一种改变光纤光栅布喇格波长的有效方法

本文报道了一种改变光纤光栅布喇格波长的有效方法。写于我氢光纤上的光纤光栅经过高温退火后,再利用紫外激光对其进行均匀曝光,不但能够有效改变其布喇格波长,而且还可以提高其反射效率。此种方法能很好地解决光纤光栅制作过程中的工作波长控制问题。     

探测氢气泄漏的布拉格光栅型传感器

介绍了布拉格光栅型氢传感器的工作原理,开发出一种新型的由布拉格光栅和溅射钯膜组成的氢气敏光纤传感器。分析了此传感器的应力传递过程,建立了最大波长漂移量与氢浓度关系的数学模型。通过试验研究了光栅的氢响应特性,理论模型预测的最大波长漂移量与试验结果十分吻合。     

Optical fiber Bragg grating hydrogen sensor based on evanescent-field interaction with palladium thin-film transducer

Fiber Bragg grating (FBG) sensors in single-mode optical fibers are widely applied for measurement of temperature and strain. If exposing FBG sensors to an external analyte by planar side-polishing technique of the fiber, evanescent-field interaction yields a Bragg wavelength shift also by changing the refractive index of the analyte. Deposition of sensor-specific transducer layers on the side-polished fiber can specify this spectrally encoding and network-capable optochemical fiber Bragg grating refractometry to the monitoring of specific substances, absorbed gases and vapors. In this paper, the sensor principle is demonstrated for the example of a hydrogen gas sensor based on a palladium thin-film transducer. Hydrogen in 0.1–4% volume concentration range can be monitored by the spectral shift of the Bragg wavelength, which is caused by the decreasing complex refractive index of Pd with increasing absorption of hydrogen.     

Characteristics of Fused Optical Fiber Grating Couplers with Tapered Shapes

Fused optical fiber grating couplers (FGCs), in which Bragg gratings are written in the coupling regions of fused optical fiber couplers with tapered shapes along them are theoretically and experimentally investigated. By coupled mode analysis considering these tapered shapes, the drop efficiencies of the FGCs, which are inherently zero for the normal fiber couplers without grating, are calculated. The grating offset, which is the difference between the centers of grating and the coupler taper, is found to be effective to increase the drop efficiency of the FGC. It is determined that the tapered shapes influence the wavelength dependence of the drop efficiency and tolerate the grating offset precision. Apodizations for the grating of FGC are found to be effective in suppressing side lobes of the drop efficiency. Measurement of the wavelength characteristics of drop efficiency and the temperature characteristics of drop wavelength of the fabricated fused FGC confirm that the lightwave with specific wavelength can be dropped by the FGC and that the temperature dependence of the drop wavelength is similar to that of Bragg wavelength changes of usual fiber Bragg gratings.     

采用WDM技术的光纤Bragg光栅传感网络

采用绝对测量原理的波长调制技术,光纤Bragg光栅可组成并行、串行和阵列WDM拓扑结构.分析表明,光纤Bragg光栅网络的工作原理类似于一个多宽带平面镜.利用光谱仪可测量上述光纤Bragg光栅网络的反射谱,其中,光源是宽带为～40nm的掺饵光纤放大器.当网络中的光纤Bragg光栅受扰动后,受扰光栅的反射谱发生相应的变化,即Bragg波长发生相应的偏移.结果表明,当事先确定了光纤光栅的波长调制范围,反射的峰值波长能反应光纤光栅传感网络的信息.值得注意的是～3nm的波长调制范围可满足～100℃和～2000με的参量测量.     

High-sensitivity temperature sensor based on Bragg grating in BDK-doped photosensitive polymer optical fiber

A single-mode polymer optical fiber (POF) with highly photosensitive core doped with benzil dimethyl ketal (BDK) is fabricated and used for writing Bragg grating through the two-beam interference method. The Bragg wavelength of the grating is about 1570 nm, while the full-width at half-maximum (FWHM) of the reflection peak is 0.3 nm. The temperature response of POF Bragg grating is theoretically analyzed and experimentally measured in contrast to silica optical fiber Bragg grating (FBG). The result shows that the temperature character of POF Bragg grating is negative, which is opposite to the silica optical FBG. The absolute value of the temperature response of POF Bragg grating is one order of magnitude higher than that of the silica optical FBG, making POF Bragg grating appear to be very attractive for constructing temperature sensors with high resolution.     

非线性二次曝光法制作三角形光纤Bragg光栅

提出了一种利用非线性二次曝光技术制作三角形光纤Bragg光栅的新方法.该方法只使用普通Bragg位相模板,采用两次曝光技术,通过控制光纤光栅的本地谐振波长和反射率,达到控制光纤光栅谱形的目的.第一次直接对光纤曝光,用来控制光纤光栅谐振波长;第二次通过位相模板曝光,用来控制光纤光栅的反射率.考虑到光敏光纤感光特性曲线的多项e负指数变化规律,按照"分步写入光纤光栅设计软件"进行曝光分布设计,利用"分步曝光光纤光栅写入系统"进行曝光控制,使用信息产业部第46研究所生产的DCS-01型光敏光纤,得到了线性范围1.24 nm、反射率为0～64%的三角形光纤Bragg光栅.三角形光纤Bragg光栅作为光纤光栅传感解调器件,在光纤传感领域具有重要应用价值.     

