Precipitation of In2O3 nano-crystallites from glasses in the system Na2O/B2O3/Al2O3/In2O3

Glasses in the system Na₂O/B₂O₃/Al₂O₃/In₂O₃ were melted and subsequently tempered in the range from 500 to 700 °C. Depending on the chemical composition, various crystalline phases were observed. From samples without Al₂O₃, In₂O₃ could not be crystallized from homogeneous glasses, because either spontaneous In₂O₃ crystallization occurred during cooling, or other phases such as NaInO₂ were formed during tempering. The addition of alumina, however, controlled the crystallization of In₂O₃. Depending on the crystallization temperature applied, the crystallite sizes were in the range from 13 to 53 nm. The glass matrix can be dissolved by soaking the powdered glass in water. This procedure can be used to prepare nano-crystalline In₂O₃-powders.     

B NMR investigations in xV2O5–B2O3 and xV2O5–B2O3–PbO glasses

11B (I=3/2) MAS NMR in the binary glass system xV₂O₅–B₂O₃ (x=0.053, 0.43) and the ternary glass system xV₂O₅–B₂O₃–PbO (0.1x1.5) has been investigated at room temperature. In the xV₂O₅–B₂O₃ glasses, one NMR line due to BO₃ unit was observed. Meanwhile in the xV₂O₅–B₂O₃–PbO, two NMR lines which arise from BO₃ and BO₄ units were detected, where the appearance of BO₄ units is produced by the presence of PbO. From the computer-simulation of the ¹¹B NMR central transition line (m=−1/2↔1/2), the quadrupole parameters (e²qQ/h and η) for BO₃ units in xV₂O₅–B₂O₃, and those for BO₃ and BO₄ units in xV₂O₅–B₂O₃–PbO were obtained as a function of x. As the V₂O₅ content increases in xV₂O₅–B₂O₃–PbO, the e²qQ/h and η values of the BO₃⁻ associated resonance are found to slightly decrease and increase, respectively. Meanwhile, the e²qQ/h and η values of BO₄⁻ associated resonance in xV₂O₅–B₂O₃–PbO are found to slightly increase and decrease, respectively. By comparing the intensities of the total transitions (m=−3/2↔−1/2,m=−1/2↔1/2, and 1/2↔3/2) for the ¹¹B NMR line of BO₃ and BO₄ units contained in xV₂O₅–B₂O₃–PbO with those of respective standard samples of 0.053V₂O₅–B₂O₃ and NaBH₄, the quantitative fractions of BO₃ and BO₄ in xV₂O₅–B₂O₃–PbO were obtained as a function of x.     

Study of electrical properties of MoO3–Fe2O3–P2O5 and SrO–Fe2O3–P2O5 glasses by impedance spectroscopy. II

The electrical and dielectric properties for three series of MoO₃–Fe₂O₃–P₂O₅ and one series of SrO–Fe₂O₃–P₂O₅ glasses were measured by impedance spectroscopy in the frequency range from 0.01 Hz to 3 MHz and over the temperature range from 303 to 473 K. It was shown in Part I that the MoO₃ is incorporated into phosphate network and the structure/properties are strongly influenced by the overall O/P ratio. The Fe₂O₃ content and Fe(II)/Fe_tot ratio in these glasses have significant effects on the electrical conductivity and dielectric permittivity. With decreasing Fe₂O₃ content in MoO₃–Fe₂O₃–P₂O₅ glasses with O/P at 3.5 the dc conductivity, σ_dc(ω) decreases for two orders of magnitude, which indicates that the conductivity for these glasses depends on Fe₂O₃ and is independent of the MoO₃ content. Also, the dielectric properties such as ^′(ω), ^″(ω) and σ_ac(ω) and their variation with frequency and temperature indicates a decrease in relaxation intensity with increase in the concentration of MoO₃. On the other hand, the dc conductivity for MoO₃–Fe₂O₃–P₂O₅ glasses with O/P > 3.5 increases with the substitution of MoO₃ which has been explained by an increase in the number of non-bridging oxygens and formation of Fe–O–P bonds that are responsible for formation of small polarons. The increase in the dielectric permittivity, ^′(ω) with increasing MoO₃ content is attributed to the increase in the deformation of glass network with increasing bonding defects. For SrO–Fe₂O₃–P₂O₅ glasses the conductivity and dielectric permittivity remained constant with increasing SrO.     

