紫外辐射接枝法修饰聚乳酸表面及其细胞相容性

通过紫外辐射接枝在聚乳酸膜表面引入聚丙烯酸的方法使聚乳酸材料表面的亲水性和细胞相容性得到改善,研究了各种处理条件对材料表面的羧基密度、表面形态和表面接触角的影响,同时还考察了紫外辐射接枝聚丙烯酸的聚乳酸表面的成骨细胞相容性.红外光谱分析和羧基密度测定结果表明:通过紫外光引发接枝,聚丙烯酸被成功接枝到聚乳酸表面,而且接枝密度受接枝时间和聚丙烯酸质量分数的影响很大.接触角和原子力显微镜研究结果表明:接枝聚丙烯酸后的聚乳酸表面的亲水性和粗糙度明显增加,能够促进成骨细胞的生长.     

海绵状纳米结构TiO2膜的制备及其光催化活性

采用电化学阳极氧化法在钛表面构筑了海绵状纳米结构TiO2膜. 应用扫描电子显微镜(SEM)和X射线衍射(XRD)对膜层的形貌和晶型进行了分析和表征, 考察了阳极氧化时间对膜层厚度的影响, 并通过海绵状纳米结构TiO2膜对甲基橙的光催化降解研究了膜层厚度与光催化活性的关系. 结果表明, 海绵状纳米结构TiO2膜对甲基橙具有光催化降解作用, 而且随着膜层厚度的增加, 光催化降解速率显著增大, 厚度为2.2 μm的海绵状纳米结构TiO2膜对甲基橙的光催化降解速率是厚度为480 nm的6.4倍.     

纳米α-Fe_2O_3-TiO_2改性海藻酸钠/壳聚糖双极膜制备与表征

在壳聚糖(CS)阴离子交换膜中添加纳米复合半导体材料α-Fe2O3-TiO2,制备了PVA-SA/α-Fe2O3-TiO2-CS双极膜(PVA:聚乙烯醇;SA:海藻酸钠),并用扫描电镜、热重分析、电子万能试验机和接触角测定仪等对其进行了表征。研究结果表明,添加纳米α-Fe2O3-TiO2可提高双极膜的亲水性、热稳定性和机械性能。纳米α-Fe2O3-TiO2复合半导体材料较纳米α-Fe2O3或纳米TiO2单一半导体材料具有更强的光催化双极膜中间界面层水解离能力,在高压汞灯照射下能大大降低双极膜的膜阻抗和膜电阻压降(IR降)。     

接枝丙烯酰胺改善聚乙烯膜表面亲水性的研究

利用等离子体技术和紫外照射接枝相结合在聚乙烯膜表面接枝丙烯酰胺(AAm)以改善其亲水性。通过衰减全反射红外光谱(ATR-FTIR)、X射线光电子能谱(XPS)和接触角测定验证了在无光引发剂的条件下,将等离子体预处理和紫外照射接枝结合起来可以有效地提高AAm的接枝效果,很好地改善PE膜表面的亲水性。探讨了等离子体复合参数W/(FM)、等离子体预处理时间、AAm单体浓度以及紫外照射时间对改善PE膜表面亲水性的影响,确定改善PE膜表面亲水性的最佳实验条件。     

Nafion膜表面亲水性研究

Ｎａｆｉｏｎ膜在电化学体系中的应用越来越广泛,而其表面亲水性往往直接影响着使用性能．本文介绍一种适宜于表征Ｎａｆｉｏｎ膜表面亲水性的接触角测量方法,即束缚气泡法,并讨论了该膜与水溶液接触角的滞后现象、溶液表面张力的影响,简介了用全氟表面活性剂改善Ｎａｆｉｏｎ膜表面亲水性的尝试．     

