导尿管表面具有抗菌功能的层层组装微凝胶膜

以化学交联的聚烯丙基胺盐酸盐拟葡聚糖微凝胶和透明质酸为构筑基元,在导尿管表面层层组装构筑了厚度小于500 nm可控释放抗菌药物的聚合物微凝胶膜。 广谱抗菌药物头孢曲松钠通过扩散吸附的方法在2 min内快速负载到聚合物微凝胶膜中,并且在生理盐水中可控释放时间达3 h。 抗菌实验表明,组装有层层组装微凝胶膜并负载广谱抗菌药物的导尿管具有令人满意的抗菌效果,避免感染的发生。     

图案化自组装膜导向的电沉积

通过图案化自组装膜导向的电沉积制备了聚吡咯(PPy)微结构. 由微接触印刷方法制备图案化自组装膜并作为电沉积的模板. 研究发现, 自组装膜在导向电沉积中在不同的基底上具有不同的作用: 在十二烷基硫醇(DDT)、十八烷基硫醇(ODT)修饰的金基底上和十八烷基三氯硅烷(OTS)修饰的铟锡氧化物玻璃上(ITO), 电沉积主要发生在自组装膜未修饰区, 而在半导体单晶硅表面, PPy沉积在OTS修饰区, 是基底表面的导电性及PPy与基底表面基团相容性共同作用的结果.     

表面活性剂胶束实现疏水分子在聚合物微凝胶层层组装膜中的高效负载

基于层层组装技术制备了聚烯丙基胺-葡聚糖微凝胶(记作PAH-D)/透明质酸钠(HA)膜, 将包覆有芘分子的十二烷基硫酸钠(SDS)表面活性剂胶束基于静电作用力负载到PAH-D/HA微凝胶膜中, 实现了疏水分子芘在微凝胶膜中的高效负载. 紫外-可见吸收光谱和荧光光谱证实了SDS胶束包覆的芘分子被稳定地负载在PAH-D微凝胶膜中. 透过光谱表明负载有芘分子的(PAH-D/HA)*10微凝胶膜在可见光区仍保持良好光学透过性. 芘在膜中的负载量可以通过改变PAH-D/HA微凝胶膜的沉积周期数和SDS胶束中包覆芘分子的浓度而实现调控. 具有光致变色性质的螺吡喃分子同样可以借助SDS胶束负载到PAH-D/HA微凝胶膜中, 制备具有光致变色性质的层层组装膜. 本工作为疏水有机分子在层层组装聚合物膜中的高效负载提供了一种简便、易行的方法.     

聚合物层状组装膜

介绍了近几年来我们研究组在层状组装膜的构筑以及功能化研究方面取得的一些最新进展.包括结合表面溶胶-凝胶技术与静电层状组装技术,实现了二阶非线性基团在层状组装多层膜中的非对称排列,制备了具有二阶非线性效应的膜材料;采用室温压印技术,发展了一种简便、经济和具有普适性的层状组装聚合物膜图案化方法;以轻度交联的聚合物微凝胶为构筑基元,制备了具有高负载量的聚合物层状组装膜;发展了一种基于离子剥离技术的层状组装自支持膜制备方法;基于层状组装技术,制备了具有超疏水和抗反射功能的涂层.     

一步法制备PNIPAAm-g-PAN/PSt载银复合微球及其抗菌性能研究

以AgNO3为金属源,通过乙醇将与聚N-异丙基丙烯酰胺接枝聚丙烯腈/聚苯乙烯（PNIPAAm-g-PAN/PSt）聚合物微球表面酰胺基团配位的银离子（Ag+）还原,一步法制备了PNIPAAm-g-PAN/PSt载银复合微球。通过傅立叶变换红外（FTIR）和紫外-可见光光谱表征发现,由Ag+还原所得的Ag纳米颗粒被成功地固载在PNIPAAm-g-PAN/PSt 微球上;用透射电子显微镜（TEM）对载银微球的大小和形态进行了表征;热重分析（TGA）结果表明,固载在微球表面的银纳米颗粒的含量（质量分数）为12%;抗菌实验结果表明,所制备的载银微球具有抗革兰氏阴性菌的活性。     

纳米半导体硫化银单层膜的自组装

本文使用Triton X-100作为模板剂制备半导体硫化银纳米颗粒,并研究了其吸收光谱的兰移特性。在金属铝或金基底上自组装有机双功能分子单层膜后,将其浸入所制备的纳米硫化银颗粒的微乳液中,自组装得到硫化银纳米颗粒单层膜并研究了其表面形貌特征。     

用简便方法组装二维模板银纳米阵列

通过制备甲基和羧基混合自组装单层膜, 然后在羧基基团上选择性地生长银制备二维模板银纳米阵列. 利用微接触印刷在金膜上制备模板自组装单层膜, 也就是利用具有二维微米图案的弹力印模把有机巯基化合物转移到金膜上. 改善的银镜反应被用来制备银纳米结构, 银纳米粒子选择性地生长在二维模板有机单分子层的羧基位置. 甲醇作为还原剂具有高的选择性和原子经济性, 一分子甲醇可以还原六个银离子. 利用原子力显微镜和扫描电子显微镜确定了银纳米结构的形貌, 用拉曼光谱研究银纳米结构的光学性质.     

