K2S2O8/Na2SO3引发St/BA微乳液共聚合的研究

以十二烷基硫酸钠／十二烷基苯磺酸钠(SDS／SDBS)为乳化剂，过硫酸钾／亚硫酸钠(K2S2O3／Ni2SO3)为引发剂进行苯乙烯／丙烯酸丁酯(SL／BA)微孔液共聚合反应。研究了引发剂浓度[I]OR、单体总浓度[M]、乳化剂含量[E]和聚合温度T对微孔液共聚合最大反应速率Rmax和共聚物粘均分子量^-Mη的影响，测定了共聚单体的竞聚率，结果得到：Rmax∝[I]^0.98OR[M]^0.81[E]^-0．34e^-4712／T，^-Mη∝[I]^-0.27OR[M]^0.48[E]^-0.68e^2304/T；rSt=0.598，rBA=0.0206。     

复合微乳液聚合制备P(MMA-UA)纳米乳胶粒子的研究

将聚氨酯预聚体可聚合乳化剂 (APUA)和甲基丙烯酸甲酯 (MMA)的复合微乳液体系 ,分别用水溶性过硫酸钾 (K2 S2 O8)和油溶性偶氮二异丁腈 (AIBN)作引发剂 ,进行微乳液聚合研究 ,制备了P(MMA UA)复合纳米乳胶粒子 .研究了APUA用量、聚合温度对聚合动力学的影响 ;用透射电子显微镜 (TEM)观察了不同乳化剂浓度及引发剂体系对胶粒形态、大小及分布的影响 .结果表明 ,用可聚合乳化剂APUA可制得稳定性很好的P(MMA UA)纳米级核 壳型乳胶粒子 ,乳胶粒径在 5 0nm左右 .随着乳化剂用量增加 ,粒子变小 ;不同类型的引发剂对胶乳的性质有较大影响 ,以APUA为乳化剂 ,K2 S2 O8为引发剂 ,在聚合反应过程中或在聚合反应后的放置中 ,会出现P(MMA UA)的纳米水凝胶 (Nanogel)现象 .     

超声辐照引发MMA微乳液聚合

研究了超声波引发甲基丙烯酸甲酯(MMA)的微乳液聚合.辐照40min时单体转化率高达90%.透射电镜观察发现,PMMA微乳液平均粒径为36.5nm,粒径分布窄,表明超声波引发是制备PMMA微乳液的有效方法.采用分光光度计对微乳液聚合过程中乳胶粒的形成和大小进行了间接表征,研究了超声功率输出、乳化剂、助乳化剂、单体和引发剂对MMA微乳液聚合的影响.     

粒径可控阳离子型聚苯乙烯纳米粒子的制备及表征

在采用阳离子型双子（gemini）表面活性剂作为乳化剂,不使用任何助乳化剂的条件下,通过改进微乳液聚合工艺制备了窄分布粒径可控的阳离子型聚苯乙烯（PS）纳米乳液。 改进微乳液聚合的主要特点是：大部分苯乙烯以预乳液的形式恒速滴入引发聚合的微乳液中,使用具有高乳化性能的gemini表面活性剂作为乳化剂能明显降低乳胶粒粒径。 实验结果表明,少量阳离子单体三甲基烯丙基氯化铵作为共聚单体能够明显减小Z均粒径、降低粒度分布,乳化剂用量、引发剂用量和反应温度均能影响制备乳胶粒的粒径及其粒度分布。 乳化剂和引发剂用量分别为苯乙烯质量的5%~10%和1.0%~1.5%、反应温度为70~75 ℃时,能够制备粒径小分布窄的阳离子型聚苯乙烯纳米粒子。 Z均粒径与苯乙烯质量之间的线性关系表明,Z均粒径可以通过苯乙烯用量来控制。 不同聚合工艺下制备的聚合物粒度分布曲线表明,改进微乳液聚合工艺（半连续预乳化工艺）在制备窄分布的聚合物纳米粒子方面具有很强的优越性。     

A novel method for preparing monodispersed polystyrene nanoparticles

A preparation manner for monodispersed polystyrene (PS) nanoparticles polymerized by using a novel addition procedure of a monomer is suggested. In systems containing a smaller amount of surfactant compared with conventional microemulsion polymerization, the polymerization processes consists of three stages: adding dropwise the first part of the monomer for a few minutes at 80°C and polymerizing for 1 h; adding collectively the residual part of the monomer and polymerizing at the same temperature for another 1 h; and then polymerizing at 85°C for another 1 h. Based on discussions on the nucleation mechanism of particles in the polymerization system, the influences of monomer weight added dropwise, and amounts of initiator and emulsifier on the size and distribution of PS particles were investigated. PS nanoparticles with smaller diameter such as a number-average diameter of 18.7 nm and better monodispersity were obtained since the dropped styrene amount was suitable under 20wt-% emulsifier amount and 3wt-% initiator amount based on the monomer. Translated from Journal of Nanjing University (Natural Science), 2006, 2 (in Chinese)     

