Si(111)衬底上ZnO薄膜的磁控溅射法制备及表征

采用磁控溅射法在(111)单晶硅衬底上沉积了ZnO薄膜,并研究了退火温度对ZnO薄膜晶体质量、晶粒度大小、应力和光致发光谱的影响.X射线衍射(XRD)表明薄膜为高度c轴择优取向.不同退火温度下的ZnO薄膜应力有明显变化,应力分布最为均匀的退火温度为500℃.室温下对ZnO薄膜进行了光谱分析,可观测到明显的紫光发射(波长为380nm左右).实验结果表明,用磁控溅射法在单晶硅衬底上能获得高质量的ZnO薄膜.     

Al-H共掺杂ZnO薄膜的形貌及光致发光性能研究

在不同衬底温度条件下采用RF磁控溅射法在石英玻璃上沉积Al-H共掺杂ZnO薄膜.对所有样品进行晶体结构、表面形貌、电学、光学以及室温光致发光性能分析.结果表明:随着衬底温度的升高,ZnO薄膜的结晶度增加,晶粒增大,薄膜致密度增加;薄膜表面起伏变化减小;同时,电阻率最低达到7.58×10-4Ω·cm,透过率保持在75;左右.所有ZnO薄膜样品都以本征发光为主,Al-H共掺杂在一定程度降低ZnO薄膜缺陷发光的强度;随着衬底温度的升高,ZnO薄膜的本征发光强度明显增大;同时在能量为3.45 eV附近观察到了一个紫外发光峰.     

Eu3+,Tb3+掺杂对RF磁控溅射ZnO薄膜结构的影响

利用RF磁控溅射技术,不同条件下在不同衬底上制备了纯ZnO及Eu3+,Tb3+共掺ZnO薄膜.研究了薄膜的衬底、沉积时间和衬底温度对ZnO薄膜结构及形貌的影响.使用X射线衍射仪(XRD)对样品的结构进行了表征,结果表明:玻璃和石英衬底上的薄膜分别在300℃、镀膜0.5h和常温下、镀膜lh时薄膜具有良好的c轴择优取向,单品质量较好;而硅衬底上的薄膜在300℃、镀膜lh时具有良好的(103)轴择优取向,单品质量略有降低.     

Al2O3衬底上生长ZnO薄膜的结构和光学特性

用脉冲激光沉积法在Al2O3(0001)衬底上沉积了ZnO薄膜.衬底温度分别为300℃、400℃、500℃、600℃和700℃.利用X射线衍射(XRD)和光致发光谱(PL)对薄膜的结构和光学性能进行研究.X射线衍射的结果表明在不同温度下生长的ZnO薄膜均具有高度c轴择优取向,衬底温度400℃时,膜的应力较小质量较高.ZnO薄膜有很强的紫外发光峰,紫外发光峰的强度与衬底温度密切相关,并发现当衬底温度从300℃增到400℃时,紫外发射峰出现6nm的蓝移.     

衬底温度对磁控溅射法制备掺Ta氧化锌薄膜性能的影响

采用射频磁控溅射法,在不同的衬底温度下制备了钽(Ta)掺杂的氧化锌(ZnO)薄膜,采用X射线能谱(EDS)、X射线衍射(XRD)、扫描电镜(SEM)、紫外-可见分光光度计和光致发光(PL)光谱研究了衬底温度对制备的Ta掺杂ZnO薄膜的组分、微观结构、形貌和光学特性的影响.EDS的检测结果表明,Ta元素成功掺入到了ZnO薄膜;XRD图谱表明,掺入的Ta杂质是替代式杂质,没有破坏ZnO的六方晶格结构,随着衬底温度的升高,(002)衍射峰的强度先增大后降低,在400℃时达到最大;SEM测试表明当衬底温度较高时(400℃和500℃),Ta掺杂ZnO薄膜的晶粒明显变大;紫外-可见透过光谱显示,在可见光范围,Ta掺杂ZnO薄膜的平均透光率均高于80;,衬底不加热时制备的Ta掺杂ZnO的透光率最高;制备的Ta掺杂ZnO薄膜的禁带宽度范围为3.34~3.37eV,衬底温度为500℃时制备的Ta掺杂ZnO薄膜的禁带宽度最小,为3.34eV.PL光谱表明衬底温度为500℃时制备的Ta掺杂ZnO薄膜中缺陷较多,这也是造成薄膜禁带宽度变小的原因.     

