动力刚化问题的实验研究

应用频散可控耗散格式对环形激波在圆柱形激波管内绕射、反射和聚焦 的问题进行了数值模拟研究. 研究结果表明环形激波形成强烈聚焦的关键因素是环形激波在 圆柱形管道中向对称轴运动时，绕射激波就不断加速而不作通常情况下的衰减；不同马赫数 的环形激波绕射也产生不同马赫数及形状的准柱形激波，导致聚焦效果和位置的差异；另外， 环形激波聚焦于一个点而圆柱形激波聚焦于一条线,两者有本质不同.     

用环形激波聚焦实现爆轰波直接起爆的数值模拟

利用基元反应模型和有限体积法对环形激波在可燃气体中聚焦实现爆轰波直接起爆进行了数值模拟。研究结果表明，标准状态下的氢气-空气混合气体在马赫数为3.1以上的环形激波聚焦产生的高温高压区作用下会诱发可燃气体的直接起爆形成爆轰波，爆轰波与激波和接触间断相互作用产生了复杂的波系结构；爆轰波爆点位置在对称轴上并不是固定的点，而是随着初始激波马赫数的变化而发生移动；可燃气体初始温度和压力对起爆临界马赫数都有影响，但是初始温度的影响大得多。     

环形激波绕射、反射和聚焦流场的间断有限元模拟

采用间断有限元方法对环形激波在圆柱形激波管内绕射、反射和聚焦流场进行了数值模拟。将二维守恒方程的间断有限元方法发展到轴对称Euler方程,并对环形激波绕后台阶流动进行了数值计算。计算结果表明,采用间断有限元方法能够有效地捕捉运动激波在圆柱形激波管内传播的复杂流场结构;在聚焦点附近,数值解具有较大的梯度变化,表明该方法对间断解具有较强的捕捉能力,在聚焦点附近不会产生振荡或抹平间断现象。     

空气中平面激波同圆柱的非定常干涉

平面激波在圆柱上的反射与绕射是目前国内外研究激波非线性复杂现象的典型课題。近年来,Takayama(1987)在入射激波马赫数M_i=1.3及2.6的条件下,得到了在圆柱周围的激波绕射与反射的光测实验结果。众所周知,激波在圆柱上的反射与绕射是一非定常现象,为了了解和分析整个非定常过程的发展和变化,应得到圆柱后较远区域的结果。本文利用两次曝光全息激光干涉仪不仅得到了圆柱周围的波系图案,而且也得到了激波脱离圆柱后驻点后约10倍圆柱直径的范围内的流动形态。同时也给出了不同M_i条件下的三波点轨迹和入射激波与反射激波之间夹角ω随距离变化的实验结果。     

绕射激波和反射激波作用下N_2/SF_6界面R-M不稳定性实验研究

利用高速纹影测试实验研究低马赫数入射激波绕圆柱体后冲击N2/SF6平面界面,以及来自固壁的反射激波再冲击过程的(Richmyer--Meshkov,R--M)不稳定性特征.与平面激波作用不同的是,绕射后的激波会在界面处生成局部扰动.实验结果显示,入射激波作用下界面宽度增长缓慢,而反射激波再冲击后,局部扰动会产生大的"尖钉"和"气泡"结构;以及反射激波与边界层相互作用产生壁面涡,它们会加剧湍流混合区的增长;实验中反射激波过后混合区增长率不十分依赖于波前状态,增长规律同Mikaelian模型较吻合;来自尾部固壁的反射稀疏波会再次加剧湍流混合区的增长.     

可燃气体中激波与障碍物作用在下游形成爆轰波的数值研究

对平面激波和单个矩形障碍物作用的过程进行了数值模拟,研究了反射产生的上行爆轰波在下游可燃气体中形成爆轰波的过程。数值结果表明,下游爆轰波形成过程主要有2种模式:爆轰波直接绕射和绕射波在上壁面反射,这和已有的实验结果是一致的。通过研究下游爆轰波的形成过程受入射激波马赫数、混合气体的压力和管道尺度的影响,分析了上游爆轰波向下游传播的波动力学过程,讨论了2种形成过程的作用规律和控制因素,阐明了下游爆轰波的形成规律。     

激波驱动的气固两相流的动态压力测量

利用水平圆柱形激波管对激波驱动的可压缩性气固两相流进行了试验研究.利用压电式压力传感器、电荷放大器、示波器及计算机组成的压力信号测试系统, 对激波与颗粒作用前后的气相参数进行测量及分析. 试验中测得了激波在管中的传播速度, 波后气流的压力, 反射激波、透射激波的压力和速度等. 分别考察颗粒、装载比、驱动气源以及入射激波马赫数等因素的差异对气相参数的影响.试验结果表明: 激波与颗粒群相互作用时, 会产生反射激波和透射激波,其强度与驱动气源、颗粒大小、颗粒装载比等参数有关;激波衰减率随着装载比、马赫数的增大而减小. 研究指出,在颗粒群被激波加速的初始阶段, 颗粒间的弹性碰撞起着重要的作用.      

