用于离子迁移率谱仪的快速热解析进样方法

热解析是用于离子迁移率谱仪(IMS)的液体和固体样品进样的重要手段,但在检测高沸点或易分解有机物时,存在易重新凝结或过热分解的问题.本研究建立了一种与IMS半透膜结合的热解析进样方法,设计了可快速加热的微型热解析装置,通过热子通电发热及热电偶测温实现对样品解析区域的升温控制,提高半透膜的进样效率.以低浓度三聚氰胺溶液为...     

搅拌棒吸附萃取-液相色谱-串联质谱法测定微山湖水中的有机磷农药残留

采用搅拌棒吸附萃取结合液相色谱-串联质谱法测定微山湖水中的马拉硫磷、三唑磷、喹硫磷、伏杀硫磷等4种有机磷农药残留。对影响有机磷农药残留吸附萃取效率的萃取涂层、样品溶液的酸度、振荡速率、萃取时间、溶液的离子强度、解吸液、解吸时间和解吸模式等因素进行了优化,确定了最佳吸附萃取条件。样品经搅拌棒萃取、解吸后,采用ZORBAX Eclipse Plus C_(18)色谱柱分离。在多反应监测模式下检测,外标法定量。4种有机磷农药的质量浓度在一定范围内与峰面积呈线性关系,检出限(3S/N)在0.16~0.73μg·kg~(-1)之间。加标回收率在72.3%~107%之间,测定值的相对标准偏差(n=6)在7.8%~11%之间。     

基于固相微萃取-离子迁移率谱的敌敌畏快速检测方法

针对水体中痕量有机磷农药检测的需要,搭建了电晕放电离化离子迁移率谱仪。以固相微萃取作为样品前处理方法,借助于全新设计的进样装置,利用高温工作漂移管对萃取涂层中待测样品进行解吸,在载气的辅助下将样品直接引入离化区放电针尖附近,提高了水体中敌敌畏检测的灵敏度及稳定性。在优化的检测条件下,当萃取时间为5 min时,敌敌畏标准品理论检出限为0.16μg/kg(3倍信噪比),线性范围为1~250μg/kg,相关系数为0.9996,相对标准偏差小于10%。对湖水样品进行检测,敌敌畏加标回收率为91%~96%。     

基于微热板表面离子化源的离子迁移率谱仪研究

根据表面离化机理和离子迁移率谱检测方式,设计和制备了一种基于表面离化源的离子迁移率谱仪(IMS)。表面离化源为采用微机电系统(MEMS)工艺加工的微热板阵列,除了作为离子产生器,还作为漂移管的一个离子栅,用以实现离子向漂移区的注入。测试了该IMS对三乙胺的响应特性并研究了离子注入时间对离子迁移率谱的影响。结果表明,基于微热板表面离化源的离子迁移率谱仪对三乙胺具有很好的动态响应特性,三乙胺浓度的平方根与离子峰面积具有较好的线性关系,检出限可达6×10-8(V/V)。此外,与传统的放射离化IMS相比,这种IMS还具有离子注入时间短和离子迁移率谱基电流为零等特点。     

重金属离子富集检测的微量热研究

采用微量热技术对重金属离子的富集检测过程进行了研究. 采用流动注射分析法研究了重金属离子进样顺序、 样品进样流速和载体树脂颗粒粒径对重金属离子抑制脲酶催化反应的影响, 优化了脲酶及重金属离子进样量, 获得了脲酶固定化及重金属离子富集条件的优化参数. 结果表明, 在低流速(0.1 mL/min), 载体树脂颗粒粒径为0.5～0.6 mm, 脲酶进样量为3 mL, 重金属离子进样量为5 mL的条件下, 先进行重金属离子的富集, 再检测其对固定化脲酶催化反应的影响可得到较好的检测效果. 在实验浓度范围内, 4种重金属离子对脲酶催化反应的影响顺序为砷离子>铜离子>镉离子>铅离子. 本文对重金属离子进行了适当的富集, 降低其检测下限, 为采用微量热法进行重金属离子的快速检测提供了理论依据.     