Glass formation, properties and structure of glasses in the P2O5---WO3---K2O---Al2O3 system

Glass formation in the P₂O₅---WO₃---K₂O---Al₂O₃ system was investigated and the glass-forming regions are presented.

the properties of the glasses in the P₂O₅---WO₃---K₂O---Al₂O₃ system (Al₂O₃ 8 mol.%) are reported.

The colouration of glass was studied. It was found that W⁵⁺ ions make glass blue.

Infrared spectra were measured by means of making KBr pills. Results of the investigation suggest that P---O---P, P---O---W, and W---O---W bonds form a continuous network in the phosphate glasses. So we suggest that tungsten trioxide is a glass former.     

Effect of Al2O3 on phase separation and crystallization in ZnO---Al2O3---B2O3---SiO2 glasses

The effect of alumina on the phase separation and the crystallization of the glasses of composition (mol%) 18ZnO·30B₂O₃·52SiO₂ and O-40 Al₂O₃ was studied using an electron microscope and IR spectroscopy. The main crystalline phase appears in the microphase for which the compositions are not nearer to the crystal stoichiometry than the mean. The addition of Al₂O₃ suppresses the immiscibility but enhances the crystallizability.     

Some characteristics of glass in the Al2O3---B2O3---SiO2 system from the gel

The colorless and transparent glasses in the Al₂O₃---B₂O₃---SiO₃ system with high B₂O₃ and SiO₂ content were prepared from gels at low temperature. Their IR spectra not only revealed the evolution of the gel to glass conversion, but also showed that the formation of mixed bonds in the glasses obtained did not show any effect due to the B₂O₃ content. The accuracy of the glass composition is dependent upon the SiO₂/B₂O₃ molar ratio. The higher the ratio, the less the deviation of the analyzed compositions of the resulting glasses from their original calculated values. It is obvious that the higher the ratio, the lower the thermal expansion coefficient and the higher the transformation temperature of the glass, and the temperature at which the thermal contraction reaches an equilibrium is higher.     

Crystallization of In2O3 by vapor reaction

Crystallization of In₂O₃ occured in closed porcelain crucibles in air at 960–1200°C by vapor phase reaction of In₂O or In vapor with the oxygen diffusing into the system. The In₂O or In vapors were thermally generated from mixtures such as graphite/In₂O₃, graphite/In, In₂O₃/In and graphite/In₂O₃/In. The graphite/In₂O₃ system at a mole ratio of 30/1 and 1000°C produced yellow, transparent needle crystals with a maximum size of 0.5 X 0.5 X 8 mm and electrical resistivity of 5.5 X 10^-2 ω cm at 25°C.     

An X-ray diffraction study of the structure of B2O3---Cs2O liquids

The short range structures of B₂O₃ (90 mol%)---Cs₂O (10 mol%) and B₂O₃ (80 mol%)---Cs₂O (20 mol%) liquids were analyzed at 973 and 1053 K, respectively, by an X-ray diffraction method, and the effects of Cs₂O addition on the boron-oxygen bonding were investigated. The existence of BO₃ triangles, which form the so-called boroxol ring structure, was confirmed in B₂O₃---Cs₂O liquids, as well as in B₂O₃ liquid, but some fraction of the BO₃ triangles was thought to be converted to BO₄ tetrahedra. Similar results have previously been observed also in B₂O₃---Cs₂O glasses. A Cs atom was found to be surrounded by six O atoms; four Cs---O interatomic distances were about 3.2 Å but the other two were at 3.8–3.9 Å. These distances indicate that distorted Cs---O octahedra may exist in these B₂O₃---Cs₂O liquids.     

Raman spectrum studies of the glasses in the system Na2O---Al2O3---P2O5

Raman spectra of ternary sodium aluminosphosphate glasses indicate that for glasses with Al₂O₃/P₂O₅<0.63, the glass network is mainly built up of (PO₃)_n^n- chains and rings or different kinds of phosphate groups and AlO₄ tetrahedra; for glasses with Al₂O₃/P₂O₅>0.63, the glass network is mainly built up of AlPO₄ groups.     

