低频段紧凑型同轴相对论返波振荡器

基于P波段新型三周期慢波结构同轴相对论返波振荡器设计思想,设计了一个L波段同轴相对论返波振荡器。粒子模拟表明,在二极管电压591 kV、电流8.2 kA、导引磁场0.8 T时,获得了1.50 GW的微波输出,频率为1.64 GHz,效率达31%,器件慢波结构尺寸仅为f96 mm207 mm。分析了该器件实际高频结构的电动力学特性,重点研究了纵向谐振模式、品质因数等特点,并结合P波段的研究结果,得到了该类器件的相关设计指标:慢波结构长度约为一个波长,波纹周期约5/13波长,外波纹深度约1/10波长,内波纹深度约1/30波长,电子束半径约0.7倍外波纹平均半径,器件的纵向工作模式为0.8模,对应的Q值约16。     

S波段长脉冲相对论返波振荡器实验研究

从物理机制上定性地分析了导致脉冲缩短的主要原因,给出了长脉冲重复频率运行下的相对论返波振荡器(RBWO)设计原则。结合传统谐振式返波振荡器的基本设计理论,设计和模拟优化了工作在S波段的长脉冲RBWO,并利用本实验室现有长脉冲脉冲功率驱动源开展了S波段长脉冲RBWO的实验研究。实验结果表明:在单次运行条件下,微波输出功率达到约2 GW、脉宽约90 ns;在10 Hz重复频率运行条件下,输出微波功率达到约1 GW、脉宽约100 ns。器件产生的微波频率为3.6 GHz,输出模式为TM01模,效率约20%。对实验结果分析表明,器件截止颈和第一个慢波结构结合处的爆炸发射是导致脉冲缩短的主要原因之一。     

紧凑型L波段同轴相对论返波振荡器的粒子模拟

 设计了紧凑型L波段同轴相对论返波振荡器，通过粒子模拟研究了L波段同轴相对论返波振荡器相互作用的物理过程，并对器件的电磁结构进行了优化和改进。分析表明，采用同轴慢波结构可以在较低的外加磁场下实现L波段返波振荡器的微波输出，同时可以大大减小微波器件的径向尺寸。这是因为同轴慢波结构的TM01模式有类似于TEM模的性质，没有截止频率，但纵向电场不为零，电子束能够与它发生强相互作用过程。粒子模拟优化结果表明，在器件半径仅为4.0 cm，电子束能量240 keV，电子束流1.8 kA，导引磁场仅为0.75 T时，返波振荡器可以在频率1.60 GHz处获得较大功率的微波输出， 平均峰值功率达140 MW，平均峰值功率效率约为32%。     

阳极结构对过模返波振荡器长脉冲工作特性的影响

针对过模返波振荡器中泄漏微波在二极管区谐振, 造成微波脉冲缩短的现象, 设计了内置吸波材料的阳极结构来抑制这种泄漏微波对器件输出的影响。利用粒子模拟软件对不同阳极结构下过模返波管微波输出特性进行模拟研究, 模拟结果表明, 带吸波材料的阳极结构可以减小泄漏微波对微波输出功率、器件工作模式及脉冲宽度的影响。在长脉冲过模返波振荡器实验中, 电子束参数为（800 kV, 7 kA）时, 器件输出微波频率为8.58 GHz, 效率为30%。通过模拟计算和实验验证, 这种带吸波材料的阳极结构有效降低了泄漏微波对过模返波管微波输出的影响, 将器件输出微波脉冲宽度从70 ns提高到110 ns。     

三种同轴双波纹周期慢波结构对比研究

利用Fourier级数展开法,给出了任意几何结构的表达式的求解方法.通过数值计算,对比分析了余弦、梯形和矩形波纹慢波结构(slow-wave structure,SWS)的色散特性.根据S参数理论,研究了这三种SWS纵向模式选择的特性,提出了在同轴慢波器件中加入同轴引出结构,可减少所需SWS周期数,不但使器件结构更为紧凑,还可避免纵模竞争从而提高器件效率、稳定产生微波频率.进一步通过KARAT 2.5维全电磁粒子模拟程序,探讨了分别采用三种SWS的相对论返波振荡器(backward-wave oscillator,BWO)的束-波作用的物理过程,设计了一种紧凑型、吉瓦级、同轴L波段BWO,分析了不同形状SWS的选取原则.在此基础上,开展了初步实验研究：在二极管电压为670 kV,电子束流为107 kA,引导磁场为075 T的条件下,输出微波峰值功率约为102 GW,微波波形半高宽为22 ns,功率转换效率约为142%,频率为161 GHz. 关键词： 同轴慢波结构 相对论返波振荡器 色散特性 高功率微波     

