一种可分散性石墨烯的制备

先通过γ-氨丙基三乙氧基硅烷(KH-550)与氧化石墨反应得到改性氧化石墨, 再经水合肼还原制备了改性石墨烯. 未烘干的改性石墨烯经超声处理后, 可稳定分散于体积比为9∶1的N,N-二甲基甲酰胺/水或丙酮/水的混合溶液中, 而且在N,N-二甲基甲酰胺/水体系中超声得到的改性石墨烯分散液可在乙醇、丙酮中稳定存在. 采用红外光谱、X光电子能谱及X射线衍射分析等手段研究了KH-550改性氧化石墨及石墨烯的结构. 结果表明, KH-550上的氨基与氧化石墨的羧基反应生成了酰胺键, 与环氧基发生了加成反应, 干燥的改性石墨烯层间通过Si-O-Si键连接在一起.     

石墨烯/银复合薄膜的制备及表征

采用静电自组装技术,通过交替沉积聚(二烯丙基二甲基氯化铵)(PDDA)(或硝酸银)和氧化石墨烯,制备氧化石墨烯/PDDA薄膜和氧化石墨烯/硝酸银复合薄膜。然后在600℃下通入氩气和氢气进行气氛还原得到石墨烯薄膜和石墨烯/银复合薄膜。采用AFM、SEM、XPS、UV-Vis以及四探针电阻仪等对薄膜结构及性质进行表征。结果表明,通过静电自组装法可以获得生长均匀的薄膜。对比于相同自组装次数的石墨烯薄膜,石墨烯/银复合薄膜具有更好的透光性和更低的薄膜方块电阻。在λ=500 nm时,四层石墨烯/银复合薄膜的透过率为85%左右,而石墨烯薄膜的透过率为72%左右;石墨烯薄膜的方阻为161.39 kΩ.□-1,而石墨烯/银复合薄膜的方阻为99.11 kΩ.□-1。     

KH-570功能化石墨烯的制备与表征

采用Hummers法对天然石墨进行氧化处理制备了氧化石墨烯,通过γ-甲基丙烯酰氧丙基三甲氧基硅烷与氧化石墨烯反应得到功能化氧化石墨烯,然后在水合肼的作用下制备了功能化石墨烯。未烘干的功能化石墨烯在超声处理下,能稳定分散在体积比为9∶1(V/V)的乙醇/水、丙酮/水或N,N-二甲基甲酰胺/水的混合溶剂中。用傅立叶变换红外光谱、原子力显微镜、X射线光电子能谱及X射线衍射对样品结构、形貌进行了分析。结果表明,KH-570上的硅氧烷与氧化石墨烯上的羟基发生了反应,经水合肼还原后,功能化石墨烯的无序度增加,层间距也比功能化氧化石墨烯的缩小了。功能化石墨烯在DMF/水中呈高度剥离状态,片层厚度为1.1～2.3 nm。     

4-二苯胺基苯甲醇功能化石墨烯的制备、电子传递及光催化性能

在碱性条件下由氧化石墨(GO)还原获得还原石墨烯(RGO). RGO与4-二苯胺基苯甲醇(TPACH₂OH)混合后发生相互作用, 得到功能化石墨烯复合物(TPACH₂OH-RGO). 采用密度泛函理论(DFT)对TPACH₂OH-RGO模拟计算结果表明, TPACH₂OH和RGO之间主要通过氢键作用形成复合物. 利用紫外-可见光谱(UV-vis)、拉曼光谱(Raman)、荧光光谱(Fluorescence)、原子力显微镜(AFM)、透射电子显微镜(TEM)和电化学等方法研究了TPACH₂OH-RGO结构和光电性质, 并研究了以TPACH₂OH-RGO为催化剂在光照射下光催化分解水制氢性能. 实验结果表明: 光照下复合物中激发态TPACH₂OH向RGO转移电子. 在TPACH₂OH和RGO的质量比为4/3, 体系pH＝6条件下, 光照6 h, TPACH₂OH-RGO的产氢总量达到35.0 μmol, 比RGO的产氢总量(20.4 mmol)有明显的提高.     