聚丙烯表面接枝PNIPAAm膜Ⅱ.表面特性和温度响应性研究

通过吸水率和接触角测定研究了聚N 异丙基丙烯酰胺 (PNIPAAm)接枝膜的温度敏感特性 .尽管非交联型接枝膜和交联型接枝膜的吸水特性没有显著差别 ,但是交联组分的引入确实在一定程度上延缓了接枝膜的失水趋势 ,同时也有利于接枝膜亲水性的提高 .对接枝膜进行接触角研究发现 ,在某临界温度以下 ,接触角随时间的变化表征了探测水滴与膜表面之间的相互作用过程 .为了消除接触角测定过程中水份蒸发造成的影响 ,建立了接触角修正算法和修正经验关系式 ,并发展了一种适合于温度敏感性接枝膜LCST测定的变温实时接触角测定方法 .提出了接枝膜与水滴相互作用过程分为两个阶段的模型 ,并得到交联型PP接枝膜表面性能发生明显变化的临界接枝率为 0 6mg cm2 左右     

丙烯酸水溶液聚合法制备PTFE/PAA/Nafion膜及其性能

采用廉价的多孔聚四氟乙烯(PTFE)膜作为基底, 用少量的Nafion与PTFE膜复合可制备低成本的质子膜. 但疏水性的PTFE膜与亲水性的Nafion膜结合性不佳. 基于此, 本文对疏水性的PTFE膜材料表面进行设计, 先采用丙烯酸对疏水性的PTFE膜表面进行亲水性改性, 再喷涂亲水性Nafion膜, 完成低成本PTFE/PAA/Nafion膜的制备. 实验结果表明, 改性前的PTFE膜材料水接触角为150°, 改性后的膜接触角变为55.6°, 亲水性大幅上升, 膜的机械强度和尺寸稳定性(断裂强度为25.2 MPa, 80 ℃下的溶胀率为11.9%)均优于Nafion117膜, 而 Nafion用量则节省了60%. PTFE/PAA/Nafion膜具有高质子导通率(80 ℃下达到131.9 mS/cm), 接近于Nafion117膜, 最大功率密度可以达到404.2 mW/cm².     

PVDF亲水复合膜的制备及表征

聚偏氟乙烯(PVDF)膜材料存在强疏水性的缺陷,亲水化改性是解决该问题的主要途径。以PVDF为基膜材料、聚乙烯醇(PVA)为共混材料、N,N-二甲基乙酰胺(DMAc)为溶剂,采用相转化法制备PVDF/PVA复合膜。考察了复合膜的PVDF/PVA共混比、固含量、低分子化合物添加剂、聚合物添加剂等非溶剂添加剂对复合膜接触角的影响。结果表明,当PVDF/PVA共混比为7/3,固含量为13%时,制备的复合膜接触角为22.92°;当添加剂为无水氯化锂、纳米二氧化硅、聚乙烯吡咯烷酮(PVP)时,复合膜接触角分别从53.12°、30.51°和41.89°都降低到了0°,亲水性提高,其中纳米二氧化硅作为添加剂时复合膜亲水性最好;当添加剂为丙三醇、PMMA、PEG时,复合膜接触角都增大,亲水性变差。     

疏水型SiO2光学增透膜的制备

以正硅酸乙酯（TEOS）为有机醇盐前驱体,采用溶胶-凝胶技术,通过酸/碱二步法控制实验条件,结合三甲基氯硅烷（TMCS）对胶粒表面的修饰过程,制备出结构可控的疏水型SiO2薄膜.采用椭偏仪、FTIR、接触角测试仪、SEM等对薄膜的折射率、红外特性、接触角以及表面形貌等进行了测量.研究结果表明,疏水型SiO2薄膜的折射率在1.33～1.18之间连续可调;SiO2胶粒表面的亲水性－OH中的H已部分被非活性－Si(CH3)3基团取代;接触角由表面未修饰膜的40°左右增加到表面修饰膜的120°左右.     

