泳缓冲液中ΝΗ４Ｃｌ,ＳＤＳ,β－ＣＤ的浓度及ｐＨ值对邻、间、对苯二酚迁移时间的影响。建立了苯二酚异构体胶束电动毛细管色谱－玻碳微电极柱上安培检测分析方法,方法的回收率在９８％～１０３％之间。     

Separation and determination of some stereoisomers by capillary gel electrophoresis with cyclodextrin incorporated in polyacrylamide gel

Capillary gel electrophoresis (CGE) was successfully applied to the separation of optically active isomers and position isomers by incorporating a suitable cyclodextrin chiral selector in polyacrylamide gel. A commercially available ss-cyclodextrin (ss-CD) was used for enantioselectivity towards o-, m- and p-nitrobenzoic acid, o-, m- and p-hydroxybenzoic acid, o-, m- and p-toluic acid and the optical isomers of dansyl-D,L-leucine and R,S-1,1'-binaphthyl-2,2-dihydrogenphosphate. Especially the effect of organic solvents, such as acetonitrile, methanol, dimethylsulphoxide and others were examined in detail. The resolution varied to some extent with the addition of the organic solvent to the polyacrylamide gel and the running buffer solution. The possible mechanism has also been discussed. In addition, quantitative aspects of the separation of stereoisomers using CGE have been studied, showing that both the resolution and accuracy of the determinations were affected by the ratio of the enantiomers.     

A Fully Non-fused Ring Acceptor with Planar Backbone and Near-IR Absorption for High Performance Polymer Solar Cells

Fused-ring electron acceptors have made significant progress in recent years, while the development of fully non-fused ring acceptors has been unsatisfactory. Here, two fully non-fused ring acceptors, o-4TBC-2F and m-4TBC-2F, were designed and synthesized. By regulating the location of the hexyloxy chains, o-4TBC-2F formed planar backbones, while m-4TBC-2F displayed a twisted backbone. Additionally, the o-4TBC-2F film showed a markedly red-shifted absorption after thermal annealing, which indicated the formation of J-aggregates. For fabrication of organic solar cells (OSCs), PBDB-T was used as a donor and blended with the two acceptors. The o-4TBC-2F-based blend films displayed higher charge mobilities, lower energy loss and a higher power conversion efficiency (PCE). The optimized devices based on o-4TBC-2F gave a PCE of 10.26 %, which was much higher than those based on m-4TBC-2F at 2.63 %, and it is one of the highest reported PCE values for fully non-fused ring electron acceptors.     

Über den Einfluß von Substituenten auf die Ultraviolettabsorption zweier konjugierter Benzolchromophore

Zusammenfassung Es werden die gemessenen Absorptionskurven von o-, m- und p-Amino-, o-, m- und p-Nitro-, sowie o- und p-Cyan-diphenyl in verschiedenen Lösungsmitteln wiedergegeben. Aus der Abhängigkeit der Absorptionsbanden von der Art und Stellung der Substituenten wird auf ihre Zugehörigkeit zum Benzolchromophor geschlossen.     

Effect of hydrogen bonding on the polymerization of N-(o-,m-, and p-methoxyphenyl)- and N-(o-,m-, and p-ethoxyphenyl)-methacrylamides

Summary Study of the rates of polymerization of N-(o-, m-, and p-methoxyphenyl)- and N-(o-, m-, and p-ethoxy-phenyl)methacrylamides showed that the ortho isomers of these compounds, in which there is no association between the molecules, polymerize much more rapidly than their meta and para isomers, the molecules of which are associated through hydrogen bonds.     

Direct observation of intramolecular vibrational energy redistribution under white light excitation. II. Fluorescence spectra of fluorobenzene derivatives by controlled electron impact

The low-resolution (resolution: 0.6 nm) fluorescence spectra of fluorobenzene derivatives, o-, m- and p-fluorotoluene (o-, m- and p-FT) were observed to investigate intramolecular vibrational energy redistribution (IVR) under controlled electron impact. The o- and m-FT spectra mainly consisted of unstructured emission from optically inactive states (bath modes) populated through IVR. The p-FT spectrum consisted of structured emission from optically active states and unstructured emission. The high-resolution (resolution: 0.15 nm) fluorescence spectrum of p-FT was measured to estimate the fraction of the structured emission intensity to the total emission intensity. The IVR rate of p-FT under electron impact excitation was faster than that under laser excitation. The fraction did not depend on the incident energy of electrons from 20 to 200 eV, and thus the IVR acceleration is not attributable to breakdown of the Born approximation.