不同加载状态下TA2钛合金绝热剪切破坏响应特性

一般认为绝热剪切现象在宏观上表现为材料动态本构失稳,即热软化大于应变硬化.本文采用帽型受迫剪切试样研究TA2钛合金的动态力学特性和本构失稳过程.首先对剪切区加载应力状态进行理论和数值分析,通过合理设计帽型试样,剪切区变形可近似按剪切状态处理;结合二维数字图像相关法(two-dimensional digital image correlation,DIC-2D)直接测试试样剪切区应变演化,给出帽型受迫剪切实验的等效应力-应变响应曲线.进一步,利用Hopkinson压杆对TA2钛合金开展动态压缩及帽型剪切对比试验研究,比较压缩、剪切试验得到的等效应力-应变曲线,采用"冻结"试样方法分析试样中绝热剪切局域化演化过程,探讨不同加载状态下TA2钛合金的绝热剪切破坏现象及其动态力学响应特性.实验结果表明,在塑性变形初始阶段,动态压缩及剪切加载下的等效应力-应变曲线符合较好,但随塑性损伤发展及绝热剪切带形成,两者出现分离,表明损伤及绝热剪切演化过程与应力状态相关.剪切试样实验得到的本构"软化"特性能够反映绝热剪切带起始、破坏演化过程的力学响应特性,而在动态压缩实验中,即使试样中已出现双锥形的绝热剪切带及局部裂纹分布,其表观等效应力-应变曲线并不出现软化特征,动态压缩实验无法得到关于绝热剪切起始、发展以及破坏的本构软化响应特性.     

Experiments and modeling of ballistic penetration using an energy failure criterion

One of the most intricate problems in terminal ballistics is the physics underlying penetration and perforation. Several penetration modes are well identified, such as petalling, plugging, spall failure and fragmentation (Sedgwick, 1968). In most cases, the final target failure will combine those modes. Some of the failure modes can be due to brittle material behavior, but penetration of ductile targets by blunt projectiles, involving plugging in particular, is caused by excessive localized plasticity, with emphasis on adiabatic shear banding (ASB).Among the theories regarding the onset of ASB, new evidence was recently brought by Rittel et al. (2006), according to whom shear bands initiate as a result of dynamic recrystallization (DRX), a local softening mechanism driven by the stored energy of cold work. As such, ASB formation results from microstructural transformations, rather than from thermal softening. In our previous work (Dolinski et al., 2010), a failure criterion based on plastic strain energy density was presented and applied to model four different classical examples of dynamic failure involving ASB formation. According to this criterion, a material point starts to fail when the total plastic strain energy density reaches a critical value. Thereafter, the strength of the element decreases gradually to zero to mimic the actual material mechanical behavior.The goal of this paper is to present a new combined experimental–numerical study of ballistic penetration and perforation, using the above-mentioned failure criterion. Careful experiments are carried out using a single combination of AISI 4340 FSP projectiles and 25[mm] thick RHA steel plates, while the impact velocity, and hence the imparted damage, are systematically varied. We show that our failure model, which includes only one adjustable parameter in this present work, can faithfully reproduce each of the experiments without any further adjustment.Moreover, it is shown that the most common failure criterion based on a critical strain is simply inadequate to reproduce the results, due to the linear nature of the damage evolution. The advantages of the energy-based failure criterion are discussed in detail.     

爆炸荷载作用下钢筋混凝土梁的动力响应及破坏形态分析

对基于Timoshenko梁理论建立的非线性动力有限元法作了改进。根据压区理论得到混凝土的平均剪应力和平均剪应变关系,建立了能反映箍筋的抗剪作用的材料模型;此外,对结构在爆炸荷载作用下可能出现的各种响应现象进行了描述,以准确地预测梁破坏时不同位置截面上钢筋和混凝土的受力、变形及破坏情况。应用改进的材料模型,对爆炸荷载作用下的五个钢筋混凝土试验梁的动力响应和破坏形态进行了数值模拟,结果表明,该数值方法能较好地模拟钢筋混凝土梁的弯曲、弯剪和剪切等破坏形态。     