基于色散补偿光纤的高速光纤光栅解调方法

本文提出并论证了一种光纤光栅高速解调的新方法, 利用色散补偿光纤的色散效应, 将光纤光栅的波长漂移信息转换成时域信息. 采用脉冲激光器作为光源, 仅需一个光脉冲可获取单根光纤上所有光纤光栅的反射光脉冲, 再根据各个光栅反射回光脉冲的延时变化即可实现波长的解调. 本方法可用于准分布光纤光栅传感网络解调, 系统采用全光纤结构, 无需波长扫描, 大大提高了解调速度. 本文搭建了测试系统进行实验验证, 对3个光纤光栅组成的准分布式传感网络进行了解调, 实验结果表明, 解调出的光纤光栅布喇格波长线性度好, 解调速度最高可达1 MHz, 采样数据取10次平均后解调线性度可达0.9969, 解调误差约为27.8 pm.     

A unidirectional room temperature multi-wavelength fiber ring laser without isolator

A simplified ring cavity for achieving a unidirectional room temperature multi-wavelength erbium-doped fiber ring laser without optical isolator is demonstrated. The fiber ring cavity is built in such a way that the optical fields propagating in two directions suffer different losses caused by one sampled fiber Bragg grating. Furthermore, simultaneous multi-wavelength lasing with 0.8-nm intervals is demonstrated with sinusoidal phase modulation just before the sampled fiber Bragg grating to prevent single-wavelength lasing and unstable wavelength oscillation.     

+1/-1相位掩模板和532nm激光下低损耗As_2S_3硫系光纤布喇格光栅的制备

采用改进型Sagnac干涉光栅写入系统,利用532nm准带隙光曝光源和带+1/-1衍射级的相位掩模板,在两种不同直径的低损耗As_2S_3硫系玻璃光纤上刻写布喇格光栅,并研究曝光期间光栅的动态特性.实验表明,As_2S_3光纤布喇格光栅透射峰值随光纤直径的减小而增强;在曝光过程中,布喇格波长先是较快地向短波长方向移动,随着曝光时间的延长,布喇格波长缓慢地向长波长方向回复.曝光时间为800~1 000s时,在包层直径为140μm的As_2S_3光纤上获得质量良好的布喇格光栅光谱,其透射峰值可达-2.6dB,带宽为0.37nm.对As_2S_3硫系光纤纤芯的光敏性分析结果表明,折射率调制幅度和平均折射率变化随曝光时间分别可达到10-4和10-3数量级.     

Demonstration of an all-optical switching operation using an optical fiber grating coupler

An optical fiber grating coupler (FGC) is a fused optical fiber coupler with a tapered region in which refractive index-modulated gratings are written. In the FGC, the light with specific wavelength satisfying the Bragg condition of the grating can be dropped to one output port and other lights are transmitted to another output port when lights with various wavelengths are launched into the input port. The FGC can operate as an all-optical switch by controlling the Bragg wavelength of the grating using a third order nonlinear optical effect caused by a control light that are launched with a signal light. In this paper, an all-optical switching operation due to a third order nonlinear optical effect in an FGC is first demonstrated for a signal light with 1.55 μm-wavelength to be changed from one port of the FGC to another one by the 720 W peak of a control light from a Nd:YAG laser with 1.06 μm-wavelength. The switching efficiency obtained was 7%. It was clarified that a longer pulse length of the control light compared to the grating length is required to obtain a large Bragg wavelength shift for the switching. It was also clarified that the Bragg wavelength shift is caused by a third order nonlinear effect and a photothermal effect. A contribution of the photothermal effect was estimated. We also estimated the switching efficiency for pump power in the FGC switch.     

光纤光栅激光器激射波长的研究

一般认为，用光纤光栅作选频元件的光纤激光器，激射波长与光纤光栅中心反射波长一致，本文报道了不同的实验研究结果。通过细致的实验研究，发现光纤光栅激光器激射波长相对于光纤光栅中心反射波长有一定的偏移。激射波长可以出现在光栅中心反射波长的长波端，也可以出现在其短波端。对不同腔结构的掺镱、掺铒光纤光栅激光器的深入研究证明，谐振腔的各向异性对激光器的激射波长偏移起到决定性的作用，波长最大偏移量主要受限于光纤光栅的反射带宽。通过激光腔内的偏振控制器改变谐振腔的各向异性，可以在光纤光栅的反射带宽内控制激射波长的位置。     

镀镍光纤Bragg光栅温度传感特性实验研究

在光纤智能金属结构材料中,为了保护光纤Bragg光栅并使得传感器与基体金属有很好的结合性,在光纤Bragg光栅表面化学镀镍,并实验研究了化学镀镍前后的光纤Bragg光栅的温度传感特性.实验表明：镀镍后的光纤光栅的Bragg波长随温度变化呈现出良好的线性和重复性,Bragg光栅温度灵敏度变大.     

