正交异性钢桥面板轮载横向效应的解析分析方法

在分析正交异性钢桥面板构造特点的基础上,将轮载影响范围内的桥面板简化为弹性支撑的平面框架,建立了正交异性钢桥面轮载横向效应的解析分析模型,推导了纵肋弹性支撑刚度和车轮荷载集度等效计算方法,提出了桥面板与U肋交接位置处横向弯曲应力的解析公式,讨论并明确了影响桥面板横向弯曲应力峰值的关键敏感影响因素,并以某钢箱梁为例证明了本文算法的合理性。研究发现,本文方法计算得到桥面板与U肋相交位置的横向应力值与有限元结果相差不超过10%,证实了本文算法的正确性,也为正交异性钢桥面的初步设计提供了极大的方便;正交异性钢桥面板的横向轮载应力随U肋厚度和高度增加而增大,但随顶板厚度和横隔板间距增大而减小;相对而言,顶板内横向拉应力受顶板厚度的影响最为显著,对腹板倾角和U肋腹板厚度的变化并不敏感。     

新型混凝土桥面铺装材料的冲击力学性能

利用大尺寸Hopkinson压杆对新型混凝土桥面铺装材料钢纤维增强聚合物改性混凝土（steel fiber reinforced and polymer modified concrete,SFRPMC）进行了冲击实验,并且在相同基准配合比下,与普通混凝土、钢纤维混凝土的冲击性能进行了对比。观察了不同打击速度下三种材料的破坏形态,得到了在不同应变率下的应力应变关系,比较了三种材料的应变率敏感性,最后从机理上分析了掺加钢纤维和聚合物对混凝土材料冲击力学性能的影响。结果表明,钢纤维增强聚合物改性混凝土材料具有良好的冲击韧性,是一种理想的混凝土桥面铺装材料。     

埋光纤光栅传感器智能土木结构应变监测

采取与土木工程施工特点相适应的操作工艺与保护方法，将光纤Bragg光栅传感器埋入钢筋混凝土结构中，分别在实验室和实际工程施工现场对混凝土内部的应变进行了测量。实验中光纤Bragg光栅传感性能良好，能够监测混凝土内部应变状态，显示出成活率高、绝对值测量、寿命长等优势，为建立基于光纤传感器的结构健康监测系统奠定了基础。     

静动组合载荷下混凝土率效应机理及强度准则

混凝土结构在受到动载荷作用之前,通常已承受着初始静载荷的作用.大量关于混凝土应变率效应的研究均没有考虑初始静载荷对动强度的影响,会导致过高地估计混凝土的动强度,使混凝土结构设计偏于危险.本文通过分析混凝土材料在静动组合载荷下的率效应机理,给出了初始静载荷的定义.在此基础上,推导了混凝土材料参数与初始静载荷和应变率的表达式,提出了建立静动组合强度准则的一般方法.通过材料参数反映初始静载荷与应变率的联合影响,给出了由初始有效静载荷、动态黏聚强度和摩擦强度共同组成的混凝土动态强度,将广义非线性强度准则发展为静动组合多轴强度准则.建立的强度面在相同初始静载荷下随应变率的增大向外扩张,在相同应变率下随初始静载荷的增大向里收缩,即混凝土的强度在相同初始静载荷下随应变率的增大而增大,在相同应变率下随初始静载荷的增大而减小.此外,当初始静载荷和应变率不变时,加载路径对混凝土材料的应变率效应无影响,但会影响混凝土材料的静水压力效应,即当初始静载荷和应变率固定不变时,静动组合强度面的位置和大小即可确定,不同加载路径下强度的不同是由于静水压力效应导致的.最后利用多组混凝土材料静动组合强度试验对建立的静动组合强度准则进行了验证.     