TiO2负载膜的制备、表征及光催化性能

采用溶胶－凝胶法制备了ＴｉＯ２纳米浸渍 法将其负载于颗粒形活性炭的表面制成ＴｉＯ２负载,利用ＳＥＭ,ＥＤＳ和ＸＲＤ等手段对膜的形貌、均匀性及晶型等进行了表征,并通过甲基橙水溶液的光催化降解反应考察了该负载膜的光催化活性。     

Photocatalytic properties of titania nanostructured films fabricated from Titania nanosheets

We examined the photochemical properties of well-ordered multilayer films of titania nanosheets prepared on quartz-glass substrate using the layer-by-layer deposition method. The photocatalytic decomposition of gaseous 2-propanol and bleaching of Methylene Blue dye under UV light illumination were measured to evaluate the photocatalytic oxidation ability. Photoinduced hydrophilicity was also studied by measuring the contact angle of water droplets on the film. The results indicated that titania nanosheets had good photoinduced hydrophilicity. The monolayer film of titania nanosheets showed almost identical activity compared with well investigated sol-gel derived anatase TiO(2) film, while its photocatalytic oxidation activity was low by more than an order of magnitude. This fact suggests that photoinduced hydrophilicity could not be explained simply in terms of the photocatalytic removal of hydrophobic organic species adsorbed on the surface. The photocatalytic oxidation activity and the photoinduced hydrophilic conversion rate decreased with increasing number of nanosheet layers, suggesting that photogenerated carriers produced in the internal part of the multilayer films can hardly diffuse to the surface layer. Photochemical properties of ultrathin anatase films obtained simply by heating the titania nanosheet films were evaluated as well, and also revealed high photoinduced hydrophilicity.     

Improving hydrophilicity and protein resistance of poly(vinylidene fluoride) membranes by blending with amphiphilic hyperbranched-star polymer

To endow hydrophobic poly(vinylidene fluoride) (PVDF) membranes with reliable hydrophilicity and protein resistance, an amphiphilic hyperbranched-star polymer (HPE-g-MPEG) with about 12 hydrophilic arms in each molecule was synthesized by grafting methoxy poly(ethylene glycol) (MPEG) to the hyperbranched polyester (HPE) molecule using terephthaloyl chloride (TPC) as the coupling agent and blended with PVDF to fabricate porous membranes via phase inversion process. The chemical composition changes of the membrane surface were confirmed by X-ray photoelectron spectroscopy (XPS), and the membrane morphologies were measured by scanning electron microscopy (SEM). Water contact angle, static protein adsorption, and filtration experiments were used to evaluate the hydrophilicity and anti-fouling properties of the membranes. It was found that MPEG segments of HPE-g-MPEG enriched at the membrane surface substantially, while the water contact angle decreased as low as 49 degrees for the membrane with a HPE-g-MPEG/PVDF ratio of 3/10. More importantly, the water contact angle of the blend membrane changed little after being leached continuously in water at 60 degrees C for 30 days, indicating a quite stable presence of HPE-g-MPEG in the blend membranes. Furthermore, the blend membranes showed lower static protein adsorption, higher water and protein solution fluxes, and better water flux recovery after cleaning than the pure PVDF membrane.     

多孔TiO2薄膜自洁净玻璃的亲水性和光催化活性

亲水性多孔TiO₂薄膜自洁净玻璃以含聚乙二醇的钛醇盐溶胶前驱体中通过浸渍提拉法制备;随着前驱物中聚乙二醇加入量的增加,多孔TiO₂薄膜表面的羟基含量也增加,薄膜表面的亲水性增强,水与薄膜表面的接触角下降为0°.该亲水性多孔TiO₂薄膜自洁净玻璃具有明显的自洁净和易清洗功能.紫外-可见光透过光谱分析表明,随着TiO₂薄膜中孔径的增大,光的散射增强,透光率减小.该TiO₂镀膜玻璃对于紫外线具有吸收作用.甲基橙水溶液的光催化降解实验表明,在TiO₂薄膜中引入适当大小的微孔可显著增强薄膜的光催化活性,但当孔径接近400nm时,薄膜的光催化活性减弱.     