银纳米颗粒@二氧化硅微球SERS基底的制备

采用溶胶-凝胶技术制备富含巯基的二氧化硅微球,在其表面原位合成银纳米颗粒,将其作为表面增强拉曼散射(Surface-enhanced Raman scattering,SERS)的活性基底材料,重点讨论了银纳米颗粒作为"热点"对SERS性能的影响。银纳米颗粒的原位生成导致微球表面粗糙化,致密的纳米颗粒能够形成更多的热点,分别采用透射电镜、扫描电镜、X射线光电子能谱、Raman等对银纳米颗粒在微球表面生长状况进行了表征。结果表明,微球表面的巯基直接导致银纳米颗粒的生长,并为银纳米颗粒的稳定性提供了还原性环境。     

建立在硫醇分子电化学替换组装基础上的纳米粒子区域化组装

利用金基底电位变化时硫醇自组装膜的吸脱附性质, 通过改变基底电位和组装溶液, 用电化学方法在金基底上实现了传统自组装技术难以实现的硫醇分子的替换组装; 通过金基底的分区化设计, 用控制电位的组装技术在基底的不同微区内制备了不同末端官能团的硫醇及其衍生物自组装膜; 并在此基础上实现了纳米粒子的区域化组装.     

表面增强拉曼光谱研究基于轴向配位键结合的金属卟啉自组装膜

选择一种金属卟啉有机物(5-对-烷氧基苯基-10,15,20-三苯基卟啉羟基稀土化合物, HoOH)和4,4'-联吡啶(44BPY)作为自组装膜的基本构筑单元, 利用金属配位作用, 成功地将HoOH单分子膜组装到44BPY修饰的银表面. 采用紫外-可见吸收光谱、表面增强拉曼光谱研究了金属卟啉自组装膜的形成并且探索其结构和取向的变化. 结果表明, 底层的44BPY通过4位的N原子垂直吸附到银表面, 另一端的吡啶环上的N原子与HoOH的金属中心配位形成化学键. 从而在44BPY长轴向方向上将HoOH连接到44BPY自组装膜上, 并形成了新的交替膜. 之后, 底层的44BPY取向发生变化, 更向基底倾斜, 而上层的HoOH的分子平面则近乎平行于基底.     

Assembly of poly(N-isopropylacrylamide)-co-acrylic acid microgel thin films on polyelectrolyte multilayers: Effects of polyelectrolyte layer thickness, surface charge, and microgel solution pH

Temperature- and pH-sensitive poly(N-isopropylacrylamide)?Cco-acrylic acid (pNIPAm-co-AAc) microgels were deposited on glass substrates coated with polyelectrolyte multilayers composed of the polycation poly(allylamine hydrochloride) (PAH) and the polyanion poly(sodium 4-styrenesulfonate) (PSS). The microgel density and structure of the resultant films were investigated as a function of: (1) the number of PAH/PSS layers (layer thickness); (2) the charge on the outer layer of the polyelectrolyte multilayer film; and (3) the pH of microgel deposition solution. The resultant films were studied by differential interference contrast optical microscopy, atomic force microscopy, and scanning electron microscopy. It was found that the coverage of the microgels on the surface was a complex function of the pH of the deposition solution, the charge on the outer layer of the polyelectrolyte thin film and the PAH/PSS layer thickness; although it appears that microgel charge plays the biggest role in determining the resultant surface coverage.     

Layer-by-layer assembled microgel films with high loading capacity: reversible loading and release of dyes and nanoparticles

Multilayer films containing microgels of chemically cross-linked poly(allylamine hydrochloride) (PAH) and dextran (named PAH-D) were fabricated by layer-by-layer deposition of PAH-D and poly(styrene sulfonate) (PSS). The successful fabrication of PAH-D/PSS multilayer films was verified by quartz crystal microbalance measurements and cross-sectional scanning electron microscopy. The as-prepared PAH-D/PSS multilayer films can reversibly load and release negatively charged dyes such as methyl orange (MO) and fluorescein sodium and mercaptoacetic acid-stabilized CdTe nanoparticles. The loading capacity of the film for MO can be as large as approximately 3.0 microg/cm2 per bilayer, which corresponds to a MO density of 0.75 g/cm3 in the film. The high loading capacity of the PAH-D/PSS films originates from the cross-linked film structure with sufficient binding groups of protonated amine groups, as well as their high swelling capability by solvent. The loaded material can be released slowly when immersing the films in 0.9% normal saline. Meanwhile, the PAH-D/PSS multilayer films could deposit directly on either hydrophilic or hydrophobic substrates such as quartz, polytetrafluoroethylene, polystyrene, poly(ethylene terephthalate), and polypropylene. The microgel films of PAH-D/PSS are expected to be widely useful as matrixes for loading functional guest materials and even for controlled release.     