Full-field strain measurement using a luminescent coating

In this paper we describe an optical-based technique, called strain sensitive skin (S³), for measuring in-plane strain data on structural members under static load. The technique employs a coating consisting of a luminescent dye and polymer binder that is applied to the surface of a test part via conventional aerosol techniques. Proper illumination stimulates the dye, which in turn emits higher wavelength luminescence. The excitation and emission intensities have different wavelengths; therefore, enabling optical filtering to separate the two signals. The optical strain response is intensity based. A network of randomized microcracks within the binder scatters the waveguided luminescence from the excited dye molecules. The amount of scattered luminescence is related to the changes in the microcrack openings and orientations via mechanical strain. Various calibration tests show the optical strain response to be proportional to the sum of in-plane principal strains. With this new experimental testing tool, full-field high-resolution strain measurements can be acquired. The optical strain response of this new sensor is minimally dependent on viewing and lighting directions, rendering the technique viable to imaging and determining strain fields for three-dimensional complex geometries.     

一种轿车车轮应力状态测量与分析方法

基于台架应变测试试验方法,研究轿车车轮在疲劳试验中的应力状态。结果表明:车轮的径向疲劳试验时,轮胎会对车轮的载荷产生较大的影响,轮胎与转鼓的挤压变形以及正反转动都会对车轮的应力状态产生影响;车轮径向疲劳试验时,最大应变出现在轮辋与轮胎接触位置沿车轮圆周方向,而在靠近轮心位置的应变较小;车轮弯曲疲劳试验时,最大应变出现在轮辐靠近轮心的位置,最大应变出现在轮辐的长度方向;不同的载荷对车轮应变的变化规律并没有影响,但是会对最大和最小峰值产生影响。     

钢质套筒被动围压下混凝土材料的冲击动态力学性能

为了研究混凝土材料在钢质套筒侧限约束下的动态力学性能参数和破坏规律,采用分离式大直径（75 mm）SHPB实验技术,测试了钢质套筒侧限约束下不同混凝土试件在不同载荷作用下轴向或径向的应力、应变峰值,平均应变率,计算了混凝土材料的损伤值,描述了加载破坏现象,对实验结果进行了分析。结果表明:混凝土材料在被动围压下,延性、抗破坏能力得到加强,具有明显的增强效应。被动围压下SHPB实验中混凝土材料的破坏应变为典型SHPB实验中破坏应变的1.8～2.8倍;破坏应力达到150 MPa以上,为静力学无围压条件下的2～5倍。     

变刚度梁弯曲解析解在桥面板中的应用

针对新型连续窄幅钢箱梁-混凝土组合桥梁,研究了该桥型桥梁的桥面板拉应力控制方法与措施．将该桥型组合桥梁等效为可变刚度的Euler梁,给出任意横向荷载作用下变刚度梁的静力弯曲解析通解,并得到三跨连续阶梯型变刚度梁变形及其内力分布特征．在此基础上,以三跨连续窄幅钢箱梁-混凝土组合桥梁为研究对象,考虑下部钢箱梁与上部混凝土桥面板完全剪力连接,通过改变负弯矩区钢箱梁壁厚、内部充填混凝土的强度、长度与高度等参数,分析得到可有效控制桥面板拉应力的关键因素．结果显示：在负弯矩区段内的钢箱梁内部充填混凝土对控制该区域混凝土桥面板拉应力效果明显,但混凝土强度影响较弱．混凝土桥面板开裂区域随钢箱梁中充填混凝土长度的增加而减少,但桥面板顶部拉应力会随混凝土充填高度的增加呈现先减小后增大的趋势,在充填高度为箱梁内部净高的20 %~30 %左右时效果较为显著,此时经济效益最佳．     

Field measured pre-stress concrete losses versus design code estimates

In Florida, pre-stressed concrete bridges with a hybrid structural configuration, consisting of simply supported girders and continuous deck units providing composite action, are prevalent. In this study, an actual bridge with this configuration is instrumented with embedded vibrating wire strain gages during construction. The axial strain data are utilized to determine the time-dependent pre-stress loss variation and distribution in the pre-tensioned concrete girders used for the bridge. In this paper, however, we discuss the bridge instrumentation and monitoring technique used, and the deduced pre-stress losses obtained from field-measured strains up to 150 days, before placement of the composite slab. A comparison of the measured loss with the estimates of the Precast/Prestressed Concrete Institute (PCI) and the American Association of State Highway and Transportation Officials (AASHTO) indicates that the field-measured pre-stress loss is non-uniform across the girder depth, opposed to a uniform distribution implicitly assumed in most codes. The measured pre-stress variation is used in computing the concrete stress distribution in the girder at different depths within the given cross-section. When compared to the concrete stress from using the PCI and AASHTO suggested losses, the stress distribution resulting fron using the field-measured loss is found to be non-linear, and in most cases higher.     

