高温AlN插入层对AlGaN/GaN异质结材料和HEMTs器件电学特性的影响

研究了在GaN缓冲层中插入40 nm厚高温AlN层的GaN外延层和AlGaN/GaN异质结材料, AlN插入层可以增加GaN层的面内压应力并提高AlGaN/GaN高电子迁移率晶体管（HEMTs）的电学特性. 在精确测量布拉格衍射角的基础上定量计算了压应力的大小. 增加的压应力一方面通过增强GaN层的压电极化电场, 提高了AlGaN/GaN异质结二维电子气（2DEG）面密度, 另一方面使AlGaN势垒层对2DEG面密度产生的两方面影响相互抵消. 同时, 这种AlN插入层的采用降低了GaN与AlGaN层之间的 关键词： 高温AlN插入层 AlGaN/GaN异质结 二维电子气 应力     

AlGaN/GaN异质结构中极化与势垒层掺杂对二维电子气的影响

从Ⅲ族氮化物中压电极化对应变弛豫度的依赖关系出发，通过自洽求解薛定谔方程和泊松方程,分别研究了自发极化、压电极化和AlGaN势垒层掺杂对AlxGa1-xN/GaN异质结构二维电子气的浓度、分布、面密度以及子带分布等性质的影响.结果表明：二维电子气性质强烈依赖于极化效应,不考虑AlGaN势垒层掺杂，当Al组分为0.3时，由极化导致的二维电子气浓度达1.6×10--13cm-2,其中压电极化对二维电子气贡献为0.7×10-13cm-2，略小于自发极化的贡献(0.9×10-13cm-2)，但为同一数量级，因而通过控制AlGaN层应变而改变极化对于提高二维电子气浓度至关重要. AlGaN势垒层掺杂对二维电子气的影响较弱, 当掺杂浓度从1×10-17增加到1×10-18cm-3时，二维电子气面密度增加0.2×10-13cm-2. 关键词： AlxGa1-xN/GaN 异质结构 二维电子气 自发极化 压电极化     

使用AlN/GaN超晶格势垒层生长高Al组分AlGaN/GaN HEMT结构

在蓝宝石衬底上生长了以AlN/GaN超晶格准AlGaN合金作为势垒的HEMT结构材料,并与传统AlGaN合金势垒样品进行了对比.在高Al组分(≥40%)情况下,超晶格势垒样品的表面形貌明显改进,电学性能特别是2DEG面电子浓度也有所改进.对超晶格势垒生长参数进行了初步优化,使得HEMT结构薄层电阻进一步降低,最后获得了251 Ω/□的薄层电阻. 关键词： AlGaN/GaN 结构 AlN/GaN超晶格 二维电子气 高电子迁移率晶体管     

AlxGa1-x N/GaN调制掺杂异质结构的子带性质研究

通过低温和强磁场下的磁输运测量研究了Al_0.22Ga_0.78N/GaN调制掺杂异质结构中2DEG的子带占据性质和子带输运性质.在该异质结构的磁阻振荡中观察到了双子带占据现象，并发现2DEG的总浓度随第二子带浓度的变化呈线性关系.得到了该异质结构中第二子带被2DEG占据的阈值电子浓度为7.3×10¹²cm^-2.采用迁移率谱技术得到了不同样品的分别对应于第一和第二子带的输运迁移率.发现当样品产生应变弛豫时第一子带的电子迁移 关键词： AlGaN/GaN异质结 二维电子气 子带占据 输运迁移率     

AlN插入层对AlxGa1-xN/GaN界面电子散射的影响

本文研究AlN作为Al_xGa_1-xN/GaN插入层引起的电子输运性质的变化, 考虑了Al_xGa_1-xN和AlN势垒层的自发极化、压电极化对Al_xGa_1-xN/AlN/GaN双异质结高电子迁移率晶体管(HEMT)中极化电荷面密度、二维电子气(2DEG) 浓度的影响, 分析了AlN厚度与界面粗糙度散射和合金无序散射的关系; 结果表明, 2DEG 浓度、界面粗糙度散射和合金无序散射依赖于AlN层厚度, 插入一层1–3 nm薄的AlN层, 可以明显提高电子迁移率.     

