平板集热太阳热电器件建模及结构优化

太阳能热电转换是光伏效应外另一种直接将太阳辐射转变为电能的途径, 近年来已经成为太阳能利用的热点之一. 本文以Bi₂Te₃材料为基础构建平板集热太阳热电器件模型, 采用有限元法分析AM1.5辐射条件下器件温度分布情况, 并结合基于温度的物性参数计算集热比、热臂截面积与长度变化等因素对器件的开路电压、 最大输出功率及转化效率的影响. 研究发现: 集热比与热臂长度的变化对器件性能有显著影响, 热臂截面积的变化对器件转化效率影响相对较弱; 在这一模型中, 平板集热太阳热电器件的转化效率达到1.56%.     

Graphene for Thermoelectric Applications: Prospects and Challenges

Thermoelectric power generators require high-efficiency thermoelectric materials to transform waste heat into usable electrical energy. An efficient thermoelectric material should have high Seebeck coefficient and excellent electrical conductivity as well as low thermal conductivity. Graphene, the first truly 2D nanomaterial, exhibits unique properties which suit it for use in thermoelectric power generators, but its application in thermoelectrics is limited by the high thermal conductivity and low Seebeck coefficient resulting from its gapless spectrum. However, with the possibility of modification of graphene's band structure to enhance Seebeck coefficient and the reduction of its thermal conductivity, it is an exciting prospect for application in thermoelectric power generation. This article examines the electronic, optical, thermal, and thermoelectric properties of graphene systems. The factors that contribute to these material properties in graphene systems like charge carriers scattering mechanisms are discussed. A salient aspect of this article is a synergistic perspective on the reduction of thermal conductivity and improvement of Seebeck coefficient of graphene for a higher thermoelectric energy conversion efficiency. In this regard, the effect of graphene nanostructuring and doping, forming of structural defects, as well as graphene integration into a polymer matrix on its thermal conductivity and Seebeck coefficient is elucidated.     

热光伏能量转换器件的热力学极限与优化性能预测

受不可逆损失的影响,热光伏能量转换器件在高品位热能回收与利用方面受到限制.本文揭示不可逆损失来源,提供热光伏能量转换器件性能提升方案.利用半导体物理和普朗克热辐射理论,确定热光伏能量转换器件在理想条件下的最大效率.进而考虑Auger与Shockley-Reed-Hall非辐射复合和不可逆传热损失对光伏电池的电学、光学和热学特性的影响,预测热光伏器件优化性能.确定功率密度、效率和光子截止能量的优化区间.结果表明:相比于理想热光伏器件,非理想热光伏器件的开路电压、短路电流密度和效率有所降低;优化热光伏电池电压、光子截止能量和热源温度,可提升器件的功率密度和效率.通过对比发现理论与实验结果较一致,所得结果可为实际热光伏能量转换器件的研制提供理论指导.     

Demonstration of polycrystalline thin film coatings on glass for spin Seebeck energy harvesting

The spin Seebeck effect, a newly discovered phenomena, has been suggested as a potential ‘game changer’ for thermoelectric technology due to the possibility of separating the electric and thermal conductivities. This is due to a completely different device architecture where, instead of an arrangement of p‐ and n‐type pillars between two ceramic blocks, a thermopile could be deposited directly onto a magnetic film of interest. Here we report on the spin Seebeck effect in polycrystalline Fe₃O₄:Pt bilayers deposited onto amorphous glass substrates with a view for economically viable energy harvesting. Crucially, these films exhibit large coercive fields (197 Oe) and retain 75% of saturation magnetisation, in conjunction with energy conversion comparable to epitaxially grown films. This demonstrates the potential of this technology for widespread application in harvesting waste heat for electricity.     

Optimization of a New Design of Molten Salt-to-CO2 Heat Exchanger Using Exergy Destruction Minimization

One of the ways to make cost-competitive electricity, from concentrated solar thermal energy, is increasing the thermoelectric conversion efficiency. To achieve this objective, the most promising scheme is a molten salt central receiver, coupled to a supercritical carbon dioxide cycle. A key element to be developed in this scheme is the molten salt-to-CO₂ heat exchanger. This paper presents a heat exchanger design that avoids the molten salt plugging and the mechanical stress due to the high pressure of the CO₂, while improving the heat transfer of the supercritical phase, due to its compactness with a high heat transfer area. This design is based on a honeycomb-like configuration, in which a thermal unit consists of a circular channel for the molten salt surrounded by six smaller trapezoidal ducts for the CO₂. Further, an optimization based on the exergy destruction minimization has been accomplished, obtained the best working conditions of this heat exchanger: a temperature approach of 50 °C between both streams and a CO₂ pressure drop of 2.7 bar.     

