反应溅射法制备TiO2薄膜

报道了用反应溅射法制备TiO₂薄膜的实验研究.详细研究了氧分压、基底温度和退火温度对成膜结构的影响.制备出了具有金红石和锐钛矿晶体结构的TiO₂薄膜.分析了金红石和锐钛矿晶体的形成条件,并对薄膜的表面形貌进行了测量. 关键词： 反应溅射 2薄膜')" href="#">TiO₂薄膜     

Sn掺杂的纳米TiO_2的拉曼散射

本文主要利用拉曼光谱研究一组在合成过程中掺入了不同浓度锡的纳米二氧化钛样品,确定其从锐钛矿结构到金红石型结构的转变,进而分析其金红石型结构的形成。拉曼光谱测试表明,晶型导向剂SnO2的引入促使金红石型TiO2在较低的反应温度下形成,高温合成条件的免除使我们获得了很好的纳米级的金红石型TiO2晶体。此晶体具有有趣的包覆型结构,金红石型TiO2纳米晶体内包含着同结构的SnO2籽晶。分析其成因,在结晶过程中,掺入的杂质原子Sn4+与O2-结合,先沉积出金红石型结构的SnO2作籽晶,金红石型结构的SnO2和同样结构的TiO2晶格常数十分接近,促使了TiO2在它表面外延生长,形成金红石结构的包覆纳米晶。     

低温拉曼光谱研究二氧化钛纳米晶的相变

本文通过对二氧化钛纳米晶在-190℃温度的低温拉曼光谱的研究,得到了在二氧化钛纳米晶聚集体中,可以发生锐钛矿到板钛矿然后到金红石和/或直接到金红石的相变;也可发生板钛矿到锐钛矿然后到金红石和/或直接到金红石的相变。     

滤纸模板法二氧化钛纸的制备及其光催化活性

以滤纸为模板成功制备了由微带组成的二氧化钛纸光催化材料,利用红外光谱、热重量分析、X射线衍射、扫描电子显微镜对其进行了表征. 通过对甲基橙溶液在紫外光下的降解,考察了制得样品的光催化性能. 结果表明：锐钛矿/金红石比为10:1的二氧化钛纸具有最高的催化活性,且滤纸纤维提高样品的结晶度和锐钛矿的相转化温度. 并讨论了对二氧化钛纸的形成机理.     

直接热氧化制备氧化然薄膜电极的研究——Ⅰ.制备、结构和电化学性质

采用原子力显微镜、X光衍射仪、电化学阻抗谱等手段对热氧化制备氧化钛膜的结构和电化学性质进行了研究。结果表明,金属钛直接热氧化制备的薄膜为金红石型二氧化钛薄膜;随氧化温度升高和时间延长,薄膜结晶度逐渐增大;随氧化温度升高;二氧化钛平带电位向负方向移动;当温度大于600℃后,二氧化钛结晶致密,电子导电性减小。     

TiO_2晶型及其相变的高温拉曼光谱研究

本文测量了锐钛矿型和金红石型TiO2常温至1923K的高温拉曼光谱,观察了锐钛矿型TiO2在1373K～1473K间发生相变,不可逆转化为金红石型TiO2,分析了特征峰随温度变化的规律以及两种结构相的温度依赖性。并为不同晶型TiO2的研究、生产和应用提供重要的实验依据。     

直接热氧化制备氧化钛薄膜电极的研究Ⅰ. 制备、结构和电化学性质

采用原子力显微镜、 X光衍射仪、电化学阻抗谱等手段对热氧化制备氧化钛膜的结构和电化学性质进行了研究.结果表明,金属钛直接热氧化制备的薄膜为金红石型二氧化钛薄膜;随氧化温度升高和时间延长,薄膜结晶度逐渐增大;随氧化温度升高,二氧化钛平带电位向负方向移动;当温度大于600℃后,二氧化钛结晶致密,电子导电性减小.     