InGaN插入层对AlGaN/GaN界面电子散射的影响

本文研究InGaN作为AlGaN/GaN插入层引起的电子输运性质的变化,考虑了AlGaN和InGaN势垒层的自发极化与压电极化对Al_xGa_(1–x)N/In_yGa_(1–y)N/GaN双异质结高电子迁移率晶体管中极化电荷面密度、二维电子气(2DEG)浓度的影响,理论分析了不同In摩尔组分下, InGaN厚度与界面粗糙度散射、随机偶极散射和极性光学声子散射之间的关系.计算结果表明:界面粗糙度散射和随机偶极散射对双异质结Al_xGa_(1–x)N/In_yGa_(1–y)N/GaN的电子输运性质有重要影响,极性光学声子散射对其影响最弱; 2DEG浓度、界面粗糙度散射、随机偶极散射和极性光学声子散射的强弱由InGaN势垒层厚度和In摩尔组分共同决定.     

AlN隔离层生长时间对AlGaN/AlN/GaN HEMT材料电学性能的影响

利用金属有机化学气相沉积（MOCVD）设备,在蓝宝石（0001）面上外延不同生长时间AlN隔离层的Al_xGa_1-xN/AlN/GaN结构的高电子迁移率的晶体管（HEMT）,研究了AlN隔离层厚度对HEMT材料电学性能的影响。研究发现采用脉冲法外延（PALE）技术生长AlN隔离层的时间为12 s（1 nm左右）时,HEMT材料的方块电阻最小,电子迁移率为1 500 cm²·V^-1·s^-1,二维电子气（2DEG）浓度为1.16×10¹³ cm^-2。AFM测试结果表明,一定厚度范围内的AlN隔离层并不会对材料的表面形貌产生重大的影响。HRXRD测试结果表明,AlGaN/AlN/GaN具有好的异质结界面。     

AlGaN/GaN高电子迁移率晶体管肖特基高温退火机理研究

在不同应力条件下,研究了AlGaN/GaN高电子迁移率晶体管高温退火前后的电流崩塌、栅泄漏电流以及击穿电压的变化.结果表明,AlGaN/GaN高电子迁移率晶体管通过肖特基高温退火以后,器件的特性得到很大的改善.利用电镜扫描(SEM)和X射线光电子能谱(XPS)对高温退火前、后的肖特基接触界面进行深入分析,发现器件经过高温退火后,Ni和AlGaN层之间介质的去除,并且AlGaN材料表面附近的陷阱减少,使得肖特基有效势垒提高,从而提高器件的电学特性. 关键词： AlGaN/GaN高电子迁移率晶体管 肖特基接触 界面陷阱     

生物分子膜门电极AlGaN/GaN高电子迁移率晶体管(HEMT)生物传感器研究

设计并制作了结构尺寸为毫米量级的AlGaN/GaN高电子迁移率晶体管(HEMT)生物传感器,采用数值分析的方法分析了器件传感区域长度与宽度比值及待测物调控二维电子气(2DEG)距离与感测信号之间的关系,给出了结构尺寸为毫米量级的AlGaN/GaN HEMT生物传感器的设计依据,以不同浓度的前列腺特异性抗原(PSA)为待测物,对制作的AlGaN/GaN HEMT生物传感器进行了初步测量,测试结果表明,在50 mV的电压下,毫米量级的AlGaN/GaN HEMT生物传感器的对PSA的探测极限低于0.1 pg/ml.实验表明毫米量级的AlGaN/GaN HEMT生物传感器具有灵敏度高,易于集成等优点,具备良好的应用前景.     

1000 V p-GaN混合阳极AlGaN/GaN二极管

GaN材料具有优异的电学特性,如大的禁带宽度(3.4 eV)、高击穿场强(3.3 MV/cm)和高电子迁移率(600 cm~2/(V·s)). AlGaN/GaN异质结由于压电极化和自发极化效应,产生高密度(1×10~(13)cm~(-2))和高迁移率(2000 cm~2/(V·s))的二维电子气(2DEG),在未来的功率系统中, AlGaN/GaN二极管具有极大的应用前景.二极管的开启电压和击穿电压是影响其损耗和功率处理能力的关键参数,本文提出了一种新型的具有高阻盖帽层(high-resistance-cap-layer, HRCL)的p-GaN混合阳极AlGaN/GaN二极管来优化其开启电压和击穿特性.在p-GaN/AlGaN/GaN材料结构基础上,通过自对准的氢等离子体处理技术,在沟道区域形成高阻盖帽层改善电场分布,提高击穿电压,同时在阳极区域保留p-GaN结构,用于耗尽下方的二维电子气,调控开启电压.制备的p-GaN混合阳极(p-GaN HRCL)二极管在阴阳极间距Lac为10μm时,击穿电压大于1 kV,开启电压+1.2 V.实验结果表明, p-GaN混合阳极和高阻GaN盖帽层的引入,有效改善AlGaN/GaN肖特基势垒二极管电学性能.     

