AlN/Si3N4纳米多层膜的外延生长与力学性能

采用射频磁控溅射方法制备单层AlN, Si₃N₄薄膜和不同调制周期的AlN/Si₃N₄纳米多层膜.采用X射线衍射仪、高分辨透射电子显微镜和纳米压痕仪对薄膜进行表征.结果发现,多层膜中Si₃N₄层的晶体结构和多层膜的硬度依赖于Si₃N₄层的厚度.当AlN层厚度为4.0nm、 Si₃N₄层厚度 关键词： 3N₄纳米多层膜')" href="#">AlN/Si₃N₄纳米多层膜 外延生长 应力场 超硬效应     

SiO2的赝晶化及AlN/SiO2纳米多层膜的超硬效应

采用反应磁控溅射法制备了一系列不同SiO₂层厚度的AlN/SiO₂纳米多层膜，利用X射线衍射仪、高分辨透射电子显微镜和微力学探针表征了多层膜的微结构和力学性能，研究了SiO₂层在多层膜中的晶化现象及其对多层膜生长方式及力学性能的影响. 结果表明，由于受AlN六方晶体结构的模板作用，溅射条件下以非晶态存在的SiO₂层在其厚度小于0.6 nm时被强制晶化为与AlN相同的六方结构赝晶体并与AlN形成共格外延生长. 由于不同模量的两调制层存在晶格错配度，多层膜中产生了拉、压交变的应力场，使得多层膜产生硬度升高的超硬效应. SiO₂随层厚的进一步增加又转变为以非晶态生长，多层膜的外延生长结构受到破坏，其硬度也随之降低. 关键词： 2纳米多层膜')" href="#">AlN/SiO₂纳米多层膜 赝晶化 应力场 超硬效应     

Si3N4在h-AlN上的晶体化与AlN/Si3N4纳米多层膜的超硬效应

采用反应磁控溅射法制备了一系列具有不同Si3N4层厚度的AlN/Si3N4纳米多层膜,利用X射线衍射仪、高分辨透射电子显微镜和微力学探针表征了多层膜的微结构和力学性能.研究了Si3N4层在AlN/Si3N4纳米多层膜中的晶化现象及其对多层膜生长结构与力学性能的影响.结果表明,在六方纤锌矿结构的晶体AlN调制层的模板作用下,通常溅射条件下以非晶态存在的Si3N4层在其厚度小于约1nm时被强制晶化为结构与AlN相同的赝形晶体,AlN/Si3N4纳米多层膜形成共格外延生长的结构,相应地,多层膜产生硬度升高的超硬效应.Si3N4随层厚的进一步增加又转变为非晶态,多层膜的共格生长结构因而受到破坏,其硬度也随之降低.分析认为,AlN/Si3N4纳米多层膜超硬效应的产生与多层膜共格外延生长所形成的拉压交变应力场导致的两调制层模量差的增大有关.     

TiN/Al2O3纳米多层膜的共格外延生长及超硬效应

采用多靶磁控溅射法制备了一系列具有不同Al₂O₃调制层厚度的TiN/Al₂O₃纳米多层膜. 利用X射线能量色散谱、X射线衍射、扫描电子显微镜、高分辨透射电子显微镜和微力学探针表征了多层膜的成分、微结构和力学性能. 研究结果表明，在TiN/Al₂O₃纳米多层膜中，单层膜时以非晶态存在的Al₂O₃层在厚度小于1.5 nm时因TiN晶体层的模板效应而晶化，并与TiN层形成共格外延生长，相应地，多层膜产生硬度明显升高的超硬效应，最高硬度可达37.9 GPa. 进一步增加多层膜中Al₂O₃调制层的层厚度，Al₂O₃层逐渐形成非晶结构并破坏了多层膜的共格外延生长，使得多层膜的硬度逐步降低. 关键词： 2O₃纳米多层膜')" href="#">TiN/Al₂O₃纳米多层膜 外延生长 非晶晶化 超硬效应     