纳米金红石TiO2光催化剂的水解合成及其性能

采用水解法在323 K制备了比表面积较大的纳米金红石TiO₂光催化剂,并通过X射线衍射（XRD）、BET比表面积测试法、紫外-可见吸收光谱（UV-Vis）、红外光谱（IR）和光电化学（PEC）测量对纳米光催化剂进行了表征。以甲基橙为光催化反应的模型化合物,在比表面积相近的条件下,对纳米金红石和锐钛矿TiO₂光催化剂的光催化活性进行了评价。光催化实验结果表明：比表面积为～95 m2·g-1时,比表面积相近的金红石和锐钛矿的紫外光催化活性相当, 但金红石的可见光催化活性明显高于锐钛矿的可见光催化活性。光电化学实验表明: 在紫外光照射下催化剂的光电流密度从弱到强的顺序与其紫外光催化活性从低到高的次序一致。     

热处理对爆轰合成的纳米TiO_2混晶的结构相变的影响

采用爆轰法制备了纳米TiO2混晶体,初步研究了不同煅烧温度(600℃和720℃)和不同煅烧时间(1 h,2 h,3.5 h和5 h)对其微结构和结构相变行为的影响,并应用热动力学理论讨论了从锐钛矿相到金红石相的结构相变过程和相变机理.研究表明:随着煅烧温度的升高和煅烧时间的增加,纳米TiO2的粒径逐渐增大,混晶中金红石相的含量逐渐提高.与常规方法制备的纳米TiO2不同的是,在相同煅烧温度和煅烧时间下金红石相的平均生长速率明显低于锐钛矿相.锐钛矿相完全相变为金红石的温度也明显低于常规方法报道的相变温度.该研究会对控制纳米TiO2晶体尺寸和批量合成提供一定的理论和实验指导.     

Zr掺杂TiO_2薄膜的光学性能和光催化性能

为了研究TiO2禁带宽度和光吸收系数对其光催化性能的影响,利用电子束沉积方法在玻璃基底上制备了TiO2薄膜及Zr掺杂TiO2薄膜。采用拉曼光谱仪和分光光度计对膜的结构和吸收光谱进行了表征。研究结果表明:当退火温度为773K时,沉积得到的TiO2薄膜为锐钛矿结构薄膜;掺杂使TiO2禁带宽度变窄,吸收波长红移,在350~450nm附近光吸收系数增大,增强了TiO2的光催化活性。     

Investigation on the transition crystal of ordinary rutile TiO2 powder by microwave irradiation in hydrogen peroxide solution and its sonocatalytic activity

The transition crystal TiO(2) catalyst with high sonocatalytic activity was obtained utilizing the microwave irradiation in hydrogen peroxide solution. At the same time a series of affecting factors (microwave irradiation time, heat-treated time and heat-treated temperature) to prepare the TiO(2) catalyst on the sonocatalytic degradation of parathion were considered in this paper. The ultrasound of low power was used as an irradiation source to induce treated TiO(2) particles to perform catalytic activity. The results show that the sonocatalytic activity of the transition crystal TiO(2) powder is obviously higher than those of pure ordinary rutile and anatase TiO(2) powders. At last, the parathion in aqueous solution was degraded completely and became some simple inorganic ions such as NO(3)(-), PO(4)(3-), SO(4)(2-), etc. The degradation ratio of parathion in the presence of the transition crystal TiO(2) catalyst attains nearly 80% within 60 min ultrasonic irradiation, while corresponding ones are only 65.23% and 53.88%, respectively, for pure ordinary rutile and anatase TiO(2) powders.     

