电沉积制备ZnO纳米棒修饰电极上氧化还原蛋白的电化学行为

采用恒电位阴极还原法在金电极表面一步修饰ZnO纳米棒, 制备成ZnO纳米棒修饰电极. 扫描电子显微镜(SEM)和X射线衍射(XRD)结果显示制得的ZnO为直径约100 nm的六棱柱状纤锌矿晶体纳米棒. 使用ZnO纳米棒修饰的金电极研究细胞色素c的直接电化学行为, 结果表明: ZnO纳米棒修饰的金电极能有效探测到细胞色素c的铁卟啉辅基在不同价态下的电化学行为; 细胞色素c吸附后, ZnO纳米棒修饰的金电极对过氧化氢的电流响应呈现良好的线性关系.     

细胞色素c在2-巯基嘧啶衍生物修饰金电极上的直接电化学

用循环伏安法研究了2-巯基嘧啶(MP)、4-氨基-2-巯基嘧啶(AMP)及4,6-二氨基-2-巯基嘧啶(DAMP)自组装修饰金电极的制备及其对细胞色素c直接电子传递的促进作用。用扫描电子显微镜(SEM)表征了2-巯基嘧啶衍生物修饰金电极的表面形貌。细胞色素c在MP、AMP修饰金电极上能进行准可逆的电化学反应,氧化还原峰电位差(ΔEp)分别为61 mV和86 mV,氧化与还原峰电流比ipa/ipc接近1,峰电流与电位扫描速率平方根(v1/2)呈正比,是扩散控制的准可逆过程,异相电子迁移速率常数(Ks)分别为1.4×10-3cm·s-1和5.1×10-5cm·s-1。金电极在2.0 mmol·L-1MP、AMP溶液中分别浸泡3 h和9 h,促进效果较好。随2-巯基嘧啶环上取代氨基数的增加,对细胞色素c电化学反应的促进作用及电极的稳定性逐渐减弱,即MP>AMP,而DAMP基本无促进作用。     

三维有序结构的金掺杂纳米TiO_2修饰电极用于H_2O_2的测定

在ITO玻璃表面构建了三维有序多孔结构的金掺杂纳米Ti O2薄膜(3DOM GTD/ITO),同时制备了一种细胞色素c(Cyt c)酶生物传感器(Cyt c/3DOM GTD/ITO)。通过透射电镜(TEM)、扫描电镜(SEM)对修饰电极进行表征。紫外-可见光谱实验表明吸附在GTD上的Cyt c能够保持其生物活性,二级结构未被破坏。同时研究了Cyt c在3DOM GTD/ITO修饰电极表面的直接电化学及对H2O2的电催化行为。结果显示,Cyt c在3DOM GTD/ITO修饰电极上有显著的直接电化学响应,峰电流与扫描速度呈线性关系,说明该电极过程是表面电化学控制过程。Cyt c/3DOM GTD/ITO修饰电极对H2O2具有良好的催化性能,线性范围为3.0×10-7~1.70×10-5mol/L,检出限为3.6×10-8mol/L(S/N=3),响应时间为5 s,且该修饰电极具有较好的重现性和稳定性。     

细胞色素c在羟基磷灰石修饰玻碳电极上的直接电化学

采用沉淀法合成羟基磷灰石纳米晶体，由于具有独特的多吸附位点特征，羟基磷灰石可作为一种新型电子传递促进剂用于细胞色素c的直接电化学研究．在pH7．0的磷酸盐缓冲溶液中，细胞色素c在羟基磷灰石修饰玻碳电极表面于0．074V(vs．Ag/AgC1)处有一对准可逆的氧化还原峰，为细胞色素c血红素辅基Fe(Ⅲ)／Fe(Ⅱ)电对的特征峰．实验结果表明细胞色素c与羟基磷灰石之间的静电作用．促进了细胞色素c在玻碳电极表面扩散控制的准可逆单电子转移过程．讨论了电位扫描速度、溶液离子强度对细胞色素c直接电化学的影响．     