The Route to Functional Graphene Oxide

We report on an easy‐to‐use, successful, and reproducible route to synthesize functionalized graphite oxide (GO) and its conversion to graphene‐like materials through chemical or thermal reduction of GO. Graphite oxide containing hydroxyl, epoxy, carbonyl, and carboxyl groups loses mainly hydroxyl and epoxy groups during reduction, whereas carboxyl species remain untouched. The interaction of functionalized graphene with fluorescent methylene blue (MB) is investigated and compared to graphite, fully oxidized GO, as well as thermally and chemically reduced GO. Optical absorption and emission spectra of the composites indicate a clear preference for MB interaction with the GO derivatives containing a large number of functional groups (GO and chemically reduced GO), whereas graphite and thermally reduced GO only incorporate a few MB molecules. These findings are consistent with thermogravimetric, X‐ray photoelectron spectroscopic, and Raman data recorded at every stage of preparation. The optical data also indicate concentration‐dependent aggregation of MB on the GO surface leading to stable MB dimers and trimers. The MB dimers are responsible for fluorescence quenching, which can be controlled by varying the pH value.     

功能化石墨烯材料：定义、分类及制备策略

自2004年被成功制备后,石墨烯因其独特迷人的性质在近十几年来备受关注,同时也引发了二维纳米材料的研究热潮。单原子层厚度的二维结构赋予石墨烯非同寻常的光学、电子学、磁学及力学等性质,使得石墨烯在生物学、医学、化学、物理学和环境科学等多个领域展现出极大的应用潜力。制得注意的是,石墨烯在应用时通常需要进行功能化,调节其组成、大小、形状和结构等,以便于加工处理或满足不同的应用需求。石墨烯功能化方法多样,功能化产物也是种类繁多。然而,到目前为止,石墨烯功能化产物并没有系统全面的分类和精确的定义。因此,本文在系统总结现有石墨烯功能化研究的基础上,给出了石墨烯功能化产物的系统分类、各类的精确定义和相应的制备策略,并通过典型示例进行了详细地阐述。石墨烯功能化的产物统称为“功能化石墨烯材料”,分为两类：“功能化石墨烯”和“功能化石墨烯复合材料”。功能化石墨烯材料的制备可由“自上而下”和“自下而上”两种策略实现。制备策略的选择取决于应用需求。系统分类、精确命名和制备策略的归纳必将有助于功能化石墨烯材料的进一步发展。     

Understanding Self-assembly,Colloidal Behavior and Rheological Properties of Graphene Derivatives for High-performance Supercapacitor Fabrication

Graphene derivatives, such as graphene oxide(GO) and reduced graphene oxide(RGO), have been widely used as promising twodimensional nanoscale building blocks due to their fascinating properties, cost-effective production, and good processability. Understanding the intrinsic self-assembling, colloidal, and rheological features of graphene derivatives is of critical importance to establish the formation-structureproperty relationship of graphene-based materials. This article reviews recent progresses in our studies of these interesting properties of graphene derivatives for developing high performance supercapacitors. The content is organized to include characteristics of the dispersions of graphene derivatives, self-assembly of nanosheets from liquid medium, colloidal behavior, rheological properties of the dispersions, processing methods based on the properties, and performance of the fabricated supercapacitors. GO and RGO nanosheets are proved to form different types of assembled structures with unique morphologies, such as ultrathin layer-by-layer films, porous aggregates, and nanoscrolls. The unique rheological properties of GO dispersions and hydrogels, feasible for both the traditional wet-processing and newly-developed technology like three-dimensional printing, are highlighted for their potential in structural manipulation and scalable fabrication of graphene-based devices. The research devoted to up-grading the performance of supercapacitors is presented in some details, which could be applicable for fabricating other graphene-based energy storage devices. Some challenges and perspectives in our point of view are given in the last part of this feature article.     

功能型单层石墨烯的热剥离法制备及其超电容性能

以氧化石墨(GO)作为前驱体,在两种不同热剥离温度下制备了两类功能型单层石墨烯.其中第一类功能型单层石墨烯通过在较低温度及空气气氛下热剥离GO制备;第二类功能型单层石墨烯通过在氮气保护下高温热剥离GO得到;利用氮气吸附-脱附方法测定了两类样品的比表面积,利用电化学测试方法分析了其超电容性能.结果表明,通过低温热剥离的方式即可以有效剥离GO;两类样品均具有较高的BET比表面积.低温热剥离GO所制备的功能型单层石墨烯在2 mol/L KOH体系中的最大比电容值约为220 F/g;而通过高温热剥离GO所制备的功能型单层石墨烯虽然同样具有较高的BET比表面积,但其最大比电容值下降至约150 F/g.这表明通过低温热剥离GO所制备的功能型单层石墨烯具有更优异的超电容性能.     