铂颗粒粒径效应:负载铂纳米颗粒的TiO2薄膜性质研究

制备了负载不同大小Pt纳米颗粒的TiO薄膜。利用TEM测定了Pt粒子的大小,XRD,UV—Vis和测量光电流等方法对TiO2复合膜进行了表征,以亚甲基蓝降解反应评价了Pt／TiO2薄膜的光催化活性。结果表明,在负载相同物质的量的Pt情况下,Pt颗粒的大小直接影响TiO2薄膜的性能,显示较强的粒径效应,当负载平均粒径约5nm的Pt粒子后,薄膜具有最高的光电流和光催化活性。     

Investigation on the sonocatalytic degradation of acid red B in the presence of nanometer TiO2 catalysts and comparison of catalytic activities of anatase and rutile TiO2 powders

Here, the nanometer anatase and rutile titanium dioxide (TiO(2)) powders were introduced to act as the sonocatalysts during the ultrasonic degradation of azo dye-acid red B which was chosen as model compound. The ultrasound of low power was used as an irradiation source to induce TiO(2) particles performing catalytic activity. It was found that the processes of sonocatalytic degradation were different between nanometer anatase TiO(2) and nanometer rutile TiO(2). For nanometer anatase TiO(2) catalyst, the acid red B was mainly oxidated by the holes on the surface of nanometer anatase TiO(2) particles, so that the decolorization and degradation happened at the same time. For the nanometer rutile TiO(2) catalyst, the acid red B was mainly oxidated by the *OH radicals from the ultrasonic cavitation, so that the decolorization of azo bond takes place primarily, and then the degradation of naphthyl ring does. The intermediates of acid red B in the presence of nanometer anatase and rutile TiO(2) powders have been monitored by UV-vis spectra and high performance liquid chromatography (HPLC), respectively. All experiments indicated that the degradation effect of acid red B in the presence of nanometer anatase TiO(2) powder was obviously better than that in the presence of nanometer rutile TiO(2) powder. Hence, the method of sonocatalytic degradation for organic pollutants in the presence of nanometer anatase TiO(2) powder is expected to be promising as an advisable choice for the treatment of organic wastewaters in future.     

TiO2光催化剂的光谱研究

采用sol-gel法制备了纳米TiO2光催化剂,运用FTIR,FT－Ranam,DSR等光谱技术对催化剂进行了表征,以光催化解油酸作为模型反应考察光催化活性。实验结果表明,催化剂的烧结温度对催化剂的晶相结构、半导体能带结构、光吸收性能及光催化活性均产生显著的影响,当烧结温度为400℃时,TiO2光催化剂具有最好的表观吸光度,最大的吸收带边,以及最佳的光催化活性。     

The importance of the majority carrier polarity and p-n junction in titanium dioxide films to their photoactivity and photocatalytic properties

In this paper, undoped polycrystalline titanium dioxide films have been deposited by atomic layer deposition (ALD) using the titanium tetrachloride–water process. These films have been anatase, rutile, or mainly anatase with a varying content of rutile depending on the deposition conditions. The polarity of the majority carriers on the films has been measured with the hot-probe test and, over the range of deposition temperatures used, the anatase or anatase-dominant films have been found to be p-type whereas the rutile films have been n-type. X-ray diffraction (XRD), contact angle measurements, and methylene blue degradation tests were performed to investigate the crystallinity, photoactivity, and photocatalytic properties. All the p-type films showed good photoactivity as determined by their water contact angle while the best photocatalytic activity was shown with anatase films containing a small proportion of rutile. An explanation for the superior photoactivity of anatase due to its p-type polarity is given and the high photocatalytic property for anatase-dominant films is ascribed to the existence of p-n junctions leading to carrier separation.     

