Study of heterogeneities in steels and determination of soluble and total aluminium and titanium concentration by laser ablation inductively coupled plasma mass spectrometry

A methodology for bulk analysis of Al and Ti and for determination of soluble and total Al and Ti concentration in steel samples by laser ablation inductively coupled plasma mass spectrometry was developed. The spatial distribution (both at surface and within the sample) of the insoluble fraction of Al and Ti was also qualitatively estimated. Certified reference materials (CRMs) SS-451 to 460 (carbon steel) and 064-1 (Nb/Ti interstitial free steel), from BAS, and JK 2D (carbon steel) and JK 37 (highly alloyed steel), from SIMR, were studied. It was demonstrated that the insoluble fraction of Al and Ti is heterogeneously distributed. A series of nine glass samples (fused beads) with fixed Fe content and different Al and Ti contents was prepared by melting appropriate amounts of Fe₂O₃, Al₂O₃ and TiO₂ with a lithium tetraborate–sodium carbonate mixture. Quantitative determinations were performed by using calibration graphs obtained from the synthetic fused beads, with ⁵⁷Fe as internal standard; line scan laser sampling mode was used, focusing the laser beam at the sample surface. The optimized laser operating parameters were: laser pulse energy of 1.5 mJ, pulse repetition rate of 5 Hz, scanning speed of 5 μm s⁻¹ and preablation time of 20 s. The concentrations obtained for bulk analysis of CRM samples corresponded with the certified values within the experimental uncertainty. An acceptable concordance between certified and found values was attained for the determination of soluble and total Al and Ti in CRM 064-1 sample.     

Synthesis of double silylene-bridged binuclear titanium complexes and their use as catalysts for ethylene polymerization

Five new double silylene-bridged binuclear titanium complexes were synthesized by the reaction of RCpTiCl₃ and Li₂[μ,μ-(SiMe₂)₂ (C₅H₃)₂] in toluene. They were all well characterized. These complexes activated with methylaluminoxane (MAO) are highly active catalysts (2.33 × 10⁵ g PE/mol Cat h) for the polymerization of ethylene even at low Al/Ti (Al/Ti = 300). The molecular weight distribution of the polymer indicates broad or bimodal (MWD = 26.76) distribution.     

Supported dichlorobis(3-hydroxi-2-methyl-4-pyrone)Ti(IV) catalysts: Evaluation on ethylene polymerization

Dichlorobis(3-hydroxi-2-methyl-4-pyrone)Ti(IV) complex was grafted on different inorganic supports, namely different kinds of SiO₂, MAO-modified silica, MCM-41, Al₂O₃, ZrO₂ and MgO. The resulting supported catalysts were shown to be active in ethylene polymerization using methylaluminoxane (MAO) as cocatalyst, most of them being even more active that the homogeneous complex. The highest catalyst activities were observed for the Ti complex supported on SiO₂ 948 activated at 450 °C, MCM-41 and Al₂O₃.     

Ti表面修饰纳米TiO2膜电极的电催化活性

用电化学合成法在Ti表面修饰一层纳米TiO₂膜,TEM和XRD测试表明晶型为锐钛矿型,晶粒平均尺寸为25nm.用循环伏安法、循环方波伏安法和电解合成法研究了纳米TiO₂膜电极在硫酸介质中的氧化还原行为以及对硝基苯还原的电催化活性。结果表明,纳米TiO₂膜电极具有异相氧化还原催化行为,膜中的Ti(Ⅳ)/Ti(Ⅲ)作为媒质间接电还原硝基苯为对氨基苯酚,收率和电流效率分别达91.6%和95.2%.     

NaCl-KCl熔盐体系中AlF3氟化Tb4O7电化学制备Al-Tb合金

在NaCl-KCl-Tb₄O₇-AlF₃体系中为了制备Al-Tb合金,首先对熔盐中的上清液和沉淀物进行了分析,X射线衍射（XRD）结果确定了Tb₄O₇能被AlF₃氟化生成TbF₃。采用一系列的电化学方法对NaCl-KCl-AlF₃-Tb₄O₇体系在Mo电极上的电化学行为进行了研究。循环伏安、方波伏安、计时电位和开路计时电位等电化学方法的研究结果表明Tb（III）在预先沉积的Al电极上发生欠电位沉积。在不同条件下进行恒电流电解制备了Al-Tb合金,并对所得合金样品进行XRD和扫描电镜-能量散射谱（SEM-EDS）表征。结果表明在-2.5 A进行恒电流电解得到的Al-Tb合金是由Al和Al₃Tb两相组成。采用电感耦合等离子体-原子发射光谱仪（ICP-AES）对实验所得沉积物的组成进行分析,研究了电解条件对合金组成和电流效率的影响。在电流强度为-1.5 A进行恒电流电解2 h,电流效率可达76.5%。     