不同波长紫外光照下纳米TiO2薄膜的光致亲水性与循环伏安行为

通过溶胶-凝胶方法分别在ITO和玻璃表面制备了纳米TiO_2薄膜，研究了纳米 TiO_2薄膜在254及365nm的紫外光照射下的循环伏安行为和光致超亲水性。在紫外 光的照射下，TiO_2薄膜电极可表现出两个光电化学过程，纳米TiO_2薄膜的光致超 亲水性转变及两个光电化学过程的速率均取决于紫外光的波长，原因在于纳米 TiO_2薄膜对两种波长的光的吸收率和光子的能量不同。提出了光电化学过程的机 理，认为紫外光照射下纳米TiO_2薄膜的超亲水性变化与产生Ti~(3+)的过程引起的 表面微观结构变化存在的一定的内在联系。     

Amphiphile grafted membranes for the separation of oil-in-water dispersions

Perfluorinated end-capped polyethylene glycol surfactants were covalently attached to fritted glass membranes as a means to improve the separation of oil-in-water emulsions. Hexadecane was used as representative oil for the oil-in-water emulsions; membrane pore size was varied between 10 and 174 microm. Membranes were characterized with respect to contact angle, permeability of bulk fluids, and separation efficiency. Performance was compared to similar metrics applied to unmodified membranes. Modified membranes demonstrated static hexadecane contact angles which were higher than static water contact angles converse to their unmodified counterparts. The relative hydrophilicity and corresponding oleophobicity of the modified membranes resulted in greater water permeability as compared to hexadecane permeability. The presence of the perfluorinated constituent of the amphiphile retarded the flow of hexadecane. For modified membranes, suspended hexadecane coalesced at the membrane surface, was undercut by water, and floated to the surface such that only trace amounts of oil were present in the permeate. Therefore, modified membranes resisted fouling from oil due to the self-cleaning properties of the attached amphiphile.     

Fabrication,characterization, and performance evaluation of polyethersulfone/TiO2 nanocomposite ultrafiltration membranes for produced water treatment

In the present work, development of neat and nanocomposite polyethersulfone membranes composed of TiO₂ nanoparticles is presented. Membranes are fabricated using nonsolvent phase inversion process with the objective of improving antifouling, hydrophilicity, and mechanical properties for real and synthetic produced water treatment. Membranes are characterized using scanning electron microscopy, Fourier‐transform infrared, contact angle, porosity measurement, compaction factor, nanoparticles stability, and mechanical strength. The performance of prepared membranes was also characterized using flux measurement and oil rejection. Fourier‐transform infrared spectra indicated that noncovalence bond formed between Ti and polyethersulfone chains. The contact angle results confirmed the improved hydrophilicity of nanocomposite membranes upon addition of TiO₂ nanoparticles owing to the strong interactions between fillers and water molecules. The increased water flux for nanocomposite membranes in comparison with neat ones can be due to coupling effects of improved surface hydrophilicity, higher porosity, and formation of macrovoids in the membrane structure. The membrane containing 7 wt% of TiO₂ nanoparticles was the best nanocomposite membrane because of its high oil rejection, water flux, antifouling properties, and mechanical stability. The pure water flux for this membrane was twice greater than that of neat membrane without any loss in oil rejection. The hydrophilicity and antifouling resistance against oil nominates developed nanocomposite membranes for real and synthetic produced water treatment applications with high performance and extended life span.     

海藻糖改性聚乙烯醇及其防雾/防霜涂层

以聚乙烯醇和羧基化海藻糖为原料合成了聚乙烯醇-g-海藻糖(PVA-g-Tre), 将接枝物与少量乙二醇二甲基丙烯酸酯混合, 通过光引发聚合制备了亲水性半互穿网络防雾/防霜涂层. 通过核磁共振氢谱和傅里叶变换红外光谱对PVA-g-Tre的化学结构进行了表征, 利用原子力显微镜、 水接触角测试仪、 拉曼光谱等分析了涂层表面的粗糙度、 润湿性及水与大分子之间的氢键作用, 并考察了涂层的透光性和防雾及防霜性能. 结果表明, 含有不同海藻糖接枝率PVA-g-Tre的涂层表面粗糙度较低且透光率好, 与含有PVA的涂层相比, 引入海藻糖提高了PVA-g-Tre涂层的亲水性和润湿性, 使其同时具有良好的防雾和防霜性能.     

