Ni2+掺杂Ti/SnO2-Sb2O5电极的制备及性能

采用溶胶凝胶法制备了Ni2+掺杂的Ti/SnO2-Sb2O5电极,并通过XRD、SEM、EDS、苯酚降解、加速寿命实验等技术手段,研究了Ni2+的掺杂对电极的结构、形貌、电催化性能及稳定性的影响。结果表明:Ni2+的掺入细化了SnO2晶粒,增大了电极的比表面积,改善了电极表面的龟裂程度,提高了电极的导电性能;相对于Ti/SnO2-Sb2O5电极Ni2+的掺入将苯酚完全降解的时间缩短为原来的40%,将电极的使用寿命提高为原来的4.8倍。     

不同掺杂元素的钛基PbO2电极对苯酚电催化氧化性能的影响

本文在SnO2-Sb2O5氧化物为中间层的钛基体上,采用电沉积法制备了无掺杂的Ti/PbO2、掺杂F的Ti/PbO2(Ti/PbO2+F)和掺杂Co3O4纳米粒子的Ti/PbO2电极(Ti/PbO2+Nano-Co3O4).用X射线衍射(XRD)和扫描电镜(SEM)分析和观察了电极材料的组成、结构和形貌,并通过电化学方法研究了这三种电极对苯酚的电催化氧化性能.结果表明,Ti/PbO2+F电极的析氧电位较Ti/PbO2电极的发生明显正移,但其苯酚的氧化峰和析氧峰并不能分开;而Ti/PbO2+Nano-Co3O4电极虽然其析氧电位负移,但对苯酚的氧化峰出现在析氧峰之前.这一结果表明,体系存在着某种反应特别快的瞬态中间体,即在水分子被解离之前已与苯酚发生了反应,从而更有利于苯酚的转化和降解.     

Sno2+Sb203中间层的制备条件对Ti/SnO2+Sb2O3/PbO2阳极性能的影响

研究了聚合前驱体制备的SnO2+Sb2O3中间层的焙烧温度、锑含量对Ti/SnO2+Sb2O3/PbO2阳极性能的影响. 用XRD、ESEM和探针法对锡锑中进行了表征,应用阳极寿命快速检测法测定了Ti/SnO2+Sb2O3/PbO2电极在1.0 mol/L H2SO4溶液中的寿命,并用极化曲线和电荷容量表征了锡锑中间层对钛基PbO2阳极性能的影响. 实验结果表明,聚合前驱体制备中间层的焙烧温度和锑含量对Ti/SnO2+Sb2O3/PbO2电极的寿命和性能有显著的影响. 在锡锑中间层的制备温度为500 ℃、n(Sn):n(Sb)=9:1时,制得的Ti/SnO2+Sb2O3/PbO2电极用阳极寿命快速检测法测得的电极寿命达30h,具有良好的稳定性.     

改性Ti/SnO2-Sb电极降解硝基苯废水

采用热分解法制备了Ti/SnO2-Sb电极,并通过掺杂Cu,Ni,La,Ce,Nd,Zn和Bi等金属对该电极进行改性.采用扫描电子显微镜(SEM)及X射线衍射(XRD)等方法表征了电极的形貌及晶型;通过加速电极寿命测试和电催化降解硝基苯模拟废水实验,研究了金属掺杂对Ti/SnO2-Sb电极稳定性及电催化活性的影响.根据硝基苯降解的动力学方程分析不同金属掺杂对电极降解速率的影响;通过质谱对硝基苯的降解机理进行了初步探讨;采用水杨酸捕集羟基自由基的液相色谱法测定OH.的浓度.实验结果表明,与空白Ti/SnO2-Sb电极相比,金属掺杂改善了电极的表面形貌和SnO2衍射峰的强度,提高了Ti/SnO2-Sb阳极的电解寿命.对硝基苯模拟废水的电解实验结果表明,掺杂电极的电催化降解能力显著提高,硝基苯的降解符合准一级反应动力学方程.质谱分析结果表明,硝基苯在阴极被还原成苯胺并被氧化降解成其它有机物的过程发生迅速.羟基自由基浓度测定结果表明,自由基浓度越高,硝基苯降解速率越快,反应60 min时,空白Ti/SnO2-Sb电极的OH·浓度只有掺Cu金属电极的1/5.     

