Characteristics of Fused Optical Fiber Grating Couplers with Tapered Shapes

Fused optical fiber grating couplers (FGCs), in which Bragg gratings are written in the coupling regions of fused optical fiber couplers with tapered shapes along them are theoretically and experimentally investigated. By coupled mode analysis considering these tapered shapes, the drop efficiencies of the FGCs, which are inherently zero for the normal fiber couplers without grating, are calculated. The grating offset, which is the difference between the centers of grating and the coupler taper, is found to be effective to increase the drop efficiency of the FGC. It is determined that the tapered shapes influence the wavelength dependence of the drop efficiency and tolerate the grating offset precision. Apodizations for the grating of FGC are found to be effective in suppressing side lobes of the drop efficiency. Measurement of the wavelength characteristics of drop efficiency and the temperature characteristics of drop wavelength of the fabricated fused FGC confirm that the lightwave with specific wavelength can be dropped by the FGC and that the temperature dependence of the drop wavelength is similar to that of Bragg wavelength changes of usual fiber Bragg gratings.     

光纤Bragg光栅非线性开关动态特性研究

基于光纤Bragg光栅中脉冲演变遵循的非线性耦合模方程,数值分析了光纤Bragg光栅在禁带附近由非线性光学特性导致的Bragg波长偏移。仿真结果表明：随着输入信号功率的增大,光栅的布拉格波长向长波方向移动,反射峰值下降,反射带宽变窄。进一步研究了基于此效应的全光自开关特性,结果表明：此开关的稳定时间短,并且输出脉冲形状保持良好。因此,这种具有高非线性系数的光纤光栅实现的全光开关在全光信号处理方面具有广泛的应用前景。     

Experiments of all-optical switching due to cross-phase modulation in fiber grating coupler by lock-in amp. detection scheme

We report results of experiments examining cross-phase modulation effect on fiber grating coupler (FGC). All-optical switching are observed in both cases of high pump pulses emitted from high-power Nd:YAG laser and mode-locked EDF laser. Based on coherent detection using a lock-in amplifier, the red-shift of the Bragg wavelength for a FGC was estimated to be 0.04-0.06 nm/1.5-1.7 kW peak power of EDF pump light at 1.55 μm. To avoid mixture of pump pulse and signal light at 1.55 μm, we have also performed the experiment using high power Nd:YAG laser as a pump power. For a Nd:YAG laser, the red-shift of Bragg wavelength is estimated to be 0.06 nm at maximum pump power of 2.1 kW. A simple model for the proposed detection scheme is given and the resultant red-shift is analyzed numerically.     

对称结构光纤光栅耦合器及其应用

光纤光栅耦合器(FGC)具有光纤光栅良好的波长选择特性和光纤耦合器的多端口特点，易于实现全光纤的光波分插复用。光纤光栅耦合器主要有4种结构：基于M Z干涉仪的分离型、基于100％耦合器的非对称型、基于0耦合器的非对称型和基于100％耦合器的对称型。着重介绍对称结构光纤光栅耦合器的结构、工作原理和研究现状。提出了测试方案，并探讨了这种器件在大规模波分复用光纤传感器阵列中的应用。     

三种结构的光分插复用器特性比对研究

 针对电交换路由成为全光网通信和密集波分复用等高速信息传递网的电子瓶颈的现状,开展对全光光分插复用器的理论和实验研究。介绍了基于Mach-Zehnder干涉仪和FBG结构、基于FBG和光环行器结构以及一体化光纤光栅耦合器结构的光分插复用器的工作原理,实际构建了3种结构的光分插复用器,并分别搭建测试系统进行了单波长光信号上/下行实验研究,对比了这3种光分插复用器结构的性能和优缺点,为全光光分插复用器的设计制作提供了参考。     

Nonlinear switching in a 20-cm-long fiber Bragg grating

We report experimental observation of nonlinear all-optical switching of a 20-cm-long fiber Bragg grating. The grating is self-switched owing to the optical Kerr effect and in the nonlinear regime shows a 20-dB increase in transmissivity. This increase is a marked improvement from the switching results obtained from shorter gratings.     

高速大容量光纤光栅解调仪的研究

采用半导体光放大器和可调谐法布里-珀罗滤波器,以环路结构组成高速扫描激光器,结合光耦合器、光环路器和光电二极管等,形成4通道大容量高速光纤光栅解调仪。系统采用2kHz的类三角波调制信号,驱动法布里-珀罗滤波器在50nm的光谱范围内进行快速扫描。通过引入光纤梳状滤波器和单峰滤波器组成的参考通路,消除法布里-珀罗滤波器的非线性效应和扫描波长漂移问题,使得解调仪具有很好的稳定性和线性度。高速光纤光栅解调仪的稳定性为2pm,分辨率为1pm,线性度为0.99957,测量精度为5pm,解调频率为2kHz。     