Si3N4的晶体化和ZrN/Si3N4纳米多层膜的超硬效应

研究了Si₃N₄层在ZrN/Si₃N₄纳米多层膜中的晶化现象及其对多层膜微结构与力学性能的影响. 一系列不同Si₃N₄层厚度的ZrN/Si₃N₄纳米多层膜通过反应磁控溅射法制备. 利用X射线衍射仪、高分辨透射电子显微镜和微力学探针表征了多层膜的微结构和力学性能. 结果表明，由于受到ZrN调制层晶体结构的模板作用，溅射条件下以非晶态存在的Si₃N₄层在其厚度小于0.9 nm时被强制晶化为NaCl结构的赝晶体，ZrN/Si₃N₄纳米多层膜形成共格外延生长的柱状晶，并相应地产生硬度升高的超硬效应. Si₃N₄随层厚的进一步增加又转变为非晶态，多层膜的共格生长结构因而受到破坏，其硬度也随之降低.     

反应溅射VN/SiO2纳米多层膜的微结构与力学性能

采用V和SiO₂靶通过反应溅射方法制备了一系列具有不同SiO₂和VN调制层厚的VN/SiO₂纳米多层膜. 利用X射线衍射、X射线能量色散谱、高分辨电子显微镜和微力学探针表征了多层膜的微结构和力学性能. 结果表明：在Ar，N₂混和气体中，射频反应溅射的SiO₂薄膜不会渗氮. 单层膜时以非晶态存在的SiO₂，当其厚度小于1nm时，在多层膜中因VN晶体层的模板效应被强制晶化，并与VN层形成共格外延生长. 相应地，多层膜的硬度得到明显提高，最高硬度达34GPa. 随SiO₂层厚度的进一步增加，SiO₂层逐渐转变为非晶态，破坏了与VN层的共格外延生长结构，多层膜硬度也随之降低. VN调制层的改变对多层膜的生长结构和力学性能也有影响，但并不明显. 关键词： 2纳米多层膜')" href="#">VN/SiO₂纳米多层膜 共格外延生长 非晶晶化 超硬效应     

Si3N4/Si表面Si生长过程的扫描隧道显微镜研究

利用原位扫描隧道显微镜和低能电子衍射分析了Si的纳米颗粒在Si₃N₄/Si(111)和Si₃N₄/Si(100)表面生长过程的结构演变.在生长早期T为350—1075K范围内,Si在两种衬底表面上都形成高密度的三维纳米团簇,这些团簇的大小均在几个纳米范围内,并且在高温退火时保持相当稳定的形状而不相互融合.当生长继续时,Si的晶体小面开始显现.在晶态的Si₃N₄(0001)/S 关键词： 氮化硅 扫描隧道显微镜 纳米颗粒     

Si3N4的晶体化和ZrN/Si3N4纳米多层膜的超硬效应

研究了Si3N4层在ZrN/Si3N4纳米多层膜中的晶化现象及其对多层膜微结构与力学性能的影响.一系列不同Si3N4层厚度的ZrN/Si3N4纳米多层膜通过反应磁控溅射法制备.利用X射线衍射仪、高分辨透射电子显微镜和微力学探针表征了多层膜的微结构和力学性能.结果表明,由于受到ZrN调制层晶体结构的模板作用,溅射条件下以非晶态存在的Si3N4层在其厚度小于0.9 nm时被强制晶化为NaCl结构的赝晶体,ZrN/Si3N4纳米多层膜形成共格外延生长的柱状晶,并相应地产生硬度升高的超硬效应.Si3N4随层厚的进一步增加又转变为非晶态,多层膜的共格生长结构因而受到破坏,其硬度也随之降低.     