基于单个光纤光栅的Sagnac干涉仪的理论与实验研究

提出了一种结构新颖的Sagnac干涉仪,分析计算了所含光纤光栅分别为均匀Bragg光栅和线 性啁啾光栅时的透射响应,得到了均匀光栅Sagnac环的解析解,发现含均匀光栅时可得到间隔均匀的通带结构,而含啁啾光纤光栅时只能得到间隔非均匀的通带结构.这两种结构都可 能有应用价值,前者可用在密集波分复用系统中,后者可用在光纤传感领域中.实验制作了 两种通带间隔不同的、通带数分别为8和16的多通带滤波器,实验证实了理论计算得到的结果. 关键词： 光纤光栅 Sagnac干涉仪 光学滤波器     

基于光纤侧边抛磨技术的醋酸浓度光纤传感器

演示了两种利用光纤侧边抛磨技术制备的用于醋酸浓度检测的光纤传感器.其中一种光纤传感器采用轮式抛磨法对光纤光栅的光栅区包层进行侧边抛磨加工而成,将醋酸溶液覆盖于光纤光栅的抛磨区,利用侧边抛磨光纤光栅反射峰波长的变化对醋酸浓度进行测量;另一种光纤传感器采用轮式抛磨法对普通单模光纤包层进行侧边抛磨加工而成,将醋酸溶液覆盖于光纤抛磨区,利用抛磨光纤插入损耗的变化对醋酸浓度进行测量.两种光纤传感器的实验都表明:光纤包层抛磨表面与纤芯的距离越小,测量分辨率越高.剩余包层厚度为 0 μm 的侧边抛磨光纤光栅传感器测量醋酸溶液浓度分辨率为6.67%;剩余包层厚度为O.5μm 的侧边抛磨光纤传感器测量醋酸溶液浓度分辨率为0.55%.     

Experimental demonstration and cascadability analysis of a tunable optical buffer based on a re-circulating loop consisting of optical SSB modulator and FBG filter

We demonstrate a tunable optical buffer with variable time delays for label switching applications using an optical single sideband modulator in a fiber Bragg grating-filter loop. This optical buffer realizes payload storage with optional wavelength conversion function, providing flexibility in packet router design. Small sensitivity penalty is observed in our experiment after the payload circulating in the buffer loop three times. The cascadability of the tunable optical buffer is investigated. We provide analysis of the optical signal to noise ratio degradation due to accumulated amplified spontaneous emission noise, and the penalty caused by loss ripple and group delay ripple of the fiber Bragg grating.     

利用双周期光纤光栅实现应变和温度同时测量

提出了一种新颖双周期光纤光栅传感器。在同一段氢载光纤上先后写入长周期光纤光栅、短周期布拉格光纤光栅 ,利用长周期光栅和布拉格光栅对应变和温度敏感性的差异 ,可实现应变和温度的同时测量。实验中采用这种灵敏结构的双周期光栅 ,在 0～ 170 0 με和 2 0℃～ 12 0℃范围内 ,测量精度可达到± 16 με和± 0 8℃。     

一种测定光纤光栅布拉格反射波长位移的简单方法

报道一种简单的光纤光栅对参考法测定光纤光栅布拉格波长的位移的方法，其原理是利用一个布拉格波长可调谐的光纤光栅去跟踪另一个光纤光栅拉格波长的变化，测得的光栅布拉格波长的温度灵敏度为０．００８８ｎｍ／℃，这和用可调谐半导体激光器测得的结果十分接近。     

强度解调型光纤光栅温度传感实验

光纤光栅在工程上应用广泛,但由于存在解调系统复杂、成本高,尤其是需要使用光纤光谱仪等波长解调仪器,使得光纤光栅很难走入本科教学的实验课堂.本文提出了一种基于窄线宽DFB激光器的强度解调方案,极大地简化了光纤光栅传感器的解调系统,完全满足较高分辨率和实时检测的系统要求.合理安排的温度传感实验可以非常直观地展示光纤光栅的线性传感性能,使得工程化的光纤光栅传感技术轻松走进本科教学课堂,具有极高的推广和应用潜力.     

多波长混沌掺铒光纤环形激光器实验研究

利用掺铒光纤环形激光器(EDFRL),基于光纤的非线性克尔效应,实验实现了多波长混沌激光输出。实验研究了EDFRL在时序上通过倍周期进入混沌的路径,并进行了理论分析,理论研究与实验结果一致。实验结果表明,随着抽运功率的增加,其光谱的输出呈现多波长,激光器最多可输出5个不同波长的混沌激光。采用光纤光栅进行滤波后,各个波长的输出均呈现混沌状态。