The formation of multiple adiabatic shear bands

In a previous paper, Zhou et al. [2006. A numerical methodology for investigating adiabatic shear band formation. J. Mech. Phys. Solids, 54, 904-926] developed a numerical method for analyzing one-dimensional deformation of thermoviscoplastic materials. The method uses a second order algorithm for integration along characteristic lines, and computes the plastic flow after complete localization with high resolution and efficiency. We apply this numerical scheme to analyze localization in a thermoviscoplastic material where multiple shear bands are allowed to form at random locations in a large specimen. As a shear band develops, it unloads neighboring regions and interacts with other bands. Beginning with a random distribution of imperfections, which might be imagined as arising qualitatively from the microstructure, we obtain the average spacing of shear bands through calculations and compare our results with previously existing theoretical estimates. It is found that the spacing between nucleating shear bands follows the perturbation theory due to Wright and Ockendon [1996. A scaling law for the effect of inertia on the formation of adiabatic shear bands. Int. J. Plasticity 12, 927-934], whereas the spacing between mature shear bands is closer to that predicted by the momentum diffusion theory of Grady and Kipp [1987. The growth of unstable thermoplastic shear with application to steady-wave shock compression in solids. J. Mech. Phys. Solids 35, 95-119]. Scaling laws for the dependence of band spacing on material parameters differ in many respects from either theory.     

A numerical methodology for investigating the formation of adiabatic shear bands

In this paper, we present a numerical approach for analyzing thermo-visco-plastic deformation in one dimension. The method, which is accurate to second order, is based on integration along the characteristic lines. It is able to simulate fully localized plastic flow with high resolution and good efficiency. We apply this numerical scheme to the analysis of shear localization, emphasizing the interactions between a single shear band and its surroundings and among the members of a periodic array of shear bands. It is found that a shear band may grow intermittently due to interactions with other bands. The developed method is specifically adequate for analyzing the self-organized multiple adiabatic formation process, which will be discussed in the follow-up paper.     

双周期刚性线纵向剪切问题的应力奇异因子

研究了双周期刚性线的纵向剪切问题，利用椭圆函数的保角变换、Riemann-Schwarz对称原理和奇点分析等技术，得以了全场应力及应力奇异因子的精确解，分析了刚性线夹杂横向和纵向间距对应力奇异因子的影响。     

膨胀土的现场抗剪试验研究

由于膨胀土的裂隙性和超固结特性,膨胀土的抗剪强度不仅是膨胀土地区边坡设计的重要依据,而且一直是膨胀土边坡研究领域的重要课题。本文以南阳膨胀土为例,对膨胀土现场抗剪试验的试样制备及试验方法进行探讨,通过对该地区典型滑坡反算证明,文中的现场抗剪试验方法及抗剪强度的计算公式是合理的。     

颗粒材料剪切流动状态转变的环剪试验研究

颗粒材料的剪切流动行为广泛地存在于滑坡、泥石流等自然灾害以及矿物原料传输、泵送等工业过程中.颗粒材料在不同体积分数、剪切速率和应力约束下会表现出不同的流动状态并发生相互转化.对颗粒材料在剪切流动过程中力学特性的研究有助于加深理解其发生不同流动状态的内在机理,为解决相应的颗粒材料问题提供理论依据.为此,本文研制了颗粒材料剪切流动的中型环剪仪,并对颗粒材料在不同法向约束应力和剪切速率下的剪切应力和体积膨胀率进行了测试.结果表明,剪切应力和体积膨胀率均随剪切速率的增大而增大,但增长速率在临界剪切速率处发生转变,使其随剪切速率的平方呈分段式线性增长.通过对颗粒材料在不同剪切速率和惯性数下有效摩擦系数变化趋势的分析,讨论了颗粒材料由慢速流向快速流转化的基本规律,以及在临界剪切速率处发生流动状态转化的内在条件.此外,通过对不同法向应力下临界剪切速率以及快速流动下运动规律的测试,发现临界剪切速率随法向应力的增加而减小,即法向应力可促进颗粒材料由慢速流向快速流的转化,但在快速流动状态下的有效摩擦系数对法向应力不敏感.以上对颗粒材料在不同剪切速率、法向应力下流动状态的环剪试验研究有助于揭示其发生不同流动状态转化的内在机理.      