钕改性钛基SnO2/Sb电催化电极的制备及表征

为改善钛基SnO2／Sb电极的电催化性能,采用浸渍法制备了Nd改性钛基SnO2／Sb电极。以活性艳红X-3B为目标有机物,考察电极的电催化性能,对制备温度和Nd掺杂量进行了研究,确定了适宜的制备条件为：热处理温度550℃,Nd掺杂量1.0％。采用SEN,EDS,XRD及XPS等分析方法对所制备电极的表面形貌、元素组成及结构进行分析,发现掺杂Nd可使SnO2粒径变小,有利于电极电催化性能的改善,同时Nd元素的引入可使杂质元素sb,Nd在电极表面涂层富集。Nd改性钛基SnO2／Sb电极表面主要是四方相金红石结构的SnO2晶体,掺杂的sb和Nd分别以Sb^5＋和Nd^3＋的形式存在。电极动电位扫描测试结果表明,Nd改性钛基SnO2／Sb电极具有较高的阳极析氧电位,有利于有机物的阳极氧化降解。     

纳米SnO2/TiO2电极的制备及其电催化降解间-硝基苯酚

用电化学方法在乙二醇溶液中制备锡、钛醇盐配合物Sn0.75Ti(OCH2CH2OH)(7-x),将电解液水解、干燥后在400℃煅烧2 h,得到纳米级SnO2/TiO2粉体。通过红外光谱(FT-IR)和拉曼光谱(Raman)对电解产物进行测试,纳米SnO2/TiO2粉体通过X射线粉末衍射(XRD)和扫描电子显微镜(SEM)进行表征。实验表明,在有机体系电解得到的纳米SnO2/TiO2粉体颗粒分散较理想,粒径在100～200 nm。再通过溶胶-凝胶法在钛丝表面得到纳米SnO2/TiO2电极,采用循环伏安法研究电极在酸性溶液和间-硝基苯酚溶液中的氧化还原行为和电催化活性。结果表明,纳米TiO2掺杂SnO2电极的氧化峰电流达到143×10-3A/cm2,氧化还原峰电位差明显减小,催化降解间-硝基苯酚的COD去除率达到86.1%,具有较高的电催化活性。     

SnO_2 Sb_2O_3中间层的制备条件对Ti/SnO_2 Sb_2O_3/PbO_2阳极性能的影响

研究了聚合前驱体制备的SnO2 Sb2 O3 中间层的焙烧温度、锑含量对Ti/SnO2 Sb2 O3 /PbO2 阳极性能的影响。用XRD、ESEM和探针法对锡锑中间层进行了表征 ,应用阳极寿命快速检测法测定了Ti/SnO2 Sb2 O3 /PbO2 电极在 1 0mol/LH2 SO4溶液中的寿命 ,并用极化曲线和电荷容量表征了锡锑中间层对钛基PbO2 阳极性能的影响。实验结果表明 ,聚合前驱体制备中间层的焙烧温度和锑含量对Ti/SnO2 Sb2 O3 /PbO2 电极的寿命和性能有显著的影响。在锡锑中间层的制备温度为 5 0 0℃、n(Sn)∶n(Sb) =9∶1时 ,制得的Ti/SnO2 Sb2 O3 /PbO2 电极用阳极寿命快速检测法测得的电极寿命达 30h ,具有良好的稳定性     

F-和Fe3+掺杂对Ti基PbO2阳极性能的影响

采用热分解-电镀法制备了Ti基PbO2,阳极(Ti/PbO2),F-掺杂PbO2阳极(Ti/F-PbO2),Fe3+掺杂PbO2阳极(TiP/Fe-PbO2)和F-,Fe3+共掺杂PbO2,阳极(Ti/F-Fe-PbO2).采用XRD和EDX测试对电极进行了表征,应用加速电解寿命测试和电催化降解4-氯苯酚(4-CP)污水,考察了F-掺杂,Fe3+掺杂和F-,Fe3+共掺杂对PbO2阳极稳定性及电催化活性的影响.结果表明,Ti/F-PbO2和Ti/FePbO2阳极有相近的电催化降解活性,但与Fe3+掺杂相比,F-掺杂大大提高了PbO2阳极的加速电解寿命.对Ti/F-Fe-PbO2阳极,Fe3+掺杂改善了其导电性能.同时F-掺杂提高了阳极的稳定性能,使其有较长的电解寿命.与Ti/PbO2,Ti/F-PbO2和Ti/Fe-PbO2阳极相比,Ti/F-Fe-PbO2阳极的电催化降解活性显著提高,这不仅与其导电性能的改善有关,更与F-掺杂和Fe3+掺杂对4-CP降解的表面协同作用有关.     