基于光子晶体光纤中脉冲俘获的超高速光开关

提出一种基于光子晶体光纤中脉冲俘获现象的超高速全光开关.信号脉冲处于正常色散区,它们彼此的时域间隔为1 ps.通过数值求解光子晶体光纤中脉冲传播满足的耦合非线性薛定谔方程,发现用孤子脉冲可俘获信号脉冲串中的任何一个脉冲,被俘获的信号脉冲的中心波长明显蓝移,在频域上和其他信号脉冲分离开来,于是让信号脉冲串在输出端通过布喇格光纤光栅,被俘获的信号脉冲将被过滤掉.数值模拟表明,用脉冲俘获实现的光开关响应速率可以达到1 THz.     

磁光光纤Bragg光栅中圆偏振光的非线性传输特性

提出了磁光光纤Bragg光栅的理论模型,给出了圆偏振光在磁光光纤光栅中传播的非线性耦合模方程. 研究表明,在磁光光纤Bragg光栅中,光栅引起正反传播方向的导波光发生耦合,法拉第效应引起磁圆双折射效应,而非线性效应则将左旋和右旋圆偏振光耦合在一起,它们的共同作用可使双稳态状态发生反转、非线性光控光开关阈值功率降低. 与传统光纤光栅相比,利用左旋和右旋磁圆偏振光之间的交叉相位调制实现的脉冲整形具有磁光偏置可调特性,为基于磁光光纤光栅的动态灵活全光3R再生器的研制提供了理论基础. 关键词： 磁光光纤Bragg光栅 圆偏振光 脉冲整形     

光梯度力驱动的纳米硅基光开关

通过一道光改变另一道光的传输路线是光子集成网络中重要而长远的目标, 然而, 由于硅材料的光学非线性较弱, 在硅材料上实现开关的全光控制难以实现. 因此本文提出了一种由光梯度力驱动的纳米硅基光开关, 实现了硅基光开关的全光控制. 该光开关由一个部分悬空的微环谐振器和一个交叉波导结构构成, 当通入一道控制光时, 悬空的微环谐振器在光梯度力的作用下发生弯曲, 微环谐振器的谐振波长随之发生变化, 从而实现光信号的传输路线发生改变. 该光开关利用纳米光子制造技术在标准绝缘体上硅晶圆上制造, 实验数据得出其最小消光比为10.67 dB, 最大串扰为 -11.01 dB, 开关时间分别为180 ns和170 ns. 该光开关具有尺寸小, 响应速度快, 低损耗和可拓展等优点, 在片上集成光路、高速信号处理以及下一代光纤通信网络中具有潜在应用.     

Photonic generation of microwave signal using a dual-wavelength single-longitudinal-mode distributed Bragg reflector fiber laser

In this paper, a novel all-optical microwave generation technique based on a dual-wavelength single-longitudinal-mode (SLM) distributed Bragg reflector (DBR) fiber laser is proposed and demonstrated. By exploiting spatial hole burning (SHB) effect, this laser could provide stable dual-wavelength SLM operation with a wavelength separation of 0.088 nm corresponding to the microwave signal at 10.484 GHz with a 3 dB bandwidth of 28 kHz. By appropriately adjusting the pump power, dual-wavelength oscillation could be maintained at different temperatures. We have theoretically analyzed the mechanism for microwave generation of the proposed DBR laser, and the calculated microwave frequency is in good agreement with our experimental results. Furthermore, experimental observation shows both of the laser wavelengths and generated microwave signals have good stability at room temperature.     

Design of an insensitive-polarization all-optical switch based on multimode interference structures

This paper presents a new design for an insensitive-polarization all-optical switch using 2 × 2 multimode interference (MMI) couplers. The switching structure can operate at central operating wavelength 1550 nm for both polarizations. A nonlinear directional coupler is used to realize the phase shifter and therefore switching mechanism is obtained. The transfer matrix method and beam propagation method are used to design and optimize the whole device structure.     

Optimized grating-frustrated coupler

A complete theoretical analysis of a modified grating-frustrated coupler with a second grating in the input channel is presented. We show that this second grating allows for a reduction to zero of backreflected light and transmits all the radiation near the Bragg wavelength to a drop port.     