环形激波聚焦流场特性的数值研究

针对环形激波聚焦过程产生的高温、高压特性,采用间断有限元方法模拟了环形激波在同轴圆柱 形激波管内的聚焦流场特性。计算结果表明,采用间断有限元方法能够有效地捕捉激波聚焦过程形成的二次 激波、涡环、三波交点和球面双马赫反射等主要流动特征。此外,通过改变环形管道内外半径对聚焦流场进行 模拟发现,环形管道外径对中心轴线上聚焦峰值压力的大小和位置影响较小,环形管道内径对中心轴线上聚 焦峰值压力的大小和位置影响较大。计算结果可以为工程应用提供一定的理论指导。     

活塞式无膜激波管特性的实验研究

本文在自行研制的无膜激波管中，实验研究了不同快速卸压装置对该激波管运行特性的影响。通过控制高压段充气压力和测量压力波形，得到了高低压段压比和激波马赫数的关系曲线以及在测压点处形成激波所需的最低压比。实验结果表明排气快慢对激波形成距离和所形成激波的强度产生很大的影响。对不同装置产生的结果差异进行了一定的分析。     

沉积粉尘的激波点火

采用瞬态阴影技术及红外光电传感器技术实验研究了沉积玉米粉的激波点火过程，并对此进行了理论分析。实验与理论分析结果表明，激波掠射沉积粉尘床后，粉尘颗粒先上扬到一定高度后才点火，颗粒的点火延迟时间与激波波前马赫数、气相氧气含量等因素有关。另外，沉积粉尘的激波点火延迟时间比相同条件下的悬浮粉尘激波点火延迟时间长。     

Experimental study of toroidal shock wave focusing in a compact vertical annular diaphragmless shock tube

The paper reports results of experiments regarding toroidal shock wave focusing in a vertical shock tube as a part of a series of converging shock wave studies. This compact vertical shock tube was designed to achieve a high degree of reproducibility with minimum shock formation distance by adopting a diaphragmless operating system. The shock tube was manufactured in the Institute of Fluid Science, Tohoku University. An aspheric lens shaped cylindrical test section was connected at the open end of the shock tube to visualize the diffraction and focusing of the toroidal shock wave released from the ring shaped shock tube opening. Pressure transducers were flush mounted on the shock tube’s test section to measure pressure histories at the converging test section. Double exposure holographic interferometry was employed to quantitatively visualize the shock waves. The whole sequence of toroidal shock wave diffraction, focusing, and its reflection from the symmetrical axis were successfully studied. The transition of reflected shock waves was observed.     

Numerical investigation of toroidal shock wave focusing in a cylindrical chamber

In this paper, focusing of a toroidal shock wave propagating from an annular shock tube into a cylindrical chamber was investigated numerically with the dispersion controlled dissipation (DCD) scheme. The first case for an incident Mach number of 1.5 was conducted and compared with experiments for validation. Then, several cases were calculated for higher incident Mach numbers varying from 2.0 to 5.0, and complicated flow structures were observed. The numerical study was mainly focused on two aspects: focusing process and flow structures. The process, including diffraction, focusing, and reflection, is displayed to reveal the focusing mechanism, and the flow structures at different incident. Mach numbers are used to demonstrate shock reflection styles and focusing characteristics. PACS 47.40.Ki; 47.40.Nm; 52.35.Tc     

聚心火焰与激波相互作用的数值研究

基于带化学反应的2维轴对称Euler方程,利用带有monotonized centered(MC)限制器的波传播算法,在两端敞开的圆桶中对惰性介质的聚心激波和氢气-空气混合物的聚心火焰与激波的相互作用进行了数值模拟。数值结果表明,在惰性介质中激波在轴心的每次汇聚均可成长为马赫干,马赫干的追赶使激波得到一定程度的增强,但整体还呈下降趋势。在氢气-空气混合物中,燃烧诱导的激波,由于与火焰的反复作用,使激波在轴心处产生马赫干的频率和强度皆高于惰性介质中的情形。同时,火焰在与激波的相互作用过程中发生失稳变形,使其形状呈扁平头部的蘑菇云。     