TiCl4/Al2Et3Cl3/Y-型分子筛高效乙烯丙烯共聚催化体系的研究

一般高效负载型催化剂多以MgCl_2或Mg系类化合物为载体,SiO_2、Al_2O_3等无机氧化物为载体的催化剂用于丙烯聚合催化活性很低。我们发现,无MgCl_2或Mg系类化合物存在下,以Y型分子筛为载体的Ti系催化剂,在常压下催化效率达10kg P/g Ti·h,并可有效地控制催化剂的载钛量。 1 实验部分 制备催化剂的玻璃反应装置经抽真空,充氮气数次后,依次以一定比例和间隔时间加入HY分子筛、Al_2Et_3Cl_3和TiCl_4,反应在室温、氮气保护下进行。乙烯、丙烯属聚合级产品,聚合过程在严格除水、除氧的条件下进行,各种玻璃仪器均需在100℃以上干燥过夜,用净化后的     

载体对Ni_2P催化剂加氢脱氮反应性能的影响

使用TiO2、Al2O3以及TiO2-Al2O3复合载体考察了载体对磷化镍催化剂活性相和加氢脱氮性能的影响。不同钛铝原子比的TiO2-Al2O3复合载体采用原位-溶胶凝胶法制备,负载的磷化镍催化剂采用等体积浸渍法和H2原位还原法制备。以喹啉为模型化合物在固定床反应器上对催化剂的加氢脱氮性能进行评价,采用XRD、N2吸附、TEM和H2-TPR等技术对催化剂和载体进行了表征。结果表明,制成的复合载体基本保留了最初引入的γ-Al2O3的孔特征,分散在γ-Al2O3表面的TiO2以锐钛矿晶型存在。不同载体对催化剂的H2还原行为有显著影响,所形成的活性物种也不相同。Al2O3中引入TiO2可以减弱P物种和Al2O3之间的相互作用,有利于Ni2P活性相的生成和催化活性的提高。当Ti/Al的原子比为1∶8时,Ni2P/TiO2-Al2O3催化剂比Ni2P/TiO2、Ni2P/Al2O3催化剂具有更高的加氢脱氮活性。     

氯化物熔盐体系中Gd的电化学行为及提取效率的评估

研究了773 K时GdCl₃在LiCl-KCl熔盐体系中在Mo和Al 电极上的电化学行为和热力学特性. 利用开路计时电位曲线得到了Gd(III)/Gd(0)体系在723-873 K温度范围的平衡电极电位和表观电极电位. 结果表明: 平衡电极电位和表观电极电位随着温度的升高而变正. 通过吉布斯自由能变进一步计算得到了GdCl₃在LiCl-KCl熔盐体系中不同温度下的活度系数. 结合稳态极化曲线, 求得去极化值, 并通过热力学计算, 求得773 K时Gd的理论提取效率. 在773 K时, 在LiCl-KCl-GdCl₃体系中, 以Al 为工作电极在-1.5 V左右通过恒电位电解提取Gd, 电解20 h后实际电解提取效率为94.22%. 对电解沉积物进行X射线衍射(XRD)分析, 检测到了Al₃Gd合金相.     

Green synthesis of methyl trifluoropyruvate catalyzed by solid acids

Solid acids – NiSO₄/Al₂O₃, Fe₂(SO₄)₃/Al₂O₃ and TiO₂/SO₄²⁻ – appeared to be effective catalysts for the acid catalyzed synthesis of methyl ester of trifluoropyruvic acid. They are active at 150–180 °C.     

