修饰阴极界面提高聚合物白光二极管发光效率

利用聚合物的不同溶解性,研究用旋涂方法制备双层高分子白光二极管(WPLED),采用器件结构为：ITO/PEDOT(50nm)/PVK:PFO-BT: PFO-DBT(40nm)/PFO(40nm)/Ba(4nm) /Al(120nm),当相对比例为PVK: PFO-BT:PFO-DBT=1∶4%：3%时,得到标准白光,最大电流效率为2.4 cd/A,最大亮度为3215 cd/m²,色坐标为(0.33,0.34).用水溶性的聚电介质层修饰阴极界面,器件效率可以进一步提高到5.28 cd 关键词： 聚合物发光二极管 白光 双发光层结构     

基于量子阱结构的混合型白光有机发光器件

以荧光材料BePP2结合量子阱作为蓝光发射层,磷光材料GIrl和R-4B掺入到混合双极性主体材料CBP∶Bphen中分别作为绿、红发光层并且在红绿发光层中引入间隔层TPBI,组合得到发白光的混合型有机发光器件。其中量子阱是以BePP2作为势阱、TCTA为势垒。结果表明:当势垒层数为2时,器件的最大发光亮度和电流效率分别为21 682.5 cd/m2和23.73 cd/A;当电压从7 V增加到14 V时,色坐标从(0.345,0.350)变化到(0.340,0.342)。与无量子阱结构的参考器件相比,势垒层数为2的器件的最大功率效率为8.07 lm/W,色坐标变化相对最小为±(0.005,0.008),还有一个高的显色指数83。     

TCTA对红绿磷光有机电致发光器件发光层激子的调控作用

制备了结构为ITO/MoO3(50 nm)/NPB(40 nm)/TCTA(10 nm)/CBP:14%GIr1(30 nm)/TCTA(x)/CBP:2%R-4B(10 nm)/BCP(10 nm)/Alq3(40 nm)/LiF(1 nm)/Al(100 nm)的红绿磷光有机电致发光器件,GIr1和R-4B分别为红、绿磷光染料。通过在红绿间插入较薄间隔层TCTA的方法,调节载流子、激子在红绿发光层中的分布,并结合TCTA和BCP对发光层内载流子和激子的有效阻挡作用,研究了载流子调控层TCTA在不同厚度下对器件发光性能的影响。结果表明,TCTA为1 nm时,器件的发光性能得到了很好的提升。电压为6 V时,TCTA为1 nm器件的电流密度、亮度、最大电流效率分别为0.509 mA/cm2、69.91 cd/m2和13.72 cd/A,而TCTA为0 nm器件的电流密度、亮度、最大电流效率分别为1.848 mA/cm2、215.7 cd/m2和11.67 cd/A。     

非掺杂型高效绿色磷光有机电致发光器件

在空穴传输层TCTA与电子传输层TPBi之间引入磷光染料Ir(ppy)3超薄发光层,制备了结构为ITO/MoO_3(2 nm)/NPB(40 nm)/TCTA(10 nm)/Ir(ppy)3(xnm)/TPBi(40 nm)/LiF(1 nm)/Al(80 nm)的非掺杂磷光有机电致发光器件。通过调控非掺杂发光层的厚度,详细研究了Ir(ppy)3层厚度对器件性能的影响。实验结果表明,当非掺杂发光层厚度为0.2 nm时,器件的性能最好,器件的亮度、效率和外量子效率分别达到26 350 cd·m~(-2)、42.9 cd·A~(-1)和12.9%。研究结果表明,采用超薄的非掺杂发光层可以简化器件结构和制备工艺,获得高效率的OLED器件。     

基于超薄发光层及双极性混合间隔层的白光有机发光器件研究

本文采用非掺杂超薄发光层及双极性混合间隔层结构,获得了高效、光谱稳定的白光有机发光器件.基于单载流子器件及单色蓝光有机发光器件的研究,确定了双极性混合间隔层的最佳比例;通过瞬态光致发光寿命研究,验证了不同发光材料之间的能量传递过程;得到的三波段和四波段白光有机发光器件的最高效率分别为52 cd/A (53.5 lm/W)和13.8 cd/A (13.6 lm/W),最高外量子效率分别为17.1%和11.2%.由于发光层不同颜色之间依次的能量传递结构,三波段白光有机发光器件的亮度从465到15950 cd/m~2时,色度坐标的变化?CIE仅为(0.005, 0.001);四波段白光有机发光器件的亮度从5077到14390 cd/m~2时,色度坐标的变化?CIE为(0.023, 0.012).     