梯形波纹同轴慢波结构色散特性及其纵向谐振特性

 利用傅里叶级数展开,给出了一种求解梯形慢波结构表达式的方法。通过数值模拟,研究了级数展开次数对求解精度的影响。当级数为10阶时,线型拟合而成的结构与原结构吻合较好。利用此表达式数值求解了色散方程,得到两个最低阶模quasi-TEM模和A 模。分析了为实现电子束与quasi-TEM模的-1次空间谐波相互作用慢波结构参数所需满足的条件,并指出利用此条件下纵向电场具有表面波的特点可实现横向模式选择。采用S参数理论研究有限长慢波结构的纵向谐振特性,提出在同轴慢波器件中加入同轴引出结构可减少所需慢波结构周期数,这不但使器件结构更为紧凑,还可避免纵模竞争从而提高器件效率、稳定产生微波频率。在此基础上设计了一种L波段同轴相对论返波振荡器,采用KARAT 2.5维全电磁粒子模拟程序研究了器件内束-波作用的物理过程。模拟结果表明,该器件具有径向尺寸小、束-波作用效率高的特点。在电子束能量700 keV、电子束流11.5 kA的条件下,器件在频率1.6 GHz处获得较高的微波输出,饱和后微波的平均功率达2.60 GW,平均效率约为32.3%。     

紧凑型P波段相对论返波振荡器的粒子模拟

 设计了一种紧凑型P波段相对论返波振荡器,其电动力学结构是由同轴慢波结构和同轴引出结构组成的。同轴慢波结构缩小了器件的径向尺寸;同轴引出结构缩短了器件的轴向长度,且提高了束波作用效率。通过粒子模拟研究了器件内束波作用的物理过程,模拟结果表明：器件具有结构紧凑、束波作用效率高的特点。在二极管电压700 kV,电流7 kA,导引磁场1.5 T时,器件在频率833 MHz处获得较高的微波输出,饱和后输出微波的平均功率达1.58 GW,效率约为32%,器件电磁结构尺寸仅为108 mm×856 mm。     

频率色散表面阻抗对真空电子太赫兹源的影响

为了研究欧姆损耗对高频真空电子器件工作特性的影响,首先推导频率色散表面阻抗边界在三维共形粒子模拟软件UNIPIC-3D中的实现原理,并通过对有耗边界矩形谐振腔和圆波导进行模拟验证了该阻抗边界算法的正确性.采用有耗共形UNIPIC-3D模拟相对论太赫兹表面波振荡器和低电压平板格栅返波振荡器.模拟结果表明,对于表面波振荡器和平板BWO这种电磁场集中在金属慢波结构附近的太赫兹真空电子器件,欧姆损耗会对器件的运行带来极大影响,对于采用铜材料的器件,输出功率会下降一半左右,器件起振时间出现延迟,但器件工作频率几乎不变.为了提高相对论太赫兹表面波振荡器的效率,在二极管和慢波结构之间增加了反射腔,模拟结果表明,在考虑器件表面损耗的条件下,器件的工作频率保持不变,输出功率由41 MW提高到60 MW.     

无外加引导磁场相对论返波振荡器粒子模拟

设计了一种无外加引导磁场S波段相对论返波振荡器,采用阳极网提取电子,并设计了非均匀慢波结构。通过Karat 2.5维全电磁粒子模拟程序研究了器件内束-波作用的物理过程。典型模拟结果为:当二极管工作电压330 kV、电流2.83 kA时,器件在频率2.79 GHz处获得较高的微波输出,经27 ns后饱和,输出微波的功率达158 MW,效率约为16.8%。     