A Review on Graphene Oxide Two-dimensional Macromolecules: from Single Molecules to Macro-assembly

Graphene oxide(GO), which consists of two-dimensional(2 D) sp² carbon hexagonal networks and oxygen-contained functional groups, has laid the foundation of mass production and applications of graphene materials. Made by chemical oxidation of graphite, GO is highly dispersible or even solubilized in water and polar organic solvents, which resolves the hard problem of graphene processing and opens a door to wet-processing of graphene. Despite its defects, GO is easy to functionalize, dope, punch holes, cut into pieces, conduct chemical reduction, form lyotropic liquid crystal, and assemble into macroscopic materials with tunable structures and properties as a living building block. GO sheet has been viewed as a single molecule, a particle, as well as a soft polymer material. An overview on GO as a 2 D macromolecule is essential for studying its intrinsic properties and guiding the development of relevant subjects. This review mainly focuses on recent advances of GO sheets, from single macromolecular behavior to macro-assembled graphene material properties. The first part of this review offers a brief introduction to the synthesis of GO molecules. Then the chemical structure and physical properties of GO are presented, as well as its polarity in solvent and rheology behavior. Several key parameters governing the ultimate stability of GO colloidal behavior, including size, p H and the presence of cation in aqueous dispersions, are highlighted. Furthermore, the discovery of GO liquid crystal and functionalization of GO molecules have built solid new foundations of preparing highly ordered, architecture-tunable, macro-assembled graphene materials, including 1 D graphene fibers, 2 D graphene films, and 3 D graphene architectures. The GO-based composites are also viewed and the interactions between these target materials and GO are carefully discussed. Finally, an outlook is provided in this field, where GO is regarded as macromolecules, pointing out the challenges and opportunities that exist in the field. We hope that this review will be beneficial to the understanding of GO in terms of chemical structure,molecular properties, macro-assembly and potential applications, and encourage further development to extend its investigations from basic research to practical applications.     

Functionalization of Graphene Oxide with 3‐Mercaptopropyltrimethoxysilane and Its Electrocatalytic Activity in Aqueous Medium

In this work, a highly dispersed graphene oxide (GO) was successfully functionalized with 3‐mercaptopropyltrimethoxysilane (MPTS) molecule by silanization method. The chemically generated GO and MPTS functionalized GO (MPTS‐GO) were structurally characterized by thermogravimetric analysis (TGA), X‐ray diffraction analysis (XRD), scanning electron microscope (SEM), energy dispersive X‐ray (EDAX), fourier transform infrared spectroscopy (FT‐IR) and ultraviolet visible spectroscopy (UV‐Vis) techniques. The MPTS‐GO is highly suspensable in water. The thermal and conductivity results for MPTS‐GO are significantly increased compared to GO. Moreover, glassy carbon electrode modified with MPTS‐GO hybrid (MPTS‐GO/GCE) was prepared by casting of the MPTS‐GO solution on GCE. The MPTS‐GO/GCE showed an excellent electrocatalytic activity towards methionine (Met). This was understood from the observed less positive oxidation potential and higher oxidation current when compared to bare GC electrode. The MPTS‐GO has excellent electrocatalytic activity, making it an ideal candidate for sensor applications.     

石墨烯的制备、表征及其在透明导电膜中的应用

近年来,石墨烯因其优异的电学和光学等特性,越来越受到人们的广泛关注。研究人员应用多种方法来合成石墨烯并且探讨其潜在的应用价值。本文首先简要介绍了石墨烯的结构及其基本的物理性质,并简单回顾了石墨烯的合成方法和表征手段。在此基础上,讨论了石墨烯/银复合薄膜在透明导电膜中的应用,并详细介绍了我们在该领域的研究成果。用化学气相沉积法（CVD）和多羟基法分别制备了双层石墨烯及银纳米线,成功合成了石墨烯/银复合薄膜,结果表明复合薄膜的方块电阻可降低至26 Ω·□-1,展示了其在光电器件上广泛的应用前景。     

Layer-by-Layer Self-Assembled Multilayer Films Composed of Graphene/Polyaniline Bilayers: High-Energy Electrode Materials for Supercapacitors

