Solvothermal synthesis of K2V3O8 nanorods

A solvothermal route has been developed to synthesize K₂V₃O₈ nanorods via the reduction of V₂O₅ using ethanol as the reducing agent as well as the solvent at 200°C. X-ray diffraction and selected area electron diffraction analysis revealed that the as-synthesized products are of tetragonal structure K₂V₃O₈. Transmission electron spectroscopy image showed that the obtained K₂V₃O₈ comprises rod-like nanocrystallites. The formation mechanism of K₂V₃O₈ was studied.     

Anisotropic vapor phase growth of Ga2O3 crystalline nanobelts

Ga₂O₃ nanobelts were synthesized by gas reaction at high temperature in the presence of oxygen in ammonia. X-ray diffraction and chemical microanalysis revealed that the nanostructures were Ga₂O₃ with the monoclinic structure. Electron microscopy study indicated the nanobelts were single crystalline with broad (0 1 0) crystallographic planes. The nanostructures grew anisotropically with the growth direction of . Statistical analysis of the anisotropic morphology of the nanobelts and electron microscopy investigation of the nanobelt tips indicated that both vapor–solid and vapor–liquid–solid mechanisms controlled the growth process. The anisotropic nature of crystallographic morphology is explained in terms of surface energy.     

Flux growth of PbMg1/3Ta2/3O3 single crystals

Single crystals of PbMg_1/3Ta_2/3O₃ (PMT) were grown by the flux method. The PbO–Pb₃O₄–B₂O₃ system was used as a solvent. Transparent and light yellow PMT single crystals of rectangular shape and dimensions up to 10×6×4 mm³ were obtained. For the applied growth conditions only, the crystals of the perovskite structure were grown. X-ray diffraction tests showed that at room temperature PMT exhibits cubic symmetry with lattice parameter a=4.042(1) Å. Dielectric studies pointed to relaxor properties of PMT. The characteristic broad and frequency-dependent maximum of dielectric permittivity was observed at 179.7 K (1 kHz).     

Phase relations around langasite (La3Ga5SiO14) in the system La2O3–Ga2O3–SiO2 in air

Phase relations around langasite (LGS, La₃Ga₅SiO₁₄) were studied on the basis of phase assemblage observed during calcination and crystallization process of samples of various compositions in the ternary system La₂O₃–Ga₂O₃–SiO₂. A ternary compound of apatite structure, La₁₄Ga_xSi_9–xO_39–x/2 was found for the first time. Crystallization of this compound was observed in the cooling process of molten samples of stoichiometric LGS as well as LGS single crystal, demonstrating that LGS is an incongruent-melting compound. A phase diagram was established primarily based on the crystallization sequence in the cooling process.     

Oscillation of Y2BaCuO5 particle concentration in the melt-grown YBaCuO bulk superconductors

The oscillation of Y₂BaCuO₅ (2 1 1) particle concentration in form of bands parallel to the growth front was observed in top-seeded melt-grown (TSMG) single-grain YBa₂Cu₃O₇/Y₂BaCuO₅ bulk superconductors. The formations of these bands have been associated with temperature fluctuations at the growth front, which induce the fluctuation of the growth rate of the YBa₂Cu₃O₇ (123) crystal and consequently also the fluctuation of the amount of trapped 211 particles. We have shown that the oscillation of 211-particle concentration does not occur when the growth front is horizontal and the crystal solidifies from below upwards. In the a-growth sector (a-GS) the oscillation was observed only in the nests with very small 211 particles.     

A simple method to synthesize single-crystalline β-wollastonite nanowires

The single-crystalline β-wollastonite (β-CaSiO₃) nanowires were prepared via a simple hydrothermal method, in the absence of any template or surfactant using cheap and simple inorganic salts as raw materials. Xonotlite [Ca₆(Si₆O₁₇)(OH)₂] nanowires were first obtained after hydrothermal treatment at a lower temperature of 200 °C for 24 h, and after being calcinated at 800 °C for 2 h, xonotlite nanowires completely transformed into β-wollastonite nanowires and the wire-like structure was preserved. The synthesized β-wollastonite nanowires had a diameter of 10–30 nm, and a length up to tens of micrometers, and the single-crystalline monoclinic parawollastonite structured β-wollastonite was identified by XRD with the space group of P2₁/a and cell constants of a=15.42 Å, b=7.325 Å, c=7.069 Å and β=95.38°. A possible growth mechanism of β-wollastonite nanowires was also proposed. The advantages of this method for the nanowire synthesis lie in the high yield, low temperature and mild reaction conditions, which will allow large-scale production at low cost.     