硅基二维光子晶体耦合器理论研究

光子晶体是一种具有光子带隙的新型人工材料,利用其具有控制和限制光子运动的特性可以制成新颖的光学器件。利用硅基二维光子晶体,提出了一种4端口耦合器。采用时域有限差分法作为研究工具,TM模作为研究对象,从理论上分析了这种器件的特性。在不同的耦合长度下研究光在输出端的功率透射率。结果表明选择适当的耦合长度可以使光在器件中呈现不同的状态。进一步研究表明,通过改变器件内部介质柱的半径,可以改变光在输出端的输出功率。从而证实了这种器件不仅具有波长选择性,而且具有潜在的可调节性,这些特性使得这种器件在全光开关的应用上具有潜在的优势。     

包含掺铒光纤和微结构光纤的光纤环镜光开关

设计了一种低开关功率的全光开关.将掺铒光纤和微结构光纤引入Sagnac环镜中,信号光在泵浦光作用下经过掺铒光纤被放大,破坏了环镜的平衡,利用交叉相位调制效应使两束反向传输的信号光产生非线性相移,实现了光开关效应.理论分析表明:信号光经过掺铒光纤后,增益越大微结构光纤的非线性系数越高,开关功率越低,并且环镜信号光的透射率随两束反向传输信号光的相移差成余弦变化.仿真得到开关功率约为26.73 mW,与理论分析一致.     

Fully reconfigurable optical add-drop multiplexer based on parallel configuration using Mach-Zehnder module

Reconfigurable optical add-drop multiplexer (ROADM) with the ability of dynamic configuration will be one of the core equipment for the future optical transport networks. This paper proposes an effective scheme for fully ROADM with parallel modularized structure and ability of upgrading. Each module consists of a Mach-Zehnder interferometer based on fiber Bragg grating (FBG), a 1 × 2 optical switch and a Y-model combiner. Optical signal with single wavelength or multiwavelength could be dropped or added at one drop port or add port by configuring the optical switch in each module. The proposed ROADM with four-stage parallel connection is designed and experimentally investigated to prove its performance and advantage in dynamic selection of the wavelengths and upgrading. It is also showed that this ROADM can also reduce the ununiformity of power at output port and drop port to improve the optical signal to noise ration (OSNR) of the whole system.     

Plasmonic all-optical bistable device based on nematic liquid crystal

Low-power all-optical bistable liquid crystal (LC) devices are reported in which surface plasmons propagate along a metallic grating. The threshold switching illumination was 1.4 mW/mm² in the device with the twisted-nematic LC cell. This is a lower value than for all-optical bistable devices reported previously. This low-power bistability device can be used in two-dimensional optical memories or spatial light modulators.     

Quasi-distributed displacement sensor for structural monitoring using a commercial OTDR

A quasi-distributed displacement sensor for structural monitoring using an optical time domain reflectometer is demonstrated. Four displacement sensing heads are placed along a standard single mode optical fibre in several locations with different intervals. Their configurations introduce power loss through the decrease of their fibre loop radius when displacement is applied. The decrease of the light intensity with displacement variation is reported. Losses of 9 dB for a 120 mm displacement with a sensitivity of 0.027 dB/mm are reported. The quasi-distributed configuration is able to address sensors with 1 m distance resolution between them.     

A multi-parameter optical fiber sensor with interrogation and discrimination capabilities

A multi-parameter and multi-function, but low-cost, optical fiber grating sensor with self-interrogation and self-discrimination capabilities is presented theoretically and experimentally. The sensor bases on three fiber Bragg gratings (FBG) and one fiber long period grating (LPG). Strain, vibration, pressure, ordinary temperature (−10 to 100 °C) and high temperature (100–800 °C) can be measured by the sensor. When high temperature (100–800 °C) is measured, the LPG is used as a high temperture sensor head and FBG₁ is used as an interrogation element. Alternatively, when one of the other four measurands is measured, FBG₁ (or FBG₂) is used as a sensor head and LPG is used as an interrogation element. When two of the other four measurands are measured simultaneously, FBG₁ and FBG₂ are used as sensor heads and LPG is used as a shared interrogation element. FBG₃ is used as a reference element to eliminate the errors resulted from light source fluctuation and the cross-sensitivity between measurand and environmental temperature. The measurands can be interrogated according to the signals of the photodiodes (PDs), which are related to the relative wavelength shift of the LPG and the FBGs. Experimental results agree well with theoretical analyses. The interrogation scheme is immune to light source fluctuation and the cross-sensitivity between measurands and enviromental temperature, and also the dynamic range is large.     

基于色散补偿光纤的高速光纤光栅解调方法

本文提出并论证了一种光纤光栅高速解调的新方法, 利用色散补偿光纤的色散效应, 将光纤光栅的波长漂移信息转换成时域信息. 采用脉冲激光器作为光源, 仅需一个光脉冲可获取单根光纤上所有光纤光栅的反射光脉冲, 再根据各个光栅反射回光脉冲的延时变化即可实现波长的解调. 本方法可用于准分布光纤光栅传感网络解调, 系统采用全光纤结构, 无需波长扫描, 大大提高了解调速度. 本文搭建了测试系统进行实验验证, 对3个光纤光栅组成的准分布式传感网络进行了解调, 实验结果表明, 解调出的光纤光栅布喇格波长线性度好, 解调速度最高可达1 MHz, 采样数据取10次平均后解调线性度可达0.9969, 解调误差约为27.8 pm.