Conversion of environmental heat to electric energy in the metal-dielectric-semiconductor-metal system

The basis of the proposed converter is a thermoelectric capacitor, which is the system of a metal-dielectric-semiconductor-metal. In such a system, non-zero conversion of the environmental heat into electrical energy without preliminarily creating a temperature gradient is possible. Charging of the thermoelectric capacitor takes place through the bottom electrode of the semiconductor substrate and discharging takes place through the near-surface layer enriched electrons formed during charging in the near-surface layer on the boundary with the dielectric. In this case, the amount of absorbed heat at the capacitor charging in the contact of the metal-semiconductor is greater than being allocated heat at the discharge. This is due to the fact that the contact difference between the bottom electrode and semiconductor is more than the contact difference between the metal and near-surface enriched layer in which the concentration of electrons is significantly more than in the volume of a semiconductor. As a result, the absorbed heat, which is not emitted, is converted into electrical energy at the discharge according to the law of conservation of energy.     

Thermoelectric power generation in a thermoacoustic refrigerator

Commercially available solid-state thermoelectric devices may be used for their electrical power generation capabilities when coupled to a thermoacoustic refrigerator or heat pump. General performance characteristics as well as bulk thermal conductivity for a selection of thermoelectric elements was first found by using a two-plate apparatus to maintain a constant temperature difference across the element. Further studies of an element’s performance when placed in series with the thermoacoustic refrigerator’s heat exchangers will be presented. Design considerations for using thermoelectric elements in a no-moving parts electrical power generation scheme will be discussed.     

具有本征低晶格热导率的硫化银快离子导体的热电性能

硫化银(Ag_2S)是一种典型的快离子导体材料,前期关于Ag_2S的研究主要集中在光电和生物等领域.最近的研究表明, a-Ag_2S具有和金属一样的良好延展性和变形能力.但是, Ag_2S的热电性能尚无公开报道.本工作合成了单相Ag_2S化合物,系统研究了其在300—600 K范围的物相变化、离子迁移特性和电热输运性质.研究发现, Ag_2S在300—600 K温度区间表现出半导体的电输运性质.由于单斜-体心立方相晶体结构转变, Ag_2S的离子电导率、载流子浓度、迁移率、电导率、泽贝克系数等性质在455 K前后出现急剧变化.在550 K, Ag_2S的功率因子最高可达5μW·cm~(–1)·K~(–2). Ag_2S在300—600 K温度区间均表现出本征的低晶格热导率(低于0.6 W·m~(–1)·K~(–1)). S亚晶格中随机分布的类液态Ag离子是导致b-Ag_2S体心立方相具有低晶格热导率的主要原因.在573 K, Ag_2S的热电优值可达0.55,与Ag_2Se, Ag_2Te, CuAgSe等已报道的Ag基快离子导体热电材料的性能相当.     

Micro thermoelectric devices: From principles to innovative applications

Thermoelectric devices (TEDs), including thermoelectric generators (TEGs) and thermoelectric coolers (TECs) based on the Seebeck and Peltier effects, respectively, are capable of converting heat directly into electricity and vice versa. Tough suffering from low energy conversion efficiency and relatively high capital cost, TEDs have found niche applications, such as the remote power source for spacecraft, solid-state refrigerators, waste heat recycling, and so on. In particular, on-chip integrable micro thermoelectric devices (μ-TEDs), which can realize local thermal management, on-site temperature sensing, and energy harvesting under minor temperature gradient, could play an important role in biological sensing and cell cultivation, self-powered Internet of Things (IoT), and wearable electronics. In this review, starting from the basic principles of thermoelectric devices, we summarize the most critical parameters for μ-TEDs, design guidelines, and most recent advances in the fabrication process. In addition, some innovative applications of μ-TEDs, such as in combination with microfluidics and photonics, are demonstrated in detail.     

