基于CoFe2O4载氧体的生物质化学链气化热力学分析及实验研究

对基于CoFe₂O₄载氧体的生物质化学链气化反应进行了热力学分析,研究了载氧体添加量、温度及水蒸气含量对气化反应特性的影响。同时应用热重分析仪对CoFe₂O₄和生物质的气化反应特性进行了实验研究,并利用XRD对反应前后载氧体的物相组成进行分析。热力学研究表明,CoFe₂O₄在气化反应中能够提供晶格氧,有效促进生物质气化,提高碳转化率。随着反应温度升高,合成气中H₂和CO的含量增加,CO₂的含量减少。随着水蒸气含量增加,H₂和CO₂含量会增加,CO含量减少。添加水蒸气能够提高合成气中H₂和CO的比值,改善合成气的品质。热重实验及XRD结果表明,钴优先于铁被还原,钴与铁存在协同作用,钴能够促进铁的进一步还原。随着载氧体添加量的增加,载氧体被还原的程度会降低,载氧体与生物质的最佳质量比为0.8。     

铁体系催化丁二烯聚合

首先研究了三氯化铁与含氮配位体之间的络合反应: FeCl₃→LFeCl₃·L用穆斯堡尔谱研究了Fe(phen)Cl₃与(i-C₄H₉)₃Al的反应,结果表明,(i-C₄H₉)₃Al不仅可以和铁的络合物发生烷基化反应,而且可以使Fe(Ⅲ)还原为Fe(Ⅱ)。     

Fe改性Zr基蒙脱土对新疆和丰煤热解行为的影响

采用机械球磨法制备不同Fe盐改性Zr基蒙脱土催化剂,通过X射线衍射仪（XRD）、物理吸附仪（BET）、化学吸附仪（NH3-TPD、H₂-TPR）和X射线光电子能谱仪（XPS）分析其组成和结构。结果表明,与24ZrAM相比,以FeCl₃·6H₂O和FeCl₂·4H₂O为铁源时,3Cl^--24ZrAM和2Cl^--24ZrAM中生成了Fe–O–Zr结构。Fe的硫酸盐存在时,催化剂的比表面积显著减小。引入Fe后,催化剂的总酸量均降低,3Cl^--24ZrAM的酸量与强酸强度最高。H₂-TPR显示,3Cl^--24ZrAM、2Cl^--24ZrAM和3NO3--24ZrAM中Fe₂O₃还原为Fe₃O₄的温度均低于500℃。在固定床反应器中考察了催化剂对新疆和丰煤热解行为及含不同...     

1-己基-3-甲基咪唑四氯化铁盐固化环氧树脂E-51的反应特性

采用差示扫描(DSC)量热分析法研究了1-己基-3-甲基咪唑四氯化铁离子液体([C₆mim]FeCl₄)与双酚A型环氧树脂E-51的固化反应。结果显示,由于[C₆mim]FeCl₄包含多级胺基结构,因此可以作为E-51的高温固化剂使用,其与E-51的反应包含两个阶段:第一个阶段的反应放热峰峰顶温度约在120 ℃,第二个阶段的反应放热峰峰顶温度会随着[C₆mim]FeCl₄用量的增加而发生变化。当[C₆mim]FeCl₄与混合胺复配成新型固化剂时,二者产生明显的协同效应。通过恒温DSC实验发现,复配体系与E-51的固化反应可以在室温下发生,表现为在30 ℃固化反应放热峰峰顶放热时间为5 min左右,且随着恒温固化反应温度的提高,峰顶放热峰时间会缩短。非等温动力学结果显示:复配体系与E-51的反应活化能为979 J/mol,仅是混合胺体系的17%左右。反应级数为0.5表明这一固化反应是无规反应。     

含不同取代基的钌-锗化合物的合成及表征（英文）

钌-锗化合物(PPh₃)(X)RuGeCl₂Ar Trip (X=H,1;Cl,2;Ar Trip=C₆H₃-2-(η⁶-Trip)-6-Trip,Trip=2,4,6-ⁱPr₃-C₆H₃)与有机试剂如格氏试剂、LiHBEt₃以及萘钠反应实现了锗和钌原子上的取代基团的调控.化合物1与格氏试剂EtMgBr在不同的温度下反应,分别生成(PPh₃)HRu Ge Br₂ArTrip (3)和(PPh₃)HRuGeEt₂ArTrip (4).化合物1和LiHBEt₃反应也生成化合物4,在该反应中LiHBEt₃作为乙基转移试剂而不是氢化试剂.此外,化合物1与HBF₄反应生成离子型化合物[(PPh₃)H     

