Al-H共掺杂ZnO薄膜的形貌及光致发光性能研究

在不同衬底温度条件下采用RF磁控溅射法在石英玻璃上沉积Al-H共掺杂ZnO薄膜.对所有样品进行晶体结构、表面形貌、电学、光学以及室温光致发光性能分析.结果表明:随着衬底温度的升高,ZnO薄膜的结晶度增加,晶粒增大,薄膜致密度增加;薄膜表面起伏变化减小;同时,电阻率最低达到7.58×10-4Ω·cm,透过率保持在75;左右.所有ZnO薄膜样品都以本征发光为主,Al-H共掺杂在一定程度降低ZnO薄膜缺陷发光的强度;随着衬底温度的升高,ZnO薄膜的本征发光强度明显增大;同时在能量为3.45 eV附近观察到了一个紫外发光峰.     

不同衬底温度下ZnO外延薄膜的结构及光学特性分析

采用螺旋波等离子体辅助射频溅射沉积技术在Al2O3(0001)衬底上沉积ZnO外延薄膜,通过对其结构及光学性质的分析,探讨了衬底温度对薄膜生长特性的影响.实验结果表明,由于等离子体对反应气体的活化及载能粒子对表面反应的辅助作用,采用该等离子体辅助溅射技术能够在较低的衬底温度下实现较高质量的ZnO薄膜外延生长,然而,较高的衬底温度所引起的表面反应不利于薄膜中的氧空位及锌填隙等缺陷的减少,这将限制薄膜的外延质量及光学特性的进一步提高.     

镓掺杂氧化锌透明导电薄膜的制备及其性能研究

采用射频磁控溅射方法在玻璃基片上制备了镓掺杂氧化锌(Ga∶ ZnO)透明导电薄膜,通过XRD、XPS、四探针仪和分光光度计等表征技术,研究了衬底温度对Ga∶ ZnO薄膜结构、组分、光学和电学性质的影响.结果表明:所有样品均为具有(002)择优取向的高质量透明导电薄膜,其晶体结构和光电性能与衬底温度密切相关.当衬底温度为673 K时,所制备的Ga∶ ZnO薄膜具有最大的晶粒尺寸(72.6 nm)、最低的电阻率(1.3×10-3Ω·cm)、较高的可见∶ZnO薄膜的光学能隙,结果显示随着衬底温度的升高,薄膜的光学能隙单调增加.     

超声喷雾热分解法制备ZnO薄膜及衬底温度对其性能的影响

以醋酸锌水溶液为前驱体溶液,采用超声喷雾热分解法在玻璃衬底上制备得到了温度在350℃到450℃范围内的ZnO薄膜.用X射线衍射(XRD)、扫描电镜(SEM)及紫外-可见分光光度计分析了ZnO薄膜的晶体结构、微观形貌及其光学性质,重点探究了衬底温度对ZnO薄膜生长过程及微观结构的影响.分析表明:制备的ZnO薄膜为六角铅锌矿结构,衬底温度对薄膜的质量有着重要的影响;所得薄膜在400℃时结晶性能好,沿c轴择优取向生长,具有优良的均匀性和致密性;所制备的薄膜在可见光区透过率高达86;以上,在紫外光区吸收强烈.     

基于直流磁控溅射室温制备ZnO薄膜研究

采用直流磁控溅射法在P型<100>晶向单晶硅衬底上室温制备ZnO薄膜,对室温制备的ZnO薄膜分别在500℃、600℃、700℃进行高温退火,通过采用X射线衍射(XRD)、拉曼光谱和场发射扫描电子显微镜(SEM)、HP4145B型半导体参数测试仪分析不同退火温度对室温生长ZnO薄膜微结构、表面形貌和,Ⅰ-Ⅴ特性影响.实验结果表明,室温生长的ZnO薄膜为非晶态,随退火温度增加,ZnO薄膜出现(002)、(100)、(101)晶面衍射峰且逐渐增强,晶粒大小相对增加,在700℃退火后,呈高度c轴择优取向,晶粒间界明显,拉曼光谱E2模增强.     