刚性圆管中血液周期振荡流的切应力分布

本文通过求解圆管内血液振荡流的基本方程，求得圆管内血液流的压力梯度与切应力之间的关系式。在此基础上，详细讲座了圆管中轴向流速和切变率谐波的变化规律，指出流速谐波和切变率谐波的幅值都将随着谐波次数的增大而逐渐减小。为了使所得结果便于应用。文章通过管轴向中心线流速与压力梯度之间的关系式，进一步给出一种利用管轴向中心线流速计算管内切应力分布的简便方法。该方法用于检测活体血管内血液振荡流的切应力分布，具有操作简单，精度较高的优点。最后，以人体颈动脉为例，讨论血液周期振荡流的切应力的分布特性。发现在任意时刻，除了邻近管壁处切应力急剧增大到一定数值之外，沿管截面切应力分布相当均匀且接近于零，呈现出与定常流不同的切应力分布特征。     

有腹筋混凝土梁的剪切刚度分析模型

钢筋混凝土梁的挠度计算通常不计入剪切变形的贡献,然而对于斜向开裂的有腹筋混凝土梁,斜裂缝会显著降低梁体的有效剪切刚度,导致剪切变形值显著增大,因此在验算评估时应予以考虑.为评价钢筋混凝土梁斜向开裂后的有效剪切刚度,首先,基于变角桁架模型推导了钢筋混凝土梁在箍筋屈服状态下的有效剪切刚度;与弹性剪切刚度比较发现,剪切刚度退化系数的主要影响因素为材料弹模比、配箍率和斜压杆倾角.其次,基于试验剪切变形曲线表现出的刚度退化规律,提出了可用于不同开裂程度下剪切刚度计算的恒定切线刚度退化模式,并采用开裂后的剪力增量作为反映开裂程度的定量指标.最后,根据最小能量原理得到了剪切刚度退化中两个关键参数:斜压杆倾角和剪切刚度退化系数的解析公式.通过2根薄腹混凝土梁剪切变形试验以及收集的15个受剪梁段的剪切变形数据对模型有效性进行了验证,验证结果表明:有腹筋混凝土梁剪切刚度分析模型能较为准确地预测箍筋屈服状态的剪切刚度,并能反映不同开裂程度下的剪切刚度退化规律.     

由Bezier曲线构造的聚合物熔体剪切黏度模型

为提高聚合物熔体剪切黏度模型的描述精度,提出了一个基于二次Bezier 曲线的黏度模型. 模型采用分段函数描述,在对数坐标系中,低剪切速率时的牛顿区和高剪切速率时的幂律区采用线性函数,介于二者之间的过渡区采用二次Bezier 曲线. 通过牛顿区和幂律区的直线延长线构造Bezier 曲线的控制多边形,从而保证三段曲线的光滑过渡. 模型可以明确给出任意温度下低剪切速率时牛顿区的结束点,以及高剪切速率时幂律区的开始点. 拟合算例表明,所提出模型的拟合精度明显高于Cross-Arrhenius 黏度模型.      

Sensitivity of the shear gage to normal strains

This paper documents an experimental study that was conducted to demonstrate the sensitivity of the shear gage to the presence of normal strains. The shear gage is a specially designed strain gage rosette that measures the average shear strain in the test section of notched specimens such as the losipescu, Arcan and compact shear specimens. These specimens can have complicated stress states with high shear and normal strain gradients. To evaluate the sensitivity of the shear gage to normal strains, shear gages were tested on an Arcan specimen. The Arcan specimen is a notched specimen that can be loaded in pure shear (90 deg), pure tension (0 deg) and at intermediate 15- deg increments. The shear modulus for an aluminum specimen was determined at each of these loading angles. It was found that the gages display nearly zero sensitivity to normal strains ( _x, _y). Moiré interferometry was used to document the shear and normal strain distributions in the test section and to provide an independent method for determining the average shear strain. These results reinforce the robust nature of testing with the shear gage.     