同轴引出电子束相对论返波振荡器的粒子模拟

 设计了一种L波段同轴引出电子束相对论返波振荡器,采用KARAT 2.5维全电磁粒子模拟程序研究了器件内束-波作用的物理过程,分析了二极管电压和导引磁场对产生微波频率和束-波转换效率的影响。模拟结果表明:该器件在小型化,中等磁场的条件下具有较高的束-波作用效率。在电子束能量700 keV,电子束流10 kA,导引磁场为1.0 T时,器件在频率1.62 GHz处获得较高的微波输出,饱和后微波的平均功率达2.2 GW,平均效率约为30%,器件最大径向半径仅为5.0 cm。     

基于混合控制LLC谐振变换器的设计与分析

根据半桥LLC谐振变换器的拓扑结构,采用了一种混合控制方式,整合了电荷控制和传统频率控制两种控制方式。与目前的电荷型控制、双频率控制等常用控制方式相比,该控制方式增加的频率补偿斜坡,使得补偿器的设计十分简单,改进的线路瞬态性能可降低输出电容器值。根据基波分析法得到半桥LLC谐振变换器等效电路,确定了直流增益与品质因数、归一化频率和谐振电感与励磁电感的比值之间的关系式,并由该关系式设计出合适的谐振器件参数。通过混合控制方式与设计的LLC谐振参数搭建了一台5 kW/±85 V半桥LLC谐振变换器进行实验验证,实验结果显示,该样机动态特性良好,能够得到稳定的输出电压和具有较高的传输效率,验证了所采用的控制方法和基波分析法设计的LLC谐振参数的可行性。     

带有反射腔的相对论返波管的数值模拟

 阐述了带有反射腔的相对论返波管的数值模拟研究。利用线性理论[1]设计了返波管的慢波结构，应用SUPERFISH软件设计了谐振反射器。用KARAT软件对谐振反射腔返波管进行了宏观粒子模拟，得到了优化的返波管结构参数，并研究了外加磁场对输出效率的影响。模拟结果表明：谐振反射腔不仅起到截止颈的作用，还有预调制的作用；在低外加磁场条件下，该返波管也能输出较高功率的微波。显示了其在重复频率工作方面的重要意义。     

ZnO-based film bulk acoustic resonator devices on a specially designed Bragg reflector

In this paper, we studied ZnO-based film bulk acoustic resonator (FBAR) device fabricated on a specially designed multilayered Bragg reflector part. Very thin chromium adhesion layers (0.03 μm thick) were additionally deposited to improve the quality of the Bragg reflector and some thermal treatments were performed to improve the resonant characteristics of the FBAR device. At the operating frequency of ∼2.7 GHz, excellent resonant characteristics were observed in terms of return loss and quality factor, and effective electromechanical coupling coefficient.     

Extremely wide band Rayleigh resonant reflector with sharp angular spectra in near infrared wavelength band

In this paper, we propose an extremely broadband Rayleigh resonant reflector with sharp angular spectra operating in near infrared wavelength band, this device consisting of a single germanium resonant grating layer is designed and analyzed by using with the rigorous vector diffraction theory. At the Rayleigh angle, the first diffracted order can be appear from evanescent to a propagating one, thus, a very sharp angular spectrum characteristics can be presented in the device. Based on the guided mode resonant effect, high index material such as silicon and germanium can be designed as wide band reflector, beam splitter and polarizer in near infrared wavelength region. Through connecting Rayleigh phenomena and guided mode resonant effect, we can design a new kind of optical devices with versatile characteristics such as sharp angular spectra and extremely wide reflection band. In this paper, we present a Rayleigh resonant reflector with extremely high reflection (R > 99.5%) for TE polarization light over ∼600 nm wavelength range and sharp angular spectral distribution. In addition, it is shown from our calculations that the high-index nano-layer located adjacent to the substrate is seen to critically affect the resulting spectra of Rayleigh resonant reflector.     