借助手持技术探究外界条件对三价铁离子催化过氧化氢分解的影响*

针对FeCl₃溶液催化分解 H₂O₂实验中出现的异常现象,借助手持技术并运用控制变量方法分别探究了反应物及催化剂浓度、溶液pH、Cl^-效应等因素对Fe³⁺催化H₂O₂分解速率的影响,探寻FeCl₃溶液催化分解 H₂O₂溶液的最佳实验条件。     

准东煤灰渣烧结熔融过程中钠基化合物作用机理研究

将Na₂CO₃添加剂按折算为Na₂O以20%的比例掺入煤灰中制成混合灰样,对混合灰样在不同温度下烧结.对不同温度下的烧结灰进行EDS元素分析和XRD物相分析,探究钠基化合物在准东煤灰烧结过程中的转变机理.并以EDS分析结果为基础用Fact sage 5.2计算软件中的Equilib模块进行化学热力学平衡反应计算.结果表明,随着烧结温度的升高,硫会发生富集,而钠主要和硫反应生成Na₂SO₄.同时会有NaCl的产生,NaCl会与含钾化合物反应置换出KCl.NaCl、KCl和Na₂SO₄与其他物质产生低温共熔物.     

煤催化气化条件下不同煤种煤灰烧结行为研究

选取9类典型煤种,利用压差法测定烧结温度的实验装置,结合灰渣的XRD分析结果,考察了添加K基碱金属催化剂、不同煤种灰成分对烧结温度的影响。结果表明,碳酸钾催化剂的添加,明显降低高铁钙含量的WJT煤的灰熔点及烧结温度,碱金属K化合物极易同煤中Fe、Ca的矿物质反应生成低温共融物进而加剧煤灰的熔融结渣。不同煤种烧结温度的差异与煤灰中硅、铝、铁、钙含量密切相关。铝、硅含量高的煤灰烧结温度较高,而铁、钙含量高的煤灰烧结温度相对较低。碱金属K催化剂的添加加剧了煤灰的烧结结渣,而钙、铁的存在会加速硅铝酸盐间的反应生成低温共融物进而加速灰熔融。各煤种烧结温度的变化与其灰成分在CaO-SiO₂-Al₂O₃、FeO-SiO₂-Al₂O₃三元相图上的位置相吻合。     

玉米秸秆与塑料PE共气化过程中碱金属迁移行为的研究

选取一定混合比例的玉米秸秆与塑料PE制成混合燃料,采用固定床实验台,通过改变反应温度,并结合化学热力学平衡分析、X射线衍射及扫描电子显微电镜能谱分析技术对共气化过程中碱金属的迁移行为进行研究。结果表明,气化气中碱金属以气态组元KCl、K₂Cl₂、NaCl形式存在。混合燃料中掺入塑料PE后,C、H含量增加,H使得共气化反应中更容易与Cl反应生成HCl,而非KCl,同时C更容易与K结合,导致K的释放率低于单独玉米秸秆气化,但使Na释放率增加。灰中碱金属化合物以KCl、NaCl、K₂SO₄、KAlSi₃O₈、KAlSiO₄、NaAlSi₃O₈、NaAlSiO₄为主,气化温度高于800℃后灰中K、Na、Cl更易沉积于微孔边缘。     

O2/CO2燃烧气氛对混煤灰中矿物质间反应影响研究

对蒙煤与平七煤两种单煤及其按照不同比例组成的混煤,分别在O₂/CO₂和O₂/N₂气氛下,采用管式炉燃烧制取灰样;对灰样进行灰熔点、XRD及同步热分析（TG/DSC）测试,并进行相关热力学计算,分析了O₂/CO₂燃烧方式对混煤灰中矿物质间反应的影响。结果表明,常规灰熔点测试方法测得的两种气氛下的混煤灰熔点没有明显差别。O₂/CO₂气氛促进了煤灰/混煤灰中钙的碳酸化,且明显抑制了高温下CaCO₃的分解。气氛的改变影响了含钙矿物的转化,进而影响了混煤中钙与莫来石反应生成低温共熔物;O₂/CO₂气氛下钙更易于与莫来石发生反应生成低温共熔物,从而会增加结渣倾向。当混煤中蒙煤比例达到或大于75%时,随着蒙煤比例的逐渐增加,莫来石含量减少,O₂/CO₂气氛对钙与莫来石之间的反应影响减弱,但对含铁矿物的影响更加明显,使其更易于生成含铁玻璃体,从而也会增加结渣倾向。     