基于剪切梁的地垒断层型矿震解析分析

为得到地垒组合型断层失稳诱发矿震的方式及断层影响区顶板平衡结构的解析解,将顶板简化为剪切梁模型进行分析.基于弹性剪切梁确定了顶板最大等效剪力位置和顶板初次垮落步距的计算公式.顶板等效剪力随着采空区跨度的增加而增加,达到顶板极限值时发生初次来压,顶板断裂位置出现在煤层内部.用弹塑性剪切梁模型分析存在地垒断层的采场顶板初次来压和周期来压,当最大等效剪力达到断层剪切极限时,断层错动,释放能量,发生矿震.     

高速切削过程中诱发绝热剪切带形成的热塑性剪切波

提出了高速切削过程中诱发绝热剪切带形成的热塑性剪切波的传播机理,针对锯齿形切屑中热望性区域内的塑性梯度变形特征、动量和能量耗散情况,建立了与切削条件相关的热塑性剪切波的传播模型及剪切带宽度模型.在此基础上,通过淬硬45钢的切削实验并结合改进的Johnson-Cook本构模型分析了热塑性剪切波的传播规律,并将剪切带宽度模型与已提出的DB模型、WR模型和DM模型做了对比,结果表明,由热塑性剪切波传播理论推导的剪切带宽度模型与实验结果较其他模型吻合较好.     

An analysis of the shear failure of rigid-linear hardening beams under impulsive loading

A theoretical rigid-plastic analysis for the dynamic shear failure of beams under impulsive loading is presented when using a travelling plastic shear hinge model which takes into account material strain hardening. The maximum dynamic shear strain and shear strain-rate can be predicted in addition to the permanent transverse deflections and other parameters. The conditions for the three modes of shear failure, i.e., excess deflection failure, excess shear strain failure and adiabatic shear failure are analyzed. The special case of an infinitesimally small plastic zone is discussed and compared with Nonaka's solution for a rigid, perfectly plastic material. The results can also be generalized to examine the dynamic response of fibre-reinforced beams.     

基于剪切变形的矩形梁剪力滞求解方法

Timoshenko梁通过假设截面的剪切刚度和附加平均剪切转角变形的方式来近似修正初等梁中未考虑剪切变形能的问题,这与梁剪应力沿梁高变化的实际不符。本文基于材料力学剪应力计算式和相应的剪切变形理论,从剪切变形与梁的位移关系入手,导出矩形梁考虑剪切变形时的纵向位移沿梁高方向的函数关系式,证明该位移可分解为纯弯曲引起的位移和剪力引起的剪力滞翘曲位移之和。应用剪力滞广义坐标与广义力的概念,基于能量变分原理得到等截面梁剪力滞控制微分方程组及其通解形式。对均布荷载作用下矩形简支梁的算例分析表明,本文算法与弹性力学精确解对比,两者的应力和挠度剪力滞系数求解结果非常接近,本文算法有足够的精度,且比弹性力学简单。     

用双剪屈服准则对钢筋混凝土板进行塑性铰线的极限分析

利用双剪屈服准则建立了用机动法计算钢筋混凝土薄板极限载荷的新的塑性铰线理论，并导出了双向布置钢筋的钢筋混凝土板的屈服条件，实例计算表明其更符合实验结果。     

压缩剪切测试中载荷传递行为的数字光弹性研究

结合光弹性四步彩色相移法,提出改进的六步相移法来计算全场剪应力,对径压缩圆盘实验证实了该方法的正确性,并进一步研究了同质材料连接结构在压缩剪切测试中的层间剪切行为。实验结果表明:全场等色线条纹级数和剪应力连续分布且随载荷而增加;中线附近剪应力趋于零,而条纹级数为峰谷。在连接界面上的条纹级数和剪应力出现峰值,特别是在连接界面端部为最高,在最大载荷下可分别达3.5级和2.4MPa,是导致连接界面脱粘开裂的危险区域。连接结构通过层间剪应力进行应力传递,在连接界面上剪应力与外载基本保持平衡。     

饱和土中剪切带宽度的研究

主要对饱和土在简单剪切和耦合载荷下的剪切带宽进行了理论分析. 在模型中考虑了剪胀、孔压耗散、惯性及孔隙水和土颗粒之间阻力等因素的耦合效应，将有效应力考虑为应变、应变率和孔隙压力的函数. 通过对模型的简化分析得到简单剪切和耦合应力状态下的剪切带宽度的近似计算公式. 分析表明，当土体失稳后，会出现有限厚度的剪切带, 且其形成是一个后期过程，可以忽略惯性效应. 剪切带的厚度依赖于孔隙压力特性和土体骨架的剪胀特性，但是不依赖应力状态. 最后将分析与实验结果进行了对比，在一定程度上，两者是符合的.     