Multilayer assemblies of uniform ultrathin film electrodes with good electrical conductivity and very large surface areas were prepared for use as electrochemical capacitors. A layer-by-layer self-assembly approach was employed in an effort to improve the processability of highly conducting polyaniline (PANi) and chemically modified graphene. The electrochemical properties of the multilayer film (MF-) electrodes, including the sheet resistance, volumetric capacitance, and charge/discharge ratio, were determined by the morphological modification and the method used to reduce the graphene oxide (GO) to reduced graphene oxide (RGO) in the multilayer films. The PANi and GO concentrations could be modulated to control the morphology of the GO monolayer film in the multilayer assemblies. Optical ellipsometry was used to determine the thickness of the GO film in a single layer (1.32 nm), which agreed well with the literature value (～1.3 nm). Hydroiodic acid (HI), hydrazine, or pyrolysis were tested for the reduction of GO to RGO. HI was found to be the most efficient technique for reducing the GO to RGO in the multilayer assemblies while minimizing damage to the virgin state of the acid-doped PANi. Ultimately, the MF-electrode, which could be optimized by fine-tuning the nanostructure and selecting a suitable reduction method, exhibited an excellent volumetric capacitance, good cycling stability, and a rapid charge/discharge rate, which are required for supercapacitors. A MF-electrode composed of 15 PANi/RGO bilayers yielded a volumetric capacitance of 584 F/cm(3) at a current density of 3.0 A/cm(3). Although this value decreased exponentially as the current density increased, approaching a value of 170 F/cm(3) at 100 A/cm(3), this volumetric capacitance is one of the best yet reported for the other carbon-based materials. The intriguing features of the MF-electrodes composed of PANi/RGO multilayer films offer a new microdimensional design for high energy storage devices for use in small portable electronic devices.     

Surface and Interface Engineering of Graphene Oxide Films by Controllable Photoreduction

We report herein the engineering of the surface/interface properties of graphene oxide (GO) films by controllable photoreduction treatment. In our recent works, typical photoreduction processes, including femtosecond laser direct writing (FsLDW), laser holographic lithography, and controllable UV irradiation, have been employed to make conductive reduced graphene oxide (RGO) microcircuits, hierarchical RGO micro‐nanostructures with both superhydrophobicity and structural color, as well as moisture‐responsive GO/RGO bilayer structures. Compared with other reduction protocols, for instance, chemical reduction and thermal annealing, the photoreduction strategy shows distinct advantages, such as mask‐free patterning, chemical‐free modification, controllable reduction degree, and environmentally friendly processing. These works indicate that the surface and interface engineering of GO through controllable photoreduction of GO holds great promise for the development of various graphene‐based microdevices.     

Concise,Single-Step Synthesis of Sulfur-Enriched Graphene: Immobilization of Molecular Clusters and Battery Applications

The concise synthesis of sulfur-enriched graphene for battery applications is reported. The direct treatment of graphene oxide (GO) with the commercially available Lawesson's reagent produced sulfur-enriched-reduced GO (S-rGO). Various techniques, such as X-ray photoelectron spectroscopy (XPS), confirmed the occurrence of both sulfur functionalization and GO reduction. Also fabricated was a nanohybrid material by using S-rGO with polyoxometalate (POM) as a cathode-active material for a rechargeable battery. Transmission electron microscopy (TEM) revealed that POM clusters were individually immobilized on the S-rGO surface. This battery, based on a POM/S-rGO complex, exhibited greater cycling stability for the charge-discharge process than a battery with nanohybrid materials positioned between the POM and nonenriched rGO. These results demonstrate that the use of sulfur-containing groups on a graphene surface can be extended to applications such as the catalysis of electrochemical reactions and electrodes in other battery systems.     

A Flexible Method for Covalent Double Functionalization of Graphene Oxide

A method for the double functionalization of graphene oxide (GO) under mild alkaline conditions has been developed. Two functional groups were covalently linked to GO in two steps: the first group was attached by an epoxide ring‐opening reaction and the second, bearing an amine function, was covalently conjugated to benzoquinone attached to the GO. The doubly functionalized GO was characterized by several techniques, confirming the sequential covalent modification of the GO surface with two different functional groups. This method is straightforward and the reaction conditions are mild, allowing preservation of the structure and properties of GO. This strategy could be exploited to prepare multifunctional GO conjugates with potential applications in many fields ranging from materials science to biomedicine.     