AIN/Si3N4 纳米多层膜的外延生长与力学性能

采用射频磁控溅射方法制备单层AlN,Si3N4薄膜和不同调制周期的AlN/S3N4纳米多层膜.采用X射线衍射仪、高分辨透射电子显微镜和纳米压痕仪对薄膜进行表征.结果发现,多层膜中Si3N4层的晶体结构和多层膜的硬度依赖于Si3N4层的厚度.当AlN层厚度为4.0 nm、Si3N4层厚度为0.4nm时,AlN和Si3N4层共格外延生长,多层膜形成穿过若干个调制周期的柱状晶结构,产生硬度升高的超硬效应.随着Si3N4层厚的增加,Si3N4层逐步形成非晶并阻断了多层膜的共格外延生长,多层膜的硬度迅速降低,超硬效应消失.采用材料热力学和弹性力学计算了Si3N4层由晶态向非晶转变的临界厚度.探讨了AlN/Si3N4纳米多层膜出现超硬效应的机理.     

TiN/TiB2异结构纳米多层膜的共格生长与力学性能

采用多靶磁控溅射法制备了一系列具有不同TiB₂调制层厚度的TiN/TiB_{2纳米多层膜.利用x射线衍射仪、高分辨电子显微镜和微力学探针研究了TiB2层厚变化对多层膜生长结构和力学性能的影响.结果表明，在fcc-TiN层(111)生长面的模板 作用下，原为非晶态的TiB2层在厚度小于2.9nm时形成hcp晶体态，并与fcc-TiN 形成共格外延生长；其界面共格关系为{111}TiN//{0001}TiB2，〈110〉TiN//〈1120〉TiB2.由于共格界面存在晶格失配 度，多层膜中形成拉、压交变的应力场，导致多层膜产生硬度和弹性模量升高的超硬效应， 最高硬度和弹性模量分别达到46.9GPa和465GPa.继续增加TiB2层的厚度，TiB2形成非晶态并破坏了与TiN层的共格外延生长，多层膜形成非晶TiN层和非晶TiB< sub>2层交替的调制结构，其硬度和弹性模量相应降低. 关键词： 2}纳米多层膜')" href="#">TiN/TiB₂纳米多层膜 共格生长 晶体化 力学性能     

Crystallization of amorphous Si3N4 and superhardness effect in HfC/Si3N4 nanomultilayers

HfC/Si₃N₄ nanomultilayers with various thicknesses of Si₃N₄ layer have been prepared by reactive magnetron sputtering. Microstructure and mechanical properties of the multilayers have been investigated. The results show that amorphous Si₃N₄ is forced to crystallize and grow coherently with HfC when the Si₃N₄ layer thickness is less than 0.95 nm, correspondingly the multilayers exhibit strong columnar structure and achieve a significantly enhanced hardness with the maximum of 38.2 GPa. Further increasing Si₃N₄ layer thickness leads to the formation of amorphous Si₃N₄, which blocks the coherent growth of multilayer, and thus the hardness of multilayer decreases quickly.     

AlN/BN纳米结构多层膜微结构及力学性能

用射频磁控溅射法制备了AlN,BN单层膜及AlN/BN纳米多层膜.采用X射线衍射仪、高分辨率透射电子显微镜和纳米压痕仪对薄膜结构进行表征.分析表明：单层膜AlN为w-AlN结构,BN为非晶相.AlN/BN多层膜中BN的结构与BN层厚有关.当BN层厚小于0.55nm时,由于AlN层模板的作用,BN发生了外延生长,BN与AlN的结构相同;当BN层厚大于0.74nm时,BN为非晶.AlN/BN多层膜的硬度也与BN层的厚度有关.当BN层厚为1—2个分子层时,AlN/BN多层膜具有超硬效应;当BN层厚增加到0.74 关键词： AlN/BN多层膜 BN结构 超硬效应     

