Absorption enhancement of ultrathin crystalline silicon solar cells with frequency upconversion nanosphere arrays

A design of ultrathin crystalline silicon solar cells patterned with α-NaEr_(0.2)Y_(0.8)F_4 upconversion nanosphere(NSs) arrays on the surface was proposed. The light trapping performance ofα-NaEr_(0.2)Y_(0.8)F_4 NSs with different ratios of sphere diameter to sphere pitch was systematically studied by COMSOL Multiphysics. The influence of different NS diameters and ratio to the average optical absorption of ultrathin crystalline silicon solar cell was calculated, as well as the short circuit current densities. The results show that the average optical absorption of solar cells with 2.33 μm silicon covered by α-NaEr_(0.2)Y_(0.8)F_4 NSs of 100 nm in diameter and 5.2 in ratio has improved by 8.5% compared to planar silicon solar cells with the same thickness of silicon. The light trapping performance of different thicknesses of silicon solar cells with the optimized configuration of NSs was also discussed. The results indicate that our structure enhances the light absorption. The presented model will be the basis for further simulations concerning frequency upconversion of α-NaEr_(0.2)Y_(0.8)F_4 materials.     

A new proposal for Si tandem solar cell: Significant efficiency enhancement in 3C–SiC/Si

In order to considerable enhancement of the efficiency of silicon solar cells, in this paper, for the first time, we present a new proposal for silicon based tandem solar cells. For investigation of this idea, we have evaluated the characteristics of 3C–SiC/Si crystalline tandem solar cells connected series by a tunneling junction, under air mass 1.5 global irradiance spectrums. A 2D simulation including the effects of surface passivation, back surface field (BSF), and carrier tunneling have been performed to obtain the optical and electrical characteristics of single junction silicon, 3C–SiC, and finally the tandem cells. The obtained data illustrate that the best design parameters considering the experimental limitations can be obtained. High energy conversion efficiency for the proposed structure of 26.09% has been achieved for 3C–SiC/Si tandem structure driven by 20.49% and 17.86% conversion efficiencies of single junction Si and 3C–SiC solar cells, respectively. Our results justifies that the higher conversion efficiency of the Si-based tandem structure compared with 3C–SiC and Si cells stems from enhancement of open circuit voltage and fill factor parameter at the hands of decrease in short circuit current limited by the top 3C–SiC cell.     

Y2O3:Bi,Yb减反转光薄膜的制备及其性能研究

采用脉冲激光沉积(PLD)方法在湿法腐蚀后的Si(100)衬底上制备了Y₂O₃:Bi,Yb减反转光薄膜。所制备的薄膜在300~800 nm波长范围内的平均反射率最低至5.28%,同时在晶体硅太阳能电池最佳响应范围内的980 nm附近表现出了良好的下转光特性。与非减反下转光薄膜相比较,具有减反结构的Y₂O₃:Bi,Yb下转换薄膜的转光强度有了明显的提升。随着衬底腐蚀时间在一定范围内的延长,Bi³⁺和Yb³⁺的发射峰强度线性增大。该减反转光薄膜为太阳能电池效率提高提供了一种简单可行的方法。     

Passivation of black silicon boron emitters with atomic layer deposited aluminum oxide

The nanostructured surface – also called black silicon (b‐Si) – is a promising texture for solar cells because of its extremely low reflectance combined with low surface recombination obtained with atomic layer deposited (ALD) thin films. However, the challenges in keeping the excellent optical properties and passivation in further processing have not been addressed before. Here we study especially the applicability of the ALD passivation on highly boron doped emitters that is present in crystalline silicon solar cells. The results show that the nanostructured boron emitters can be passivated efficiently using ALD Al₂O₃ reaching emitter saturation current densities as low as 51 fA/cm². Furthermore, reflectance values less than 0.5% after processing show that the different process steps are not detrimental for the low reflectance of b‐Si. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Si_3N_4/Si表面Si生长过程的扫描隧道显微镜研究

利用原位扫描隧道显微镜和低能电子衍射分析了Si的纳米颗粒在Si3N4 /Si(111)和Si3N4 /Si(10 0 )表面生长过程的结构演变 .在生长早期T为 35 0— 10 75K范围内 ,Si在两种衬底表面上都形成高密度的三维纳米团簇 ,这些团簇的大小均在几个纳米范围内 ,并且在高温退火时保持相当稳定的形状而不相互融合 .当生长继续时 ,Si的晶体小面开始显现 .在晶态的Si3N4 (0 0 0 1) /Si(111)表面 ,Si的 (111)小面生长比其他方向优先 ,生长方向与衬底Si(111)方向一致 .最后在大范围内形成以 (111)为主的晶面 .相反 ,在非晶的Si3N4 表面 ,即Si3N4 /Si(10 0 ) ,Si晶体的生长呈现完全随机的方向性 ,低指数面如 (111)和 (10 0 )面共存 ,但它们并不占据主导地位 ,大部分暴露的小面是高指数面如 (113)面 .对表面生长过程进行了探讨并给出了合理的物理解释     