剪应力对培养内皮细胞表面ATP浓度的调节

剪应力信号转导是目前细胞生物力学的研究热点之一。Ca^2＋作为一种第二信使在剪应力信号转导中扮演了重要角色，钙信号转导是通过胞内自由Ca^2＋浓度变化来实现的。胞内Ca^2＋浓度的大小不仅依赖于细胞承受剪应力的大小，同时依赖于细胞外ATP的浓度。本文采用剪应力诱发内皮细胞分泌ATP的时变模型，通过对平行平板流动腔中的ATP浓度场进行数值模拟，分析了剪应力对培养内皮细胞表面ATP浓度的影响。结果表明，剪应力诱发的ATP分泌明显影响细胞表面附近ATP的浓度；剪应力、对流和扩散效应、ATP的水解作用共同决定了细胞外表面附近ATP的浓度。这一结果提示，剪应力大小并非剪应力信号转导过程中的唯一决定因素；剪应力的作用、激动剂的浓度改变共同参与了剪应力信号转导。     

QUANTIFICATION OF SHEAR DAMAGE EVOLUTION IN ALUMINIUM ALLOY 2024T3

Shear damage may occur in the process of metal machining such as blanking and cutting, where localized shear deformation is developed. Experimental findings indicate that microscopic shear damage evolution in aluminium alloy 2024T3 (A1 2024T3) is a multi-stage mechanism, including particle cracking, micro-shear banding, matrix microcracking and coalescence of microcracks. This study is an attempt to use a set of equations to describe the multi-stage shear damage evolution in Al 2024T3. The shear damage variables in terms of multi-couple parameters of a power-law hardening material have been defined. An evolution curve of shearing damage has been calculated from experimental data. The values of the shear damage variable at different stages of damage have also been calculated. By making use of the findings, the relation between the microscopic shear damage evolution and the macroscopic shear response of the material has been discussed.     

An experimental and numerical investigation of different shear test configurations for sheet metal characterization

Simple shear tests are widely used for material characterization especially for sheet metals to achieve large deformations without plastic instability. This work describes three different shear tests for sheet metals in order to enhance the knowledge of the material behavior under shear conditions. The test setups are different in terms of the specimen geometry and the fixtures. A shear test setup as proposed by Miyauchi, according to the ASTM standard sample, as well as an in-plane torsion test are compared in this study. A detailed analysis of the experimental strain distribution measured by digital image correlation is discussed for each test. Finite element simulations are carried out to evaluate the effect of specimen geometries on the stress distributions in the shear zones. The experimental macroscopic flow stress vs. strain behavior shows no significant influence of the specimen geometry when similar strain measurements and evaluation schemes are used. Minor differences in terms of the stress distribution in the shear zone can be detected in the numerical results. This work attempts to give a unique overview and a detailed study of the most commonly used shear tests for sheet metal characterization. It also provides information on the applicability of each test for the observation of the material behavior under shear stress with a view to material modeling for finite element simulations.     

绝热剪切损伤和破坏的数值模拟研究

绝热剪切破坏是冲击载荷作用下金属材料中经常出现的一种重要破坏模式,尽管已经在实验中观察到了绝热剪切带内部的损伤现象,但是在理论和计算模型中往往还只是考虑它的热软化效应,对与之伴随的损伤破坏效应却鲜有讨论．该文在前人实验的基础上,提出了一个适用于绝热剪切带内部微孔洞损伤发展的演化方程,并在本构方程中同时考虑了温度和损伤对材料的影响,成功地模拟出了绝热剪切带的热软化效应和损伤破坏效应．