Research status and performance optimization of medium-temperature thermoelectric material SnTe

Thermoelectric materials have the ability to directly convert heat into electricity, which have been extensively studied for decades to solve global energy shortages and environmental problems. As a medium temperature (400-800 K) thermoelectric material, SnTe has attracted extensive attention as a promising substitute for PbTe due to its non-toxic characteristics. In this paper, the research status of SnTe thermoelectric materials is reviewed, and the strategies to improve its performance are summarized and discussed in terms of electrical and thermal transport properties. This comprehensive discussion will provides guidance and inspiration for the research on SnTe.     

Evaluating the efficiency of thermo-electric conversion of heat from gas combustion in a small-scale system with counterflow heat exchange

The efficiency of thermoelectric conversion of heat from gas combustion was evaluated in a small-scale system consisting of two channels with opposing gas flows and thermocouples located in the separating wall. Combustion occurred in the chamber fed with fresh mixture heated by combustion products through heat-conducting walls of the channel. In the channel walls, there were thermoelectric converters. It has been shown that in this system, the maximum conversion efficiency of heat from gas combustion may be close to the maximum efficiency of thermoelectric conversion calculated by the maximum acceptable working temperature of the hot side of the converter. This conclusion is valid in the case when the adiabatic combustion temperature of the gas mixture is below the maximum allowable operating temperature of the hot side of the thermoelectric converter. The considered system is promising for the burning of low-calorific gas mixtures and does not require additional energy for cooling the cold side of the thermoelectric converter.     

Macro-performance of multilayered thermoelectric medium

The effective properties of thermoelectric composites are well known to depend on boundary conditions, which causes the macro performance of thermoelectric composite to be difficult to assess. The overall macro-performance of multilayered thermoelectric medium is discussed in this paper. The analytical solutions are obtained, including the heat flux, temperature,electric potential, and the overall energy conversion efficiency. The results show that there are unique relationships between the temperature/electric potential and the electric current/energy flux in the material, and whether the material is independent of or embedded in thermoelectric composites. Besides, the Peltier effect at the interface can significantly improve the overall energy conversion efficiency of thermoelectric composites. These results provide a powerful tool to analyze the effective behaviors of thermoelectric composites.     

Thermoelectric effect in a serial two-quantum-dot

We study the thermoelectric effect in a serial-coupled two quantum dots (QDs) device in the Coulomb blockade regime. The electrical conductance, the thermal conductance, the thermopower, and the thermoelectrical figure of merit are calculated by using the Green's function method. It is found that the energy levels of the two dots are split into a series of molecular states, where the electrical and the thermal conductances show resonance peaks. These peaks in the electrical conductance are eliminated by the increase of the temperature, while those in the thermal conductance are enhanced because of the bipolar effect. In quite high temperature regime, the figure of merit has two huge peaks with maximums exceeding 20 in the vicinity of the electron-hole symmetry point. The magnitude of the figure of merit will be suppressed for unequal dots' levels, but is enhanced by the asymmetry of the dot-lead coupling strengths.     

稳态平板法在热电器件热电转换效率测试中的应用

将稳态平板法测导热系数的实验应用于热电器件热电转换效率的测试,通过测量输入器件的传热速率和负载的输出电功获得热电器件的热电转换效率。研究发现,稳态平板法可以测量工作温度在室温到100℃范围内热电器件的热电转换效率。     

Study on the thermoelectric properties of porous Bi-Te films deposited using thermal evaporation on AAO template

The application of thermoelectric films is limited to retain the temperature gradient. In this study, the Bi-Te films are deposited on the AAO template with a pore size of 100 nm using thermal evaporation. The results show that the conductive types of the Bi-Te film are tuned by source temperature. The power factor of the p-type porous film decreases 36% by comparing to that of the p-type nonporous film (1020 μW/mK² at 250 °C). Meanwhile, the temperature difference in the porous device is maintained and is approximately 5.0 °C. Thus, the maximum output power is achieved in the porous device (about 25 pW), which is 5 times higher than that of the nonporous device. This provides a method to improve the conversion efficiency of thermoelectric film device by maintaining the temperature difference by using porous structure.     

Stimulated radiative laser cooling

Building a refrigerator based on the conversion of heat into optical energy is an ongoing engineering challenge. Under well-defined conditions, spontaneous anti-Stokes fluorescence of a dopant material in a host matrix is capable of lowering the host temperature. The fluorescence is conveying away a part of the thermal energy stored in the vibrational oscillations of the host lattice. In particular, applying this principle to the cooling of (solid-state) lasers opens up many potential device applications, especially in the domain of high-power lasers. In this paper, an alternative optical cooling scheme is outlined, leading to the radiative cooling of solid-state lasers. It is based on converting the thermal energy stored in the host into optical energy by means of a stimulated nonlinear process, rather than a spontaneous process. This should lead to better cooling efficiencies and a higher potential of applying the principle for device applications.     