余弦光栅硅薄膜太阳能电池光吸收分析

设计了一维双层余弦共形光栅结构的单晶硅薄膜太阳能电池.利用时域有限差分法模拟计算了双层余弦共形光栅结构和对照组结构的吸收光谱;利用归一化光吸收密度的概念,定量分析了300~700nm和700~1 100nm两个波段的光吸收效率.结果表明双层共形光栅结构具有更好的全波段吸收效率,且在长波段余弦光栅比矩形光栅具有更好的光捕获和吸收作用.利用光吸收增强谱和电磁场强度分布图,分析了余弦光栅在长波段的吸收增强机理.通过计算短路电流密度,发现双层余弦共形光栅结构比平板结构太阳能电池的短路电流密度提高了79.5%,余弦光栅结构比矩形光栅结构的短路电流密度提高了8.5%.     

Design of a lattice-matched III–V–N/Si photovoltaic tandem cell monolithically integrated on silicon substrate

In this paper, we present a comprehensive study of high efficiencies tandem solar cells monolithically grown on a silicon substrate using GaAsPN absorber layer. InGaAs(N) quantum dots and GaAsPN quantum wells have been grown recently on GaP/Si susbstrate for applications related to light emission. For photovoltaic applications, we consider the GaAsPN diluted nitride alloy as the top junction material due to both its perfect lattice matching with Si and ideal bandgap energy for current generation in association with the Si bottom cell. Numerical simulation of the top cell is performed. The effect of layer thicknesses and doping on the cell efficiency are evidenced. In these structures a tunnel junction (TJ) is needed to interconnect both the top and bottom sub-cells. We compare the simulated performances of different TJ structures and show that the GaP(n+)/Si(p+) TJ is promising to improve performances of the current–voltage characteristic.     

Optical simulation of CsPbI3/TOPCon tandem solar cells with advanced light management

Monolithic perovskite/Si tandem solar cells (TSCs) have experienced rapid development in recent years, demonstrating its potential to exceed the Shockley-Queisser limit of single junction Si solar cells. Unlike typical organic-inorganic hybrid perovskite/silicon heterojunction TSCs, here we propose CsPbI₃/TOPCon TSC, which is a promising architecture in consideration of its pleasurable thermal stability and good compatibility with current PERC production lines. The optical performance of CsPbI₃/TOPCon TSCs is simulated by the combination of ray-tracing method and transfer matrix method. The light management of the CsPbI₃/TOPCon TSC begins with the optimization of the surface texture on Si subcell, indicating that a bifacial inverted pyramid with a small bottom angle of rear-side enables a further minimization of the optical losses. Current matching between the subcells, as well as the parasitic absorption loss from the front transparent conductive oxide, is analyzed and discussed in detail. Finally, an optimized configuration of CsPbI₃/TOPCon TSC with a 31.78% power conversion efficiency is proposed. This work provides a practical guidance for approaching high-efficiency perovskite/Si TSCs.     

Emergent Upconversion Sustainable Micro‐Optical Trapping Device

Ultrathin‐thickness single‐junction Si‐based solar cells can be developed to enhance photoelectric conversion efficiency (PECE) approaching to Shockley–Queisser limit. However, loss of short circuit current is a crucial factor that dramatically affects PECE improvement. Even though many studies have focused on rare reflector architecture for facilitating near‐infrared radiation absorption, PECE is still constraint due to its fabrication cost. Herein, an upconversion sustainable micro‐optical trapping device is reported. Using a systematic procedure, a high upconversion performance core–shell‐nanoparticles (CSNPs) structure is synthesized. Accordingly, silica diatom microporous frustule is a good electromagnetic field localization chamber, upon which CSNPs are embedded through a microassemble synthesis. This emerging device can be support on ultrathin‐thickness single‐junction Si‐based solar cells as a rare absorber with its low preparation cost. In the experiment, CSNPs upconversion optical density by surface plasmon resonance of Au nanoparticle's enhancement can be increased five‐time greater than NaYF₄ without SiO₂ coating. A finite difference time domain simulation and real color luminescence images in this study are also demonstrated.     