细胞色素c／L-半胱氨酸修饰金电极检测亚硝酸根

采用循环伏安法、交流阻抗法研究了组装在L-半胱氨酸(L-Cys)修饰金电极上的细胞色素c(Cyt c)电化学行为;采用电化学方法以及紫外-可见光谱对电极进行表征.结果表明:通过静电吸附作用组装在L-Cys修饰金电极上的细胞色素c保持了良好的生物和电化学活性,用Cyt c/L-Cys修饰金电极检测亚硝酸根,响应电流与亚硝酸根浓度在5.0×10-6～4.5×10-4mol·L-1范围内呈线性关系,线性回归方程为Ip=0.031 c 8.165×10-6,相关系数为0.999 5,检出限(S/N=3)为1.5×10-7mol·L-1.电极用于模拟样品及咸菜样品中亚硝酸根的测定,回收率为89.0%～116.0%.     

细胞色素c在微带金电极上的直接电化学

报道了一种新的促进剂4,6-二甲基-2-巯基嘧啶(DMMP)对细胞色素c(Cyt.c) 电化反应的促进作用,用红外光谱和光电子能对DMMP 在金电极表面形成的单分子膜进行了表征.循环伏安实验表明Cyt.c在DMMP修饰微电极上能发生准可逆的电化学反应,异相电子传递速率常数K~5为6.6×10^-^3cm/s,对DMMP修饰膜的稳定性进行了考察;讨论了Cyt.c发生电化学反应的异相电子传递速率常数K~5受电极, 表面促进剂的修饰量以及空气中氧影响的机理.     

壳聚糖修饰纳米纤维膜表面对氧化还原酶行为的影响

采用静电纺丝法制备了丙烯腈/丙烯酸共聚物(PANCAA)纳米纤维膜, 研究了纺丝液浓度对纤维形态的影响, 以扫描电子显微镜观察纤维形貌, 遴选得到最佳纺丝条件. 以1-乙基-3-(N,N-二甲基氨基丙基)碳二亚胺/N-羟基丁二酰亚胺(EDC/NHS)为偶联剂, 在纤维膜表面引入壳聚糖修饰层, 采用衰减全反射傅里叶变换红外光谱(ATR/FTTIR)、水接触角和称重法考察了修饰前后膜的变化. 通过戊二醛将过氧化氢酶固定到壳聚糖修饰的PANCAA纳米纤维膜上, 研究了壳聚糖及戊二醛浓度对固定化过氧化氢酶的影响, 结果表明, 在壳聚糖浓度为25 mg/mL及戊二醛质量分数为5%条件下, 壳聚糖修饰膜的固定化酶活性比空白膜提高了41.7%, 稳定性也得到了不同程度的提高.     

Study on Electrochemical Behavior of Controllable Interface Alkanethiols Selfassembled Monolayers and Au Nanoparticles Modified Gold Electrode

在裸金电极上自组装不同比例的4,4’-二甲基联苯硫醇(MTP)和硫辛酸(TA)混合液,形成自组装膜( MTP+ TA/Au SAMs),再修饰纳米金,制得纳米金混合巯基修饰金电极(AuNPs/MTP+ TA/Au).研究了纳米金混合巯基修饰金电极的电化学行为和阻抗行为,结果表明电极表面pH值的改变对电极表面的电子转移有重要影响.对葡萄糖传感器的制备条件、测定条件、抗干扰能力等进行了讨论,结果表明修饰电极的微结构和微环境有必要进一步研究.     

辣根过氧化物酶在壳聚糖和无掺杂金刚石纳米粒子共沉积膜上的固定及其直接电化学

无掺杂的金刚石纳米粒子(UND)可以和壳聚糖共沉积到玻碳电极表面,形成壳聚糖-UND复合膜.此复合膜可以通过吸附的方法,固定辣根过氧化物酶(HRP),并且能够实现HRP的直接电化学,保持HRP对过氧化氢的良好催化能力.为了进一步研究此复合膜及HRP在此复合膜上的电化学活性,运用扫描电子显微镜(SEM)、全反射红外(ATR)、电化学交流阻抗、循环伏安等技术来跟踪各步修饰过程.结果表明,此复合膜有良好的生物相容性,能够很好的保持HRP的生物活性.     