On dimensionless numbers for dynamic plastic response of structural members

Summary A dimensional analysis is reported for the dynamic plastic response and failure of structural members, which includes material strain hardening, strain rate and temperature effects. Critical shear failure conditions are also discussed based on the dimensional analysis results. It is shown that the response number R _n proposed in [3], is an important independent dimensionless number for the dynamic plastic bending and membrane response of structural members. However, additional dimensionless numbers are necessary when transverse shear, strain hardening, strain rate, and temperature effects are important. Received 22 February 1999; accepted for publication 15 June 1999     

钨纤维增强金属玻璃复合材料弹穿甲钢靶的实验研究

为具体研究钨纤维增强金属玻璃复合材料的力学特性及其穿甲自锐特征,开展了相应的准静态和 动态力学实验,并用火炮开展了复合材料弹体撞击钢靶的穿甲实验,同时利用金相分析对材料失效模式进行 了较系统的识别和分类,并同静动态实验数据进行比较分析,最后开展了材料自锐剪切失效的机理讨论。实 验获得了复合材料的静动态力学特性及其自锐穿甲的形貌,相关分析显示,材料的变形具有明显的应变率效 应,在复合材料弹体侵彻/穿甲过程中,弹体的破坏方式主要表现为局域化的剪切变形和断裂,并呈现出4种 自锐剪切失效模式,增强钨纤维也表现出3类失效破坏模式。     

圆柱形爆炸容器绝热剪切瞬态失效过程

开展了圆柱形爆炸容器逐级加载和破坏实验,根据容器最终的断裂面和微观形貌观测,提出了爆炸容器绝热剪切失效模式.建立了应变率-应变空间内的绝热剪切损伤演化模型,将绝热剪切不同演化阶段的临界状态与宏观的力学条件联系起来,并将这些力学临界条件作为动态失效准则引入到宏观计算程序中,模拟爆炸容器发生绝热剪切的的瞬态过程,模拟结果成...     

An experimental and numerical investigation of different shear test configurations for sheet metal characterization

Simple shear tests are widely used for material characterization especially for sheet metals to achieve large deformations without plastic instability. This work describes three different shear tests for sheet metals in order to enhance the knowledge of the material behavior under shear conditions. The test setups are different in terms of the specimen geometry and the fixtures. A shear test setup as proposed by Miyauchi, according to the ASTM standard sample, as well as an in-plane torsion test are compared in this study. A detailed analysis of the experimental strain distribution measured by digital image correlation is discussed for each test. Finite element simulations are carried out to evaluate the effect of specimen geometries on the stress distributions in the shear zones. The experimental macroscopic flow stress vs. strain behavior shows no significant influence of the specimen geometry when similar strain measurements and evaluation schemes are used. Minor differences in terms of the stress distribution in the shear zone can be detected in the numerical results. This work attempts to give a unique overview and a detailed study of the most commonly used shear tests for sheet metal characterization. It also provides information on the applicability of each test for the observation of the material behavior under shear stress with a view to material modeling for finite element simulations.     

激光金属沉积GH4169在不同应变率下的剪切特性及破坏机理研究

为了能在传统的分离式Hopkinson压杆上准确可靠地测试激光金属沉积GH4169的动态剪切特性，基于数值模拟方法对比分析了三种不同动态剪切试样形式及尺寸对剪切区应力分布的影响，结果表明:经过尺寸优化后的双剪切试样的剪切区剪应力占主导地位，可实现近似纯剪切的动态剪切实验。利用此试样形式，系统测试了不同取向（扫描方向、沉积方向）的LMD GH4169试样在不同应变率下的剪切应力应变曲线，并对破坏后试样进行了SEM分析观察。结果表明:(1) 本文中选用的试样形式剪切纯度高，应力沿剪切区宽度厚度分布均匀，可以更好地得到材料的动态剪切特性；(2) 对实验所得剪应力-剪应变曲线进行分析，发现本材料在扫描路径方向和沉积方向并没有表现出明显的各向异性，但随着应变率的增加，具有明显的应变率强化效应；将单轴压缩和动态剪切应力应变曲线同时转换为等效应力应变曲线，对比证实了试样形式能很好反应材料的剪切特性；(3) 通过对LMD GH4169剪切变形破坏试样的微观分析发现，随着应变率升高，断口韧窝尺寸和深度减小，韧性降低，在更小的变形量下容易剪切失效。初始微观缺陷容易导致材料的动态剪切破坏。     