Numerical investigation of axisymmetric shock wave focusing over paraboloidal reflectors

The problem of a plane shock wave incident to a paraboloidal reflector is numerically investigated. The numerical solver used is developed by an improved, implicit, upwind total variation diminishing scheme in a finite-volume approach. The real-gas effect is taken into account if high temperature occurs. The solver is validated on four test problems. The complicated flow fields of axisymmetric shock wave focusing for different-depth reflectors at various incident shock Mach numbers are studied. An interesting result of a maximum pressure happening at the reflector center is found. This is due to the occurrence of an implosion phenomenon. A maximum temperature might occur at the reflector center or at other locations, depending on the incident shock Mach number and the reflector depth. Moreover, vortical flows induced by shock wave focusing and their formation mechanism are explored. It was found that the vortices near the reflector are caused by a ring-shaped shock/slipline interaction. Owing to the slipline on the symmetry axis, a jet flow is induced, resulting in the formation of vortices near the symmetry axis. Received 13 January 1998 / Accepted 10 November 1998     

Focusing of weak shock waves in confined axisymmetric chambers

Theoretical study of a weak shock wave focusing process on a spherical region in confined 3-D axisymmetric chambers is presented. The chambers are elliptic or parabolic in the plane cross-section containing their axis of symmetry. In the elliptic case a spherical shock wave of constant strength generated at one of the focal points will reflect off the chamber wall and converge on a spherical region around the second focus of the chamber. It is shown that the pressure distribution on the converging spherical shock wave is not homogeneous. In the parabolic case two possibilities of shock generation are considered. In the first one a plane shock wave of constant intensity is send in the inner of the chamber. This shock wave with the plane perpendicular to the symmetry axis will after the reflection off the chamber wall transform to a spherical shock with non-homogeneous pressure distribution. Alternatively, a spherical shock of constant intensity generated at the focus of the paraboloidal chamber will after the reflection transform to a plane shock with non-homogeneous pressure distribution propagating in the outer of the chamber. The above mentioned problems are solved within the frame of the geometrical acoustics approximation and the flow fields as well as the non-uniform shock strengths behind the converging wave fronts are calculated.This article was processed using Springer-Verlag T_EX Shock Waves macro package 1.0 and the AMS fonts, developed by the American Mathematical Society.     

椭球罩作用下的水下爆炸冲击波反射聚焦模型

基于冲击波传播、非线性反射和聚焦理论,建立水下爆炸冲击波在椭球罩作用下的反射聚焦模型。讨论自由传播、壁面反射和定向聚焦阶段的冲击波特性和压力计算方法,利用波前和波法线的近似方程构建压力场的数值计算域,进而模拟聚焦过程,并与现有实验结果进行对比,结果表明:所建模型可为正聚焦压力提供满足工程精度的预测,并能描述水下冲击波及产生的拉伸波聚焦过程中的一些细节;椭球罩能有效地聚焦水下冲击波,在动力学焦点附近获得有效增益区,在近轴方向上明显削弱冲击波压力衰减;理想条件下的动力学焦点一般位于几何焦点之前,但实际的反射罩变形和背向位移将使其发生后迁,甚至能越过几何焦点。     

A holographic interferometric study of shock wave focusing in a circular reflector

A holographic interferometric study was made of the focusing of reflected shock waves from a circular reflector. A diaphragmless shock tube was used for incident shock Mach numbers ranging from 1.03 to 1.74. Hence, the process of reflected shock wave focusing was quantitatively observed. It is found that a converging shock wave along the curved wall undergoes an unsteady evolution of mach reflection and its focusing is, therefore, subject to the evolution of the process of shock wave reflections. The collision of triple points terminates the focusing process at the geometrical focus. In order to interprete quantitatively these interferograms, a numerical simulation using an Eulerian solver combined with adaptive unstructured grids was carried out. It is found numerically that the highest density appears immediately after the triple point collision. This implies that the final stage of focusing is mainly determined by the interaction between shock waves and vortices. The interaction of finite strength shock waves, hence, prevents a curved shock wave from creating the infinite increase of density or pressure at a focal point which is otherwise predicted by the linear acoustic theory.