电聚合茜素黄R构建辣根过氧化物酶传感器的研究

利用电聚合茜素黄R(AYR)的方法,将辣根过氧化物酶(HRP)和细胞色素c(Cyt c)固载于通过一步法电沉积的碳纳米管-金纳米粒子(MWCNTsAu NPs)复合纳米材料修饰电极表面,构筑PAYR-HRP-Cyt c/M WCNTs-Au NPs修饰电极,并利用HRP对H2O2的直接电化学催化行为对H2O2进行检测。采用扫描电镜对MWCNTs-Au NPs和PAYR-HRP-Cyt c的表面形貌进行表征。利用电化学阻抗对修饰电极的构筑过程进行了监测。采用循环伏安法和计时电流法对修饰电极的电化学行为进行了研究。探讨了p H和电位对该修饰电极测定H2O2的性能的影响。该传感器对H2O2在5.0×10-7~3.14×10-3mol/L范围内呈良好的线性响应,相关系数为0.9997,灵敏度为0.50 A·L/mol,检出限(S/N=3)为9.6×10-8mol/L。     

Selective Electrochemical Determination of Salicylic Acid in Wheat Using Molecular Imprinted Polymers

Salicylic acid is a phytohormone, playing crucial roles in signal transduction, crop growth, and development, and defense to environmental challenges. In this study, a highly selective electrochemical sensor was designed and used to determine salicylic acid using molecularly imprinted polymers for recognition. The electrochemical sensor was fabricated via stepwise modification of gold nanoparticle–graphene–chitosan and molecularly imprinted polymers on a glassy carbon electrode. With electrochemical deposition, a gold nanoparticle–graphene–chitosan film was deposited on the glassy carbon electrode and enhanced the sensitivity. Molecularly imprinted polymers with adsorbed template salicylic acid were added to the surface of the modified electrode. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the modified electrodes. Salicylic acid in wheat was quantified by the sensor using the molecularly imprinted polymer/gold nanoparticle–graphene–chitosan/glassy carbon electrode. Concentrations of salicylic acid from 5?×?10^?10 to 5?×?10^?5?mol?L^?1 were determined showing that the developed sensor was suitable for the analysis of food.     

纳米金–壳聚糖修饰电极循环伏安法测定抗坏血酸

介绍纳米金–壳聚糖修饰电极的制备方法及其测定抗坏血酸的分析应用。采用电沉积方法,将氯金酸与壳聚糖的混合电解液直接共沉积,制备了壳聚糖–纳米金修饰玻碳电极的电化学传感器。利用循环伏安法研究了抗坏血酸浓度、p H值等对抗坏血酸在修饰电极上的电化学行为的影响。实验结果表明,修饰电极对抗坏血酸具有良好的电催化氧化作用,抗坏血酸浓度在5×10~(–5)~1×10~(–3) mol/L范围内线性良好,回归方程为I_p=0.433 8c+0.881 9,相关系数为0.998 71。该法可指导纳米金–壳聚糖修饰电极的制备及抗坏血酸含量的测定。     

A simple method to fabricate a chitosan-gold nanoparticles film and its application in glucose biosensor

A novel film of chitosan-gold nanoparticles is fabricated by a direct and facile electrochemical deposition method and its application in glucose biosensor is investigated. HAuCl(4) solution is mixed with chitosan and electrochemically reduced to gold nanoparticles, which can be stabilized by chitosan and electrodeposited onto glassy carbon electrode surfaces along with the electrodeposition of chitosan. Then a model enzyme, glucose oxidase (GOD) is immobilized onto the resulting film to construct a glucose biosensor through self-assembly. The resulting modified electrode surfaces are characterized with both AFM and cyclic voltammetry. Effects of chitosan and HAuCl(4) concentration in the mixture together with the deposition time and the applied voltage on the amperometric response of the biosensor are also investigated. The linear range of the glucose biosensor is from 5.0 x 10(-5) approximately 1.30 x 10(-3) M with a Michaelis-Menten constant of 3.5 mM and a detection limit of about 13 microM.     