Effect of two Kinds of Imidazolium Ionic Liquids on the Microemulsion Polymerization of Methyl methylacrylate

Summary: In this paper, the microemulsion polymerization of methyl methylacrylate (MMA) was carried out with single and gemini ionic liquids as emulsifier including 1-N-tetradecyl-3-methylimidazolium bromide (C₁₄MIM · Br) and 1, 4-Bis (3-tetradecylimidazolium-1-yl) butane bromide (C₁₄MIM-4-C₁₄MIM · 2Br) respectively, and they were all have typical microemulsion polymerization characters of MMA, but the process of polymerization directly depends on the structure of the imidazolium ionic liquids. The structure and concentration of ionic liquids have effects on the resulted latex particle sizes of PMMA, and much smaller size latexes of PMMA could be gotten with C₁₄MIM · Br as emulsifier than C₁₄MIM-4-C₁₄MIM · 2Br in polymerization. On the other hand, the structure of emulsifier has the effects on the molecular weight (MW) and molecular weight distribution (MWD) of PMMA, so the resulting PMMA prepared from microemulsion polymerization with C₁₄MIM · Br as emulsifier has higher MW but narrower MWD than that of PMMA with the same dosage of C₁₄MIM-4-C₁₄MIM · 2Br as emulsifier.     

丙烯酸酯纳米乳液的制备与表征

将甲基丙烯酸羟乙酯(HEMA)与甲基丙烯酸(MAA)或丙烯酸(AA)用作甲基丙烯酸甲酯(MMA)／丙烯酸丁酯(BA)乳液聚合体系的反应性助乳化剂，采用一种改进的微乳液聚合方法，合成了高单体／乳化剂比例(大于40：1)的聚丙烯酸酯纳米乳液．讨论了引发剂、乳化剂、助乳化别对乳胶粒大小和胶膜吸水率的影响，并对乳液的流体力学行为，共聚物的拉伸行为及耐水性等进行了研究．     

High monomer content batch microemulsion polymerization of butyl acrylate initiated with gamma ray

Radiation polymerization of butyl acrylate was performed in a microemulsion stabilized with a mixture of sodium of 12-acryloxy-9-octadecenoic acid and sodium dodecyl sulfate in a weight ratio of 2 at room temperature. BA content in microemulsion can be successfully improved up to 40 wt% with low surfactant concentration (lower than 10 wt%). The resulted stable, translucent microlatex contain particles with average diameter from 28.1 to 38.1 nm with different monomer content. Particle size depends on the dose rate and surfactant concentration. Effects of monomer content and dose rate on the maximum polymerization rate are discussed.     

高固含量低粘度P(MMA/BA/AA)乳液的制备及性能研究

先利用半连续种子乳液聚合法制备固含量为50%,粒径480nm的单分散甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)与丙烯酸(AA)的共聚物种子乳液;然后以上述种子乳液为介质,十二烷基硫酸钠为乳化剂,碳酸氢钠为缓冲剂,过硫酸铵为引发剂制备固含量72%,乳胶粒具有二元分布特征的高固含量、低粘度稳定乳液:其中大乳胶粒径500～600nm,小乳胶粒径约80nm.所得乳液中乳化剂总含量为聚合物质量的2.1%;粘度在剪切速率为21s-1时为400mPa·s.另外,相对于常规乳液,所制备高固含量乳液胶膜具有更好的光泽度.     

Preparation of Acrylic Microgels by Modified Microemulsion Polymerization and Phase Inversion

Semi‐transparent reactive microgel in nanosize has been prepared by modified microemulsion polymerization using a common emulsifier, crosslinking agent and functional monomer. The microgels are translucent reactive nanoparticles, with the size of 40–100 nm, consisting of inner‐crosslinked polymer up to 40%. FT‐IR proved the functional groups, such as epoxy and hydroxy, are on the surface of the microgel nanoparticles. Rheological detection demonstrated the apparent pseudoplasticity of the non‐aqueous microgel dispersion prepared by the phase transfering from the O/W microlatexes.     