镁助剂改性Pd/Al_2O_3甲烷催化燃烧催化剂:Mg/Al物质的量比对催化剂载体及活性物种形成的影响

本文研究了系列不同含量镁助剂改性的Pd/Al_2O_3催化剂的甲烷催化燃烧反应。研究表明,随着镁添加量的增加,载体由Al_2O_3转变为尖晶石型MgAl_2O_4,进一步增加Mg/Al物质的量比至3∶1时,形成了Mg(Al)O_x固溶体;催化剂中活性相Pd物种以金属Pd,PdO_x或Pd-载体复合氧化物形式存在,各物种的相对含量以及Pd?PdO间的转化能力存在一定的差异。PdO_x物种表现为具有较高的低温活性,而金属Pd和Pd-载体复合氧化物的高温活性较好。当Mg/Al物质的量比为1∶3时,催化剂的Pd?PdO转化能力最强,表现出了最高的甲烷催化燃烧反应活性。     

Ti/RuO2-IrO2-SnO2-Sb2O5阳极在农村饮用水消毒中的应用

采用热分解法制备了一种新型高效析氯阳极Ti/RuO₂-IrO₂-SnO₂-Sb₂O₅,将其应用于农村饮用水消毒频繁停开、低电解液浓度的特殊工况下,并与Ti/RuO₂-SnO₂-Sb₂O₅、Ti/RuO₂-TiO₂、Ti/RuO₂-TiO₂-IrO₂三种析氯阳极进行性能对比。通过SEM、EDS、XRD等方法表征测试阳极表面形貌、元素及组成,考察了氯化钠浓度、电流密度、停开频率对阳极析氯效果和寿命的影响。研究发现,Ti/RuO₂-IrO₂-SnO₂-Sb₂O₅阳极活性强、稳定性高;阳极涂层各组分高度融合为固溶体,结构致密,稳定性强;在15 g·L^-1 NaCl、400 A·m^-2电流密度、20℃条件下,Ti/RuO₂-IrO₂-SnO₂-Sb₂O₅阳极电解的电流效率达到91.55%;频繁停开、强化电解条件下寿命达到231 h,是Ti/RuO₂-TiO₂阳极的77倍,预估在400 A·m^-2电流密度下能够使用20年。     

铝源对Ni/Al2 O3催化剂结构及其CO2-CH4重整性能的影响

以三种不同铝源采用溶液燃烧法制备了系列Ni/Al_2O_3催化剂,通过XRD、H_2-TPR、NH_3-TPD、N_2吸附-脱附、TGDTG和TPH等分析方法对反应前后催化剂进行了表征,研究了铝源对Ni/Al_2O_3催化剂结构、表面性质及其CO_2-CH_4重整性能的影响。结果表明,以Al(NO_3)_3·9H_2O为铝源制备的NiNO-AlNO催化剂比表面积较大,达102 m~2/g;高温还原峰面积大,峰型更为弥散;且载体Al_2_O_3具有一定的结晶性。而以Al_2(SO_4)_3·18H_2O和AlCl_3·6H_2O为铝源制备的NiNO-AlSO和NiNO-AlCl催化剂,其载体以无定型Al_2O_3存在,活性组分Ni晶粒粒径大、分散性差,还原峰面积较小,与载体的相互作用较弱。其中,由于硫酸铝较为稳定,需要在更高温度下才能转化为Al_2O_3,且所制备NiNO-AlSO催化剂中残留有含硫物质,使得其表面酸性较强。评价结果显示,NiNO-AlNO催化剂活性较高,稳定性好,CH4转化率为31.21%,CO_2转化率为48.97%。积炭分析结果发现,NiNO-AlNO催化剂表面积炭量最少,沉积炭主要以无定型态存在,具有良好的抗积炭性能。     

NiMo/Al_2O_3-USY催化剂上中低温煤焦油加氢裂化性能研究

采用等体积浸渍法制得一系列NiMo/Al_2O_3-USY催化剂,在200 mL固定床上考察了不同金属负载量对其中低煤焦油加氢裂化催化性能的影响,进一步用NH_4F溶液改性USY以提高催化剂的脱硫性能,并结合XRD、氮气吸附-脱附、XPS、HR-TEM、H_2-TPR和NH_3-TPD等手段对催化剂进行了表征分析。结果表明,NiM o/Al_2O_3-USY催化剂适宜的M oO_3负载量为15%(质量分数);当MoO_3含量超过15%后,MoS_2活性相在载体上团聚,硫化程度趋于稳定,强酸酸量和孔径减少,增加金属负载量对煤焦油加氢裂化转化率影响较小。NH_4F改性USY可增大NiM o/Al_2O_3-USY催化剂的孔径,有利于提高煤焦油加氢裂化转化率。表面强酸酸量减少后,产品中的硫含量明显增加,说明强酸酸量是影响产物硫含量的关键因素。当NH_4F浓度为0.6 mol/L时,NH_4F改性USY制得的NM 0.6催化剂上煤焦油加氢裂化的转化率为87.65%,产品汽油馏分(≤180℃)硫含量为5.96 mg/kg,柴油馏分(180-320℃)硫含量为34.98 mg/kg。     