固相萃取–气相色谱法测定饮用水中5种有机磷农药

建立了固相萃取–气相色谱法测定饮用水中敌敌畏、乐果、甲基对硫磷、马拉硫磷及对硫磷的方法。采用Cleanert PEP–SPE固相萃取柱,以二氯甲烷、乙酸乙酯、甲醇及纯水活化固相萃取柱,以5 m L/min流量富集水样,然后用二氯甲烷及乙酸乙酯洗脱浓缩后进行气相色谱分析。5种有机磷农药线性相关系数均大于0.995,方法测定下限为0.16~0.80μg/L,加标回收率为59.8%~109.0%,测定结果的相对标准偏差小于16%(n=6)。该方法灵敏度高,准确度好,适用于饮用水中5种有机磷农药的检测。     

固相微萃取/二氧化锡气体传感器联用技术对果蔬中有机磷农药残留的快速检测

研究了固相微萃取(SPME)和二氧化锡气体传感器的联用技术对果蔬中有机磷农药残留乐果、氧乐果、甲胺磷、乙酰甲胺磷、马拉硫磷、敌百虫等的快速检测。结果表明，在85℃下，解吸8min，二氧化锡气体传感器在2min内完成对有机磷农药残留的快速检测。零解吸时间测量的甲胺磷的动态响应曲线表明。SPME／二氧化锡气体传感器联用技术对分析SPME的解吸平衡非常有利。     

马拉硫磷分子印迹聚合物的制备及其在固相萃取中的应用

以马拉硫磷为模板分子,采用原位逐步聚合法制备了具有良好识别性能的分子印迹聚合物(MIPs),考察了马拉硫磷、甲基对硫磷、对硫磷及甲胺磷在马拉硫磷聚合物的选择性分离富集特性。用聚合物固相萃取了蜂蜜、蔬菜和天然水中的马拉硫磷。结果表明,聚合物对模板分子产生了印迹效应,对马拉硫磷有明显的选择性。流速为1.0 mL/min,进...     

离子色谱法测定水中的高氯酸盐

采用离子色谱法测定了饮用水中痕量的高氯酸盐,以30mmol／LNaOH为淋洗液,1mL／min流量,1000μL进样,在25min内可完成测定高氯酸盐;利用加热浓缩的方法对水样进行前处理,浓缩10倍后进样。结果表明,该法回收率为87．9％,检测限为0．10μg/L,具有实际应用价值。     

离子迁移谱法检测圣女果中的敌敌畏和马拉硫磷

建立了采用便携式离子迁移谱仪(IMS)对敌敌畏和马拉硫磷进行快速检测的分析方法.在大气压条件下,以63Ni作为电离源,干燥洁净的空气作为载气和迁移气,采用负离子模式进行操作,气路采用闭路循环模式.在优化条件下(进样口温度为180 ℃,迁移管温度为150 ℃,载气流量和迁移气流量均为0.6L/min)进行检测,敌敌畏和马...     

Confinement of polyaniline chains in capillary layers: an ordering effect of the uniaxially aligned surfaces

An ordering effect of uniaxially aligned poly(tetrafluoroethylene) (PTFE) substrates prepared by rubbing on polyaniline (PANI) molecules at the interfaces of PTFE/PANI film and PTFE/PANI solution has been investigated using electronic absorption spectroscopy. It was observed slight dichroism in electronic spectra from only very thin (thickness approximately 20 nm and less) PANI films as well as from PANI solutions of capillary thickness (10 to 30 microm) confined by oriented PTFE surfaces. The ordering effect is discussed in terms of a hydrodynamic flow arising upon sample formation and steric factors at the PTFE surface, which cause uniaxial deformation of the polymer coil on the rubbed PTFE surface.     