衬底温度对直流磁控溅射法制备掺锆氧化锌透明导电薄膜性能的影响

利用直流磁控溅射法在石英衬底上制备出了高透明导电的掺锆氧化锌(ZnO:Zr)薄膜.研究了衬底温度对ZnO:Zr薄膜结构、形貌及光电性能的影响.XRD表明实验中制备的ZnO:Zr为六方纤锌矿结构的多晶薄膜,具有垂直于衬底方向的c轴择优取向.实验所制备ZnO:Zr薄膜的晶化程度和导电性能对衬底温度有很强的依赖性.当衬底温度为300 ℃时, ZnO:Zr薄膜具有最小电阻率7.58×10-4 Ω·cm,其可见光平均透过率超过了91;.     

衬底温度对PLD方法制备的ZnO薄膜的光学和电学特性的影响

利用脉冲激光沉积法(PLD)在c面蓝宝石衬底上制备了ZnO薄膜并对其进行了X射线衍射(XRD)、反射式高能电子衍射(RHEED)、光致发光(PL)谱和霍尔(Hall)测试.RHEED和XRD分析表明,温度在350℃至550℃之间时,ZnO薄膜的结晶质量随着衬底温度的升高而提高,当衬底温度进一步升高后,ZnO薄膜的结晶质量开始下降.四个样品中,衬底温度为550℃的样品具有最清晰的规则点状RHEED图像和半高宽最窄的(0002)衍射峰.PL谱和Hall测量的结果表明,衬底温度为550℃的样品还具有最好的发光性质和最大的霍尔迁移率.     

衬底温度对直流反应磁控溅射法制备的N掺杂p型ZnO薄膜性能的影响

利用直流反应磁控溅射法(纯金属锌作为靶材,Ar-N2-O2混合气体作为溅射气体)在石英玻璃衬底上制备了N掺杂p型ZnO薄膜.通过XRD、Hall和紫外可见透射谱分别研究了衬底温度对ZnO薄膜结构性能、电学性能和光学性能的影响.XRD结果显示所有制备的薄膜都具有垂直于衬底的c轴择优取向,并且随着衬底温度的增加,薄膜的晶体质量得到了提高.Hall测试表明衬底温度对p型ZnO薄膜的电阻率具有较大影响,400℃下生长的p型ZnO薄膜由于具有较高的迁移率(1.32 cm2/Vs)和载流子浓度(5.58×1017cm-3),因此表现出了最小的电阻率(8.44Ω·cm).     

采用MOCVD方法在GaAs衬底上生长ZnO(002)和ZnO(100)薄膜

采用金属有机化学汽相沉积生长法（MOCVD），在不同的衬底表面处理条件和生长温度下，在GaAs衬底上生长出了ZnO薄膜。随着化学腐蚀条件的不同，可生长出优先定位不同的ZnO（100）和ZnO（002）薄膜。该薄膜的晶体结构特性是由X光衍射谱仪（XRD）所获得的，而其光学特性是由光荧光谱仪（PL）来测的。与ZnO（002）相比，ZnO（100）薄膜具有更优越的晶体结构特性，并且在同样的生长温度下都具有相似的光学特性。对于腐蚀条件不同的GaAs衬底所进行的XPS分析结果表明，ZnO薄膜优先定位变化的主要原因在于腐蚀过程中形成的富As层。     

不同衬底温度下ZnO外延薄膜的结构及光学特性分析

采用螺旋波等离子体辅助射频溅射沉积技术在Al2O3(0001)衬底上沉积ZnO外延薄膜,通过对其结构及光学性质的分析,探讨了衬底温度对薄膜生长特性的影响.实验结果表明,由于等离子体对反应气体的活化及载能粒子对表面反应的辅助作用,采用该等离子体辅助溅射技术能够在较低的衬底温度下实现较高质量的ZnO薄膜外延生长,然而,较高的衬底温度所引起的表面反应不利于薄膜中的氧空位及锌填隙等缺陷的减少,这将限制薄膜的外延质量及光学特性的进一步提高.     