Facile Synthesis of Al-pillared Mesoporous Montmorillonite Assisted with Concentrated Al13 Solution

Al-pillared mesoporous montmorillonite was facilely synthesized from concentrated Al13 solution obtained by vacuum concentrating-ultrasonic pillaring strategy.Concentrated Al13 solution could reduce the process of pillare and increase pillaring efficiency.The absolute value of layer distance could be increased by 0.96 nm via concentrated Al13 solution pillare.27Al NMR indicates that Al Keggin ions of concentrated Al13 are arranged in a more regular way by vacuum concentrating method.The Al-pillared mesoporous montmorillonite from concentrated Al13 solution has bigger specific surface area and even pore size distribution which were characterized by X-ray diffraction（XRD） and nitrogen adsorption measurement.Furthermore the catalytic activity of Ai-pillared montmorillonite loaded Ni and Mo catalysts was tested by the hydrodesulfurization of thiophene.The thiophene conversion reached 77.5％,which was higher than the corresponding value reported in the literature.     

三元镍基硫属化物纳米棒阵列的简单合成及其高效的电催化析氧性能北大核心CSCD

通过一步溶剂热法成功合成了泡沫镍(NF)支撑的三元镍基硫属化物(Ni_(3)(Se_(x)S_(1−x))_(2))纳米棒阵列。结构表征结果表明,所得三元Ni_(3)(Se_(x)S_(1−x))_(2)纳米棒属于三方物相,在泡沫镍基底上形成了有序的阵列结构。由于其快速的载流子传输效率、丰富的活性位点和多阴离子的协同效应,Ni_(3)(Se_(0.3)S_(0.7))_(2)/NF纳米棒阵列具有最佳的电催化性能。在1.0 mol/L的KOH溶液中,电流密度为50 mA/cm2时,过电势仅为344 mV,塔菲尔斜率为40.17 mV/dec,同时具有优异的电化学稳定性。更重要的是,以商用Pt/C为阴极,Ni_(3)(Se_(0.3)S_(0.7))_(2)/NF纳米棒阵列为阳极进行全分解水实验,仅需要1.49 V的电池电位即可提供10 mA/cm2的电解电流,表现出良好的电解水效果。该研究为电解水技术领域提供了一种高效的电催化剂,也为电化学能源技术中非贵重电催化剂的合理构建提供了有价值的见解。     

污泥焚烧中铅的形态转化及脱除的热力学平衡研究

利用热力学平衡模型预测了污泥焚烧过程中铅的形态转化和迁移规律, 并采用系统吉布斯自由能最小的原理对Al₂O₃, SiO₂, TiO₂和CaO 4种吸附剂吸附污泥燃烧中铅的效果进行了模拟计算. 探讨了痕量元素Pb与S, Cl的相互作用及S和Cl的存在对吸附剂与Pb反应的影响. 研究结果表明, 污泥焚烧中Pb的形态转化受到S, Cl及矿物质的影响较大. 有S存在情况下, Pb在低温条件下主要以固态PbSO₄存在, 温度较高时以气态PbO存在; Cl较易和Pb结合形成低沸点的金属氯化物而导致Pb的挥发, 并且Cl含量的增加会加速Pb的挥发. 4种吸附剂对污泥焚烧中Pb都有一定的脱除能力, 其中Al₂O₃可以在较宽温度范围对Pb进行捕集, 而CaO对Pb的化学吸附能力较差. 由于S, Cl与Pb有更强的反应性, 因此S, Cl的存在对吸附剂与铅的反应有抑制作用, 使有效吸附的温度范围变窄, 吸附效率降低, 甚至失去脱除Pb的能力, 并且Cl的影响大于S.     