光纤光栅传感器对钢筋混凝土内部应变的测量及温度效应的研究

本文应用光纤光栅传感器实现了对钢筋混凝土试件内部应变的测量．试验不仅就应用光纤光栅进行混凝土结构内部应变测量的技术、工艺进行研究，还通过设计温度控制试验，考察了光纤光栅传感器的温度补偿问题，以及横向应变对测量结果的影响．     

考虑混凝土应变率变化的高拱坝非线性动力响应研究

提出一种新的应变率相关的混凝土非线性弹塑性损伤模型。采用此模型对混凝土拱坝的非线性地震响应作了分析。在综合考虑坝-地基-库水动力相互作用和坝缝非线性接触的基础上，着重研究了混凝土应交率相关效应及加载历史对混凝土极限强度等重要参数及拱坝响应的影响，并与采用不考虑应交率影响的混凝土损伤模型计算结果进行了对比分析。结果表明，拱坝考虑横缝作用后的坝面应变率分布不同于整体拱坝。应交率分布形态不仅可以很好地表征拱坝的振动形态，而且对于高拱坝的动力响应的影响也不可忽略。     

BOTDR分布式检测技术在复杂地层钻孔灌注桩测试中的应用研究

分析了Kagome格栅的等效刚度和屈服面. 其屈服面奇异,由4段直线围成. 利用该屈服面, 估算了Kagome具有I型、II型半无限大裂纹的裂尖塑性区,有限元计算验证了解析预测的 准确性. 与奇异屈服面相比,由Mises光滑屈服面给出的塑性区误差较大. 因此只有弹性情 况,可以将Kagome等效为各向同性;若材料塑性,或应力场奇异性较强,Kagome的强度依 赖于主应力方向,不能用各向同性模型来描述.     

Experimental Investigation of Wheel/Rail Rolling Contact at Railhead Edge

Wheel-rail rolling contact at railhead edge, such as a gap in an insulated rail joint, is a complex problem; there are only limited analytical, numerical and experimental studies available on this problem in the academic literature. This paper describes experimental and numerical investigations of railhead strains in the vicinity of the edge under the contact of a loaded wheel. A full-scale test rig was developed to cyclically apply wheel/rail rolling contact load to the edge zone of the railhead. An image analysis technique was employed to determine the railhead vertical, lateral and shear strain components. The vertical strains determined using the image analysis method have been validated with the strain gauge measurements and used for the calibration of a 3D nonlinear Finite Element Model (FEM) that simulates the wheel/rail contact at the railhead edge and use suitable boundary conditions commensurate to the experimental setup. The FEM was then used to determine other states of strains.     

干燥和饱和混凝土动态力学特性及其机理

采用分离式Hopkinson杆装置,对混凝土进行干燥和饱和状态下的SHPB实验,并与准静态实验进行对比。结果表明:干燥和饱和混凝土均具有明显的应变率效应,中等应变率条件下的应力应变曲线上升段比准静态的曲线陡;饱和混凝土动态强度提高的幅度接近干燥混凝土的2倍,具有更强的应变率敏感性;存在一个应变率临界值,仅当应变率大于临界值时,饱和混凝土的动态强度才大于干燥混凝土的的动态强度;基于实验结果,给出了不同饱和度混凝土强度与应变率的关系。     

Circumferential strain measurement for a concrete cylinder in uniaxial compression by a fiber optic sensor

This paper deals with circumferential strain measurement for concrete in uniaxial compression by using a fiber optic sensing system. A fiber optic sensing system was employed to measure the elongation of the optical fiber for a cylindrical concrete specimen in uniaxial compression by using white light interferometry. A theoretical model describing the relationship between the elongation of the fiber glass and the circumferential strain of cylindrical concrete specimen in uniaxial compression is proposed. Some tests were performed to verify the measurement method. The results indicate that the proposed method is valid.     