A review of measurement of thermophysical properties of silicon melt

Measurements of thermophysical properties of Si melt and supplementary study of X-ray scattering/diffraction by the authors' group were reviewed. The values obtained differed variously from those of literature. Density was 2–3% larger, surface tension 20–30% smaller, viscosity up to 40% larger, electrical conductivity 8% smaller, spectral emissivity more or less in good agreement with literature values, and thermal diffusivity a few percent larger. An anomalous density jump was found near the melting point. Surface tension and viscosity also showed anomaly. A strange time-dependent change of density was observed over 3 h after melting. X-ray analyses suggested a slight change in local atom ordering, but showed no sign of cluster formation. An addition of 0.1 at% gallium caused the density jump to disappear, while that of boron caused no change. An EXAFS study of the former melt indicated a strong interaction between Ga and Si atoms as if molecules of GaSi₃ existed. The implications of the measured properties are a possibility of soft-turbulence in an Si melt in a relatively large crucible, a more complicated manner of intake of oxygen depleted molten Si from the free surface region to underneath the growing crystal, and a relaxation of the melt after melting arising from trapped gas species.     

电子显微分析在表征纳米晶体化学组分中的应用

纳米材料的化学组分及含量影响其光、电、声、热、磁等物理性能,电子显微分析是表征纳米晶体化学组分的重要方法之一.本文综述了X-射线能谱(EDS)、X-射线波谱(WDS)、电子能量损失谱(EELS)和选区电子衍射(SAED)等现代电子显微分析技术在表征纳米晶体化学组分、形貌、尺寸和结构等方面的应用及其研究进展,并比较了这些分析方法存在的差异,提出了其应用中存在的不足及今后的研发方向.     

原位氮化法制备TiN纳米粉体

用溶胶凝胶法合成的纳米TiO2粉体作为原料,将该粉体在氨气中进行原位氮化制备了TiN纳米粉体.用XRD,TEM,化学分析等手段对合成的TiN纳米粉体的物相组成、形貌、成分进行了分析.实验分析表明:在1000℃和1100℃下分别氮化5h,可以制备粒径大约为40nm和80nm的TiN粉体,其TiN的含量分别为95.40;和98.37;;而在1000℃条件下氮化时间减少到2h时,TiN的含量仅为58.36;.氮化温度和氮化时间是合成纳米TiN的重要因素,提高合成温度和延长氮化时间均可形成纯度较高的TiN纳米粉体,但延长氮化时间更有利于获得粒径小的氮化钛粉体.     

On the influence of structural features of DNA on the possibility of metabolic transfer of electrons

Abstract

A fragment of a DNA molecule is considered as one of the channels of metabolic electron transfer. The heterogeneity of the complementary chains is effectively taken into account. This made it possible to find the speed of the electron injected into the DNA conduction band and the current density that it creates. Estimates of electron mobility in nucleic acid chains are made. They were an order of magnitude smaller than that of typical semiconductors. For the specific conductivity of nucleic acid chains, estimates provide a conductivity of one to two orders of magnitude lower than in graphite.     

Mesomorphism Dependence on the Position of Substitution of a Pair of Esters

A novel homologous series of ethylene derivatives of thermotropic liquid crystals has been synthesized. The methoxy to octyloxy derivatives are nematogenic, the decyloxy to tetradecyloxy derivatives are smectogenic, in addition to nematogenic, and the hexadecyloxy homologue is smectogenic only. All the members of the series are enantiotropically mesogenic. Thermotropic behavior was determined by an optical polarizing microscope equipped with a heating stage and Differential Scanning Calorimetry (DSC) study. Analytical and spectral data confirm the molecular structures of homologues (infrared, nuclear magnetic resonance, mass spectra, X-ray, and DSC data). Textures of the nematic phase are threaded or Schlieren and that of smectic phase are focal conic fan-shaped of smectic A or C. Transition curves of the phase diagram behave in a normal manner except one or two deviations from the normal trend. The mesophase range (Sm+N) varies from 3°C to 44°C. The average thermal stability for smectic is 93°C and that for nematic 117.4°C. The LC behavior of the novel series is compared with a structurally similar known series.     