Crystal growth of NdAl3(BO3)4 from K2O/MoO3/Nd2O3/B2O3/KF flux

NdAl₃(BO₃)₄ single crystals were grown by the flux method and the TSSG technique using a K₂O/3MoO₃/B₂O₃/0.5Nd₂O₃/KF flux system. Light-violet clear crystals could be obtained. The effects of fluoride on the growth of NAB crystals were investigated. As the content of KF was gradually increased, the growth form of NAB was changed from the equant to the columnar and the primary crystalline region of NAB was shrinked. At the ratio of KF/K₂O = 0.75, NAB crystals could not be grown.     

NMR studies of Na2O---B2O3---SiO2 glasses of mid-alkali content

¹¹B Fourier transform spectra have been used to study the structure of Na₂O---B₂O₃---SiO₂ glasses of mid-alkali content. Based on the measurements of the fraction N₄ of four-coordinated borons, it has been found that for K = mol.% SiO₂/mol.% B₂O₃ 8 and R = mol.% Na₂O/mol.% B₂O₃ = 1, N₄ is obviously smaller than 1 rather than equal to 1 as assumed in the relevant literature. Only when R reaches a value appropriately greater than 1, can the case where N₄ = 1 occur. A structural model suggested in this paper can satisfactorily explain the fact.     

Viscosity and IR investigations in the Li2O---B2O3 system

The high viscosity in melts of the Li₂O---B₂O₃ system makes it very difficult to grow large crystals of lithium triborate. The viscosity and IR characteristics of molten li₂O---B₂O₃ system are reported in this paper. When the temperature increases the viscosity of li₂O---B₂O₃ system decreases and follows an Arrhenius-type relationship. With an increasing 13203 ratio in Li₂O---B₂O₃ melts, the viscosity rises gradually to a maximum with a composition Li₂O: 3.513203 then it falls rapidly. In order to find active agents to reduce the viscosity, Na₂O, NaCl, LiF, P205, M003, W03 etc oxides were added to Li₂O---B₂O₃ samples respectively and investigated using the orthogonal method. The experimental results show that the addition of acidic oxides can significantly decrease the viscosity in the Li₂O---B₂O₃ system. For Li₂O: 4.513203, an ideal additive agent is 20wt% Li₂O:: 2MoO₃. Near the composition for crystal growth, the percentage reduction of viscosity is 62.2%. The IR spectra of Li₂O---B₂O₃ system revealed that the BO₄⁻/NO₃⁻ ratio is reduced in the melt using Li₂O: 2MoO₃ as an additive. It is proposed that the M003 reduced the concentration of bridging oxygen atoms of BO₄⁻. The change of structure explains the decline in the viscosity. In the crystal structures of lithium triborate, the matrix spaces are so small that larger other cations than Li+ are very difficult to enter the crystal matrix. So the use of additive agents to reduce the viscosity is a possible method if no new phase appears.     

Characterisation of semiconducting V2O5–Bi2O3–TeO2 glasses through ultrasonic measurements

Tellurite containing vanadate (50−x)V₂O₅–xBi₂O₃–50TeO₂ glasses with different bismuth (x=0, 5, 10, 15, 20 and 25 wt%) contents have been prepared by rapid quenching method. Ultrasonic velocities (both longitudinal and shear) and attenuation (for longitudinal waves only) measurements have been made using a transducer operated at the fundamental frequency of 5 MHz in the temperature range from 150 to 480 K. The elastic moduli, Debye temperature, and Poisson’s ratio have been obtained both as a function of temperature and Bi₂O₃ content. The room temperature study on ultrasonic velocities, attenuation, elastic moduli, Poisson’s ratio, Debye temperature and glass transition temperature show the absence of any anomalies with addition of Bi₂O₃ content. The observed results confirm that the addition of Bi₂O₃ modifier changes the rigid formula character of TeO₂ to a matrix of regular TeO₃ and ionic behaviour bonds (NBOs). A monotonic decrease in velocities and elastic moduli, and an increase in attenuation and acoustic loss as a function of temperature in all the glass samples reveal the loose packing structure, which is attributed to the instability of TeO₄ trigonal bipyramid units in the network as temperature increases. It is also inferred that the glasses with low Bi₂O₃ content are more stable than with high Bi₂O₃ content.     