Surface Modification of Poly(tetrafluoroethylene) Films by Plasma Pre-Activation and Plasma Polymerization of Glycidyl Methacrylate

Surface modification of poly(tetrafuoroethylene) (PTFE) film by plasma polymerzation and deposition of glycidyl methacrylate (GMA), in the presence and absence of Ar or O₂ plasma pre-activation, was carried out to enhance the adhesion with polyimides (PI) film in the presence of an epoxy adhesive. For deposition carried out at low RF power, a high epoxide concentration was preserved in the plasma-polymerized GMA (pp-GMA) layer on PTFE (pp-GMA-PTFE). However, high adhesion strength of the PI/pp-GMA-PTFE laminate was obtained only in the presence of O₂ plasma pre-activation of the PTFE substrates prior to plasma polymerization and deposition of GMA. In the absence of any plasma pre-activation or in the presence of Ar plasma pre-activation, the deposited pp-GMA layer on the PTFE surface could be readily removed by solvent extraction. The adhesion enhancement of the PI/pp-GMA-PTFE laminates in the presence of O₂ plasma pre-activation was attributed to the preservation of the epoxide functional groups in the pp-GMA layer, the curing of the GMA chains into the matrix of the epoxy adhesive, and the covalent bonding of the pp-GMA layer on the PTFE surface.     

丙烯酸水溶液聚合法制备PTFE/PAA/Nafion膜及其性能

采用廉价的多孔聚四氟乙烯(PTFE)膜作为基底, 用少量的Nafion与PTFE膜复合可制备低成本的质子膜. 但疏水性的PTFE膜与亲水性的Nafion膜结合性不佳. 基于此, 本文对疏水性的PTFE膜材料表面进行设计, 先采用丙烯酸对疏水性的PTFE膜表面进行亲水性改性, 再喷涂亲水性Nafion膜, 完成低成本PTFE/PAA/Nafion膜的制备. 实验结果表明, 改性前的PTFE膜材料水接触角为150°, 改性后的膜接触角变为55.6°, 亲水性大幅上升, 膜的机械强度和尺寸稳定性(断裂强度为25.2 MPa, 80 ℃下的溶胀率为11.9%)均优于Nafion117膜, 而 Nafion用量则节省了60%. PTFE/PAA/Nafion膜具有高质子导通率(80 ℃下达到131.9 mS/cm), 接近于Nafion117膜, 最大功率密度可以达到404.2 mW/cm².     

聚四氟乙烯膜分离技术在含油废水处理中的应用进展

世界生态环境逐渐恶化,为保护生态环境,含油废水的无害化处理排放成为保护生态环境的必要做法。膜处理技术作为20世纪最具发展前景的污水处理技术之一,具备低能耗,分离效率高等特点。聚四氟乙烯薄膜（PTFE）膜由于其具有的极高化学稳定性、良好的力学性能、过滤速度高、使用寿命长等特点,被广泛应用于水处理领域。为此本文概述膜分离原理,结合膜本身特点和改性方法,重点对PTFE膜及其改性膜在含油废水中的应用进行综述,并探讨了PTFE膜在应用过程中亟待解决的问题,为PTFE膜及其改性膜在水处理中的应用提供技术和理论支持。     

Polarized electroluminescence of a discotic mesogenic compound

Polarized electroluminescence is observed for a uniaxially aligned sample of a discotic compound in its crystalline state. The alignment was achieved by coating the ITO anode with an aligned film of poly(tetrafluoroethylene) (PTFE) deposited using the friction method. Organic light emitting devices with the layer sequence glass/ITO/PTFE/tetraethyl perylene-3,4,9,10-tetracarboxylate (55 nm)/aluminium (100 nm) show linearly polarized emission of light with a dichroic ratio up to 3.2.     