生长和退火温度对磁控溅射法制备的ZnO薄膜性能的影响

利用磁控溅射法于500 ℃、550 ℃、600 ℃和650 ℃下在Al2O3(001)衬底上生长ZnO薄.对生长的ZnO薄膜后分别进行了800 ℃退火和1000 ℃退火处理.利用X射线衍射(XRD)、霍尔测试仪和透射谱仪对薄膜的结构、电学和光学性质进行了研究,结果表明合适的生长温度和退火温度能够提高ZnO薄膜的结晶质量和性能.     

在钛酸锶衬底上外延生长ZnO薄膜及其性能研究

用脉冲激光淀积法(PLD)在(111)面SrTiO3衬底上外延生长ZnO单晶薄膜.样品分别在衬底温度为350℃、500℃、600℃下外延生长.X射线衍射(XRD)的结果表明,所得的ZnO单晶薄膜结晶性能好,只出现(002)和(004)两个衍射峰,(002)峰的半高宽度(FWHM)为0.23°.在荧光光谱中我们只观察到来源于带边激子跃迁的强UV发射,并且随着生长温度的升高,紫外峰的强度逐渐增强.样品的SEM图像表明所得ZnO薄膜表面平整,晶粒均匀.衬底温度为600℃时,所得到的ZnO薄膜结构完整,晶粒尺寸最大,均匀;而且紫外发射最强.     

CVD法制备高质量ZnO纳米线及生长机理

以金做催化剂,采用化学气相沉积(CVD)方法在Si(100)衬底上生长了整齐紧密排列的ZnO纳米线.XRD图谱上只有ZnO的(002)衍射峰,说明ZnO纳米线沿[001]择优生长;扫描电子显微镜分析表明:ZnO纳米线整齐排列在Si(100)衬底上,直径在100nm左右,平均长度为4μm.研究发现ZnO纳米线的生长机理与传统的V-L-S机理有所不同:生长过程中,在Si(100)衬底上先生长了大约500nm厚的ZnO薄膜,而ZnO纳米线生长在薄膜之上.     

MOCVD法在(220)CaF2衬底上生长ZnO薄膜及其性能研究

采用金属有机化学汽相沉积(MOCVD)法在(220)CaF2衬底上外延生长ZnO薄膜.利用X射线衍射(XRD)、紫外-可见光谱和光致发光谱(PL)对ZnO薄膜的结构和光学性能进行了分析.XRD结果表明,所制备的ZnO薄膜结晶性能良好,具有高度的(002)的择优取向,002衍射峰的半高宽(FMHM)为0.115°.所制备的ZnO薄膜透明,透过率超过85;.在常温的(He-Cd激光器)PL谱中,只有378.5 nm的带边发射.用同步辐射光源测试的真空紫外光谱中,在低温20K时,出现218 nm、368 nm、418 nm、554 nm发光峰,其中368 nm峰强度随着温度的升高强度逐渐下降,到常温时几乎消失.     

溶胶-凝胶法制备ZnO薄膜的特性研究

采用Sol-gel法,在普通载玻片上使用旋转涂覆技术生长了具有c轴择优取向生长的ZnO薄膜.用热分析、XRD、SEM等手段对薄膜样品进行了表征.热分析结果表明:二水醋酸锌-乙醇胺-乙二醇甲醚体系Sol-gel的热分解过程与纯二水合乙酸锌的分解过程大相径庭.ZnO薄膜的Sol-gel分解趋于在较窄的温度范围内一步完成.在Si(111)衬底和玻璃衬底上生长了ZnO薄膜,都表现出明显的c轴择优取向生长.对比了不同涂覆层数对ZnO薄膜结构及表面形貌的影响,ZnO薄膜的c轴择优取向生长特性随着涂覆层数的增加而减弱,这是由于ZnO薄膜的生长模式由层状生长向岛状生长转变所致.ZnO薄膜在可见光范围的透光率超过85;.     