Roll‐to‐Roll printed PEDOT/PSS/GO Plastic Film for Electrochemical Determination of Carbofuran

In this work, we developed a roll‐to‐roll printed poly(3,4‐ethylenedioxythiophene)/polystyrene sulphoanate without graphene oxide (GO) (PEDOT/PSS) and with graphene oxide (PEDOT/PSS/GO) plastic films for the electrochemical determination of carbofuran. Both the PEDOT/PSS and PEDOT/PSS/GO plastic films showed electroactivity towards the oxidation of carbofuran. Incorporation of graphene oxide (GO) improves the electrochemical activity of carbofuran and increased its sensitivity. The printed plastic films were characterized by cyclic voltammetry (CV), linear sweep voltammetry (LSV), surface profilometer, four point probe and atomic force microscopy (AFM). The effects of pH, deposition time, deposition potential and film thickness on the oxidation peak current of carbofuran were investigated. Under the optimized conditions, a dynamic linear range of 1 μM–90 μM with a detection limit of 1.0×10^?7 M (S/N=3) were obtained. The printed PEDOT/PSS/GO plastic electrode was applied for the determination of carbofuran in vegetable and fruit samples with recoveries between 94.4 and 101.8 %.     

High-flux nanofiltration membranes prepared by adsorption of multilayer polyelectrolyte membranes on polymeric supports

Layer-by-layer deposition of anionic and cationic polyelectrolytes readily converts polymeric ultrafiltration membranes into materials capable of nanofiltration. ATR-FTIR spectra confirm that layer-by-layer deposition occurs on the ultrafiltration substrates, and adsorption of as few as 2.5 bilayers of poly(styrenesulfonate) (PSS)/protonated poly(allylamine) (PAH) or 3.5 bilayers of PSS/poly(diallyldimethylammonium chloride) (PDADMAC) reduces the molecular weight cutoff of polyethersulfone ultrafiltration supports from 50 kDa to <500 Da. Deposition of multilayer polyelectrolyte films on 300 and 500 kDa membranes also decreases molecular weight cutoffs, but solute rejections are significantly lower when using these supports, suggesting that the polyelectrolyte films do not completely cover large (0.2-0.4 microm in diameter) pores. On the 50 kDa substrates, PSS/PDADMAC films containing 3.5 bilayers exhibit a 95% rejection of SO(4)(2-) and a chloride/sulfate selectivity of 27, whereas 4.5-bilayer PSS/PAH coatings show a glucose/raffinose selectivity of 100. Pure water flux for [PSS/PAH](3)PSS-coated membranes at 4.8 bar is 1.6 m(3)/(m(2)day), which is more than 2-fold higher than that through a commercial 500 Da membrane.     

Colloid surface engineering via deposition of multilayered thin films from polyelectrolyte blend solutions

Multilayer thin films were constructed on polystyrene colloidal particles by depositing alternating layers of poly(allylamine hydrochloride) (PAH) at pH 7.5 and varying composition blends of poly(acrylic acid) (PAA) and poly(styrenesulfonate) (PSS) at pH 3.5. Following the deposition of each layer, microelectrophoresis experiments showed alternating zeta-potentials, suggesting the formation of multilayered films on the particles. Scanning and transmission electron microscopy were used to examine the surface morphology of the colloidal particles, with homogeneous surface coatings apparent for films deposited from PAA/PSS blend solutions containing up to 90 wt % PAA. The colloidal stability of these particles is greater than those coated with individual PAH and PAA layers. In the case of the blend PAA/PSS = 25:75 wt %, up to 20 layers were assembled without compromising the colloidal stability of the dispersion. The results demonstrate that the deposition of layers from PE blend solutions containing a strong and weak PE can be used as a facile method for controlling the surface properties and hence the colloidal stability of core-shell particles, as well as the thickness and morphology of the coatings. Control of these parameters is important for subsequent processing and application of these particles in controlled delivery, photonics, catalytic, and separation applications.     

