退火效应对MOCVD生长的ZnO薄膜的影响

我们利用MOCVD设备在α-Al2O3衬底上生长了c轴取向的ZnO薄膜,通过X射线衍射(XRD)、光致发光谱(PL)对ZnO薄膜进行表征,研究了退火对ZnO薄膜光电特性影响.通过退火优化, ZnO薄膜的结晶性得到提高,晶粒尺寸变大,紫外光发射峰的强度相对变强.     

退火温度对6H-SiC衬底上ZnO薄膜发光性质的影响

采用溶胶-凝胶方法,在6H-SiC衬底上制备ZnO薄膜.X射线衍射结果表明薄膜是c轴取向的,具有六方纤锌矿多晶结构.研究了退火温度对ZnO薄膜发光特性的影响.发现在650℃退火温度下,观察到近带边紫外发射和可见光发射并且紫外发光强度大于可见光发射.随着退火温度的提高,紫外峰强度减弱直至消失,而绿光发射强度先增加而后降低.对退火温度引起ZnO薄膜发光性质改变的机制进行了探讨.     

退火对Si(111)衬底上ZnO薄膜的结构和发光特性的影响

采用磁控溅射法在硅(111)衬底上制备了C轴高度取向的ZnO薄膜,并研究了退火温度和氧气气氛对ZnO薄膜晶体质量、晶粒度大小和光致发光谱的影响.X射线衍射表明,所有薄膜均为高度C轴择优取向,当退火温度低于900℃时,随着退火温度的升高,薄膜的取向性和结晶度都明显提高.室温下对ZnO薄膜进行了光谱分析,退火后的样品均可观测到明显的紫光发射.在一定的退火温度范围内,还可以观测到明显的紫外双峰.空气中退火的样品,当退火温度达到或高于600℃还可观测到绿光发射.实验结果表明,发光峰强度随退火温度和氧气气氛不同而不同,通过改变退火时的温度和氧气气氛可以改变ZnO薄膜的微结构和发光性质.     

碱金属掺杂ZnO薄膜发光性能研究

采用固相反应法制备了不同比例的碱金属掺杂ZnO靶材,并利用磁控溅射法在Si(111)基片上制备不同温度下生长的c轴择优取向ZnO薄膜.通过XRD、AFM和荧光光谱(PL谱)研究了掺杂元素和掺杂比例对薄膜结构和发光特性的影响.结果表明,掺杂未改变ZnO的结构,薄膜具有很好的c轴择优取向.室温下用325 nm的氙灯作为激发光源得到不同样品的 PL 谱,分析表明,紫外发光峰来源于自由激子的复合辐射与带间跃迁,蓝绿发光峰与锌缺陷和氧缺陷有关.此外还探讨了紫外发光峰红移的可能机理.     

Si(111)衬底上ZnO薄膜的磁控溅射法制备及表征

采用磁控溅射法在(111)单晶硅衬底上沉积了ZnO薄膜,并研究了退火温度对ZnO薄膜晶体质量、晶粒度大小、应力和光致发光谱的影响.X射线衍射(XRD)表明薄膜为高度c轴择优取向.不同退火温度下的ZnO薄膜应力有明显变化,应力分布最为均匀的退火温度为500℃.室温下对ZnO薄膜进行了光谱分析,可观测到明显的紫光发射(波长为380nm左右).实验结果表明,用磁控溅射法在单晶硅衬底上能获得高质量的ZnO薄膜.     

热处理蓝宝石基片对Tl-2212超导薄膜的影响

本文研究了蓝宝石基片的热处理对Tl-2212薄膜的结晶质量、表面形貌及其超导特性的影响.SEM和XRD研究表明,在经过最佳条件(1000 ℃×20 h)退火后的基片上,可以制作出具有致密的晶体结构、高度c轴取向的外延Tl-2212超导薄膜,其薄膜具有优良的电学性能.     

溶胶-凝胶法制备纳米ZnO薄膜及其光催化性能

本文采用溶胶-凝胶法在石英玻璃基底上制备出性能优良的ZnO薄膜,并通过XRD和UV-VIS吸收光谱对薄膜的结构及光吸收特性进行表征,进一步研究了退火温度和氧气流量对ZnO薄膜光催化性能的影响.结果表明,本实验中ZnO薄膜光催化降解苯酚的最佳条件是:退火温度在300℃,氧气流量为20ml/min,催化效果显著.     

氩氧比对磁控溅射ZnO薄膜的压电响应与极化特性的影响

保持总的工作气压不变,在不同氩氧比条件下,采用射频磁控溅射法在铝电极层上制备了ZnO薄膜.用X射线衍射(XRD)、原子力显微镜(AFM)和压电响应力显微镜(PFM)分析了ZnO薄膜的择优取向、表面形貌和压电响应,并通过垂直PFM(VPFM)和水平PFM(LPFM)相位图研究了ZnO晶粒的极化特性.结果表明,氩氧比对ZnO薄膜的晶体结构和压电特性有显著影响,其中在氩氧比1∶1的条件下制备的ZnO薄膜具有最大的VPFM振幅和最佳的极化取向一致性.     