Chemometric and trend analysis of water quality of the South Chennai lakes: an integrated environmental study

In order to bring out the nature of the factors influencing lake water composition, multivariate statistical analysis and trend analysis were performed based on the hydrochemical data of the study area, namely, South Chennai. Change in land use pattern and settlements along the banks of the lakes alters the quality and quantity of the surface water. In the present study, the R‐mode factor analysis and cluster analysis were applied to the geochemical parameters of the water to identify the factors affecting the chemical composition of the lake water. Dendograms of both the seasons give three major clusters, reflecting the groups of unpolluted to moderately polluted, polluted, and heavily polluted stations. The movement of stations from one cluster to another clearly brings out the seasonal variation in the chemical composition of the lake water. The complex hydrochemical data of the surface water were interpreted by condensing them into three major factors. Factor score analysis was used successfully to delineate the stations under study and the role of the contributing factors, and the nature of factors responsible for the variation in chemical composition of the water has been clearly brought out. Results of trend analysis using ArcGIS clearly indicate that the trend in water quality is deteriorating at a faster rate in the eastern part of the study area. It is understood that although natural shifts probably can account for some of the variation, it is most likely that human activities play a major role in affecting the water quality on a regional scale. Copyright © 2014 John Wiley & Sons, Ltd.     

Impact of alkali treatment on physico-chemical,thermal, structural and tensile properties of Carica papaya bark fibers

This study aims to examine the effect of sodium hydroxide (NaOH) treatment on the physico-chemical properties, structure, thermal, tensile and surface topography of Carica papaya fibers (CPFs). The surface of raw CPFs was modified by soaking with 5% NaOH solution for 15, 30, 45, 60, 75 and 90?min. The results of thermo-gravimetric analysis revealed that the optimum treatment time for alkali treatment was 60?min. It was found that the alkali treatment improved the properties of the CPFs. The results of TGA, FT-IR, XRD and AFM suggest that the treated CPF is a suitable alternative as reinforcement in polymer composites.     

On-line fermentation gas analysis: Error analysis and application of mass spectrometry

On-line fermentation gas analysis is of general interest because it permits the determination of metabolic rates in almost any biological process using living organisms. The consumption and production of gases (O₂, CO₂, CH₄, etc.) and volatile compounds may be determined without causing any risk of infection. Elemental balancing permits the determination of other metabolic rates if the stoichiometry is known. This was studied with the production of poly-β-hydroxybutyrate (PHB) by Alcaligenes latus. Estimations were based on the measurement of gas partial pressure and flow-rates, pH and alkali consumption rate. Experiments with a small quadrupole mass spectrometer showed unacceptable error propagation. Therefore, dynamic error propagation for all rates was studied using simulation. It was found that, for example, a 1% relative offset-calibration error for oxygen can result in an error in PHB estimation of > 50%. It is suggested that this culture is used in combination with elemental balancing for thorough tests of the accuracy of on-line gas analysis equipment. An on-line process gas analyser based on a quadrupole mass spectrometer (Balzers PGM 407) gave the following precision values (abs. vol.?%) during cultivation of Bacillus subtilis: nitrogen (m/z 14), 0.024; oxygen (m/z 32), 0.020; argon (m/z 40), 0.0011; and carbon dioxide (m/z 44), 0.0034. These values, combined with automatic recalibration, would be sufficient for reasonable estimation of PHB, biomass and substrates.     