间隔层对双发光层白色有机电致发光器件性能的影响

采用蓝色bis (FIrpic)和黄色bis iridium(acetylacetonate) 两种磷光染料,制备了双发光层结构的白色有机电致发光器件,器件结构为ITO/TAPC (30 nm)/host: (t-bt)₂Ir(acac) /spacer (x nm)/host: FIrpic (15 nm, 8%)/Bphen (40 nm)/Mg∶Ag (200 nm)。分别选用p型1,1-bis cyclohexane (TAPC)和n型tris borane (3TPYMB)作为主体材料制备了两种类型的器件,通过在两个发光层之间加入一层较薄的间隔层进行器件优化。结果表明,加入间隔层之后,器件性能得到提高,获得了色稳定性较好的白光器件。当主体为TAPC时,使用间隔层后器件取得最大亮度为19 550 cd/m²,最大电流效率为8.3 cd/A;当主体为3TPYMB时,使用间隔层后器件的最大亮度为1 950 cd/m²,最大电流效率为30.7 cd/A。实验结果表明,器件性能的提高,是由于加入了间隔层之后载流子复合区域拓宽,促进了发光层中电子和空穴的平衡。     

BPhen作为发光层间隔层对黄光OLED的影响

使用R-4B和GIrl作为磷光掺杂剂、CBP为主体、BPhen为发光层间隔层,制备了包含红、绿双发光层的黄色磷光OLED器件。器件结构为ITO/Mo O3(40 nm)/NPB(40 nm)/TCTA(10 nm)/CBP∶GIrl(14%)(20nm)/BPhen(x nm)/CBP∶R-4B(6%)(10 nm)/BCP(10 nm)/Alq3(40 nm)/Li F(1 nm)/Al(1 000 nm)。BPhen位于两发光层之间,具有调节载流子复合的功能,其中x为BPhen的厚度。通过调整x的值,研究了BPhen厚度对OLED器件发光性能的影响。实验结果表明,适当厚度的BPhen层可以提高器件的发光亮度和电流效率。BPhen厚度为6 nm的器件性能最佳,16 V驱动电压下的器件亮度最高可达11 270 cd/m2,最大电流效率为24.35 cd/A,而且绿光和红光波峰强度相近,黄光颜色纯正,色坐标趋近于(0.5,0.5)。     

基于颜色转换层的有机白光器件性能研究

以DCJTB为颜色转换层,结合双蓝色发光层有机电致发光器件制备了结构为PMMA∶DCJTB(x%)/ITO/NPB(30nm)/mCP(5nm)/mCP∶Firpic(8%,30nm)/TPBi∶Firpic(8%,10nm)/TmPyPB(30nm)/Cs2CO3(1nm)/Al(x=0.7,1.0,1.5)的白色有机发光器件.结果表明,器件的效率和显示性可通过DCJTB浓度加以调控,当DCJTB浓度为1.0%时,器件拥有最佳性能,其最大电流效率、色坐标和显色指数分别为13.4cd·A-1、(0.33,0.31)和69.为进一步提高器件效率和显色性,在发光层TPBi∶Firpic与电子传输层TmPyPB之间插入TPBi/TPBi∶Ir(ppy)3结构,研究表明:该插入结构能丰富器件发光颜色,增大颜色转换层的有效吸收光量;同时可限制激子复合区域,提升激子利用率,实现了器件效率和显色性能的同时提升.获得的白光器件最大电流效率和显色指数分别为17.8cd·A-1和81,分别提升了33%和17%,色坐标仅漂移(0.02,0.02).     

TCTA在外电场下的双分子发光现象

制备了三苯胺化合物4,4′,4″-三(咔唑-9-基)三苯胺(TCTA)的单层器件ITO/MoO_3/TCTA/LiF/Al和TCTA/TPBi双层异质结器件ITO/NPB/TCTA/TPBi/Bphen/LiF/Al,研究了TCTA的双分子发光现象。通过测试器件的光电性能和薄膜的稳态光谱,得出以下结论:(1)单层器件的电致发光光谱有425 nm和600 nm两个发光峰。与TCTA薄膜的光致发光光谱对比,可知425 nm附近的蓝色发光峰来源于TCTA单体发光,而600 nm附近的橙色发光应为TCTA二聚体electromer的发光。蓝色和橙色发光混合,使单层器件发光颜色表现为白色,对应色坐标为(0.381,0.343)。(2)TCTA/TPBi双层异质结器件的电致发光光谱为440 nm的单峰,器件的最大发光亮度为930 cd/m~2,发光性能明显优于单层器件。结合薄膜TCTA、TPBi和TCTA/TPBi的光致发光光谱和紫外-可见光吸收光谱,可知双层器件的发光来自TCTA~+TPBi~-电致激基复合物。双层器件表现出良好的色稳定性,电压在6～11 V范围,CIE色坐标为(0.18±0.01,0.14±0.01)。     