Polystyrene latex deposition onto polyethylene film consecutively treated with cationic and anionic polymer

The effects of treating polyethylene (PE) film by consecutive adsorption of poly(diallyldimethylammonium chloride), polyDADMAC, followed by poly(sodium p-styrene sulfonate), PSS, on the deposition rate of aqueous polystyrene latex were investigated with the impinging jet technique. Rapid initial deposition occurred on films treated with polyDADMAC; however, significant blocking occurred. Deposition decreased with the concentration of polyDADMAC used to treat the PE film.

Film treatment with polyDADMAC followed by PSS to give an adsorbed polyelectrolyte complex gave decreased deposition rates. The molecular weight of PSS was not a significant variable in the range 5400–1 200 000. It was concluded that PSS increased the electrostatic repulsion between the PE film and the latex particles.     

Ion-exchange voltammetry with nafion/poly(sodium 4-styrenesulfonate) mixed coatings on mercury film electrodes: characterization studies and application to the determination of trace metals

This work aimed to produce improved polymer coatings for the modification of thin mercury film electrodes (TMFEs). The goal is to obtain sensitive, reproducible, mechanically stable and antifouling devices suitable for the determination of trace metal cations in complex media. Therefore, novel mixed coatings of two sulfonated cation-exchange polymers of dissimilar characteristics-Nafion (NA) and poly(sodium 4-styrenesulfonate) (PSS)-were produced by solvent evaporation onto glassy carbon electrodes. The effect of the mass ratio (NA:PSS) on the film morphology was studied by scanning electron microscopy, revealing the formation of biphasic polymer systems, where PSS bead-shaped clusters appeared randomly dispersed into a uniform and compact NA environment. The permselectivity/ion-exchange features of the mixed films onto glassy carbon were evaluated using cathecol, urate, and dopamine. To allow trace metal analysis, thin mercury films were plated through the NA/PSS coatings, being the reproducibility and ion-exchange features of the mixed coatings-TMFE evaluated using lead ions. The best NA/PSS coating was found for the mass ratio of 5.3. Analytical performance of the NA/PSS-TMFE yielded a detection limit of 5.5 nM (3sigma), and the application of this modified electrode to an untreated polluted estuarine water sample produced significant improvements in the quality of the signal compared with that for a bare TMFE.     

Separation of fluoride from other monovalent anions using multilayer polyelectrolyte nanofiltration membranes

Nanofiltration (NF) is an attractive technique for reducing F- concentrations to acceptable levels in drinking water, but commercial NF membranes such as NF 270 and NF 90 show minimal Cl-/F- selectivity. In contrast, simple layer-by-layer deposition of 4.5-bilayer poly(styrene sulfonate) (PSS)/poly(diallyldimethylammonium chloride) (PDADMAC) films on porous alumina supports yields NF membranes that exhibit Cl-/F- and Br-/F- selectivities>3 along with solution fluxes that are >3-fold higher than those of the commercial membranes. Fluoride rejection by (PSS/PDADMAC)4PSS membranes, which is >70%, is independent of pressure over a range of 3.6 to 6.0 bar, suggesting that the primary transport mechanism in these films is convection. Moreover, the fact that Br-/F- selectivity is 12% higher than Cl-/F- selectivity suggests that discrimination among the monovalent ions is based on size (Stokes radius). Chloride/fluoride selectivities are essentially constant over Cl-/F- feed ratios from 1 to 60, so these separations will be viable over a range of conditions. Interestingly, PSS/protonated poly(allylamine) films show little Cl-/F- selectivity, and the selectivity of PSS/PDADMAC membranes is a strong function of the number of deposited layers, indicating that NF properties are very sensitive to film structure.     

Layer-by-layer assembly of salt-containing polyelectrolyte complexes for the fabrication of dewetting-induced porous coatings

The layer-by-layer (LbL) assembly of salt-containing nonstoichiometric polyelectrolyte complexes (PECs) with oppositely charged uncomplexed polyelectrolyte for the fabrication of dewetting-induced porous polymeric films has been systematically investigated. Salt-containing poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) complexes (noted as PAH-PAA) with a molar excess of PAH were LbL assembled with polyanion poly(sodium 4-styrenesulfonate) (PSS) to produce PSS/PAH-PAA films. The structure of the PAH-PAA complexes is dependent on the concentration of NaCl added to their aqueous dispersions, which can be used to tailor the structure of the LbL-assembled PSS/PAH-PAA films. Porous PSS/PAH-PAA films are fabricated when salt-containing PAH-PAA complexes with a large amount of added NaCl are used for LbL assembly with PSS. In-situ and ex-situ atomic force microscopy measurements disclose that the dewetting process composed of pore nucleation and pore growth steps leads to the formation of pores in the LbL-assembled PSS/PAH-PAA films. The present study provides a facile way to fabricate porous polymeric films by dewetting LbL-assembled polymeric films comprising salt-containing PECs.