新材料的发展与分析化学

文章介绍了新材料的重要性及发展方向,分析化学在新材料研制中起着耳目的作用,另一方面新材料也为分析化学的进展提供了课题与条件。微量分析、微区分析、表面分析是此领域中的重点。在未来的发展中,分析化学在材料的发展中的地位不会改变,并期待着分析灵敏度与空间分辩率的进一步提高。     

Determination of rank by augmentation (DRAUG)

Determining the rank of a chemical matrix is the first step in many multivariate, chemometric studies. Rank is defined as the minimum number of linearly independent factors after deletion of factors that contribute to random, nonlinear, uncorrelated errors. Adding a matrix of rank 1 to a data matrix not only increases the rank by one unit but also perturbs the primary factor axes, having little effect on the secondary axes associated with the random errors in the measurements. The primary rank of a data matrix can be determined by comparing the residual variances obtained from principal component analysis (PCA) of the original data matrix to those obtained from an augmented matrix. The ratio of the residual variances between adjacent factor levels represents a Fisher ratio that can be used to distinguish the primary factors (chemical as well as instrumental factors) from the secondary factors (experimental errors). The results gleaned from model studies as well as those from experimental studies are used to illustrate the efficacy of the proposed methodology. The method is independent of the nature of the error distribution. Limitations and precautions are discussed. An algorithm, written in MATLAB format, is included. Copyright © 2011 John Wiley & Sons, Ltd.     

用局部拟合主成分回归计算光度分析法测定黄连生物碱

针对具有样本数据非无匀分布和非线性特点的光度分析问题，提聘种局部拟合 主成分回归法，用于中药多组分计算测定。该方法根据待测样本与各已知样本光度 分析数据的欧式距离确定相应的权值，将部分权值较大的样本组成校正集，并用分 段线性拟合算法建立待测样本的校正预测模型，将其用于分析黄连的药根碱、巴巴 亭和小檗碱等三种生物碱，所得预测均方根误差分别为0.023,0.0400和0.052，优 于主成分回归法、偏最小二乘法以及人工神经元网络法所得结果。这表明，本方法 用于中药光度分析能获得较为准确的计算分析结果。     

双嘧达莫的荧光光谱分析法

以荧光光谱法研究了双嘧达莫在溴化十六烷基三甲基铵(CTMAB)、β_环糊精 (β_CD)、十二烷基硫酸钠 (SDS)等介质体系中的荧光性质 ,发现CTMAB、SDS和 β_CD对双嘧达莫均有不同程度的荧光增敏作用 ,提出了在CTMAB、SDS和 β_CD水溶液中测定双嘧达莫的荧光光谱分析法 ;该法灵敏度高 ,检出限低(3.20×10 -9mol/L) ,在6.40×10 -8～3.20×10 -6mol/L范围内荧光强度与双嘧达莫的浓度呈良好线性关系     

高效液相色谱荧光检测法测定福建乌龙茶中痕量硒

本文研究了2,3-二氨基萘(DAN)与Se(Ⅳ)反应,生成4.5-苯并苤硒脑(NSD),利用环已烷萃取反应生成的络合物。将有机相注射入填充有μ一Bondapak C_(18)固定相的色谱柱,以环已烷-四氢呋喃(90:10)为流动相,流速为1.0 mL/min,进行HPLC一荧光检测。测定了福建乌龙茶中的微量硒。方法的精密度和回收度均好。检测限达0.12 ng。     

Determination of Mercury in Geological Materials by Continuous-Flow,Cold-Vapor,Atomic Absorption Spectrophotometry

Abstract

To determine mercury in geological materials, samples are digested with nitric acid and sodium dichromate in a closed teflon vessel. After bringing to a constant weight, the digest is mixed with air and a sodium chloride-hydroxylamine hydrochloride-sulfuric acid solution and then Hg(II) is reduced to Hg with stannous chloride in a continuous flow manifold. The mercury vapor is then separated and measured using cold vapor atomic absorption spectrophotometry (CV-AAS). For a 100 mg sample the limit of detection is 20 parts per billion (ppb) Hg in sample. To obtain a 1% absorption signal, the described method requires 0.21 ppb Hg solution (equal to 16 ppb in sample). Precision is acceptable at less than 1.2% RSD for a 10 ppb Hg aqueous standard. Accuracy is demonstrated by the results of the analysis of standard reference materials. Several elements do interfere but the effect is minimal because either the digestion procedure does not dissolve them (e.g., Au or Pt) or the; are normally of low abundance (e.g., Se or Te).