考虑剪切效应的旋转FGM楔形梁刚柔耦合动力学建模与仿真

本文对一类中心刚体-柔性梁系统在大范围转动下的刚柔耦合动力学问题进行了研究. 柔性梁为功能梯度材料(functionally graded materials, FGM)楔形变截面梁,材料体积分数在梁轴向呈幂律分布变化. 以弧长坐标来描述柔性FGM梁的几何位移关系,分别使用倾角和拉伸应变变量描述柔性梁的横向弯曲和纵向拉伸变形,并计及剪切效应. 采用假设模态法离散变形场,运用第二类拉格朗日方程进行方程推导,得到系统考虑剪切效应的刚柔耦合动力学模型. 基于全新的刚柔耦合动力学建模理论,研究不同轴向材料梯度分布的FGM楔形梁,通过数值仿真计算,分析讨论不同的转速、梯度分布规律以及变截面参数对系统动力学特性的影响. 结果表明,剪切效应对大高跨比的FGM楔形梁的变形影响较为明显,不容忽略;材料梯度分布规律和截面参数的选取均会对旋转FGM楔形梁的动力学响应和频率产生较大影响. 本文提出的考虑剪切效应的倾角刚柔耦合动力学模型是对以往非剪切模型的进一步完善,可应用于工程中的 Timoshenko梁结构的动力学问题求解.      

部分剪力连接钢—砼组合梁的滑移及曲率分析

对受均布荷载作用的简支部分剪力连接钢－砼组合梁的滑移应变和滑移的分布规律进行了理论分析,得出部分剪力连接钢－砼组合梁的剪力连接程度系数与滑移应变和滑移的关系。分析了考虑滑移效应的梁的曲率及其与剪力连接程度系数之间的关系。结果与结构在弹性阶段的实验相当吻合,对组合梁挠度的精确计算有指导意义。     

Modeling adiabatic shear failure from energy considerations

The numerical simulation of dynamic structural failure by localized shear is quite complex in terms of constitutive models and choice of adequate failure criteria, along with a pronounced mesh-sensitivity. As a result, the existing numerical procedures are usually quite sophisticated, so that their application for design purposes is still limited. This study is based on the implementation of a simple energy-based criterion, which was developed on experimental considerations (Rittel et al., 2006), and uses a minimal number of adjustable parameters. According to this criterion, a material point starts to fail when the total strain energy density reaches a critical value. Thereafter, the strength of the element decreases gradually to zero to mimic the actual structural behavior. The criterion was embedded into commercial finite element software and tested by simulating numerically four typical high-rate experiments. The first is the dynamic torsion test of a tubular specimen. The second concerns the failure mode transition in mode II fracture of an edge crack in plain strain. The last two involve dynamic shear localization under high rate compression of a cylindrical and a shear compression specimen. A very good adequation was found both qualitatively and quantitatively. Qualitatively, in terms of failure path selection, and quantitatively, in terms of local strains, temperatures and critical impact velocity. The proposed approach is enticing from an engineering perspective aimed at predicting the onset and propagation of dynamic shear localization in actual structures.     

有腹筋混凝土梁的剪切刚度分析模型

钢筋混凝土梁的挠度计算通常不计入剪切变形的贡献,然而对于斜向开裂的有腹筋混凝土梁,斜裂缝会显著降低梁体的有效剪切刚度,导致剪切变形值显著增大,因此在验算评估时应予以考虑.为评价钢筋混凝土梁斜向开裂后的有效剪切刚度,首先,基于变角桁架模型推导了钢筋混凝土梁在箍筋屈服状态下的有效剪切刚度;与弹性剪切刚度比较发现,剪切刚度退化系数的主要影响因素为材料弹模比、配箍率和斜压杆倾角.其次,基于试验剪切变形曲线表现出的刚度退化规律,提出了可用于不同开裂程度下剪切刚度计算的恒定切线刚度退化模式,并采用开裂后的剪力增量作为反映开裂程度的定量指标.最后,根据最小能量原理得到了剪切刚度退化中两个关键参数:斜压杆倾角和剪切刚度退化系数的解析公式.通过2根薄腹混凝土梁剪切变形试验以及收集的15个受剪梁段的剪切变形数据对模型有效性进行了验证,验证结果表明:有腹筋混凝土梁剪切刚度分析模型能较为准确地预测箍筋屈服状态的剪切刚度,并能反映不同开裂程度下的剪切刚度退化规律.     