Oxygen species on NiO/Al2O3 and their reactivities

Oxygen species on fresh and treated NiO/Al₂O₃ and their activities for oxidation of ethane and ethylene were investigated using catalytic property measurements, ethane and ethylene pulse experiments and O₂–TPD–MS experiments. The results revealed that there are two kinds of active oxygen species (the more active one and the less active one) on fresh NiO/Al₂O₃ catalyst, but there is only one active oxygen species, the less active one, on treated NiO/Al₂O₃ catalyst. The more active oxygen species can convert ethane or ethylene to carbon dioxide by one step while the less active one can only convert ethane to ethylene, but cannot convert ethane and/or ethylene to carbon dioxide. The more active oxygen species can be removed from the catalyst by heating from 350 to 850 °C. The amounts of desorption oxygen on the catalysts are proportional to their selectivity to carbon dioxide.     

MOF derived Co3O4/N-doped carbon nanotubes hybrids as efficient catalysts for sensitive detection of H2O2 and glucose

Developing enzyme-free sensors with high sensitivity and selectivity for H2O2 and glucose is highly desirable for biological science.Especially,it is attractive to exploit noble-metal-free nanomaterials with large surface area and good conductivity as highly active and selective catalysts for molecular detection in enzyme-free sensors.Herein,we successfully fabricate hollow frameworks of Co3O4/N-doped carbon nanotubes(Co3O4/NCNTs)hybrids by the pyrolysis of metal-organic frameworks followed by calcination in the air.The as-prepared novel hollow Co3O4/NCNTs hybrids exhibit excellent electrochemical performance for H2O2 reduction in neutral solutions and glucose oxidation in alkaline solutions.As sensor electrode,the Co3O4/NCNTs show excellent non-enzymatic sensing ability towards H2O2 response with a sensitivity of 87.40μA(mmol/L)^-1 cm^-2,a linear range of 5.00μmol/L-11.00 mmol/L,and a detection limitation of 1μmol/L in H2O2 detection,and a good glucose detection performance with 5μmol/L.These excellent electrochemical performances endow the hollow Co3O4/NCNTs as promising alternative to enzymes in the biological applications.     

高碳铬铁在氢氧化钠水溶液中电化学氧化过程

铬铁电化学氧化法是一种新的制备铬酸钠的方法,然而高碳铬铁在NaOH水溶液中的电化学氧化过程尚不明确。 采用循环伏安法(CV)、稳态极化法(LSV)等电化学测试方法对金属铬、高碳铬铁在NaOH水溶液中的电化学氧化过程进行研究,通过扫描电子显微镜(SEM)、能量散射谱(EDS)和X射线光电子能谱(XPS)对高碳铬铁电解后固相产物表征,判断固相产物的组成。 结果表明,高碳铬铁不同于金属铬的电氧化过程,它在NaOH溶液中通过Cr(0)→Cr(Ⅵ)的电氧化方式生成铬酸钠,中间产物Cr(OH)₃和Fe(0)发生电化学反应生成稳定的FeCr₂O₄。 随着NaOH浓度的增加,电势较低时,受高碳铬铁中Fe(0)的影响,高碳铬铁容易在NaOH水溶液中发生钝化;当电势足够正时,钝化膜溶解,生成铬酸钠、氢氧化铁和亚铬酸亚铁,同时,阳极表面有氧气析出。 高碳铬铁电化学氧化制备铬酸钠的适宜条件:碱浓度≥2 mol/L,阳极电势≥1.6 V(vs.SCE)。     

生物柴油合成反应中KNO3/Al2O3催化剂的活性物种与失活研究

制备了KNO₃/Al₂O₃负载型固体碱催化剂，通过XRD、DRIFT、低温氮吸附、ICP和碱度滴定等手段对催化剂表面性质进行了表征，研究了其对大豆油与甲醇酯交换制备生物柴油的催化性能，剖析了在反应过程中该催化剂的催化本质以及失活原因。结果表明，高温焙烧后Al₂O₃表面KNO₃完全分解，形成了大量偏铝酸钾分散在载体表面；在酯交换反应时Al₂O₃表面的偏铝酸盐等活性组分不断溶出并参与反应，这是该催化剂表现出高活性的主要原因。在反应过程中生成的产物生物柴油和甘油对催化剂的活性有很大影响，其中，生物柴油与活性物种发生的皂化反应是造成催化剂失活的主要原因。