Photocatalytic activity of dc magnetron sputter deposited amorphous TiO2 thin films

For photocatalytic thin film applications TiO₂ is one of the most important materials. The most studied TiO₂ crystal phase is anatase, though also rutile and brookite show good photoactivity. Usually anatase or a mixture of rutile and anatase is applied for powder or thin film catalysts. It has been claimed that amorphous films do not exhibit any or only a very low photocatalytic activity.We have deposited amorphous thin films by dc magnetron sputtering from sub-stoichiometric TiO_2−x targets. The coatings are transparent and show a photocatalytic activity half of that of a thin layer of spin-coated reference photocatalyst powder. Annealing the thin films to yield anatase crystallization more than doubles their photocatalytic activity. At the same film thickness these thin films show the same activity as a commercially available photocatalytic coating.The dependence of the photocatalytic activity on deposition parameters like gas pressure and sputter power is discussed. A decrease in film density, as deduced from the refractive index and the microstructure, resulted in an increase in photocatalytic activity. Film thickness has a marked influence on the photocatalytic activity, showing a strong increase up to 300-400 nm, followed by a much shallower slope.     

介孔二氧化钛光催化降解乙醛及其影响因素

"应用溶剂蒸发自组装的方法合成了具有蠕虫状孔道的介孔二氧化钛粉末和薄膜．考察了不同焙烧温度对材料介孔结构和光催化性能的影响．乙醛光催化降解实验用来表征不同焙烧温度下介孔材料的光催化性能．结果表明实验中合成的介孔二氧化钛材料的光催化活性明显高于颗粒二氧化钛(Degussa P25)．其中400 oC焙烧的样品具有平均孔径为6.0 nm的窄的孔径分布和117 m2/g的大的比表面积．通过对光催化活性结果的分析,发现介孔二氧化钛的活性主要受其比表面积和结晶性的共同影响．对介孔二氧化钛薄膜材料进行了同样的光催化表     

Pr掺杂TiO2光催化剂的制备及其对酸性品红降解反应的催化性能

以钛酸四丁酯为前躯物,采用溶胶-凝胶法制备了掺杂不同含量Pr的TiO2光催化剂,利用XRD,TG-DTA,AFM,UV-Vis,FTIR等手段对催化剂进行了表征。并通过酸性品红光催化降解实验对其光催化性能进行了评价,考查了实验条件,如催化剂用量,烧结温度,掺杂量等对催化剂催化活性的影响。Pr2O3的掺杂阻碍了TiO2晶相由锐钛矿型向金红石型的转变,使TiO2的粒径减小,比表面积增大,催化活性增强。当Pr掺杂量为0.8%,催化剂用量为0.03g,烧结温度为500℃时,酸性品红的降解率达到97%以上,酸性品红的降解反应为准一级反应。     

TiO2柱撑蒙脱土的制备及其对品红降解的催化反应

基于TiO2光催化剂的优良光催化活性,采用酸性溶胶法合成了TiO2柱撑蒙脱土复合光催化剂,利用IR,UV-Vis,TG/DTA,XRD及SEM等手段对复合催化剂进行了表征,通过太阳光对酸性品红光催化降解实验,考察了催化剂的光催化活性。该催化剂比纳米TiO2对酸性品红的光催化降解反应表现出更高的催化活性,而且更易于沉降、回收。当TiO2柱撑蒙脱土光催化剂的用量为0.2 g.(100 mL)-1,酸性品红溶液的pH值为3时,在太阳光下40 min内酸性品红基本降解完全,而且该降解过程符合Langmuir-Hin-shelwood方程。X射线衍射(XRD)分析表明钛柱撑蒙脱土的层间距较钠基蒙脱土有明显的增大,紫外-可见吸收光谱表明TiO2柱撑蒙脱土比纳米TiO2具有更高的光吸收效率。     

Ag-TiO2和Au-TiO2复合薄膜光催化降解偶氮染料酸性大红GR的研究

以玻璃珠为载体,溶胶-凝胶法制Ag-TiO2和Au-TiO2复合薄膜,研究了水溶液中的偶氮染料酸性大红GR进行了固定相光催化氧化以及银和金的掺杂量、染料水溶液的pH值、光源、催化剂的重复使用性等因素的影响.负载型复合光催化剂Ag-TiO2和Au-TiO2的光催化活性显著提高.当Ag和Au掺杂TiO2的质量分数分别为0.4%和0.6%时,最高光解率分别提高了2.1倍和1.8倍.