Effect of Various Deposition Techniques,Electrode Materials and Posttreatment with Tetrabutylammonium and Tetrabutylphosphonium Salts on the Electrochemical Behavior and Stability of Various Prussian Blue Modified Electrodes

The effect of various deposition techniques, electrode materials and posttreatment with tetrabutylammonium and tetrabutylphosphonium salts on the electrochemical behavior and stability of various Prussian blue (PB) modified electrodes, namely PB modified glassy carbon electrodes, silicate‐film supported PB modified glassy carbon electrodes, PB‐doped silicate glassy carbon electrodes, PB modified carbon ceramic electrodes using electrochemical deposition and PB modified carbon ceramic electrodes using chemical deposition is reported. Cyclic voltammetry and amperometric measurements of hydrogen peroxide were performed in a flow injection system while the carrier phosphate buffer (pH 7.0) with a flow rate of 0.8 mL min^?1 was propelled into the electrochemical flow through cell housing the PB modified working electrode as well as an Ag|AgCl|0.1 M KCl reference and a Pt auxiliary electrode. The results showed that the deposition procedure, electrode material and posttreatment with additional chemicals can significantly alter the stability and electrochemical behavior of the PB film. Among the studied PB modified electrodes, those based on carbon ceramic electrodes modified with a film of electropolymerized PB showed the best electrochemical stability.     

Comparative studies on electrogenerated chemiluminescence of luminol on gold nanoparticle modified electrodes

Comparative studies on the electrogenerated chemiluminescence (ECL) behavior of luminol on various electrodes modified with gold nanoparticles of different size were carried out in neutral solution by conventional cyclic voltammetry (CV). The results demonstrated that the gold nanoparticle modified electrodes could generate strong luminol ECL in neutral pH conditions. The catalytic performance of gold nanoparticle modified electrodes on luminol ECL depended not only on the gold nanoparticles but also on the substrate. Gold electrode and glassy carbon electrode were the most suitable substrates for the self-assembly of gold nanoparticles. Moreover, the gold nanoparticle modified gold and glassy carbon electrode had satisfying stability and reproducibility and did not need tedious pretreatment of electrode surface before each measurement. It was also found that luminol ECL behavior depended on the size of gold nanoparticles. The most intense ECL signals were obtained on a 16-nm-diameter gold nanoparticle modified electrode. The modified electrode prepared by the self-assembly method exhibited much better catalytic effect on luminol ECL than that prepared by the electrically deposited method. The ECL behavior of luminol on a gold nanoparticle self-assembled gold electrode was also investigated by other transient-state electrochemical techniques, such as chronoamperometry, differential pulse voltammetry, normal pulse voltammetry, and square wave voltammetry. The strongest ECL intensity was obtained under square wave voltammetric condition.     

细胞色素c在纳米杂化膜修饰玻碳电极上的直接电化学

以多壁碳纳米管(MWNTs)修饰玻碳(GC)电极为基底,自组装金纳米粒子(AuNPs)及L-半胱氨酸(L-Cys)研制杂化膜修饰电极(L-Cys/AuNPs/MWNTs/GC).实验表明,该膜修饰电极在pH=7.0的KH2PO4-K2HPO4缓冲溶液中对细胞色素c(Cyt c)的直接电子转移反应具有良好的电催化作用,C...     

Pulsed Deposited Manganese and Vanadium Oxide Film Modified with Carbon Nanotube and Gold Nanoparticle: Chitosan and Ionic Liquid‐based Biosensor

Present study describes the synthesis of mixed oxide films of manganese and vanadium by electrochemical pulsed deposition technique on a glassy carbon electrode (GCE) modified with multiwall carbon nanotubes (MWCNT). The film was further decorated with gold nanoparticles to enhance the reduction signal of dissolved oxygen in pH 5.17 acetate buffer solution. All of the electrochemical synthesized modified electrodes have been characterized with Scanning electron microscopy(SEM), High‐resolution transmission electron microscopy (HRTEM), X‐Ray photoelectron spectroscopy (XPS), X‐Ray diffraction (XRD) techniques. The electrode obtained (AuNPs/MnOx?VOx/CNT/GCE) was utilized as a platform for glucose biosensor where the glucose oxidase enzyme was immobilized on the composite film with the aid of chitosan and an ionic liquid. The electrochemical performance of the biosensor was investigated by cyclic voltammetry and the relative parameters have been optimized by amperometric measurements in pH 5.17 acetate buffer solution. The developed biosensor exhibited a linear range for glucose between 0.1–1.0 mM and the limit of detection was calculated as 0.02 mM.     