Ambient-condition growth of superconducting YBa2Cu4O8 single crystals using KOH flux

YBa₂Cu₄O₈ is a stoichiometric oxide superconductor of T_c80 K. Unlike YBa₂Cu₃O_7−δ, this compound is free from oxygen vacancy or twin formation and does not have any microscopic disorder in the crystal. Doping with Ca raises its T_c to 90 K. The compound is a promising superconductor for technological application. Up to now, single crystals have not been grown without using specialized apparatus with extremely high oxygen pressure up to 3000 bar and at over 1100 °C due to the limited range of reaction kinetics of the compound. This fact has delayed the progress in the study of its physical properties and potential applications. We present here a simple growth method using KOH as flux that acts effectively for obtaining high-quality single crystals in air/oxygen at the temperature as low as 550 °C. As-grown crystals can readily be separated from the flux and exhibit a perfect orthorhombic morphology with sizes up to 0.7×0.4×0.2 mm³. Our results are reproducible and suggest that the crystals can be grown using a conventional flux method under ambient condition.     

Selective-controlled synthesis of one-dimensional strontium phosphates

Anorthic SrHPO₄ nanobelts and hexagonal Sr₁₀O(PO₄)₆ nanorods were obtained by a simple hydrothermal method without adding any surfactant as template. The as-synthesized products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). TEM and HRTEM observations of the products revealed that the as-prepared SrHPO₄ nanobelts and Sr₁₀O(PO₄)₆ hexagonal nanorods are single crystals with their preferential growth direction along the normal of (1 0 0) and (0 0 1) planes, respectively.     

Precipitation of In2O3 nano-crystallites from glasses in the system Na2O/B2O3/Al2O3/In2O3

Glasses in the system Na₂O/B₂O₃/Al₂O₃/In₂O₃ were melted and subsequently tempered in the range from 500 to 700 °C. Depending on the chemical composition, various crystalline phases were observed. From samples without Al₂O₃, In₂O₃ could not be crystallized from homogeneous glasses, because either spontaneous In₂O₃ crystallization occurred during cooling, or other phases such as NaInO₂ were formed during tempering. The addition of alumina, however, controlled the crystallization of In₂O₃. Depending on the crystallization temperature applied, the crystallite sizes were in the range from 13 to 53 nm. The glass matrix can be dissolved by soaking the powdered glass in water. This procedure can be used to prepare nano-crystalline In₂O₃-powders.     

Crystallization of In2O3 by vapor reaction

Crystallization of In₂O₃ occured in closed porcelain crucibles in air at 960–1200°C by vapor phase reaction of In₂O or In vapor with the oxygen diffusing into the system. The In₂O or In vapors were thermally generated from mixtures such as graphite/In₂O₃, graphite/In, In₂O₃/In and graphite/In₂O₃/In. The graphite/In₂O₃ system at a mole ratio of 30/1 and 1000°C produced yellow, transparent needle crystals with a maximum size of 0.5 X 0.5 X 8 mm and electrical resistivity of 5.5 X 10^-2 ω cm at 25°C.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.     

Epitaxial growth of the CoFe2O4 film on SrTiO3 and its characterization

Cobalt ferrite (CoFe₂O₄) thin film is epitaxially grown on (0 0 1) SrTiO₃ (STO) by laser molecular beam epitaxy (LMBE). The growth modes of CoFe₂O₄ (CFO) film are found to be sensitive to laser repetition, the transitions from layer-by-layer mode to Stranski–Krastanov (SK) mode and then to island mode occur at the laser repetition of 3 and 5 Hz at 700 °C, respectively. The X-ray diffraction (XRD) results show that the CFO film on (0 0 1) SrTiO₃ is compressively strained by the underlying substrate and exhibits high crystallinity with a full-width at half-maximum of 0.86°. Microstructural studies indicate that the as-deposited CFO film is c-oriented island structure with rough surface morphology and the magnetic measurements reveal that the compressive strained CoFe₂O₄ film exhibits an enhanced out-of-plane magnetization (190 emu/cm³) with a large coercivity (3.8 kOe).     

Bi20TiO32 nanocones prepared from Bi–Ti–O mixture by metalorganic decomposition method

Bi₂₀TiO₃₂ in the form of nanocones are reported for the first time, which have been found during the formation of Bi₂Ti₂O₇ nanocrystals. Bi₂₀TiO₃₂ nanocones were prepared by metalorganic decomposition technique. From X-ray patterns, it was found that Bi₂₀TiO₃₂ is a metastable phase, and can transform gradually into Bi₂Ti₂O₇ phase with the annealing time increasing at a temperature of 550°C. The image of field emission scanning electron microscopy shows that the lengths of the nanocones are up to several micrometers and the diameters of cusps range from 20 to 200 nm. The studies of transmission electron microscopy show that the nanocones are crystalline Bi₂₀TiO₃₂. The growth mechanism of Bi₂₀TiO₃₂ nanocones has been proposed, which is similar to the vapor–liquid–solid growth mechanism.     

Growth and morphology of ruby crystals with unusual chromium concentration

Single crystals of ruby have been obtained from fluxed melts based on the systems Li₂O–MoO₃, Li₂O–WO₃, Na₂O–WO₃, 2PbO–3V₂O₅, PbO–V₂O₅–WO₃, PbF₂–Bi₂O₃ and Na₃AlF₆ by both the TSSG method and spontaneous crystallization at the temperatures 1330–900 °C. Al₂O₃ solubility has been measured for the flux composition of 2Bi₂O₃–5PbF₂ in the temperature range 1200–1000 °C and dissolution enthalpy has been defined as 29.4 KJ/Mol. The composition of grown crystals was studied by electron microprobe analysis. The synthetic ruby contains from 0.51 to 6.38 at% of chromium admixture depending on the crystal growth conditions. Experimental results on growth conditions, composition and morphology of grown crystals are presented for each flux and temperature interval.     