Radiation damage effects on power VDMOS devices with composite SiO2–Si3N4 films

Total dose effects and single event effects on radiation-hardened power vertical double-diffusion metal oxide semiconductor (VDMOS) devices with composite SiO₂-–Si₃N₄ film gate are investigated. The relationships among the important electrical parameters of the samples with different thickness SiO₂-–Si₃N₄ films, such as threshold voltage, breakdown voltage, and on-state resistance in accumulated dose, are discussed. The total dose experiment results show that the breakdown voltage and the on-state resistance barely change with the accumulated dose. However, the relationships between the threshold voltages of the samples and the accumulated dose are more complex, not only positive drift, but also negative drift. At the end of the total dose experiment, we select the group of samples which have the smaller threshold voltage shift to carry out the single event effect studies. We find that the samples with appropriate thickness ratio SiO₂-–Si₃N₄ films have a good radiation-hardening ability. This method may be useful in solving both the SEGR and the total dose problems with the composite SiO₂-–Si₃N₄ films.     

Improving the tribological performances of graphite-like carbon films on Si3N4 and SiC by using Si interlayers

Si interlayers were used to obtain the excellent tribological performances of graphite-like carbon (GLC) film on silicon nitride (Si₃N₄) and silicon carbide (SiC). The microstructure and mechanical characteristics of the as-prepared GLC films with Si interlayers were investigated by scanning electron microscopy, Raman spectroscopy, nanoindention and scratch test. The tribological behaviors of GLC-coated and uncoated Si₃N₄ and SiC were comparatively studied by a ball-on-disc tribo-meter in both dry and water environments. Results showed that the Si interlayers were dense and bonded well with both the substrates and GLC layers. The as-prepared GLC films exhibited excellent tribological performances in both dry and water environments. More importantly, the stably mild wear without any delamination was obtained in water by using Si interlayer. The mechanisms of friction reduction and anti-wear performances of GLC films on the two ceramics with Si interlayers under different environmental conditions were discussed, as well as the corresponding models were deduced.     

Evaluation of fracture toughness of ZrO2 and Si3N4 engineering ceramics following CO2 and fibre laser surface treatment

The fracture toughness property (K_1C) of Si₃N₄ and ZrO₂ engineering ceramics was investigated by means of CO₂ and a fibre laser surface treatment. Near surface modifications in the hardness were investigated by employing the Vickers indentation method. Crack lengths and the crack geometry were then measured by using the optical microscopy. A co-ordinate measuring machine was used to investigate the diamond indentations and to measure the lengths of the cracks. Thereafter, computational and analytical methods were employed to determine the K_1C. An increase in the K_1C of both ceramics was found by the CO₂ and the fibre laser surface treatment in comparison to the as-received surfaces. The K_1C of the CO₂ laser radiated surface of the Si₃N₄ was over 3% higher in comparison to that of the fibre laser treated surface. This was by softening of the near surface layer of the Si₃N₄ which comprised of lowering of hardness, which in turn increased the crack resistance. The effects were not similar in ZrO₂ ceramic to that of the Si₃N₄ as the fibre laser radiation in this case had produced an increase of 34% compared to that of the CO₂ laser radiation. This occurred due to propagation of lower crack resulting from the Vickers indentation test during the fibre laser surface treatment which inherently affected the end K_1C through an induced compressive stress layer. The K_1C modification of the two ceramics treated by the CO₂ and the fibre laser was also believed to be influenced by the different laser wavelength and its absorption co-efficient, the beam delivery system as well as the differences in the brightness of the two lasers used.     

Preparation, characterization and luminescence properties of porous Si3N4 ceramics with Eu2O3 as sintering additive

Porous Si₃N₄ ceramics with photoluminescence properties were prepared by pressureless sintering using α-Si₃N₄ powder as raw material and Eu₂O₃ as sintering additive. Chemical composition, phase formation, microstructure and photoluminescence properties of porous Si₃N₄ ceramics were studied by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence measurements (PL/PLE). The results show that single Eu₂O₃ additive promotes α→β transformation but not significant densification. A broad band emission center at 570 nm assigned to Eu²⁺ is observed, Eu³⁺ in Eu₂O₃ is (partially) converted to Eu²⁺ by reaction with Si₃N₄, which results in a lower β aspect ratio and β-content compared to the other Ln (Ln=lanthanide) oxide additives.