环形板的非轴对称屈曲分析

本文利用打靶法研究了内外边界固支且在外边界受均匀径向压力作用下的极正交各向异性环形板的非轴对称屈曲和过屈曲,计算了临界载荷,讨论了分支解的存在性,得到了分支解的渐近表达式,分析了环形板的屈曲性态。     

环形板屈曲与过屈曲的横向剪切效应

本文应用分支理论和打靶法研究了环形板屈曲与过屈曲的横向剪切效应     

中面内边界条件对圆柱曲板弹性屈曲的影响

本文利用统一的三角级数,通过待定系数向量将矩形圆柱曲板的屈曲形态离散化,每个边界引入三个弹性边界约束参数,利用位能原理和反迭代法,确定均匀轴压、侧压、剪切及组合加载时曲板的分支屈曲临界载荷和屈曲形态,研究了在一些典型边界条件下曲率参数的影响,以及弹性边界条件时边界弹性参数的影响。     

具有压电材料弹性环形板的屈曲

对在不同位置粘有任意多对压电片的弹性环形板在电压和径向压力作用下的轴对称屈曲进行了研究．根据压电效应的等效作用量，初参数法以及传递矩阵方法得到了环板屈曲的特征方程．对不同位置及不同宽度的压电片，计算了结构的屈曲载荷．并得到了稳定性边界曲线．     

矩形薄板弹性稳定的一般解

本文求得了矩形薄板稳定屈曲微分方程的一般解,可以求解任意边界矩形薄板的稳定问题。以两邻边自由或平夹,另两边简支正方形板为例求解了四边匀压的临界载荷及其挠度.     

双参数地基圆(环)形板的边界剪力及其力学响应

针对目前考量双参数地基上圆形或环形板边界剪力中存在的一些不足,应用Hankel变换法求得双参数地基的解析解,研究了任意环状线荷载作用下双参数地基的挠度、转角及地基反力间的关系。指出双参数地基在线荷载处的转角差与表示横向联系的地基参数之乘积等于线荷载集度;环内的分布荷载仅影响环内侧转角,而环外分布荷载也仅影响环外侧转角;进而又给出了适用于双参数地基圆形或环形板的内/外边界剪力的简明表达式。最后分别给出了双参数地基上自由边界圆形薄板中点承受集中力、圆形均布荷载作用时边界剪力对板中点挠度、弯矩的影响规律;双参数地基边界剪力对板挠度、弯矩有较明显影响,尤其是板的相对半径ρ_04或是荷载距板边界较近时这种影响更为明显。     

冲击载荷作用下矩形薄板的弹性动力屈曲

为了研究冲击载荷作用下考虑应力波效应弹性矩形薄板的动力屈曲,根据动力屈曲发生瞬间的能量转换和守恒准则,导出板的屈曲控制方程和波阵面上的补充约束条件,真实的屈曲位移应同时满足控制方程和波阵面上的附加约束条件。满足上述条件,建立了该问题的完整数值解法,对屈曲过程中冲击载荷、屈曲模态和临界屈曲长度之间的关系进行研究,定量计算了横向惯性效应对提高薄板动力屈曲临界应力的贡献。研究表明:板的厚宽比一定时,临界屈曲长度随冲击载荷的增大而减小;由于屈曲时的横向惯性效应,应力波作用下薄板一阶临界力参数是相应边界板的静力失稳临界力参数的1.5倍;随着边界约束逐渐减弱,板临界力参数逐渐减小,动力特征参数逐渐增大。     

环扇形悬臂板的弯曲问题

本文对受有边界集中载荷的环形悬臂板提出了一个解析解。求解的方法是采用曲线坐标变换,两次求解相应的调和方程,推导出解的一般形式。然后利用边界条件确定通解中的待定常数。本文的方法完全通用于求解环扇形板任意边界条件下的弯曲问题。文中给出了数字实例。其理论结果与激光散斑法求得的实验值是一致的。     

各向异性矩形板的剪切屈曲分析

根据各向异性矩形薄板剪切屈曲横向位移函数的微分方程建立了一般性的解析解。该一般解包括三角函数和双曲线函数组成的解,它能满足四个边为任意边界条件的问题;该一般解还包括代数多项式解,它能满足四个角的边界条件问题。因此,这一解析解可用于精确地求解任意边界的各向异性矩形板的剪切屈曲问题。其中待定常数可由四边和四角的边界条件来确定,由此得出的齐次线性代数方程系数矩阵行列式等于零可以求得各阶临界载荷及其屈型。结合配点法,利用变形的对称和反对称性,以及对称迭层正方形板均可使计算更简单。以四边平夹的对称角铺设复合材料迭层板为例进行了计算和讨论。     

联合载荷作用下简支矩形板的屈曲和过屈曲

本文研究了简支正交各向异性矩形板在两对板受中面压力作用下的屈曲和过屈曲性态,得到了载荷的稳定性区域,证明了临界载荷最多为二重的。利用多参数摄动方法求得临界载荷附近板的过屈曲状态的渐近解,分析了在二重临界载荷附近,当载荷按比例变化时,板的可能的过屈曲状态及其与参数的依赖关系。     

Stability of an annular plate of a shape memory alloy

Analytical solutions using various hypotheses are obtained for the problem of buckling of an annular circular plate of a shape memory alloy in the forward or reverse thermoelastic phase transformations under uniform radial compression. It is established that, despite the axial symmetry of the body geometry, loads, and boundary conditions, the minimum critical loads for annular plates correspond to nonaxisymmetric buckling modes, in contrast to continuous plates.     