Radiation-induced copolymerization of styrene/n-butyl acrylate in the presence of ultra-fine powdered styrene–butadiene rubber

Styrene (St)/n-butyl acrylate (BA) copolymers were prepared by two-stage polymerization: St/BA was pre-polymerized to a viscous state by bulk polymerization with initiation by benzoyl peroxide (BPO) followed by ⁶⁰Co γ-ray radiation curing. The resultant copolymers had higher molecular weight and narrower molecular weight distribution than conventional methods. After incorporation of ultra-fine powdered styrene–butadiene rubber (UFSBR) with a particle size of 100 nm in the monomer, the glass transition temperature (T_g) of St–BA copolymer increased at low rubber content. Both the St–BA copolymer and the St–BA copolymer/UFSBR composites had good transparency at BA content below 40%.     

超声无皂乳液聚合制备BA/St/AM三元共聚物乳胶粒及其聚合机理研究

将超声技术引入到无皂乳液聚合方法中,在不加入任何引发剂和乳化剂的情况下,制备了丙烯酸丁酯(BA)/苯乙烯(St)/丙烯酰胺(AM)三元共聚纳米乳胶粒.研究了不同超声时间对单体转化率、乳胶粒粒径以及乳液粘度的影响.同时还探讨了超声无皂乳液聚合机理,认为AM在聚合过程中起到了引发和稳定的作用.TEM照片表明,乳胶粒直径大约在80nm左右,FTIR及DSC分析表明产物为三元共聚物,而不是共混物.     

Micellar nucleation differential microemulsion polymerization

Polymer nanoparticles within the range of 2–5 nm with a solid content of more than 13 wt.% and a narrow molecular weight polydispersity (Mw/Mn ∼ 1.1) were for the first time prepared using a micellar nucleation differential microemulsion polymerization system emulsified by sodium dodecyl sulfate (SDS), with SDS/monomer (methyl methacrylate) and SDS/H₂O weight ratios of up to 1:16 and 1:100, respectively. It was found that for benzoyl peroxide (BPO), micellar nucleation is more favorable for the synthesis of smaller polymer nanoparticles than ammonium persulfate (APS) which gives rise to homogeneous nucleation and 2,2′-azobisisobutyronitrile (AIBN) which involves partially heterogeneous nucleation. In the polymerization process, there exists a critical stability concentration (CSC) of SDS, above which the size of the nanoparticles is to be minimized and stabilized. With an increase in the monomer addition rate, the polymerization system changes from a microemulsion system to an emulsion system. A mechanism was proposed to describe the micellar nucleation process of differential microemulsion polymerization. This study may contribute to the development of fine polymer nanoparticles for drug delivery systems.     

Synthesis of polynorbornene‐poly(tert‐butyl acrylate) nanoparticles with original morphologies by tandem ROMP and ATRP in microemulsion

Composite latex particles based on homopolymers and graft‐copolymers composed of polynorbornene (PNB) and poly(tert‐butyl acrylate) (PtBA) were synthesized in microemulsion conditions by simultaneous combination of two distinct methods of polymerization: Ring‐opening metathesis polymerization (ROMP) and atom transfer radical polymerization (ATRP). Only one commercial compound (first generation Grubbs catalyst) was used to initiate the ROMP of norbornene (NB) and activate the ATRP of tert‐butyl acrylate (tBA). Well‐defined nanoparticles with hydrodynamic diameters smaller than 50 nm were prepared with original morphologies depending on the monomer compositions, the type of combination (polymer blend or graft‐copolymer), and the conditions of microemulsion polymerizations. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

AM/(2-甲基丙烯酰氧乙基)三甲基氯化铵/2-丙烯酰胺基-2-甲基丙基磺酸钠的反相微乳液共聚合动力学研究

通过实验绘制了失水山梨醇单月桂酸酯(Span20)-聚氧乙烯山梨醇酐单脂酸酯(Tween80)复配乳化剂、丙烯酰胺、(2-甲基丙烯酰氧乙基)三甲基氯化铵、2-丙烯酰胺基-2-甲基丙基磺酸钠和环己烷的拟三元相图.采用过硫酸铵-亚硫酸氢钠氧化还原引发剂,通过动力学研究,得到了聚合反应的表观活化能为68.10 kJ/mol,并分别得到了聚合速率与产物特性粘数的动力学关系式Rp∝[M]1.74[APS]0.60[E]-1.28,[η]∝[M]0.78[APS]-0.23[E]-0.71,分析了单体浓度、引发剂浓度、乳化剂浓度对共聚合反应速率Rp和共聚物特性粘数[η]作用及影响的原因,在动力学研究的基础上初步探讨了聚合机理.     