射频反应磁控溅射制备ZnO薄膜的微结构及其光学性能

采用射频反应磁控溅射技术在石英和Si衬底上制备了高度c轴择优取向的ZnO薄膜,样品的氧氩流量比分别为10:40,20:40,30:40,40:40.利用X射线衍射仪、表面轮廓仪、原子力显微镜和紫外-可见分光光度计研究了样品的微结构与光学特性.研究表明:氧氩流量比为30:40的样品结晶质量最好.所制备的ZnO薄膜的可见光平均透射率均大于87;.随着氧氩流量比的增大,薄膜的透射率呈非单调变化,氧氩流量比为30:40的样品在可见光范围的平均透射率可达93;.光学带隙随着氧氩流量比的增大,先增大后减小.与块材ZnO的带隙(3.37 eV)相比,ZnO薄膜的带隙均变窄.     

热处理工艺对室温制备ZnO:Al薄膜结构与光电性能的影响

采用室温溅射加后续退火工艺制备了ZnO∶ Al透明导电薄膜.研究了热处理工艺对薄膜微观结构和光电性能的影响.研究表明:退火有助于减小Al~(3+)对Zn~(2+)的取代造成的晶格畸变,消除应力,促进晶粒长大,有效提高电子浓度和迁移率,降低电阻率;当溅射功率为80 W、退火温度为320 ℃时,薄膜的电阻率可低至8.6×10~(-4) Ω·cm;退火气氛对薄膜的导电性能有较大影响,真空退火可使吸附氧脱附,大大降低薄膜的方块电阻.而退火温度和退火气氛均对ZnO∶ Al薄膜的透光率没有明显影响,薄膜的透光率在86;以上.     

A review of measurement of thermophysical properties of silicon melt

Measurements of thermophysical properties of Si melt and supplementary study of X-ray scattering/diffraction by the authors' group were reviewed. The values obtained differed variously from those of literature. Density was 2–3% larger, surface tension 20–30% smaller, viscosity up to 40% larger, electrical conductivity 8% smaller, spectral emissivity more or less in good agreement with literature values, and thermal diffusivity a few percent larger. An anomalous density jump was found near the melting point. Surface tension and viscosity also showed anomaly. A strange time-dependent change of density was observed over 3 h after melting. X-ray analyses suggested a slight change in local atom ordering, but showed no sign of cluster formation. An addition of 0.1 at% gallium caused the density jump to disappear, while that of boron caused no change. An EXAFS study of the former melt indicated a strong interaction between Ga and Si atoms as if molecules of GaSi₃ existed. The implications of the measured properties are a possibility of soft-turbulence in an Si melt in a relatively large crucible, a more complicated manner of intake of oxygen depleted molten Si from the free surface region to underneath the growing crystal, and a relaxation of the melt after melting arising from trapped gas species.     

电子显微分析在表征纳米晶体化学组分中的应用

纳米材料的化学组分及含量影响其光、电、声、热、磁等物理性能,电子显微分析是表征纳米晶体化学组分的重要方法之一.本文综述了X-射线能谱(EDS)、X-射线波谱(WDS)、电子能量损失谱(EELS)和选区电子衍射(SAED)等现代电子显微分析技术在表征纳米晶体化学组分、形貌、尺寸和结构等方面的应用及其研究进展,并比较了这些分析方法存在的差异,提出了其应用中存在的不足及今后的研发方向.     

Mesomorphism Dependence on the Position of Substitution of a Pair of Esters

A novel homologous series of ethylene derivatives of thermotropic liquid crystals has been synthesized. The methoxy to octyloxy derivatives are nematogenic, the decyloxy to tetradecyloxy derivatives are smectogenic, in addition to nematogenic, and the hexadecyloxy homologue is smectogenic only. All the members of the series are enantiotropically mesogenic. Thermotropic behavior was determined by an optical polarizing microscope equipped with a heating stage and Differential Scanning Calorimetry (DSC) study. Analytical and spectral data confirm the molecular structures of homologues (infrared, nuclear magnetic resonance, mass spectra, X-ray, and DSC data). Textures of the nematic phase are threaded or Schlieren and that of smectic phase are focal conic fan-shaped of smectic A or C. Transition curves of the phase diagram behave in a normal manner except one or two deviations from the normal trend. The mesophase range (Sm+N) varies from 3°C to 44°C. The average thermal stability for smectic is 93°C and that for nematic 117.4°C. The LC behavior of the novel series is compared with a structurally similar known series.     

原位氮化法制备TiN纳米粉体

用溶胶凝胶法合成的纳米TiO2粉体作为原料,将该粉体在氨气中进行原位氮化制备了TiN纳米粉体.用XRD,TEM,化学分析等手段对合成的TiN纳米粉体的物相组成、形貌、成分进行了分析.实验分析表明:在1000℃和1100℃下分别氮化5h,可以制备粒径大约为40nm和80nm的TiN粉体,其TiN的含量分别为95.40;和98.37;;而在1000℃条件下氮化时间减少到2h时,TiN的含量仅为58.36;.氮化温度和氮化时间是合成纳米TiN的重要因素,提高合成温度和延长氮化时间均可形成纯度较高的TiN纳米粉体,但延长氮化时间更有利于获得粒径小的氮化钛粉体.     