Effects of growth temperature on the properties of ZnO/GaAs prepared by metalorganic chemical vapor deposition

A series of ZnO films were grown on GaAs(0 0 1) substrates at different growth temperatures in the range 250–720°C by metalorganic chemical vapor depostion. Field emission scanning electron microscopy was utilized to investigate the surface morphology of ZnO films. The crystallinity of ZnO films was investigated by the double-crystal X-ray diffractometry. The optical and electrical properties of ZnO films were also investigated using room-temperature photoluminescence and Hall measurements. Arrhenius plots of the growth rate versus reciprocal temperature revealed the kinetically limited growth behavior depending on the growth temperature. It was found that the surface morphology, structural, optical and electrical properties of the films were improved with increasing growth temperature to 650°C. All the properties of the film grown at 720°C were degraded due to the decomposition of ZnO film.     

Fabrication of hollow ZnO nanostructures by a CTAB‐assisted chemical bath deposition method

ZnO films consisted of hollow nanostructures were prepared by a CTAB‐assisted chemical bath deposition (CBD) method. ZnO rings, bowls and assemblies of hollow structures were successfully obtained on different substrates. Dense ZnO films consisted of sunken prisms can also be achieved by controlling the concentration of CTAB. The influences of reactant concentrations, types of the substrates and pre‐coated ZnO nanoparticles on the formation of ZnO films were examined. XRD patterns indicated the Wurtzite structure of ZnO and the preferred growth direction is [001]. The role of CTAB in CBD process was discussed and the evolution of different ZnO nanostructures was studied based on the observation of SEM. A plausible crystal growth mechanism was proposed for the formation of ZnO rings and bowls. The investigation of optical properties showed that high concentration of CTAB can improve the ultraviolet emission.     

(Ti/ZnO)N成分调制纳米多层膜的结构与透光导电性研究

采用射频(RF)和单极中频直流脉冲磁控溅射方法,在玻璃基板上制备了(Ti/ZnO)_N成分调制纳米多层膜,并研究了调制周期数对其结构及透光导电性能的影响。通过X射线衍射、拉曼光谱、原子力显微镜、紫外可见吸收光谱以及霍尔效应测试结果表明:(Ti/ZnO)_N成分调制纳米多层膜以(002)取向的纤锌矿型ZnO结构为主,具有明确的成分调制结构,各Ti层和各ZnO层厚度均匀连续,各界面平整且无明显扩散。在可见光范围的平均透光率大于85%,电阻率最小可达到2.63×10^-2 Ω·cm。     

HREM investigations of intermediate ZnO and ZnO/Y–ZrO2 layers in Y–ZrO2 bicrystals and ZnO films grown on Y–ZrO2 bicrystal substrates

The structure of yttrium-stabilized ZrO₂ (YSZ) bicrystals with ZnO and ZnO/YSZ/ZnO/YSZ/ZnO intermediate layers, as well as ZnO films grown on YSZ bicrystal (1 1 0)/90° substrates, has been investigated by means of high-resolution electron microscopy (HREM) and microanalysis. All bicrystals were produced by the solid-phase intergrowth (SPI) method. The internal ZnO film in the bicrystal formed at the SPI temperature of 1400°C consisted of domains with two symmetrical orientations: , and , . A bicrystal with a ZnO/YSZ/ZnO/YSZ/ZnO internal film was formed at the temperature of 1200°C. There was no mixing of ZnO and YSZ films and no traces of any solid-phase reactions were observed. Grains in all internal ZnO films and ZnO films grown on the bicrystal substrates had numerous stacking faults. It was found that SPI does not influence the density and structure of these defects. Orientational relationships between YSZ and ZnO in all samples were determined. The ZnO films grown on (1 1 0)/90° bicrystal substrates inherited the grain boundary (GB) from the substrate. Its structure and geometry is determined by four variants of ZnO grain growth.     

在Si(100)上以AlN作过渡层低温外延生长ZnO薄膜

采用脉冲激光沉积(PLD)方法在Si(100)上成功生长了高度c轴取向的AlN薄膜,并以此为衬底,实现了ZnO薄膜的低温准外延生长.通过X射线衍射(XRD)、原子力显微镜(AFM)以及荧光分光光度计表征ZnO薄膜的结构、表面形貌和发光性能.结果表明,ZnO薄膜能在AlN过渡层上沿c轴准外延生长,采用AlN过渡层后,其荧光强度也有大幅提高.     