Micron-sized monodispersed polymer particles produced by seeded polymerization for the dispersion of high swelling of polymer particles with a large amount of monomer

 Micron-sized monodispersed polystyrene (PS)/poly(n-butyl methacrylate) composite particles were produced as follows. First, 1.77 μm-sized monodispersed PS seed particles produced by dispersion polymerization were dispersed in ethanol/water (1/2, w/w) medium dissolving poly(vinyl alcohol) as a stabilizer. n-Butyl methacrylate (BMA) monomer dissolving benzoyl peroxide initiator was emulsified in ethanol/water (1/2, w/w) solution of sodium dodecyl sulfate as emulsifier with ultrasonic homogenizer, and the BMA monomer emulsion was mixed with the PS seed emulsion. The PS seed particles absorbed with a large amount of BMA (about 150 times weight of the seed particles) for 2 h to about 10 μm in diameter while keeping good monodispersity and BMA droplets disappeared finally. The seeded polymerization was carried out at 70 °C after a certain amount of water was added to depress the redissolving of BMA from the swollen particles into the medium by raising from room temperature to the polymerzation temperature. Received: 21 February 1996 Accepted: 4 September 1996     

The effect of cosurfactants and the initiator concentration on the polymer to surfactant concentration in nanolatexes

The effect of cosurfactant and initiator concentration on the ab initio production of nanolatexes using low surfactant levels was investigated. While the use of cosurfactants (acrylic acid and pentanol) increased the amount of monomer that can be used in styrene‐SDS microemulsion formulations to 13 wt %, high surfactant concentrations are still required, resulting in polymer‐to‐surfactant ratios (Pol/Surf) <1. Latexes with particle size of 30 ± 5 nm were produced upon polymerization of these microemulsions. The Pol/Surf can be significantly increased by increasing the initiator concentration of emulsion polymerization recipes. Particle sizes are comparable with microemulsion latexes, however, less surfactant is required. The reduction in the particle size with higher initiator concentration is attributed to a higher efficiency of particle nucleation and to a higher nucleation rate relative to the rate of monomer transfer. Nanolatexes (particle size < 30 nm) were obtained with 19 wt % solids content and Pol/Surf of 3.6 in ab initio. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

微乳液聚合制备多孔高吸油甲基丙烯酸酯类树脂的研究

研究了双连续相微乳液聚合制备多孔高吸油树脂,以甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)为共聚单体(油相),水(H2O)/乙醇(EtOH)为混合水相,2,2′-偶氮二异丁腈(AIBN)为引发剂,采用十二烷基硫酸钠(SDS)和复配十二烷基硫酸钠/吐温80(SDS/T80)两种乳化体系,调节油相和水相比例,配制出双连续相微乳液.聚合在无搅拌下进行.研究了乳化体系、混合水相含量、单体配比、交联剂和引发剂用量等因素对树脂吸油性能的影响.结果表明,多孔高吸油树脂比同系无孔树脂的吸油速率大大提高,最快可以在2min内达到吸油饱和.树脂对苯,四氢呋喃,四氯化碳的吸油倍率分别达到15.5g/g,15.5g/g,31.7g/g.     

Microemulsion polymerization of butyl acrylate. IV. Effect of emulsifier concentration

The oil/water microemulsion polymerizations of butyl acrylate initiated by a water (ammonium peroxodisulfate, APS) or oil (dibenzoyl peroxide, DBP) soluble radical initiator at different emulsifier concentrations were investigated. The rate of polymerization vs. conversion curve shows two intervals. The rate of polymerization is found to decrease with the emulsifier concentration. This finding was discussed in terms of the decrease of both radical and monomer concentration, the chain transfer to emulsifier, desorption of chaintransferred radicals, and the contribution of solution polymerization. The polymerization is faster with APS. In the APS system the rate per particle or the number of radicals per particle increases exponentially with increasing particle size. The particle size and number increase during the whole polymerization. This behavior was discussed in terms of the nucleation of monomer-containing micelles and agglomeration of primary particles during the whole polymerization. © 1995 John Wiley & Sons, Inc.     

Particle nucleation and monomer partitioning in styrene O/W microemulsion polymerization

Particle nucleation in the polymerization of styrene microemulsions was found to take place throughout the polymerization as indicated by measurements of the particle number as a function of conversion. A mechanism based on the nucleation in the microemulsion droplets was proposed to explain the experimental findings although homogeneous nucleation and coagulation during polymerization were not completely ruled out. A thermodynamic model was developed to simulate the partitioning of monomer in the different phases during polymerization. The model predicts that the oil cores of the microemulsion droplets were depleted early in the polymerization (4% conversion). Due to the high monomer/polymer swelling ratio of the polymer particles, most of the monomer resides in the polymer particles during polymerization. The termination of chain growth inside the polymer particles was attributed to the chain transfer reaction to monomer. The low n? (less than 0.5) of the microemulsion system was attributed to the fast exit of monomeric radicals.