Sodium beta-alumina thin films as gate dielectrics for A1GaN/GaN metal-insulator-semiconductor high-electron-mobility transistors

<正>Sodium beta-alumina（SBA） is deposited on AlGaN/GaN by using a co-deposition process with sodium and Al₂O₃ as the precursors.The X-ray diffraction（XRD） spectrum reveals that the deposited thin film is amorphous.The binding energy and composition of the deposited thin film,obtained from the X-ray photoelectron spectroscopy（XPS） measurement,are consistent with those of SBA.The dielectric constant of the SBA thin film is about 50.Each of the capacitance-voltage characteristics obtained at five different frequencies shows a high-quality interface between SBA and AlGaN.The interface trap density of metal-insulator-semiconductor high-electron-mobility transistor（MISHEMT） is measured to be（3.5～9.5）×10¹⁰ cm^-2·eV^-1 by the conductance method.The fixed charge density of SBA dielectric is on the order of 2.7×10¹² cm^-2.Compared with the AlGaN/GaN metal-semiconductor heterostructure high-electronmobility transistor（MESHEMT）,the AlGaN/GaN MISHEMT usually has a threshold voltage that shifts negatively. However,the threshold voltage of the AlGaN/GaN MISHEMT using SBA as the gate dielectric shifts positively from—5.5 V to—3.5 V.From XPS results,the surface valence-band maximum（VBM-E_F） of AlGaN is found to decrease from 2.56 eV to 2.25 eV after the SBA thin film deposition.The possible reasons why the threshold voltage of AlGaN/GaN MISHEMT with the SBA gate dielectric shifts positively are the influence of SBA on surface valence-band maximum （VBM-E_F）,the reduction of interface traps and the effects of sodium ions,and/or the fixed charges in SBA on the two-dimensional electron gas（2DEG）.     

Magnetotransport properties of two-dimensional electron gas in AlGaN/AlN/GaN heterostructures

Magnetotransport measurements are carried out on the AlGaN/AlN/GaN in an SiC heterostructure, which demonstrates the existence of the high-quality two-dimensional electron gas (2DGE) at the AlN/GaN interface. While the carrier concentration reaches 1.32 × 10¹³ cm ^{- 2} and stays relatively unchanged with the decreasing temperature, the mobility of the 2DEG increases to 1.21 × 10⁴ cm²/(V·s) at 2 K. The Shubnikov—de Haas (SdH) oscillations are observed in a magnetic field as low as 2.5 T at 2 K. By the measurements and the analyses of the temperature-dependent SdH oscillations, the effective mass of the 2DEG is determined. The ratio of the transport lifetime to the quantum scattering time is 9 in our sample, indicating that small-angle scattering is predominant.     

N极性GaN/AlGaN异质结二维电子气模拟

通过自洽求解薛定谔方程和泊松方程,较系统地研究了GaN沟道层、AlGaN背势垒层、Si掺杂和AlN插入层对N极性GaN/AlGaN异质结中二维电子气(2DEG)的影响,分析表明,GaN沟道层厚度、AlGaN背势垒层厚度及Al组分变大都能一定程度上提高二维电子气面密度,AlGaN背势垒层的厚度和Al组分变大也可提高二维电子气限阈性,且不同的Si掺杂形式对二维电子气的影响也有差异,而AlN插入层在提高器件二维电子气面密度、限阈性等方面表现都较为突出,在模拟中GaN沟道层厚度小于5nm时无法形成二维电子气,超过20nm后二维电子气面密度趋于饱和,而AlGaN背势垒厚度超过40nm后二维电子气也有饱和趋势,对均匀掺杂和delta掺杂而言AlGaN背势垒层Si掺杂浓度超过5×10~(19)cm~(-3)后2DEG面密度开始饱和,而厚度为2nmAlN插入层的引入会使2DEG面密度从无AlN插入层时的0.93×10~(13)cm~(-2)提高到1.17×10~(13)cm~(-2)。     

Influence of contact shape on AlGaN/GaN Schottky diode prepared on Si with thick buffer layer

A report on the fabrication and characterization of high performance conventional and ring-shaped AlGaN/GaN Schottky barrier diode on Si is presented. The resulting device exhibited low leakage current, which led to a detectivity performance of 3.48×10¹³ and 1.76×10¹³ cm?Hz^1/2 W^?1, respectively, for both conventional and ring-shaped Schottky diode. The differential resistances of both devices were obtained at approximately 1.37×10¹² and 1.41×10¹³ Ω, respectively. The zero bias peak responsivities of conventional and ring-shaped Schottky diodes were estimated to be 3.18 and 2.08 A?cm^?2/W, respectively. The typical UV to visible rejection ratio was observed over three orders of magnitude at zero bias. The C–V measurements was used to calculate and analyze the polarization sheet charge density of the AlGaN barrier layer by using self-consistently solving Schrodinger’s and Poisson’s equations. It is demonstrated that the ring shape of the Schottky barrier has higher polarization sheet charge density, which has the consequence that the Schottky shape has influence on the strain of the AlGaN barrier layer.     