Elastic instability of a uniformly compressed annular plate with axisymmetric initial deflection

This paper presents a theoretical study of the elastic instability of a uniformly compressed, thin, circular annular plate with axisymmetric initial deflection. The dynamic version of the nonlinear Marguerre plate theory is used, and the linear free vibration problems around the axisymmetric finite deformation of the plate are solved by a finite difference method. By examining the frequency spectrum with various asymmetric modes, the critical compressive load under which the axisymmetric additional deformation of the plate becomes unstable due to the bifurcation buckling is determined, which is found to depend severely on the magnitude of the axisymmetric initial deflection.     

环形薄板轴对称非线性屈曲的样条函数解法

环形薄板的大挠度计算因为边界条件复杂,仅有少数特殊情形的数值解答。均布边缘径向力作用下环形薄板非线性屈曲迄今尚未有研究成果。作者以三次B样条函数为试函数,用配点法计算环形薄板的大挠度。在12种不同的边界条件下,首次计算了环形薄板的压曲临界荷载及超临界荷载作用的变形。在所有的算例中均取得了收敛的数值结果。结果表明样条配点法具有收敛范围大、精度高和计算时间少的优点。     

安全壳中钢衬壳热屈曲问题理论与实验研究(Ⅱ)──实验部分

钢衬壳热屈曲问题是核工程安全壳设计中的主要问题,但实验研究方面的文章发表得不多文中以200兆瓦核电站安全壳中钢衬壳为研究对象,采用局部1：1模型,测得了钢衬壳热屈曲温度和应变载荷,给出了钢衬壳屈曲和初始后屈曲过程中挠度和温度关系、以及膜应变和温度关系,实验测得钢衬壳具有局域屈曲的现象,实验屈曲载荷与理论结果符合较好     

An analytical solution for buckling of moderately thick functionally graded sector and annular sector plates

In this article, an analytical solution for buckling of moderately thick functionally graded (FG) sectorial plates is presented. It is assumed that the material properties of the FG plate vary through the thickness of the plate as a power function. The stability equations are derived according to the Mindlin plate theory. By introducing four new functions, the stability equations are decoupled. The decoupled stability equations are solved analytically for both sector and annular sector plates with two simply supported radial edges. Satisfying the edges conditions along the circular edges of the plate, an eigenvalue problem for finding the critical buckling load is obtained. Solving the eigenvalue problem, the numerical results for the critical buckling load and mode shapes are obtained for both sector and annular sector plates. Finally, the effects of boundary conditions, volume fraction, inner to outer radius ratio (annularity) and plate thickness are studied. The results for critical buckling load of functionally graded sectorial plates are reported for the first time and can be used as benchmark.     

平动柔性矩形薄板的动力学特性与屈曲分析

应用Hamilton变分原理建立了平动状态下对边简支对边自由矩形薄板的非线性动力学方程,分别应用假设模态法和康特洛维奇法分析了板的前4阶近似振动频率、临界分岔值及板的前3阶后屈曲近似解,并比较了取不同阶数假设模态对分析结果的影响．分析表明整体平动可使柔性多体系统中的柔性构件产生动力刚化和动力软化效应,且软化效应还可使系统平衡位置发生分岔而失稳;在动力刚化和动力软化情况下,柔性构件模态出现的顺序均可能发生改变,此性质在柔性多体系统动力学简化建模特别是模态截断时应引起足够的重视．     

Multiple buckled states of rectangular plates

We consider the buckling of a simply supported plate subjected to a constant edge thrust λ. The aspect ratio l is such that the critical thrust (the first bifurcation point of the associated non-linear eigenvalue problem) is of multiplicity two. A study of the non-linear static problem indicates that there are nine possible equilibrium states. One of these corresponds to the unbuckled state while the remaining eight represent buckled states. A linear stability analysis and a calculation of the potential energy of each of the static solutions indicates that four of the solutions are stable and five are unstable.     

Supercritical and subcritical buckling bifurcations for a compressible hyperelastic slab subjected to compression

We study the buckling bifurcation of a compressible hyperelastic slab under compression with sliding–sliding end conditions. The combined series-asymptotic expansions method is used to derive the simplified model equations. Linear bifurcation analysis yields the critical stress value of buckling, which gives a non-linear correction to the classical Euler buckling formula. The correction is due to the geometrical non-linearities coupled with the material non-linearities. Then through non-linear bifurcation analysis, the approximate analytical solutions for the post-buckling deformations are obtained. The amplitude of buckling is expressed explicitly in terms of the aspect ratio, the incremental dimensionless engineering stress, the mode of buckling and the material constants. Most importantly, we find that both supercritical and subcritical buckling could occur for compressible materials. The bifurcation type depends on the material constants, the geometry of the slab and the mode numbers.