新型高色纯度弱电流猝灭性蓝色有机发光器件

以ADN为基质,分别以不同掺杂剂制备了四种蓝色有机发光器件,器件结构为:CuPc(12 nm)/NPB(40 nm)/AND∶Dopant(50 nm)/Alq(12 nm)/LiF(4 nm)/Al。掺杂剂有:BCzVB(amino-substituted distyrylarylenederivatives)、TBPe、BCzVBi和DSA-ph四种。研究了最佳掺杂浓度以及器件的亮度、电流密度、效率和色坐标等电学特性和光学特性。其中掺杂BCzVB制备了色纯度高、低电流猝灭性的蓝色有机发光器件,色坐标达到x=0.146,y=0.162,最大亮度为11600 cd/m2(15 V),电流效率为2.8 cd/A,流明效率为1.79 lm/W;以ADN为基质,分别以TBPe、BCzVBi和DSA-ph为掺杂剂,制备了另外三种对比器件。器件ADN∶TBPe色坐标为x=0.162,y=0.222(蓝绿光),效率随电流的增加而降低很快;器件ADN∶BczVBi有较好的色纯度(色坐标:x=0.164,y=0.146),但电流效率较低:2.03 cd/A,效率随电流的增加降低幅度也较快。器件ADN∶DSA-ph效率较高为8 cd/A,效率随电流增加变化幅度不大,但色纯度比较差(x=0.153,y=0.306),适合于做白色有机发光器件。     

Random lasing in an organic light‐emitting crystal and its interplay with vertical cavity feedback

The simultaneous vertical‐cavity and random lasing emission properties of a blue‐emitting molecular crystal are investigated. The 1,1,4,4‐tetraphenyl‐1,3‐butadiene samples, grown by physical vapour transport, feature room‐temperature stimulated emission peaked at about 430 nm. Fabry‐Pérot and random resonances are primed by the interfaces of the crystal with external media and by defect scatterers, respectively. The analysis of the resulting lasing spectra evidences the existence of narrow peaks due to both the built‐in vertical Fabry‐Pérot cavity and random lasing in a novel, surface‐emitting configuration and threshold around 500 μJ cm⁻². The anti‐correlation between different modes is also highlighted, due to competition for gain. Molecular crystals with optical gain candidate as promising photonic media inherently supporting multiple lasing mechanisms.     

有机激光材料及器件的研究现状与展望

有机激光器因其制备简单, 价格低廉和易于集成等优势, 一直以来备受科研工作者的关注. 与无机激光介质相比, 有机激光材料来源广泛, 并具有发射光谱宽, 吸收与发射截面积大等特性, 因而有很大的发展潜力. 本文从激光的基本原理出发, 对有机激光材料的种类、特性进行了归纳, 并总结了高效有机激光材料的普遍特征; 分类讨论了常见有机激光微腔的类型与特点, 对有机激光系统内增益与损耗之间的动态关系进行了探讨. 鉴于实现电抽运激光一直以来都是有机激光领域期待解决的难题, 本文重点讨论了当前电抽运有机激光的研究现状和发展瓶颈, 以及科研工作者们对此问题的不懈探索和已有的工作基础. 最后总结了光抽运有机激光近年来的总体进展, 未来的研究方向, 这对于读者拓展新的研究思路有很好的参考和借鉴意义.     

Organic quantum well and superlattice characteristics in quasi-one-dimensional multiblock copolymers

A tight-binding calculation was presented to describe multiblock copolymers, such as [...-(PA)x-(PPP)y-...] composed of PA (polyacetylene) and PPP (poly(p-phenylene). It is found that a copolymer has a quantum well and superlattice characteristics, and evident is the effect of the composite lengths, the interfacial couplings and the electron-phonon interactions on the electronic properties of a copolymer. The quantum tunneling, the Franz-Keldysh effect and the quantum confinement can be generated under an applied electric field. These results were compared to those of traditional inorganic quantum well and superlattice systems.     