PEG聚合度对氧化铝造粒粉的性能影响

为制备适用于干压成型的氧化铝造粒粉,研究了PEG聚合度对氧化铝造粒粉微观形貌、流动性和松装密度的影响.结果表明PEG的聚合度对氧化铝浆料粘度影响显著,PEG2000-6000是较为理想的粘结剂选择,造粒粉的流动性与环境温度及湿度相关.采用正交实验设计,以造粒粉的流动性和松装密度为评价指标,对PEG聚合度、粘结剂添加量和固含量进行了优选,其影响顺序为PEG聚合度＞固含量＞粘结剂添加量.以优选参数PEG6000、添加量为4wt;、固含量为80wt;,制备了性能优良的氧化铝喷雾造粒粉.     

近化学计量比铌酸锂晶体组分测定与缺陷观察

采用助熔剂提拉法生长得到近化学计量比LiNbO3晶体.用多种方法测定了晶体组分,结果表明生长得到的晶体中[Li2O]含量为49.80;摩尔分数;对晶体缺陷的研究表明晶体质量有待提高,并分析了晶体中出现包裹物的原因.     

Statistical characterization of the pore space of random systems of hard spheres

An improved statistical characterization of disordered structures such as metallic glasses, random porous media, or granular matter is presented. Suitable structure models follow the idea of dense random packed spheres, where the spheres represent atoms and particles in the case of metallic glasses and porous or granular matter, respectively. The geometry of the empty space between the atoms or particles is described by means of the already otherwise successful concept of so-called contact distributions. Their exact mathematical forms are unknown for hard sphere systems. Knowledge on these is obtained by means of Monte Carlo simulations of the structure models. The numerical results are approximated by simple and general mathematical expressions, with parameters that can be easily determined. These may serve as additional tools for the structural characterization of disordered matter, including systems of partly penetrable spheres.     

前驱物合成条件对锰锌铁氧体结构和性能的影响

采用共沉淀-热处理工艺合成了尖晶石型锰锌铁氧体粉末,利用正交试验优化了制备工艺。利用X射线衍射仪(XRD)扫描电子显微镜(SEM)和振动样品磁强计(VSM)对粉体的显微结构和静磁性能进行了研究。结果表明:热处理温度为1350℃、保温时间为3.5 h、进料比为1.5时,若前驱物的pH值为6,制备的样品的主晶相为锰锌铁氧体;若前驱物的pH值为7 9,则形成单相尖晶石型锰锌铁氧体,样品的饱和磁化强度先增大后减小,矫顽力逐渐增大。pH值为7时,配方为Fe∶Mn∶Zn=68.4816∶17.1368∶14.381,进料比为1.5,滴加时间为40 min,反应温度为50℃,不加表面活性剂时得到的样品具有较高的饱和磁化强度。     

Effect of alumina on enthalpy of mixing of mixed alkali silicate glasses

The enthalpy of mixing of mixed alkali (Na₂O and K₂O) silicate glasses containing various concentrations of alumina was determined using an ion-exchange equilibrium method. For glasses with a constant alkali concentration, the enthalpy of mixing was found to become less negative with alumina addition. Consistent with our previous results on the enthalpy of mixing of alumina-free mixed alkali silicate glasses, the magnitude of enthalpy of mixing exhibited a good correlation with the molar volume mismatch of the corresponding two single alkali glasses as well as with the extent of conductivity mixed alkali effect, e.g. excess activation energy of conductivity, ΔE. The reduction of the magnitude of the enthalpy of mixing with alumina addition can be attributed to the reduction of non-bridging oxygen and ionic field strength. Combining the present results with results obtained earlier, the magnitude of the enthalpy of mixing for all mixed alkali (Na₂O and K₂O) silicate glasses with and without alumina was expressed by a simple function of a modified Tobolsky parameter, which takes into account the alkali concentration and the difference in cation-to-effective anion distances. The enthalpy of mixing data of the mixed alkali glasses was then compared with reported experimental data on the conductivity of mixed alkali aluminosilicate glasses. What appears to be conflicting experimental data can be understood in terms of the magnitude of the enthalpy of mixing and we can conclude that the mixed alkali effect is closely correlated with the negative enthalpy of mixing.