A constitutive model for orthotropic elasto-plasticity at large strains

Summary The paper presents a thermodynamically consistent constitutive model for elasto-plastic analysis of orthotropic materials at large strain. The elastic and plastic anisotropies are assumed to be persistent in the material but the anisotropy axes can undergo a rigid rotation due to large plastic deformations. The orthotropic yield function is formulated in terms of the generally nonsymmetric Mandel stress tensor such that its skew-symmetric part is additionally taken into account. Special attention is focused on the convexity of the yield surface resulting in the nine-dimensional stress space. Of particular interest are new convexity conditions which do not appear in the classical theory of anisotropic plasticity. They impose additional constraints on the material constants governing the plastic spin. The role of the plastic spin is further studied in simple shear accompanied by large elastic and large plastic deformations. If the plastic spin is neglected, the shear stress response is characterized by oscillations with an amplitude strictly dependent on the degree of the plastic anisotropy.accepted for publication 2 March 2004     

水工结构高强钢筋混凝土梁受剪性能试验研究

通过对12根配置高强箍筋的混凝土梁在集中荷载作用下的受剪试验,研究梁的挠度、箍筋应变、斜裂缝扩展规律及破坏形态。依据现行《水工混凝土结构设计规范》,对比分析试验梁斜截面承载力及考虑荷载长期作用的正常使用阶段斜裂缝宽度。研究结果表明,配置高强箍筋的混凝土梁斜向开裂规律和受力特征与普通钢筋混凝土梁基本相同,受剪承载力可按现行《水工混凝土结构设计规范》公式计算,且有较高安全储备。当考虑荷载长期作用,HRBF500钢筋在水工结构中抗拉强度设计值取360MPa时,斜裂缝宽度满足正常使用极限状态要求。     

Granular plasticity,a contribution from discrete mechanics

Failures by divergence instabilities in rate-independent non-associated material, such as granular matter, can occur from mechanical states described by the plastic stress limit surface, but also from stress states strictly included within this surface. Besides, the failure mode may be localized, with for instance the formation of shear bands, or diffuse with a strain field remaining homogeneous. All these failures can be described in a unique framework where plastic limit stress states appear as particular cases of generalized limit states; and where the effective development of failure is characterized by the unbounded increase of response parameters linked by a failure rule (i.e. a generalized plastic flow rule), together with a bifurcation of the mechanical response from a quasi-static pre-failure response to a dynamic post-failure one. All these features are discussed and highlighted from direct numerical simulations performed with a discrete element model. Moreover, the second order work criterion directly related at the macroscopic scale to divergence instabilities, is shown to be also relevant at the scale of inter-particle contacts.     

一种用于材料高应变率剪切性能测试的新型加载技术

高应变率下的冲击剪切实验技术是材料动态力学行为及其微观机理研究的重要基础.采用分离式霍普金森压杆(split Hopkinson pressure bar)装置一般可以获得材料在104s-1以内应变率的动态力学性能.在超过104s-1的应变率下对材料进行冲击剪切测试时,通常需要采用高速压剪飞片技术或由气炮发射子弹对试样进行直接加载.本文提出一种可用于传统霍普金森压杆技术的新型双剪切试样,可以在103~105s-1剪应变率范围实现对材料剪切性能的精确测量;同时,可以对材料的变形及失效过程进行直接观测.试样与压杆之间避免了复杂的界面或连接装置,通过转接头可以保证试样与压杆直接接触,提高测试精度,同时可以防止因试样的横向位移而导致的非均匀变形.获得了紫铜在1400~75000s-1应变率下的剪应力-剪应变曲线,并采用计算软件"ABAQUS/Explicit"对双剪切试样的动态加载过程进行了数值模拟和结果验证.分析表明,剪切区的主要区域内剪切成分占主导地位,其应力应变场沿厚度及宽度方向基本呈均匀分布.实验得到的剪应力-剪应变曲线与模拟结果吻合较好,说明所提出的基于分离式霍普金森压杆系统的双剪切试样可以为材料的高应变率力学性能测试提供一种方便有效的加载技术.      