The basis of organic spintronics：Fabrication of organic spin valves

Organic spintronics focuses on utilizing the spin degree of freedom in organic materials because of the long spin relaxation time. The vertical organic spin valve (OSV) is a typical sample structure used to study the spin transport phenomena. However, the fabrication of high quality OSVs is difficult, which results in controversial experiment results and hence hinders the development of organic spintronics. In this work, we describe our recent study on the fabrication of typical vertical organic spin valves, La_0.67Sr_0.33MnO₃ (LSMO)/Alq₃/Co. The LSMO bottom electrodes are annealed to obtain an atomically smooth surface and improved magnetic properties. The top Co electrodes are deposited by an indirect deposition method to reduce the interfusion between Co and Alq3. The controlled fabrication process provides much better performance and sample yield of OSVs.     

Length dependence of rectification in organic co-oligomer spin rectifiers

The rectification ratio of organic magnetic co-oligomer diodes is investigated theoretically by changing the molecular length. The results reveal two distinct length dependences of the rectification ratio: for a short molecular diode, the chargecurrent rectification changes little with the increase of molecular length, while the spin-current rectification is weakened sharply by the length; for a long molecular diode, both the charge-current and spin-current rectification ratios increase quickly with the length. The two kinds of dependence switch at a specific length accompanied with an inversion of the rectifying direction. The molecular ortibals and spin-resolved transmission analysis indicate that the dominant mechanism of rectification suffers a change at this specific length, that is, from asymmetric shift of molecular eigenlevels to asymmetric spatial localization of wave functions upon the reversal of bias. This work demonstrates a feasible way to control the rectification in organic co-oligomer spin diodes by adjusting the molecular length.     

Organic single crystal phototransistors: Recent approaches and achievements

Organic phototransistors (OPTs), compared to traditional inorganic counterparts, have attracted a great deal of interest because of their inherent flexibility, light-weight, easy and low-cost fabrication, and are considered as potential candidates for next-generation wearable electronics. Currently, significant advances have been made in OPTs with the development of new organic semiconductors and optimization of device fabrication protocols. Among various types of OPTs, small molecule organic single crystal phototransistors (OSCPTs) standout because of their exciting features, such as long exciton diffusion length and high charge carrier mobility relative to organic thinfilm phototransistors. In this review, a brief introduction to device architectures, working mechanisms and figure of merits for OPTs is presented. We then overview recent approaches employed and achievements made for the development of OSCPTs. Finally, we spotlight potential future directions to tackle the existing challenges in this field and accelerate the advancement of OSCPTs towards practical applications.     

Interfacial processes in small molecule organic solar cells

This paper presents an overview of the recent progress of small molecule organic solar cells mainly based on the previous worksof our group. We will mainly focus on the interfacial processes in the cells. The dissociation of excitons at electrode/organic andorganic/organic interfaces can be directly observed by transient photovoltage measurements. A simple model including dissociationof excitons at the interface and drift of free carriers in the built-in field is proposed to explain the observed signals of ...     

可降解有机物湿解实验研究

选用杂草作为城市生活垃圾中可降解有机物的典型组分,研究了湿解参数对湿解后固体、气体和液体比例的影响,以及固体成分中有机质、黄腐酸、胡敏酸和大量营养元素的影响。结果表明,湿解应采用适当的高温和短的反应时间,如在 480 K 下湿解 0.25 h,固体成分保留最多,有机质含量最丰富,腐殖化程度最高,但大量营养元素的含量也最低。     

吩基吡啶铍(Bepp2)配合物的高效蓝光器件

高荧光的吩基吡啶铍(Bepp2)作为发射层构成高效蓝色电致发光器件.这一由空穴注入层、空穴传输层、Bepp2发射层组成的多层器件,使用一电子传输层以获得高性能.这种器件结构,最大亮度达6 200cd·m-2、电致发光效率1.3 cd/A(0.71 lm/W),吩基吡啶铍(Bepp2)的电致发光光谱峰值在451 nm.这些初步的结果表明配合物铍应用于电致发光是非常有前景的材料.在化学方面的进一步考察和新的羟苯基吡啶金属配合物电致发光器件的优化也在进行中.     

Structure design for high performance n-type polymer thermoelectric materials

Organic thermoelectric(OTE)materials have been regarded as a potential candidate to harvest waste heat from complex,low temperature surfaces of objects and convert it into electricity.Recently,n-type conjugated polymers as organic thermoelectric materials have aroused intensive research in order to improve their performance to match up with their ptype counterpart.In this review,we discuss aspects that affect the performance of n-type OTEs,and further focus on the effect of planarity of backbone on the doping efficiency and eventually the TE performance.We then summarize strategies such as implementing rigid n-type polymer backbone or modifying conventional polymer building blocks for more planar conformation.In the outlook part,we conclude forementioned devotions and point out new possibility that may promote the future development of this field.