Catalytic growth of In2O3 nanobelts by vapor transport

Indium oxide (In₂O₃) nanobelts have been fabricated by thermal evaporation of metallic indium powders with the assistance of Au catalysts. The as-synthesized nanobelts are single-crystalline In₂O₃ with cubic structure, and usually tens of nanometers in thickness, tens to hundreds of nanometers in width, and several hundreds of micrometers in length. The room temperature photoluminescence spectrum of In₂O₃ nanobelts features a broad emission band at 620 nm, which could be attributed to oxygen deficiencies in the as-synthesized belts. The formation of In₂O₃ nanobelts follows a catalyst-assistant vapor—liquid–-solid growth mechanism, which enables the controlled growth of individual belts on predetermined sites.     

Al2O3-TiO2 and Al2TiO5 ceramic materials by the sol-gel process

Ceramic materials with a very low thermal expansion coefficient are synthesized by the sol-gel process. The binary gel is obtained by hydrolysis and polycondensation reactions of organometallic compounds of aluminium and titanium. The thermal evolution of the amorphous powder is followed by DTA and TGA measurements. Structural evolution is followed using X-ray diffraction. The crystallization of the TiO₂ rutile and Al₂O₃ corindon starts at 700 and 900°C respectively. The transformation of Al₂O₃ and TiO₂ into Al₂TiO₅ appears between 1200 and 1300°C. The densification of the powder is performed by the hot pressing process. The shrinkage of the powder was previously followed by dilatometric measurements. The physical properties of the final material are studied as a function of pressing parameters.     

Optical absorption and elastic properties of Li2O---(LiCl)2---B2O3---Al2O3 glasses

Ultraviolet transmission, densities, and supersonic velocities of the Li₂O---(LiCl)₂---B₂O₃---Al₂O₃ glasses were measured. Adiabatic compressibilities of all these glasses were calculated. The results were interpreted from the viewpoint of the glass structure.     

Solvothermal synthesis of K2V3O8 nanorods

A solvothermal route has been developed to synthesize K₂V₃O₈ nanorods via the reduction of V₂O₅ using ethanol as the reducing agent as well as the solvent at 200°C. X-ray diffraction and selected area electron diffraction analysis revealed that the as-synthesized products are of tetragonal structure K₂V₃O₈. Transmission electron spectroscopy image showed that the obtained K₂V₃O₈ comprises rod-like nanocrystallites. The formation mechanism of K₂V₃O₈ was studied.     

Solidification of superalloy in a SiO2–ZrO2–B2O3 coating mould

The preparation of glass-lined coating mould from gels in the ternary system of SiO₂–ZrO₂–B₂O₃ has been investigated. The crystallization characterization and high temperature structure stability of this coating mould are demonstrated. We can find that the crystallization of t-ZrO₂ as well as the tetragonal to monoclinic phase transformation are, respectively, retarded and impeded owing to the encasement of SiO₂ matrix. While the inhibitive effect of B₂O₃ on crystallization of the SiO₂–ZrO₂–B₂O₃ coating mould is explained. Finally, DD3 single crystal superalloy melt can realize highly undercooled rapid solidification by adopting this coating mould, which further evinces that SiO₂–ZrO₂–B₂O₃ coating mould has an ideal nucleation inhibition for superalloy.     

Glass formation and crystallization in the ZrO2---Al2O3---P2O5 system

The glass formation of the ZrO₂---Al₂O₃---P₂O₅ system in the high phosphate region is determined. The crystallization process and the crystal types formed during heat treatment have been studied. The structure of these glasses is discussed.     

Hydrolytic resistance of Na2O---B2O3---SiO2 gels prepared by sol-gel process

Alkoxide derived gels were prepared in the system Na₂O---B₂O₃---SiO₂. The gel compositions were situated in the liquid-liquid immiscibility area of the phase equilibrium diagram.

Hydrolytic resistance tests were performed on the gels heat-treated at temperatures ranging between 120 to 850 °C. The Na₂O, B₂O₃ and SiO₂ extracted from the attack gels were analyzed. The experimental results indicate that the amount of B₂O₃ has a significant influence on the chemical durability of the heat-treated gels. At temperatures of 850 °C the greater the B₂O₃ mol% the greater are the amounts of Na₂O and B₂O₃ extracted. Different behaviour was observed for gels heat-treated at 600 °C where the amounts of B₂O₃ and Na₂O extracted slightly increases as the B₂O₃ mol% increases. Small amounts of extracted SiO₂ were always observed.

These results are complemented with other measurements so that an explanation of the controlling mechanism is given.