一种新型高效光子晶体多信道下载滤波器的设计

采用二维正方排列的光子晶体,根据微腔缺陷模和波导模共振耦合原理,设计了一种新型的多信道下载滤波器,该滤波器通过主波导、90°弯波导和共振微腔的组合,提高了各个信道下载波导的下载效率。利用二维时域有限差分法模拟了滤波器的传输特性,并理论分析了影响下载效率的因素,进一步对滤波器进行了优化,使得各信道下载波导的下载效率均在91%以上。模拟结果表明该滤波器能有效地实现光波的分波下载,传输谱信道波长间隔约为20nm,中心波长误差为±2nm,传输谱的最大半宽度为3.2nm,有良好的波长选择性,证实了增大下载波导和共振微腔的耦合区域可以有效地提高滤波器的下载效率。     

A novel overmoded slow-wave high-power microwave (HPM) Generator

We present the design and experimental results of a novel overmoded slow-wave high-power microwave (HPM) generator that is featured by its compactness, low-operation magnetic field, and potentially high power and high efficiency. The device includes two slow-wave structure (SWS) sections, a resonant cavity, and a tapered waveguide. The resonant cavity was well designed and was used to achieve the axial mode selection and to decrease the length of the SWS sections. The radial mode selection is achieved using the property of "surface wave" of the device to excite the TM/sub 01/ mode while making the higher TM/sub 0n/ modes unexcited. The physical mechanisms of axial and radial mode selections ensure that the microwave is produced with a single mode and a narrow band. The feasibility of low magnetic field operation is also investigated based on the characteristics of the overmoded slow-wave devices. Experiments were carried out at the Spark-2 accelerator. At diode voltage of 474 kV, beam current of 5.2 kA, and guiding magnetic field strength of 0.6 T, a microwave was generated with power of 510 MW, mode of TM/sub 01/, and frequency of 9.54 GHz. The relative half width of the frequency spectrum is /spl Delta/f/f= 0.6%, and the beam-to-microwave efficiency is about 21% in our experiment.     

Red top-emitting organic light-emitting device with improved efficiency and saturated color

In this work, characteristics of microcavity top-emitting red organic light-emitting device (TEROLED) having metallic electrodes had been examined. The TEOLED shows the higher efficiency in comparison with that of the bottom OLED. However, color variation with the increasing view angles is also observed. For the purpose of diminishing the blue-shift of resonant wavelength (RW) in the device with increasing view angle, the effect of out-coupling layer on the emission properties of the TEOLED is discussed in detail. Finally, the out-coupling layer was introduced in theory without sacrificing the efficiency through precise optical simulation.     

可见光波段双层浮雕型导模共振滤波器设计与分析

基于傅里叶模式理论分析了双层浮雕型导模共振光栅的共振效应,分别讨论了光栅的槽深、剩余厚度、周期以及填充系数对峰值反射率、带宽、旁带反射率的影响. 数据计算表明,欠刻蚀情形的误差宽容度远远优于过刻蚀情形,两者在光栅槽深相对误差小于15％的范围内,都能保证共振峰的衍射效率高于99.5%,在相同的误差范围内,共振峰线宽的相对误差将分别达到7％和60％,因此厚度误差集中反映在对共振线宽的改变上. 另外,光栅周期和填充系数的变化将明显改变共振峰中心波长和线宽. 关键词： 导模共振 平面波导 窄带滤波     

Normal-incidence guided-mode resonant grating filters: design and experimental demonstration

Guided-mode resonant grating filters have numerous applications. However, in weakly modulated gratings designed for use at normal incidence, the filtering resonance of these subwavelength-period devices splits for angles of incidence that are even slightly off normal incidence. Strongly modulated gratings are designed that essentially overcome this practical problem near normal incidence. In addition, these gratings can have, by design, either broad or narrow spectral characteristics. An experimental demonstration (1.5-2.0-mu m wavelength range) of such a normal-incidence guided-mode resonant silicon grating upon a sapphire substrate is presented. The measured reflection resonance had a FWHM of 67-100 nm for angles of incidence of 0-8 degrees and peak efficiency of ~80% .     

Effect of bending on characteristics of a polymer microring resonant wavelength multiplexer

Novel formulas of transfer functions are presented, some parameters are optimized, and bending effect of microrings on characteristics is analyzed for a polymer microring resonant wavelength multiplexer (MRRWM) around the central resonant wavelength of 1.55 μm with the wavelength spacing of 1.6 nm and with eight vertical output channels. Simulated results show that the bending of microrings causes the variation of the propagation constant, leads to the shift of the transmission spectrum, and increases the insertion loss. A method is proposed for eliminating the shift of the transmission spectrum and realizing the accurate demultiplexing of the device. The polymer MRRWM designed possesses the 3-dB bandwidth of 0.2 μm, insertion loss less than 0.57 dB, and crosstalk below −20 dB for every vertical output channel.