Dependence of Optical Absorption in Silicon Nanostructures on Size of Silicon Nanoparticles

The amorphous silicon nanoparticles (Si NPs) embedded in silicon nitride (SiN_x) films prepared by helicon wave plasma-enhanced chemical vapor deposition (HWP-CVD) technique are studied. From Raman scattering investigation, we determine that the deposited film has the structure of silicon nanocrystals embedded in silicon nitride (nc-Si/SiNx) thin film at a certain hydrogen dilution amount. The analysis of optical absorption spectra implies that the Si NPs is affected by quantum size effects and has the nature of an indirect-band-gap semiconductor. Further, considering the effects of the mean Si NP size and their dispersion on oscillator strength, and quantum-confinement, we obtain an analytical expression for the spectral absorbance of ensemble samples. Gaussian as well as lognormal size-distributions of the Si NPs are considered for optical absorption coefficient calculations. The influence of the particlesize-distribution on the optical absorption spectra was systematically studied. We present the fitting of the optical absorption experimental data with our model and discuss the results.     

硅薄膜太阳电池表面纳米线阵列光学设计

陷光结构的优化是增加硅薄膜太阳电池光吸收进而提高其效率的关键技术之一. 以硅纳米线阵列为代表的光子晶体微纳陷光结构具有突破传统陷光结构Yablonovith极限的巨大潜力. 通常硅纳米线阵列可以用作太阳电池的增透减反层、轴向p-n结、径向p-n结. 针对以上三种应用, 本文运用有限时域差分(FDTD)法系统研究了硅纳米线阵列在 300-1100 nm 波段的光学特性. 结果表明, 当硅纳米线作为太阳电池的减反层时, 周期P=300 nm, 高度H=1.5 μm, 填充率(FR)为0.282条件下时, 反射率最低为7.9%. 当硅纳米线作为轴向p-n结电池时, P=500 nm, H=1.5 μm, FR=0.55条件下纳米线阵列的吸收效率高达22.3%. 硅纳米线作为径向p-n结电池时, 其光吸收主要依靠纳米线, 硅纳米线P=300 nm, H=6 μm, FR= 0.349 条件下其吸收效率高达32.4%, 进一步提高其高度吸收效率变化不再明显. 此外, 本文还分析了非周期性硅纳米线阵列的光学性质, 与周期性硅纳米线阵列相比, 直径随机分布和位置随机分布的硅纳米线阵列都可以使吸收效率进一步提高, 相比于周期性硅纳米线阵列, 优化后直径随机分布的硅纳米线阵列吸收效率提高了39%, 吸收效率为27.8%. 本文运用FDTD法对硅纳米线阵列的光学特性进行设计与优化, 为硅纳米线阵列在太阳电池中的应用提供了理论支持.     

Plasmon enhanced light trapping in thin film GaAs solar cells by Al nanoparticle array

Light trapping is a crucial factor to enhance the performance of thin film solar cells. For effective light trapping, we introduced Al nanoparticle array on the top and rear surface of thin film GaAs solar cells. The effect of both array on the optical absorption and current density of solar cells is investigated by using finite difference time domain (FDTD) method. The optimization process of top and rear array in solar cells is done systematically. The results indicate that by plasmonic action of arrays, the optical absorption is significantly enhanced and optimized structure yields a current density of 25.77 mA/cm². These enhancements are mainly attributed to surface plasmon effects induced by Al nanoparticles and the light grating properties of the arrays.     

Enhanced broadband light absorption in silicon film by large-size lumpy silver particles

Broadband light absorption enhancement in crystalline silicon thin-film solar cells by rear-located 400 nm lumpy silver particles has been studied, based on the theoretical simulations of 3D finite-difference time-domain method. By simulations, we have investigated the light scattering properties of 400 nm lumpy Ag particles and put it to silicon thin-film solar cells. In addition, the varying rear-located Ag particles coverage and two surface situations of silicon films, which could influence on the light absorption of solar devices, have also been comprehensively considered. The results have shown that rear-located 400 nm lumpy Ag particles would enhance the absorption in silicon films in a broadband range. And it has been proved that 20 % coverage density of rear-located Ag particles is optimal for improving the light absorption of smooth silicon thin-film solar devices. When we create rough surface on one or both sides of silicon films, the absorbed light would further increase, and the theoretical maximum enhancement is 15.1 % compared with the smooth silicon thin-film solar cell without Ag particles.     