Prediction of wheel performance by analysis of normal and tengential stress distributions under the wheel-soil interface

Prediction of wheel performance by analysis of normal stress distribution under the wheel-soil interface was reported by one of our research members. In this study analysis of both normal and tangential stress distributions are included for the prediction of wheel performance. A visco-elastic soil model based on a three-element Maxwell model is used to evaluate normal stress distribution under a wheel running on soft ground. The values of the parameters characterizing the visco-elastic behavior of the soil can be derived from plate penetration tests. A rigid wheel-soil interface model is used to evaluate the tangential stress distribution under the wheel-soil interface. Shear deformation modulus, cohesion and angle of internal shearing resistance of the soil are derived from shear-displacement tests. Test results indicate that both maximum normal and shear stress occur in front of the wheel axle, and the location of peak normal stress shifts backwards towards the wheel axle while that of tangential stress shifts forwards when slippage is increased from a low value. Increasing slippage also causes a decrease in normal stress and an increase in tangential stress. Coefficients of traction and tractive efficiency are low at low slippage, increase with an increase in slippage, and level off at higher slippage.     

锈胀开裂后变形钢筋与混凝土粘结性能实验研究

为研究锈胀开裂对变形钢筋与混凝土间粘结性能的影响,开展了电化学快速锈蚀内贴应变片钢筋混凝土试件的拔出实验,得到了不同位置处钢筋的应变,进而推导了钢筋与混凝土不同位置处的粘结应力,分析了锈胀裂缝宽度对钢筋与混凝土间不同位置处粘结应力的影响。实验研究表明:粘结试件中的钢筋应变对锈胀裂缝宽度的敏感性大;对于锈胀裂缝较小的试件,其粘结应力峰值接近加载端,而对于锈胀裂缝较大的试件,粘结应力峰值更靠近自由端。     

沥青混凝土面板低温疲劳破坏的实验研究

我国北方地区的土石坝和水池的防渗沥青混凝土面板,常出现低温裂缝。因此,对沥青混凝土在低温条件下的温度应力疲劳进行实验研究很有必要.本项研究研制了适用于沥青混凝土低温低周大变形的弯曲疲劳试验机,进行了沥青混凝土在不同低温下的疲劳破坏性能试验。对试验结果用粘弹性理论和推广的应变区分法(SRP)和应变能区分法(SEP)进行了分析,首次得出了沥青混凝土的疲劳寿命与弯曲应力、应变和应变能的关系,并试用于实际工程的予测.     

基于抗压强度推测的水工混凝土疲劳残余应变研究

提出一种使用混凝土破坏前的应力应变发展曲线, 来推求混凝土抗压强度和 峰值应变的方法. 经过试验验证, 该方法具有较高的精度, 并可以得到疲劳试 验时真实的应力水平. 在MTS 810 TestStar材料试验系统上对C15水工混凝土开 展了受压疲劳试验. 通过试验数据分析, 得到疲劳残余应变发展规律公式、疲劳 失稳判据、疲劳寿命估算式及疲劳强度等, 对水工建筑物 的疲劳损伤分析与评定具有指导意义.     

图像相关法在高分子材料拉伸性能研究中的应用

本文对聚碳酸酯(PC)和丙烯腈丁二烯苯乙烯(ABS)的合金(PC/ABS)高分子材料不同环境温度下的拉伸性能进行了试验研究。根据图像相关分析法编制了图像法位移测量分析软件,并对该分析软件的适用性进行了分析。系统研究了PC/ABS高分子材料拉伸试验时三个方向的位移场和应变场。根据测得的位移场研究了该高分子材料拉伸过程中应变和应变率的变化以及应力应变变化规律,并对试验结果进行了详细分析。结果表明,文中采用的图像法位移测量系统具有较高的测试精度;拉伸过程中,试件厚度方向的收缩变形大于宽度方向的收缩变形;颈缩过程区具有非常高的应变率,颈缩后的平直颈缩区的应变率快速下降到一个很低的应变率继续缓慢变形;尽管载荷位移曲线出现了较大的载荷下降现象,PC/ABS拉伸时的真应力应变曲线没有明显的应力下降现象出现,因此,载荷下降现象主要由颈缩时的截面减小引起;高分子材料PC/ABS的屈服应力随环境温度的升高而降低。