Solvothermal growth of ZnO

The growth of ZnO single crystals and crystalline films by solvothermal techniques is reviewed. Largest ZnO crystals of 3 inch in diameter are grown by a high-pressure medium-temperature hydrothermal process employing alkaline-metal mineralizer for solubility enhancement. Structural, thermal, optical and electrical properties, impurities and annealing effects as well as machining are discussed. Poly- and single-crystalline ZnO films are fabricated from aqueous and non-aqueous solutions on a variety of substrates like glass, (100) silicon, -Al₂O₃, Mg₂AlO₄, ScAlMgO₄, ZnO and even some plastics at temperatures as low as 50 °C and ambient air conditions. Film thickness from a few nanometers up to some tens of micrometers is achieved. Lateral epitaxial overgrowth of thick ZnO films on Mg₂AlO₄ from aqueous solution at 90 °C was recently developed. The best crystallinity with a full-width half-maximum from the (0002) reflection of 26 arcsec has been obtained by liquid phase epitaxy employing alkaline-metal chlorides as solvent. Doping behavior (Cu, Ga, In, Ge) and the formation of solid solutions with MgO and CdO are reported. Photoluminescence and radioluminescence are discussed.     

Flux growth of BPO4 crystals

Single crystals of BPO₄ with sizes up to 15×10×12 mm³ were grown by top-seeded solution growth method using Li₂O–Li₄P₂O₇ as fluxes. The components volatilized from the melt were characterized by the method of X-ray powder diffraction. The defects of grown crystals have also been investigated. The measured ultraviolet cutoff edge of BPO₄ was about 130 nm. Its density was 2.82 g/cm³ determined using drainage method.     

Crystallization behavior and hydrophilic performances of V2O5–TiO2 films prepared by sol–gel dip-coating

Homogeneous and transparent V₂O₅–TiO₂ composite nanometer thin films were prepared on glass substrates by sol–gel processing and dip-coating technique. The films as well as the dried powder of bulk gel were characterized by different techniques like X-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM), atomic force microscope (AFM) and thermogravimetry–differential thermal analysis (TG–DTA). The hydrophilicity of the films was determined by measuring the water contact angles on the films. The results showed that the dopant of V₂O₅ on TiO₂ thin films could produce a visible-light response to the films, and the introduction of V₂O₅ could suppress the structural phase transition and crystal growth of TiO₂ crystal. Finally, the relationship between crystalline size and hydrophilicity under sunlight was investigated in this article.     

Growth of SrFe12O19 nanowires under an induced magnetic field

Nanowires of SrFe₁₂O₁₉ with diameters of 100 nm and lengths of 2.5 μm have been successfully synthesized in a hydrothermal cell at 180 °C with an 0.35 T magnetic field applied. The growth behavior of the nanoparticles was compared with that under zero magnetic field. The X-ray diffraction patterns indicate that both of the two processes result in formation of pure SrFe₁₂O₁₉, however transmission electron microscope observations show that the morphology of the particles changed from flake-like in zero magnetic field into nanowires in a magnetic field. Compared to the sample obtained under zero magnetic field, the as-prepared one exhibits a higher saturation magnetization. The possible underlying mechanism responsible for the morphology change and the magnetic properties improvement were discussed.     

Facile synthesis of submicron BaTiO3 crystallites by a liquid–solid reaction method

Uniform, submicron BaTiO₃ crystallites in tetragonal structure were synthesized by a novel low-temperature liquid–solid reaction method mainly via two simple steps: firstly, BaO₂·H₂O₂ submicron particles of about 130–450 nm were precipitated from the reaction of BaCl₂ and H₂O₂ in a slightly alkaline (pH 8) aqueous solution under the ambient condition; secondly, tetragonal phase BaTiO₃ submicrocrystals with the size in the range of 180 to 400 nm could be produced by subjecting the as-prepared BaO₂·H₂O₂ and commercial TiO₂ submicron particles to thermal treatment in air at 700 °C for 10 h. The as-obtained products were characterized by X-ray powder diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and inductively coupled plasma-atomic emission spectroscopy, and scanning electron microscopy.     

Controlled synthesis of different morphologies of BaWO4 crystals via a surfactant-assisted method

BaWO₄ crystals with different morphologies, such as nanosheets, nanobelts, flower-like, quadrangled plates and sheaves of dendrite, have been successfully synthesized via PVP as templates. Our result shows that reaction parameters, such as the concentration of PVP aqueous solutions, pH value of the starting solution and molar ratio of [Ba²⁺]/[WO₄²⁻] played important roles in the formation of BaWO₄ crystal with different morphologies. It is obviously different between microwave irradiation heating and oil bath heating. The products were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and electron diffraction.