钛基二氧化锡电极电解过程中羟基自由基检测及电催化机理

采用浸渍-热分解方法制备了钛基二氧化钌(Ti/RuO2)和钛基二氧化锡(Ti/SnO2)两类尺寸稳定阳极电极。以扫描电子显微镜(SEM)和X射线衍射(XRD)对电极结构进行了表征。用循环伏安法(CV)比较研究了Ti/RuO2和Ti/SnO2电极直接电催化氧化苯酚性能,表明苯酚在Ti/RuO2和Ti/SnO2电极上均可发生直接电氧化反应,两种电极上氧化峰电位分别为0.96和1.43 V(vs.Ag/AgC l)。以对苯二甲酸为捕获剂,利用荧光光谱法进行了羟基自由基(.OH)检测。Ti/SnO2电极在电解过程中能够产生.OH;而Ti/RuO2电极.OH的生成极其微弱。Ti/SnO2电极电解过程中生成.OH是其具有高电催化活性的主要原因,也表明了用荧光法进行羟基自由基检测方便、灵敏,可以用于电催化过程羟基自由基的检测。     

对甲基苯酚电催化氧化机理

在无隔膜电解槽中, 利用线性伏安法和恒电流电解法研究了Ti/PbO2电极对于对甲基苯酚氧化的电催化活性, 通过阳极过程中对甲基苯酚及其氧化中间产物的液相色谱测定, 研究了对甲基苯酚电催化氧化降解的机理. 研究结果表明, Ti/PbO2电极能够有效地电催化氧化水溶液中的对甲基苯酚, 在25 ℃下, 初始浓度为2 mmol/L的对甲基苯酚溶液, 恒定电流密度为50 mA/cm2, 电解3 h, 对甲基苯酚的转化率为74.32%, 有机碳去除率为61.81%. 对甲基苯酚电氧化降解要经过生成对羟基苯甲醇、对羟基苯甲醛、对羟基苯甲酸、对苯二酚、对苯醌、顺丁烯二酸和草酸, 最终变成CO2的历程, 其中对苯二酚的氧化和顺丁烯二酸的氧化为反应的速控步骤.     

The preparation of NbH5(Me2PCH2CH2Me2)2 and NbHL2(Me2PCH2CH2PMe2)2 (L = CO or C2H4)

MMe₅(dmpe) (M = Nb or Ta, dmpe = Me₂PCH₂CH₂PMe₂) reacts with H₂ (500 atm) and dmpe in THF at 60°C to give MH₅(dmpe)_2? NbH₅(dmpe)₂ readily reacts with two mol of CO or ethylene (L) to give NbHL₂(dmpe)₂. The exchange of the hydride ligand with the ethylene protons in NbH(C₂H₄)₂(dmpe)₂ is not rapid on the ¹H NMR time scale (60 MHz) at 95°C.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Formation of nano-crystalline quartz crystals from ZnO/MgO/Al2O3/TiO2/ZrO2/SiO2 glasses

Glasses with the compositions 50.9 SiO₂ · 20.8 Al₂O₃ · (20.8 ? x) MgO· × ZnO · 3.7 TiO₂ · 3.7 ZrO₂ with x = 0, 2.3, 4.6 and 9.3 were annealed at temperatures in the range from 850 to 1100 °C. Depending on temperature, high- or low-quartz solid solutions, magnesium aluminosilicate, mullit and spinel precipitated. These glass–ceramics exhibit excellent mechanical properties and are potential candidates for applications in micromechanics or as hard disc substrate.The larger the ZnO concentration, the lower is the glass transition temperature. Also microhardnesses and Young’s moduli increased with increasing ZnO concentration. The nucleation temperature was of minor importance. To achieve good mechanical properties, the initially formed high-quartz phase must transform to the corresponding low-quartz phase. This occurs if the quartz phase contains only minor MgO or ZnO concentrations, which can be achieved by increasing the annealing times or temperature. Then MgO, ZnO and Al₂O₃ occur as separate spinel or gahnite phase.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Removal of NO in NO/N2, NO/N2/O2, NO/CH4/N2, and NO/CH4/O2/N2 systems by flowing microwave discharges