基于多巴胺自聚合与表面接枝PHGH制备抗菌纳滤膜

在水溶液中将聚六亚甲基单胍盐酸盐(PHGH)共价接枝在经多巴胺自聚合改性的聚砜膜表面, 制备具有抗菌性能的纳滤膜. 采用全反射红外光谱(ATR-FTIR)、 扫描电子显微镜(SEM)和接触角测试考察膜表面的结构、 形貌和亲水性变化. 探讨PHGH含量对膜的接枝度及分离性能的影响, 并对膜的抗菌性能进行了评价. 结果表明, 经过多巴胺的自聚合和表面接枝PHGH后, 聚砜膜表面形成了具有纳滤分离性能的活性层, 并且膜表面亲水性得到改善. 随着PHGH含量的增大, 膜的纯水通量降低, 而对无机盐和染料的截留性能提高. 接枝后的复合膜具有较高的抗菌性能, 当PHGH含量为3%(质量分数)时, 抗菌率可达98.5%.     

Preparation of high density polyethylene/polyethylene-block-poly(ethylene glycol) copolymer blend porous membranes via thermally induced phase separation process and their properties

<正>High density polyethylene(HDPE)/polyethylene-block-poly(ethylene glycol)(PE-b-PEG) blend porous membranes were prepared via thermally induced phase separation(TIPS) process using diphenyl ether(DPE) as diluent.The phase diagrams of HDPE/PE-b-PEG/DPE systems were determined by optical microscopy and differential scanning calorimetry(DSC).By varying the content of PE-b-PEG,the effects of PE-b-PEG copolymer on morphology and crystalline structure of membranes were studied by scanning electron microscopy(SEM) and wide angle X-ray diffraction(WAXD). The chemical compositions of whole membranes and surface layers were characterized by elementary analysis,Fourier transform infrared spectroscopy-attenuated total reflection(FTIR-ATR) and X-ray photoelectron spectroscopy(XPS).Water contact angle,static protein adsorption and water flux experiments were used to evaluate the hydrophilicity,antifouling and water permeation properties of the membranes.It was found that the addition of PE-b-PEG increased the pore size of the obtained blend membranes.In the investigated range of PE-b-PEG content,the PEG blocks could not aggregate into obviously separated domains in membrane matrix.More importantly,PE-b-PEG could not only be retained stably in the membrane matrix during membrane formation,but also enrich at the membrane surface layer.Such stability and surface enrichment of PE-b-PEG endowed the blend membranes with improved hydrophilicity,protein absorption resistance and water permeation properties,which would be substantially beneficial to HDPE membranes for water treatment application.     

PREPARATION OF HIGH DENSITY POLYETHYLENE/POLYETHYLENE-ΒLOCK- POLY(ETHYLENE GLYCOL) COPOLYMER BLEND POROUS MEMBRANES VIA THERMALLY INDUCED PHASE SEPARATION PROCESS AND THEIR PROPERTIES

High density polyethylene (HDPE)/polyethylene-Wock-poly(ethylene glycol) (PE-b-PEG) blend porous membranes were prepared via thermally induced phase separation (TIPS) process using diphenyl ether (DPE) as diluent. The phase diagrams of HDPE/PE-b-PEG/DPE systems were determined by optical microscopy and differential scanning calorimetry (DSC). By varying the content of PE-b-PEG, the effects of PE-b-PEG copolymer on morphology and crystalline structure of membranes were studied by scanning electron microscopy (SEM) and wide angle X-ray diffraction (WAXD). The chemical compositions of whole membranes and surface layers were characterized by elementary analysis, Fourier transform infrared spectroscopy-attenuated total reflection (FTIR-ATR) and X-ray photoelectron spectroscopy (XPS). Water contact angle, static protein adsorption and water flux experiments were used to evaluate the hydrophilicity, antifouling and water permeation properties of the membranes. It was found that the addition of PE-b-PEG increased the pore size of the obtained blend membranes. In the investigated range of PE-b-PEG content, the PEG blocks could not aggregate into obviously separated domains in membrane matrix. More importantly, PE-b-PEG could not only be retained stably in the membrane matrix during membrane formation, but also enrich at the membrane surface layer. Such stability and surface enrichment of PE-b-PEG endowed the blend membranes with improved hydrophilicity, protein absorption resistance and water permeation properties, which would be substantially beneficial to HDPE membranes for water treatment application.