Bioelectrocatalysis by Microperoxidase‐11 in a Multilayer Architecture of Chitosan Embedded Gold Nanoparticles

We report on the redox behaviour of the microperoxidase‐11 (MP‐11) which has been electrostatically immobilized in a matrix of chitosan‐embedded gold nanoparticles on the surface of a glassy carbon electrode. MP‐11 contains a covalently bound heme c as the redox active group that exchanges electrons with the electrode via the gold nanoparticles. Electroactive surface concentration of MP‐11 at high scan rate is between 350±50 pmol cm^?2, which reflects a multilayer process. The formal potential (E°′) of MP‐11 in the gold nanoparticles‐chitosan film was estimated to be ?(267.7±2.9) mV at pH 7.0. The heterogeneous electron transfer rate constant (k_s) starts at 1.21 s^?1 and levels off at 6.45 s^?1 in the scan rate range from 0.1 to 2.0 V s^?1. Oxidation and reduction of MP‐11 by hydrogen peroxide and superoxide, respectively have been coupled to the direct electron transfer of MP‐11.     

Gold nanoparticle-modified glassy carbon electrode for electrochemical investigation of aliphatic di-carboxylic acids in aqueous media

The electrochemical reduction of di-carboxylic acids; oxalic, succinic, malic, and tartaric have been studied on the gold nanoparticles modified electrode in aqueous media solution of 0.1 M KCl. Gold nanoparticle (Au_NPs)-modified electrodes were prepared by the electrodeposition with cyclic voltammetric method onto glassy carbon electrode in acidic media. The surface morphology of the electrodeposited gold nanoparticles was examined by SEM. Also, the electrochemical properties of the prepared electrodes were investigated with different electrochemical techniques; cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy. Cyclic voltammetric, chronoamperometric, and electrochemical impedance spectroscopic techniques were used for investigating the electrochemical behavior of the particulate acids. The modification of the electrode with Au nanoparticles (Au_NPs) enables the appearance of cyclic voltammogram peaks completely clear and sharp for the acids under investigation in comparison with the poor behavior of them in absence of the modification. All acids undergo totally irreversible redox reaction in neutral and acid media. The cyclic voltammetric response of the investigated acids is sensitive to pH, as well as of the scan rate. Each acid has a different reduction peak position from the other acids depending on the structure of the acid undergo the electroreduction process. Further, the lowest unoccupied molecular orbital energies of the investigated acids have been theoretically evaluated and are compared with their electroreduction potential peaks.     

Construction of an electrochemical sensor based on the electrodeposition of Au-Pt nanoparticles mixtures on multi-walled carbon nanotubes film for voltammetric determination of cefotaxime

Mixtures of gold-platinum nanoparticles (Au-PtNPs) are fabricated consecutively on a multi-walled carbon nanotubes (MWNT) coated glassy carbon electrode (GCE) by the electrodeposition method. The surface morphology and nature of the hybrid film (Au-PtNPs/MWCNT) deposited on glassy carbon electrodes is characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) techniques. The modified electrode is used as a new and sensitive electrochemical sensor for the voltammetric determination of cefotaxime (CFX). The electrochemical behavior of CFX is investigated on the surface of the modified electrode using linear sweep voltammetry (LSV). The results of voltammetric studies exhibited a considerable improvement in the oxidation peak current of CFX compared to glassy carbon electrodes individually coated with MWCNT or Au-PtNPs. Under the optimized conditions, the modified electrode showed a wide linear dynamic range of 0.004-10.0 μM with a detection limit of 1.0 nM for the voltammetric determination of CFX. The modified electrode was successfully applied for the accurate determination of trace amounts of CFX in pharmaceutical and clinical preparations.