Microwave-mediated heat transport in a quantum dot attached to leads

The thermoelectric effect in a quantum dot (QD) attached to two leads in the presence of microwave fields is studied by using the Keldysh nonequilibrium Green function technique. When the microwave is applied only on the QD and in the linear response regime, the main peaks in the thermoelectric figure of merit and the thermopower are found to decrease, with the emergence of a set of photon-induced peaks. Under this condition the microwave field cannot generate heat current or electrical bias voltage. Surprisingly, when the microwave field is applied only to one (bright) lead and not to the other (dark) lead or the QD, heat flows mostly from the dark to the bright lead, almost irrespective of the direction of the thermal gradient. We attribute this effect to microwave-induced opening of additional transport channels below the Fermi energy. The microwave field can change both the magnitude and the sign of the electrical bias voltage induced by the temperature gradient.     

Nanoscale thermal transport: Theoretical method and application

With the size reduction of nanoscale electronic devices, the heat generated by the unit area in integrated circuits will be increasing exponentially, and consequently the thermal management in these devices is a very important issue. In addition, the heat generated by the electronic devices mostly diffuses to the air in the form of waste heat, which makes the thermoelectric energy conversion also an important issue for nowadays. In recent years, the thermal transport properties in nanoscale systems have attracted increasing attention in both experiments and theoretical calculations. In this review, we will discuss various theoretical simulation methods for investigating thermal transport properties and take a glance at several interesting thermal transport phenomena in nanoscale systems. Our emphasizes will lie on the advantage and limitation of calculational method, and the application of nanoscale thermal transport and thermoelectric property.     

Thermoelectricity without absorbing energy from the heat sources

We analyze the power output of a quantum dot machine coupled to two electronic reservoirs via thermoelectric contacts, and to two thermal reservoirs – one hot and one cold. This machine is a nanoscale analogue of a conventional thermocouple heat-engine, in which the active region being heated is unavoidably also exchanging heat with its cold environment. Heat exchange between the dot and the thermal reservoirs is treated as a capacitive coupling to electronic fluctuations in localized levels, modeled as two additional quantum dots. The resulting multiple-dot setup is described using a master equation approach. We observe an “exotic” power generation, which remains finite even when the heat absorbed from the thermal reservoirs is zero (in other words the heat coming from the hot reservoir all escapes into the cold environment). This effect can be understood in terms of a non-local effect in which the heat flow from heat source to the cold environment generates power via a mechanism which we refer to as Coulomb heat drag. It relies on the fact that there is no relaxation in the quantum dot system, so electrons within it have a non-thermal energy distribution. More poetically, one can say that we find a spatial separation of the first-law of thermodynamics (heat to work conversion) from the second-law of thermodynamics (generation of entropy). We present circumstances in which this non-thermal system can generate more power than any conventional macroscopic thermocouple (with local thermalization), even when the latter works with Carnot efficiency.     

Reprint of : Thermoelectricity without absorbing energy from the heat sources

We analyze the power output of a quantum dot machine coupled to two electronic reservoirs via thermoelectric contacts, and to two thermal reservoirs – one hot and one cold. This machine is a nanoscale analogue of a conventional thermocouple heat-engine, in which the active region being heated is unavoidably also exchanging heat with its cold environment. Heat exchange between the dot and the thermal reservoirs is treated as a capacitive coupling to electronic fluctuations in localized levels, modeled as two additional quantum dots. The resulting multiple-dot setup is described using a master equation approach. We observe an “exotic” power generation, which remains finite even when the heat absorbed from the thermal reservoirs is zero (in other words the heat coming from the hot reservoir all escapes into the cold environment). This effect can be understood in terms of a non-local effect in which the heat flow from heat source to the cold environment generates power via a mechanism which we refer to as Coulomb heat drag. It relies on the fact that there is no relaxation in the quantum dot system, so electrons within it have a non-thermal energy distribution. More poetically, one can say that we find a spatial separation of the first-law of thermodynamics (heat to work conversion) from the second-law of thermodynamics (generation of entropy). We present circumstances in which this non-thermal system can generate more power than any conventional macroscopic thermocouple (with local thermalization), even when the latter works with Carnot efficiency.