In this paper, continuing previous work, we report on experiments carried out to investigate the removal of NO from simulated flue gas in nonthermal plasmas. The plasma-induced decomposition of small concentrations of NO in N2 used as the carrier gas and O2 and CH4 as minority components has been studied in a surface wave discharge induced with a surfatron launcher. The reaction products and efficiency have been monitored by mass spectrometry as a function of the composition of the mixture. NO is effectively decomposed into N2 and O2 even in the presence of O2, provided always that enough CH4 is also present in the mixture. Other majority products of the plasma reactions under these conditions are NH3, CO, and H2. In the absence of O2, decomposition of NO also occurs, although in that case HCN accompanies the other reaction products as a majority component. The plasma for the different reaction mixtures has been characterized by optical emission spectroscopy. Intermediate excited species of NO*, C*, CN*, NH*, and CH* have been monitored depending on the gas mixture. The type of species detected and their evolution with the gas composition are in agreement with the reaction products detected in each case. The observations by mass spectrometry and optical emission spectroscopy are in agreement with the kinetic reaction models available in literature for simple plasma reactions in simple reaction mixtures.     

Formation of [Cp2TiSbMe2]2, [Cp2TiSb(SiMe3)2]2 and [Cp2TiCl]2·2Mes4Sb2

Reactions of [Cp₂Ti(btmsa)] (btmsa = bis(trimethylsilyl)acetylene) with R₄Sb₂ (R = Me, Me₃Si) give [Cp₂TiSbMe₂]₂ (1) or [Cp₂TiSb(SiMe₃)₂]₂ (2) respectively. [Cp₂TiCl]₂·2Mes₄Sb₂ (3) is serendipitously formed from [Cp₂Ti(btmsa)] and Mes₂SbH containing NH₄Cl traces.     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

Cu-MOF催化过氧化氢应用于多巴胺的检测

本文利用一种具有H_2O_2催化活性的Cu-MOF[Cu_3(BTC)_2(H_2O)_3,简称HKUST-1],构建了以邻苯二胺(OPD)为颜色指示分子的比色传感体系,实现了对H_2O_2和多巴胺(DA)的快速灵敏检测。HKUST-1起到催化H_2O_2氧化OPD的作用,反应体系能够呈现出显著的颜色变化。在优化条件下,415nm处的吸收峰强度与H_2O_2浓度呈双线性关系,线性范围分别为10~50 mmol/L和50~100 mmol/L,相对标准偏差分别为0.9947和0.9995,最低检出限为1.29mmol/L。由于DA能抑制H_2O_2氧化OPD,因此比色传感体系还可以用于快速检测DA,线性范围分别为0.25~5μmol/L和2.5~25μmol/L,相对标准偏差分别为0.9783和0.9705,最低检出限为0.262μmol/L。该项工作拓展了Cu-MOFs材料在生物分子催化和生物传感方面的应用。     

Reaction Mechanisms in Both a CCl2F2/O2/Ar and a CCl2F2/H2/Ar RF Plasma Environment

Decomposition of dichlorodifluoromethane (CCl₂F₂ or CFC-12) in aradiofrequency (RF) plasma system is demonstrated. The CCl₂F₂decomposition fractions _{CCl 2 F 2} and mole fractionsof detected products in the effluent gas stream of CCl₂F₂/O₂/Ar andCCl₂F₂/H₂/Ar plasma, respectively, have been determined. The experimentalparameters including input power wattage, O₂/CCl₂F₂ or H₂/CCl₂F₂ ratio,operational pressure, and CCl₂F₂ feeding concentration wereinvestigated. The main carbonaceous product in the CCl₂F₂/O₂/Arplasma system was CO₂, while that in the CCl₂F₂/H₂/Ar plasma systemwas CH₄ and C₂H₂. Furthermore, the possible reaction pathways werebuilt-up and elucidated in this study. The results of the experimentsshowed that the highly electronegative chlorine and fluorine wouldeasily separate from the CCl₂F₂ molecule and combine with the addedreaction gas. This led to the reactions terminated with the CO₂,CH₄, and C₂H₂ formation, because of their high bonding strength. Theaddition of hydrogen would form a preferential pathway for the HCland HF formations, which were thermodynamically stable diatomicspecies that would limit the production of CCl₃F, CClF₃, CF₄, andCCl₄. In addition, the HCl and HF could be removed by neutral orscrubber method. Hence, a hydrogen-based RF plasma system provideda better alternative to decompose CCl₂F₂.