利用聚四氟乙烯为化学改进剂降低电热原子吸收测定铬的基体干扰

本文研究了电热原子吸收光谱测定痕量铬时几种常见的金属离子的干扰作用。     

基于色相算法的表面等离子体共振成像传感器对苯并芘的敏感特性

报道了一种用于原位探测水中苯并芘的彩色表面等离子体共振成像(SPRI)传感器,该传感器既能提供直观的图像信息,又能借助色相算法定量分析待测物质的浓度及其吸附/脱附过程。首先利用自制的波长-图像同步检测型SPR传感器测试了裸金薄膜芯片在不同入射角下的共振波长和共振图像,然后利用色相算法建立了SPR共振波长与图像色相的依赖关系,基于该依赖关系获得了SPR传感器最佳色相灵敏度对应的起始共振波长约为650 nm;另一方面,制备了聚四氟乙烯涂覆的SPR传感芯片,基于聚四氟乙烯膜对水中苯并芘的可逆富集作用实现了苯并芘的原位快速探测。实验取得以下4个结果:(1)在20-100 nmol?L-1浓度范围内彩色SPR图像的平均色相值随着苯并芘浓度的升高线性减小;(2)对100 nmol?L-1的苯并芘的响应和恢复时间分别约为7和5 s;(3)由于聚四氟乙烯膜的厚度大于SPR消逝场穿透深度,检测结果不受溶液折射率影响;(4)在聚四氟乙烯敏感膜厚度较小且不均匀的情况下,传感器容许获取敏感膜的不同厚度区域对苯并芘的色相灵敏度。实验结果有力地证明了这种彩色SPR图像传感器在生化物质检测中具有良好的应用前景。     

Electroless Deposition of Copper on Poly(tetrafluoroethylene) Films Modified by Plasma-Induced Surface Grafting of Poly(4-vinylpyridine)

Argon plasma-pretreated poly(tetrafluoroethylene) (PTFE) films were solution coated with a thin layer of poly(4-vinyl pyridine) (P4VP). Subsequent exposure of the films to argon plasma resulted in the grafting of P4VP on the PTFE films. Electroless plating of copper could be carried out effectively on the P4VP-grafted PTFE (P4VP-g-PTFE) surface after PdCl₂ activation and in the absence of SnCl₂ sensitization (the Sn-free process). The catalytic processes of the electroless plating of copper in the presence and absence of sensitization by SnCl₂ were also compared. The effect of glow discharge conditions on the P4VP concentration and the adhesion strength of the electrolessly deposited copper was investigated. The T-peel adhesion strength of the electrolessly deposited copper with the graft-modified PTFE film was improved in the absence of SnCl₂ sensitization and could reach about 3 N/cm. PdCl₂ activation and electroless deposition of copper could not be carried out on the pristine or the Ar plasma-treated PTFE surface in the absence of prior sensitization by SnCl₂. X-ray photoelectron spectroscopic (XPS) analysis revealed that the electrolessly deposited copper delaminated from the P4VP-g-PTFE film by cohesive failure inside the PTFE film.     

Synthesis and surface properties of a fluorinated polyether

A new polyether consisting of alternate fluorinated/non-fluorinated phenylene units in the backbone has been synthesized via polycondensation of an AB monomer. At room temperature, the polymer film exhibits a low surface energy that is comparable to poly(tetrafluoroethylene) (PTFE). However, as the temperature is raised above a particular level, the surface energy of the polymer films starts to increase. Morphological measurements suggest that a smooth thin polymer film can be formed by solvent casting, but it spontaneously dewets the substrate surface when thermally annealed.     

Polytetrafluoroethylene Sputtered PES Membranes for Membrane Distillation: Influence of RF Magnetron Sputtering Conditions

Thin films of fluorocarbon were deposited on polyethersulfone membranes via argon plasma sputtering of a poly(tetrafluoroethylene) (PTFE) target in an RF magnetron plasma reactor. The obtained deposited ultrathin coatings had nanoscale roughnesses and high degrees of fluorination. The intensity of fluorine atom in plasma environment during fluorocarbon deposition was investigated. Depending on the deposition conditions comprising working gas pressure, applied RF power, and distance between the target and the substrate, polymeric films with different chemical compositions and/or morphologies were obtained. The morphologies of the films were analyzed by means of SEM, XPS, and AFM. The results suggested that the sputtered film deposited at a higher pressure and longer target–substrate distance and moderate RF power had a surface composition and chemical structure closer to those of the PTFE film. The treated hydrophobic PES membranes with water contact angles as high as 115° were applied for the first time in an air gap membrane distillation setup for removal of benzene as a volatile organic compound from water. The results showed that the plasma-treated membranes have a comparable or superior performance to that of commercial PTFE used in membrane distillation with similar permeate flux and separation factor after 20 h long term performance.