Structural,optical and electrical properties of Ga-doped and (Ga,Co)-codoped ZnO films

The Ga-doped and (Ga, Co)-codoped ZnO films were grown on quartz glass substrate by inductively coupled plasma enhanced physical vapor deposition. The effect of Co doping and oxygen pressure on the structural, optical, electrical and magnetic properties of the as-grown films was investigated. The structural characterization revealed that high-quality films were grown with wurtzite structure and c-axis preferred crystalline orientation. The surface morphology was affected by Co doping and oxygen pressure. Room-temperature ferromagnetism was observed in (Ga, Co)-codoped ZnO films. We found that the optical and electrical properties were degraded with Co doping. The Ga-doped ZnO films had an average transmittance of above 88% in the visible wavelength, while (Ga, Co)-codoped ZnO showed a lower average transmittance (∼65%) due to the d-d transitions of Co²⁺. The resistivity and Hall mobility of (Ga, Co)-doped ZnO samples were lower than those of Ga-doped ZnO films when grown at the same oxygen pressure.     

MOCVD方法在Ti/Si(111)模板上生长ZnO薄膜的研究

本文采用常压MOCVD方法在Ti/Si（111）模板上生长了氧化锌（ZnO）薄膜，使用二乙基锌为Zn源，去离子水为O源。Si衬底上的Ti薄层采用电子束蒸发台蒸发，然后低温生长缓冲层并在高温下进行重结晶，接着在680％进行ZnO薄膜的生长。采用粉末衍射法、双晶X射线衍射及光致发光技术研究了材料的取向、结晶性能及发光性能。结果表明，本文制备了高度择优取向和良好发光性能的ZnO薄膜。     

B掺杂对平面结构MOCVD-ZnO薄膜性能的影响

本文研究了B2H6掺杂流量(B掺杂)对平面结构MOCVD-ZnO薄膜的微观结构和光电性能影响.XRD、SEM和AFM测试的研究结果表明,玻璃衬底上制备的ZnO薄膜具有(002)峰择优取向的平面结构,B掺杂使薄膜的球状晶粒尺寸变小,10 sccm流量时晶粒尺寸为～15 nm.ZnO:B薄膜的最小电阻率为5.7×10-3Ω·cm.生长的ZnO薄膜(厚度d=1150 nm)在400～900 nm范围的透过率为82;～97;,且随着B2H6掺杂流量增大,光学吸收边呈现蓝移(即光学带隙Eg展宽)现象.     

X-ray Diffraction Analysis of the Structure In0.53Ga0.47As Films Grown on (100) and (111)A GaAs Substrates with a Metamorphic Buffer

Crystallography Reports - Epitaxial In0.53Ga0.47As films, grown on GaAs substrates with the (100) and (111)А crystallographic orientations in the standard high-temperature and low-temperature...     

Suppression of phase separation in InGaN layers grown on lattice-matched ZnO substrates

Sapphire and SiC are typical substrates used for GaN growth. However, they are non-native substrates and result in highly defective materials. The use of ZnO substrates can result in perfect lattice-matched conditions for 22% indium InGaN layers, which have been found to suppress phase separation compared to the same growths on sapphire. InGaN layers were grown on standard (0 0 0 2) GaN template/sapphire and (0 0 0 1) ZnO substrates by metalorganic chemical vapor deposition. These two substrates exhibited two distinct states of strain relaxation, which have direct effects on phase separation. InGaN with 32% indium exhibited phase separation when grown on sapphire. Sapphire samples were compared with corresponding growths on ZnO, which showed no evidence of phase separation with indium content as high as 43%. Additional studies in Si-doping of InGaN films also strongly induced phase separation in the films on sapphire compared with those on ZnO. High-resolution transmission electron microscopy results showed perfectly matched crystals at the GaN buffer/ZnO interface. This implied that InGaN with high indium content may stay completely strained on a thin GaN buffer. This method of lattice matching InGaN on ZnO offers a new approach to grow efficient emitters.