On the influence of structural features of DNA on the possibility of metabolic transfer of electrons

Abstract

A fragment of a DNA molecule is considered as one of the channels of metabolic electron transfer. The heterogeneity of the complementary chains is effectively taken into account. This made it possible to find the speed of the electron injected into the DNA conduction band and the current density that it creates. Estimates of electron mobility in nucleic acid chains are made. They were an order of magnitude smaller than that of typical semiconductors. For the specific conductivity of nucleic acid chains, estimates provide a conductivity of one to two orders of magnitude lower than in graphite.     

PEG聚合度对氧化铝造粒粉的性能影响

为制备适用于干压成型的氧化铝造粒粉,研究了PEG聚合度对氧化铝造粒粉微观形貌、流动性和松装密度的影响.结果表明PEG的聚合度对氧化铝浆料粘度影响显著,PEG2000-6000是较为理想的粘结剂选择,造粒粉的流动性与环境温度及湿度相关.采用正交实验设计,以造粒粉的流动性和松装密度为评价指标,对PEG聚合度、粘结剂添加量和固含量进行了优选,其影响顺序为PEG聚合度＞固含量＞粘结剂添加量.以优选参数PEG6000、添加量为4wt;、固含量为80wt;,制备了性能优良的氧化铝喷雾造粒粉.     

Effect of alumina on enthalpy of mixing of mixed alkali silicate glasses

The enthalpy of mixing of mixed alkali (Na₂O and K₂O) silicate glasses containing various concentrations of alumina was determined using an ion-exchange equilibrium method. For glasses with a constant alkali concentration, the enthalpy of mixing was found to become less negative with alumina addition. Consistent with our previous results on the enthalpy of mixing of alumina-free mixed alkali silicate glasses, the magnitude of enthalpy of mixing exhibited a good correlation with the molar volume mismatch of the corresponding two single alkali glasses as well as with the extent of conductivity mixed alkali effect, e.g. excess activation energy of conductivity, ΔE. The reduction of the magnitude of the enthalpy of mixing with alumina addition can be attributed to the reduction of non-bridging oxygen and ionic field strength. Combining the present results with results obtained earlier, the magnitude of the enthalpy of mixing for all mixed alkali (Na₂O and K₂O) silicate glasses with and without alumina was expressed by a simple function of a modified Tobolsky parameter, which takes into account the alkali concentration and the difference in cation-to-effective anion distances. The enthalpy of mixing data of the mixed alkali glasses was then compared with reported experimental data on the conductivity of mixed alkali aluminosilicate glasses. What appears to be conflicting experimental data can be understood in terms of the magnitude of the enthalpy of mixing and we can conclude that the mixed alkali effect is closely correlated with the negative enthalpy of mixing.     

近化学计量比铌酸锂晶体组分测定与缺陷观察

采用助熔剂提拉法生长得到近化学计量比LiNbO3晶体.用多种方法测定了晶体组分,结果表明生长得到的晶体中[Li2O]含量为49.80;摩尔分数;对晶体缺陷的研究表明晶体质量有待提高,并分析了晶体中出现包裹物的原因.     

Statistical characterization of the pore space of random systems of hard spheres

An improved statistical characterization of disordered structures such as metallic glasses, random porous media, or granular matter is presented. Suitable structure models follow the idea of dense random packed spheres, where the spheres represent atoms and particles in the case of metallic glasses and porous or granular matter, respectively. The geometry of the empty space between the atoms or particles is described by means of the already otherwise successful concept of so-called contact distributions. Their exact mathematical forms are unknown for hard sphere systems. Knowledge on these is obtained by means of Monte Carlo simulations of the structure models. The numerical results are approximated by simple and general mathematical expressions, with parameters that can be easily determined. These may serve as additional tools for the structural characterization of disordered matter, including systems of partly penetrable spheres.     

前驱物合成条件对锰锌铁氧体结构和性能的影响

采用共沉淀-热处理工艺合成了尖晶石型锰锌铁氧体粉末,利用正交试验优化了制备工艺。利用X射线衍射仪(XRD)扫描电子显微镜(SEM)和振动样品磁强计(VSM)对粉体的显微结构和静磁性能进行了研究。结果表明:热处理温度为1350℃、保温时间为3.5 h、进料比为1.5时,若前驱物的pH值为6,制备的样品的主晶相为锰锌铁氧体;若前驱物的pH值为7 9,则形成单相尖晶石型锰锌铁氧体,样品的饱和磁化强度先增大后减小,矫顽力逐渐增大。pH值为7时,配方为Fe∶Mn∶Zn=68.4816∶17.1368∶14.381,进料比为1.5,滴加时间为40 min,反应温度为50℃,不加表面活性剂时得到的样品具有较高的饱和磁化强度。