Optimization of two-dimensional electron gases and – characteristics for AlGaN/GaN HEMT devices

In this paper, we take account of the spontaneous and piezoelectric polarization effect at the heterointerface in the AlGaN/GaN HEMT device, and one-dimensional Schrödinger–Poisson equations are solved self-consistently using a nonuniform mesh; using our findings, the AlGaN/GaN heterostructure conduction band and the two-dimensional electron gas (2DEG) density are investigated. The dependences of the 2DEG characteristics on the Al fraction, the thickness of each layer, the donor concentration and the gate voltage are investigated through simulation. The output characteristics are simulated using a quasi-2D model; a saturation voltage and threshold voltage are also shown. The influence of the spacer layer width on the 2DEG density is calculated for the first time. An explanation and analyses are given.     

高电子迁移率晶格匹配InAlN/GaN材料研究

文章基于蓝宝石衬底采用脉冲金属有机物化学气相淀积(MOCVD)法生长的高迁移率InAlN/GaN材料,其霍尔迁移率在室温和77 K下分别达到949和2032 cm²/Vs,材料中形成了二维电子气(2DEG). 进一步引入1.2 nm的AlN界面插入层形成InAlN/AlN/GaN结构,则霍尔迁移率在室温和77 K下分别上升到1437和5308 cm²/Vs. 分析样品的X射线衍射、原子力显微镜测试结果以及脉冲MOCVD生长方法的特点,发现InAlN/GaN材料的结晶质量较高,与GaN晶格匹配的InAlN材料具有平滑的表面和界面. InAlN/GaN和InAlN/AlN/GaN材料形成高迁移率特性的主要原因归结为形成了密度相对较低(1.6×10¹³-1.8×10¹³ cm^-2)的2DEG,高质量的InAlN晶体降低了组分不均匀分布引起的合金无序散射,以及2DEG所在界面的粗糙度较小,削弱了界面粗糙度散射. 关键词： InAlN/GaN 脉冲金属有机物化学气相淀积 二维电子气 迁移率     

Effects of donor density and temperature on electron systems in AlGaN/AlN/GaN and AlGaN/GaN structures

It was reported by Shen et al that the two-dimensional electron gas (2DEG) in an AlGaN/AlN/GaN structure showed high density and improved mobility compared with an AlGaN/GaN structure, but the potential of the AlGaN/AlN/GaN structure needs further exploration. By the self-consistent solving of one-dimensional Schr\"{o}dinger--Poisson equations, theoretical investigation is carried out about the effects of donor density (0--1\times 10¹⁹cm^-3 and temperature (50--500K) on the electron systems in the AlGaN/AlN/GaN and AlGaN/GaN structures. It is found that in the former structure, since the effective \Delta E_c is larger, the efficiency with which the 2DEG absorbs the electrons originating from donor ionization is higher, the resistance to parallel conduction is stronger, and the deterioration of 2DEG mobility is slower as the donor density rises. When temperature rises, the three-dimensional properties of the whole electron system become prominent for both of the structures, but the stability of 2DEG is higher in the former structure, which is also ascribed to the larger effective \Delta E_c. The Capacitance--Voltage (C-V) carrier density profiles at different temperatures are measured for two Schottky diodes on the considered heterostructure samples separately, showing obviously different 2DEG densities. And the temperature-dependent tendency of the experimental curves agrees well with our calculations.     

Characterization of GaN/AlGaN epitaxial layers grown by metalorganic chemical vapour deposition for high electron mobility transistor applications

GaN and AlGaN epitaxial layers are grown by a metalorganic chemical vapour deposition (MOCVD) system. The crystalline quality of these epitaxially grown layers is studied by different characterization techniques. PL measurements indicate band edge emission peak at 363.8 nm and 312 nm for GaN and AlGaN layers respectively. High resolution XRD (HRXRD) peaks show FWHM of 272 and 296 arcsec for the (0 0 0 2) plane of GaN and GaN in GaN/AlGaN respectively. For GaN buffer layer, the Hall mobility is 346 cm²/V-s and carrier concentration is 4.5 × 10¹⁶/cm³. AFM studies on GaN buffer layer show a dislocation density of 2 × 10⁸/cm² by wet etching in hot phosphoric acid. The refractive indices of GaN buffer layer on sapphire at 633 nm are 2.3544 and 2.1515 for TE and TM modes respectively.