A combined necking and shear localization analysis for aluminum sheets under biaxial stretching conditions

A combined necking and shear localization analysis is adopted to model the failures of two aluminum sheets, AA5754 and AA6111, under biaxial stretching conditions. The approach is based on the assumption that the reduction of thickness or the necking mode is modeled by a plane stress formulation and the final failure mode of shear localization is modeled by a generalized plane strain formulation. The sheet material is modeled by an elastic-viscoplastic constitutive relation that accounts for the potential surface curvature, material plastic anisotropy, material rate sensitivity, and the softening due to the nucleation, growth, and coalescence of microvoids. Specifically, the necking/shear failure of the aluminum sheets is modeled under uniaxial tension, plane strain tension and equal biaxial tension. The results based on the mechanics model presented in this paper are in agreement with those based on the forming limit diagrams (FLDs) and tensile tests. When the necking mode is suppressed, the failure strains are also determined under plane strain conditions. These failure strains can be used as guidances for estimation of the surface failure strains on the stretching sides of the aluminum sheets under plane strain bending conditions. The estimated surface failure strains are higher than the failure strains of the forming limit diagrams under plane strain stretching conditions. The results are consistent with experimental observations where the surface failure strains of the aluminum sheets increase significantly on the stretching sides of the sheets under bending conditions. The results also indicate that when a considerable amount of necking is observed for a sheet metal under stretching conditions, the surface failure strains on the stretching sides of the sheet metal under bending conditions can be significantly higher.     

Ti-6Al-4V在高应变率下的动态剪切特性及失效机理

采用基于霍普金森压杆的新型加载技术对Ti-6Al-4V材料的动态剪切特性及失效机理进行了测试研究。获得了Ti-6Al-4V材料在超过104 s-1应变率下的剪应力-剪应变曲线及失效参数。研究发现,材料的流动应力存在明显的应变率强化效应;随着应变率的增加,材料的失效应力逐渐增大,而失效应变逐渐减小。采用ABAQUS/Explicit对加载过程进行了数值模拟。结果显示,剪切区材料基本处于平面剪切状态,应力应变场分布较为均匀,计算得到的剪应力-剪应变曲线与实验结果吻合较好。经断口分析可知,随着应变率的升高,Ti-6Al-4V的失效机理存在由韧窝、拉伸韧窝至台阶及河流花样的演化过程,材料的失效模式主要表现为韧性断裂。     

A NOVEL APPROACH TO TESTING THE DYNAMIC SHEAR RESPONSE OF Ti-6Al-4V

Modifications were made on the traditional split Hopkinson pressure bar (SHPB) system to conduct dynamic shear tests. The shear response of Ti-6Al-4V was acquired at a shear strain rate of 10 4 s 1 by using this modified apparatus. The geometry as well as the clamping mode of the double-notch specimen was optimized by commercial FEM software ABAQUS, and the feasibility of the experiment set-up was validated. A shear stress calibration coefficient of τ = 1.03 and a shear strain calibration coefficient of Γ = 0.50 were obtained.We have employed high-speed photography to record the deformation process, especially the initiation and propagation of adiabatic shear band (ASB), during the dynamic shear test. The frames show that the time duration from ASB initiation to its completion is less than 2 μs, from which we can estimate that the propagation speed of ASB within Ti-6Al-4V is more than 1250 m/s under such loading conditions. The temperature rise within ASB is also estimated to be T 2 ≈ 1460℃ based on energy balance. Such high temperature has led to softening of the material within the ASBs, and has intensified the shear localization and finally resulted in fracture of the material.     

Free vibration analysis of third-order shear deformable composite beams using dynamic stiffness method

The dynamic stiffness method is introduced to investigate the free vibration of laminated composite beams based on a third-order shear deformation theory which accounts for parabolic distribution of the transverse shear strain through the thickness of the beam. The exact dynamic stiffness matrix is found directly from the analytical solutions of the basic governing differential equations of motion. The Poisson effect, shear deformation, rotary inertia, in-plane deformation are considered in the analysis. Application of the derived dynamic stiffness matrix to several particular laminated beams is discussed. The influences of Poisson effect, material anisotropy, slenderness and end condition on the natural frequencies of the beams are investigated. The numerical results are compared with the existing solutions in literature whenever possible to demonstrate and validate the present method.