Comparative Studies on Electrocatalytic Activities of Chemically Reduced Graphene Oxide and Electrochemically Reduced Graphene Oxide Noncovalently Functionalized with Poly(methylene blue)

This study compares the electrocatalytic activities of chemically reduced graphene oxide (crGO) and electrochemically reduced graphene oxide (erGO), which are both noncovalently functionalized with a polyaromatic dye, poly(methylene blue) (polyMB), toward the oxidation of β‐nicotinamide adenine dinucleotide (NADH). PolyMB‐crGO and polyMB‐erGO composites were obtained via electropolymerization of methylene blue on crGO and GO modified glassy carbon (GC) electrodes, respectively. Cyclic voltammetry (CV) results indicate that these two types of integrated electrodes reveal different electrocatalytic activities. PolyMB‐crGO integrated electrode possesses lower catalytic oxidation potential, suggesting higher catalytic activity. The present study is helpful for the understanding and screening of graphene‐based advanced carbon nanomaterials for potential electrochemical applications.     

不同表面修饰石墨烯载Pd催化剂对甲酸氧化的电催化性能

采用对氨基苯磺酸对氧化石墨烯（GO）进行表面功能化,进而负载贵金属Pd,解决了Pd团聚和不易在载体表面负载的问题,从而提高了Pd基催化剂对于甲酸的催化能力。 实验研究了相同实验条件下,Pd在氧化石墨烯、还原石墨烯（RGO）和磺化处理的石墨烯（SGO）表面的分散和负载量以及得到的复合催化剂的催化性能。 实验结果表明,SGO更容易负载贵金属,得到的催化剂对O2气的电催化还原能力优于Pd/GO和Pd/RGO,此外Pd/SGO催化剂对CO的耐受力也明显提升,这可能是苯环上的π-π键和-SO3H的范德华力协同作用更有利于Pd的固定与分散。 对Pd/SGO催化氧还原的机理也进行了分析,该氧还原为2电子反应过程。     

Functional Graphene by Thiol‐ene Click Chemistry

Thiol‐ene click reaction was successfully employed for chemical modification of graphene oxide (GO) by one‐step synthesis. Herein, 2,2‐azobis(2‐methylpropionitrile) (AIBN) was used as thermal catalyst and cysteamine hydrochloride (HS?(CH₂)₂?NH₂HCl) was used as thiol‐containing compound, which is incorporated to GO surface upon reaction with the C=C bonds. The hydrochloride acts as protecting group for the amine, which is finally eliminated by adding sodium hydroxide. The modified GO contains both S‐ and N‐containing groups (NS‐GO). We found that NS‐GO sheets form good dispersion in water, ethanol, and ethylene glycol. These graphene dispersions can be processed into functionalized graphene film. Besides, it was demonstrated that NS‐GO was proved to be an excellent host matrix for platinum nanoparticles. The developed method paves a new way for graphene modification and its functional nanocomposites.     

Decomposition of Fluorinated Graphene under Heat Treatment

Fluorination modifies the electronic properties of graphene, and thus it can be used to provide material with on‐demand properties. However, the thermal stability of fluorinated graphene is crucial for any application in electronic devices. Herein, X‐ray photoelectron spectroscopy (XPS), temperature‐programmed desorption (TPD), and Raman spectroscopy were used to address the impact of the thermal treatment on fluorinated graphene. The annealing, at up to 700 K, caused gradual loss of fluorine and carbon, as was demonstrated by XPS. This loss was associated with broad desorption of CO and HF species, as monitored by TPD. The minor single desorption peak of CF species at 670 K is suggested to rationalize defect formation in the fluorinated graphene layer during the heating. However, fluorine removal from graphene was not complete, as some fraction of strongly bonded fluorine can persist despite heating to 1000 K. The role of intercalated H₂O and OH species in the defluorination process is emphasised.     

石墨烯氧化物薄膜电极的光电化学特性

采用浸渍-提拉法制备了一系列石墨烯氧化物(GO)薄膜,并通过X射线衍射(XRD),扫描电镜(SEM),傅里叶变换红外光谱,紫外-可见吸收光谱和光电化学测量等技术对样品进行了表征.在GO电极上观察到阴极光电流,且光电流密度受薄膜的厚度影响.GO薄膜电极厚度为27nm时,光电流密度为0.25μA·cm-2.此外,GO电极的光电响应还受紫外光照影响,随着紫外光照时间的延长,阴极光电流逐渐减小.该工作提供了简便的通过控制薄膜厚度或紫外光照时间来控制GO薄膜半导体光电化学性能的方法.