Blue laser lithography for making antireflective submicron structures on silicon

The application of blue laser lithography for creating antireflective submicron structures on a crystalline silicon substrate was evaluated. The assembled blue laser lithography system was obtained by modifying a commercial blue laser optical pickup head and consisting of a 405-nm-wavelength blue laser and a 0.85-numerical-aperture objective lens. Si substrates were patterned with submicron column patterns of various periods and aspect ratios by blue laser lithography using a sputtered Ge-Sb-Sn-O layer as a resist. The reflectance of the patterned Si substrate decreased to 3% on average in the 300–1000 nm wavelength range, with a low sensitivity to the angle of incident light. Such patterned substrates showed potential for application in crystalline Si solar cells.     

Optical band gap of Si nanoclusters

We discuss the nature of the optical transitions in porous silicon and in Si nanoclusters in the light of recent theoretical calculations. The accuracy of the different techniques used to calculate the band gap of Si nanoclusters is analyzed. We calculate the electronic structure of crystallites in the Si-III (BC8) crystalline phase which is known to have a direct gap and we examine the effect of quantum confinement on clusters of SiGe alloy and amorphous silicon. The comparison with the experiments for all the systems suggests the possibility of different channels for the radiative recombination.     

Improving the efficiency of thin film tandem solar cells by plasmonic intermediate reflectors

Thin film tandem solar cells made of amorphous and microcrystalline silicon provide renewable energy at the benefit of low material consumption. As a drawback, these materials do not posses the high carrier mobilities of their crystalline counterpart which limits the feasible material thickness. For maintaining the light absorption as high as possible, photon management is required. Here we show that metallic nanodiscs that sustain localized plasmon polaritons can increase the efficiency of such solar cells if they are incorporated into the dielectric intermediate reflector separating the top and the bottom cell. We provide quantitative estimates for the possible absorption enhancement of optimized bi-periodic nanodiscs that are feasible for fabrication. Emphasis is also put on discussing the impact of obliquely incident sun light on the solar cell performance.     

Microstructure evolution and passivation quality of hydrogenated amorphous silicon oxide(a-SiOx:H) on〈100〉- and 〈111〉-orientated c-Si wafers

Hydrogenated amorphous silicon oxide(a-SiOx:H) is an attractive passivation material to suppress epitaxial growth and reduce the parasitic absorption loss in silicon heterojunction(SHJ) solar cells. In this paper, a-SiOx:H layers on different orientated c-Si substrates are fabricated. An optimal effective lifetime(τ(eff)) of 4743 μs and corresponding implied opencircuit voltage(iV(oc)) of 724 mV are obtained on〈100〉-orientated c-Si wafers. While τ(eff) of 2429 μs and iV_oc of 699 mV are achieved on 111-orientated substrate. The FTIR and XPS results indicate that the a-SiOx:H network consists of SiOx(Si-rich), Si–OH, Si–O–SiHx, SiO2 ≡ Si–Si, and O3 ≡ Si–Si. A passivation evolution mechanism is proposed to explain the different passivation results on different c-Si wafers. By modulating the a-SiOx:H layer, the planar silicon heterojunction solar cell can achieve an efficiency of 18.15%.     

纳米表面二维周期半圆凹槽增强硅薄膜太阳能电池光吸收

利用时域有限差分方法, 研究硅薄膜上下表面周期半圆凹槽结构对于太阳光吸收的增强效应. 研究发现这种结构可以实现太阳光宽波段的光吸收增强, 通过调节SiO₂表面减反层厚度和凹槽半径长度来实现薄膜太阳能电池最大的光吸收, 并实现了波长在300-1000 nm范围的太阳光吸收总能量比没有这种 结构下硅薄膜光吸收提高了约117%. 关键词： 硅薄膜 半圆凹槽 吸收增强     

电极对CuPc/C60双层异质结有机太阳能电池光学性能的影响

采用传输矩阵法的光学模型以及MATLAB软件模拟了电极对CuPc/C₆₀双层异质结有机太阳能电池光学性能的影响。模拟结果表明:当把微腔结构引入到双层异质结电池时,对于入射电极,发现活性层的吸光率主要受其反射相移的影响而非其透射率,并且通过变化入射电极相移调节层到合适厚度可以使活性层吸光率相比于传统器件增加很多;而当把正负折射率交替的光子晶体引入到电池中作为背电极时,发现活性层的吸光率和背电极反射率、反射相移都有很大关系,在获得高反射率的同时可以通过调节背电极厚度从而使活性层在整个吸收光谱内的吸光率大于传统器件。